Search Documents

By David B. George

Kennecott recently completed an $880 million modernization and expansion of its smelter and refinery to process all concentrates from the Bingham Canyon mine. This is the first application of Kennecott-Outokumpu Flash Converting. Molten material movement by overhead cranes is eliminated and high levels of oxygen enrichment result in very low process gas volumes and exceptionally control of sulfur oxide emissions. All existing in-plant hygiene, safety, and environmental regulations will be met and the smelter is positioned for anticipated more stringent future regulations. Sulfur capture is 99.9 percent resulting in sulfur dioxide emissions less than the 112 kg/hr Air Permit limit, making the smelter the cleanest in the world.

Jan 1, 1996

By J. Pesl, U. Kemey, F. Sauert

"The CONTOP® smelting cyclone is a water-cooled, upright, high-intensity smelting reactor. The technology for the reactor was initially developed and brought into industrial-scale operation in the area of non-ferrous metallurgy. The two largest smelting cyclones were built with a capacity of 32 tons per hour of copper concentrate mix.The newest industrial CONTOP® plant treats up to five tons per hour of zinc-bearing residues including EAF dust. The highly concentrated zinc-lead oxide produced is sold to the zinc industry. The slag fulfills the leaching criteria and is used in waterway construction. The heat transferred to the cyclone cooling system and the off-gas boiler produces steam from which power is generated in a turbine.V AI has erected a new CONTOP® demonstration plant at MEFOS, Lulea, Sweden. A zinc volatilization rate of 90% was achieved during hot commissioning with Swedish EAF dust.Treatment costs in the range of 85 to 100 EUR per ton were estimated in a feasibility study on the treatment of 73,000 and 57 ,000 tons EAF dust for a group of steelmaking mills in Southern Europe."

Jan 1, 2000

By Yunhua Gan, Xiaowen Chen, Yang Tong

Experimental studies of electro-spraying were carried out using ethanol as fuel in a microcombustor under combined electric field. And the effects of different electro-spraying modes on the combustion efficiency were analyzed. Results showed that when ring electrode potential was invariant, there were four different electro-spraying modes with the variations of nozzle potentials, which were varying with the flow of ethanol. The cone-jet mode was the stablest one during the whole experimental process. The atomized ethanol was ignited and combusted stably near the steel mesh, the combustion efficiency increased firstly and then decreased along with the increasing of the equivalent ratios, reached the maximum values when the equivalent ratio equal to 1.0. And the maximum values were the highest at the cone-jet mode, and the lowest at the pulsed-jet mode.

Jan 1, 2016

By KNona C. Liddell

The ion interaction model Pitzer proposed twenty years ago is today the most widely used method for calculation of osmotic coefficients and electrolyte and single ion activity coefficients in aqueous solutions. This is due in part to the accuracy of the results that have been obtained for many concentrated electrolytes. An additional factor is that, compared to alternative activity coefficient models, there are many more parameter values available for the Pitzer equations. The important features of this model are reviewed. Published parameter values for Co, Ni, Cu, Zn and Fe are tabulated, and applications of interest in the aqueous processing of these metals are described.

Jan 1, 1993

By Arthur W. Cooper

This paper contains a review of the development of blast furnace? slag handling and processing technology in the Ironmaking industry over the past 30 years, with an emphasis on economic and environmental factors. The requirements and practice of air-cooling slag for use as aggregate and of pelletizing and granulating slag for use in cement manufacture are described. The operation of slag pits, slag pots or ladles, the slag pelletizer and early granulation systems are compared with the new continuous .granulation, dewatering and handling systems developed in the past decade.

Jan 1, 1992

By H. Shang

The materials science and metallurgical engineering communities have expended enonnous resources in developing high fidelity process models. Exploiting these Models for Predictive Optimization (MPO) and Control (MPC) is a new frontier in Materials Process Engineering that will lead to exceptional process perfonnance. This paper will begin with a short survey of the development of high quality process models available in the literature and a discussion of how these could be used to improve process operation. A summary of the current "state-of-the-art" in process automation technologies and the traditional framework in which these technologies are deployed will be presented. An illustration of the use of MPO in process design and operations will be presented for the continuous casting of steel. In addition, a simple run-out table simulation will be used to demonstrate the power of the MPC technique.

Jan 1, 2003

By D. D. Rodier

Most zinc concentrates contain some silver and varying amounts of such valuable trace elements as gold, indium, germanium and gallium. With increasing similarities in plant installations, the predominance of electrolyte process and the increasing environmental constraints on iron disposal, it is essential that zinc smelters optimize the recovery of any valuable elements in their feed stocks. The process options, to date, of smelting, flotation or leaching of silver-rich leach residues cannot be applied economically to all installations. It is therefore necessary that new innovative processes, to recover silver and other valuable metals from relatively low grade feeds, be developed. This paper attempts to place this strategy in the context of today's constraints and will also provide a simple evaluation tool for any process alternatives.

Jan 1, 1990

By V. P. Keran

The lead and copper smelting processes employed by Mount Isa Mines Limited, Mount Isa, Australia, are used to illustrate an operating viewpoint of some problems and solutions encountered in existing commercial sulphide smelters. The smelting processes discussed; include updraught sintering, blast furnace and reverberatory smelting, and converting. Selected examples are given of methods implemented, and options available, to improve the productivity and efficiency of conventional smelting processes.

Jan 1, 1983

By G. Coryell, S. Blaskovich

"A computer model has been developed to simulate the flash furnace and converter operations at the ASARCO Hayden Copper Smelter. The focus of the modeling was to optimize the converter operation to eliminate high matte level episodes in the flash furnace. These episodes (reducing feed to the furnace) resulted from the lack of converter operation scheduling. The model provided ""what if?"" scheduling scenarios that led to increased efficiency of the converter and flash furnace operations.This paper discusses alternatives studied to optimize the converter operation and the development of the computer modeling program, including implementation of the project. The discussion details the results of the project including the conversion from batch to a real time converter scheduling process. IntroductionASARCO's Hayden Smelter consists of a fluid bed drying system, an Inco oxygen flash smelting furnace, Peirce Smith converters, two anode furnaces and two casting wheels, gas cleaning plant, 2800 stpd sulfuric acid plant, 650 stpd oxygen plant and 200 gpm water treatment plant. The process flow sheet of the plant is shown in Figure 1.Over the past several years, the Hayden smelter has been involved in productivity improvement and cost reduction programs. This has been necessary to become a low cost copper producer in today's market. Part of the productivity improvement program was the use of process control to streamline the flash furnace and converter operations. Process control, through the use of computers and electronic controllers, has played an increasingly important role in optimizing processes in the Hayden Plant since the startup of the Inco flash furnace in 1983."

Jan 1, 1989

By Fuqiang Zheng, Shuai Wang, Ting Duan, Yufeng Guo, Tao Jiang, Andrew Yakovlevich Travyanov

Organic compound binder can effectively enhance the strength of green pellet and reduce the addition amount of binder during pelletizing. However, compared with traditional bentonite binder pellet, the compressive strength of the preheated and roasted pellets significantly declined. It is of significance to resolve this problem for the application of organic compound binder. In this paper, magnetite concentrate was used as raw material, carboxymethyl cellulose (CMC)- bentonite compound was used as binder, characteristics of preheated and roasted pellets and the effects of additives on that were systematically studied, The results show that sodium acetate can effectively improve the characteristics of the finished compound binder pellets. The compressive strength of the preheated and roasted pellets were increased by 52/N·p-1 and 342/N·p-1 respectively when the addition amount of sodium acetate is 2.2%wt of compound binder. Moreover, sodium acetate has no adverse effect on pelletizing process and drying characteristics of green balls.

Jan 1, 2015

By Musa Karakus

In an attempt to explain the phenomena of lead entrainment during Cu drossing of lead bullion, two different synthetic lead bullions were heated to 1050°C, cooled slowly to various temperatures, and then quenched. The morphology and composition of dross particles that form when Mn is used to desulphurize bullion also were examined. Polished sections of these pyrometallurgical products were examined by process mineralogical techniques to identify the impurity phases, determine their chemical compositions, examine the morphology of the impurity phases and evaluate the potential for lead entrainment in such crystals, and characterize pre-quench and quench-generated phases. The phases crystallized were metallic lead, metallic copper, galena, chalcocite, albandite, Cu14.4Pb2S9. and 5.5Pb2S3.5. Metallic copper formed isometric skeletal crystals, chalcocite formed platy and skeletal crystals, and 1formed crystals and eutectic intergrowth with chalcocite and Cu14.4Pb2S9 or Cu5.5Ph2S3.5. The pre-quench crystals are larger and usually exhibit skeletal forms; the quench-generated phases are only a few micrometers across and disseminated throughout the lead matrix. Skeletal crystals of metallic copper and chalcocite form three dimensional networks that entrain large amounts of metallic lead.

Jan 1, 1989

By J. B. Winter

The present Inspiration Consolidated Copper Company Smelter/Acid Plant complex located near Miami, Arizona, was designed and built specifically to conform to the ambient air quality standards imposed by the Federal Clean Air Act of 1971. The present plant replaced a facility which had been in operation since 1915. The electric furnace, siphon converters and acid plant complex were commissioned in May, 1974 (1). At that time, the Plant was considered to be one of the most extensively monitored and instrumented facilities of its kind in the world. Several control areas were located in close proximity to the controlled process, in addition to so-called central control rooms in the Smelter and Acid Plant. The control rooms were staffed with officials below the foreman level. Instrumentation consisted of conventional analog devices, except for a computer used in monitoring ambient air environmental conditions and limited use of programmable logic controllers. The harsh service conditions prevalent in the plant rendered a significant portion of the instrumentation unreliable and, in many cases, inoperable. Failure of the facility to obtain the total sulfur collection for which it was designed was, in part, due to serious inadequacies in control system logic and sulfur recovery averaged 79% in the early years. After careful study of the smelting process, engineering hardware and high labor cost inherent in the organizational structure, management made a judgement decision to convert to centralized control of the process with high level supervision 24 hours per day. A distributed digital control system with supervisory arid data acquisition/information reporting computers was selected to satisfy the requirement of central control. Operations are now controlled and coordinated from a primary control room in the Smelter and a satellite control area in the Acid Plant.

Jan 1, 1983

By G. Nazari

ERAMET, through its subsidiary COMILOG, have rights to a rich niobium and rare earth deposit inGabon. The Mabounié deposit, is located 50 kmfromthe town of Lambaréné, in a fairly remote location. ERAMET has been developing a process to recover value metals for several years, and approached Hatch Ltd. to design a sizeable Demonstration Plant to help them further optimize the process, and prove the flowsheet is technically viable. The process employs concentration techniques to recover an upgraded Nb/REE feed material for processing in the subsequent leach step. Rare earths and niobium are selectively leached, and subsequently precipitated. Following precipitation, rare earths undergo bulk separation and are purified to produce LRE and mixed MRE/HRE products, which will be further processed by Third Parties. This paper provides a high-level overview of the process, summarizes the motivation for a Demonstration Plant in the vicinity of the deposit, and discusses technical challenges faced during the flowsheet definition and design phase. Key challenges are focused on and summaries of the methodologies used to address each challenge, as well as the solutions to overcome the challenges, are discussed. The paper provides motivation for further process simplification and concludes with a project update.

By M. D. Light

An intelligent control system (ICS) is being developed for ferrous iron oxidation by Thiobacillus ferroxitdans. The ICS provides computerized data acquisition and' control of process variables (temperature, Eh, pH, dissolved oxygen arid carbon dioxide concentrations and dilution rate) to maintain the ferrous iron oxidation at the highest possible rate. The ICS uses fuzzy logic for analysis of data inputs and implementation of control strategies. T:his paper provides preliminary information on the development of the ICS and? its operation.

Jan 1, 1991

By Chuanfu Zhang, Jinliang Wang

"Brickless reaction shaft is the latest progress for flash smelting furnace. However, there are many factors influence the melting point of the freeze slag inside brickless reaction shaft, and their variational regularities are not obvious, thus, it is difficult for conventional methods to analyze accurately the complex data. In this research, the experiment data of slag melting point were processed based on optimal discrimination plane. For this method, two orthogonal vectors were firstly built up based on the Fisher's criterion, and then the experiment data were projected onto the two vectors, thus, two-dimensional feature vectors were extracted as criteria to determine the factors effect degree on the slag melting point. Results show that the CaO content is the greatest factor to the melting point of the freeze slag inside brickless reaction shaft, the content of Fe3O4, SiO2, Cu2 O and MgO is the second, and the FeO content is the last.IntroductionBrickless reaction shaft is the latest progress of flash smelting furnace reaction shaft. To research the influence factors on the slag melting point inside the brickless reaction shaft is significant to form freeze slag with compact structure, good heat insulation, certain intensity, appropriate thickness and reasonable distribution, to extend furnace life, to reduce energy consumption, and to promote safe production.However, due to the complex components, there are many factors influence the melting points of the freeze slag inside brickless reaction shaft, and their variational regularities are not obvious. Therefore, it is difficult for conventional methods, such as variance analysis, data fitting, etc., to analyze accurately the complex experiment data.Pattern recognition can easily classify information, even if there are many influencing factors. For pattern recognition, there are some sub-disciplines such as discriminant analysis, feature extraction, error estimation, cluster analysis (together sometimes called statistical pattern recognition), grammatical inference, parsing and matching (sometimes called syntactical and structural pattern recognition) [1, 2]."

Jan 1, 2012

By Daniel C. McLean

Extraction data for Cu, Zn and Fe were obtained from 4.5" and 10" columns using massive sulfide ore and natural acid mine water. The purpose was to determine if recycling of solution through the column would produce leach liquors of 4 g/l Cu and Zn at extraction rates of 1 g/l per pass at typical flow rates of 0.002 to 0.006 gpm/sq.ft. Test results exceeded expectations. Cu and Zn concentrations of 4 g/l were obtrained within 4 to 6 cycles. Concentrations greater than 6 g/l Cu and 8 g/l Zn were reached within 10 cycles. Concentrations of greater than 40 g/l of Fe and free sulfuric acid were obtained with no decrease in biological activity being observed. No reagents were used.

Jan 1, 1995

By D. T. Smith, L. M. Hsiung, J. J. Schmitt, J. W. Golz, R. L. Lankey, H. N. G. Wadley, J. Z. Zhang, B. L. Halpern

"The microstructure and mechanical properties of Al/AI2O 3 metal-oxide nanolaminates fabricated by' a novel Jet Vapor Deposition (JVD) process at substrate temperatures of ~25° and -250°C have been investigated using transmission electron microscopy (TEM) and nanoindentation methods. The thickness of the oxide layer was held constant between 2 and 5 nm, whilst the Al layer thickness was systematically varied from -3 to -50 nm. Continuity of the Al layers was significantly improved when the nanolaminates were deposited at an elevated substrate temperature (-250°C). The yield strength of the nanolamintes with Al layers greater than -25 nm follows a Hall-Petch type relationship, whereas that of the nanolaminates with Al layers less than -25 nm is better predicted by a Koehler-Lehoczky strengthening model. IntroductionAluminum-aluminum oxide (presumably A12O3) nanolaminates have been recently fabricated using a novel Jet Vapor Deposition (ND) process developed and patented by Jet Process Corporation [1-4]. ND uses sonic, high purity helium (He) gas jets to entrain atomically dispersed vapor and deposit films. It is of interest here because it can deposit multilayered structures (laminates) inexpensively at high rates. Materials with a thin, multilayer structure are of interest because they potentially offer novel mechanical and physical properties [5]. Koehler in 1970 used an image force model to investigate the strength of laminated materials and proposed the use of alternating layers of high and low shear modulus metals to produce high strength composite materials [6]. He predicted that dislocations would have to overcome a large repulsive image force in order to move from metal layer B of lower shear modulus (uB) into metal layer A of higher shear modulus (uA)' The image force (F) is given by the relation:"

Jan 1, 1994

By Jean-Pierre Birat, Ana-Maria Iosif, Denis Ablitzer, Olivier Mirgaux

"Integrating environmental considerations into the product traditional process design is now the major challenge for steel industry. Life Cycle Assessment (LCA) is nowadays considered as an appropriate method for assessing environmental impact and selecting new technologies to reduce CO2 emissions for steel industry.In this paper we propose a new methodological concept which combines LCA thinking with process simulation software in order to carry out the life cycle inventory of classical steelmaking process.Using Aspen PlusTM software, a physicochemical model has been developed for the integrated steelmaking route. This model gives the possibility to carry out life cycle inventories for different operational practices in order to optimise the use of energy, to calculate CO2 and other emissions and to control the mass and the heat balances of processes.It is also shown that such approach can be used to design and assess new technologies for steelmaking without large industrial application.IntroductionDuring recent years, it was recognised that CO2 emissions are the major factor of the global warming effect. In order to meet Kyoto requirements, the steel industry is embracing the challenge of sustainable development by improving its competitiveness and economic success while reducing its environmental impacts. Integrating environmental considerations into the traditional product design process, for powerful eco-efficiency, is now one of the major priorities for steelmakers.The European Steel Industry has measured up to this challenge by creating ULCOS (Ultra Low CO2 Steelmaking) consortium that has taken up the mission to develop breakthrough steelmaking process with the potential to reduce CO2 emissions (Eurofer, 2005). In order to develop technologies to reduce emissions, it is necessary to assess the environmental impact of the classical steelmaking route (coke plant, sinter plant, blast furnace, basic oxygen furnace, continuous casting and hot rolling)."

Jan 1, 2009

By R. E. Fanning

"IntroductionThe Aluminum industry is one of many materials industries which strive to make their material the preferred choice for large volume products. In some applications one material has a natural advantage over others, but more frequently several materials compete with one another, each providing one or more advantages and some trade-offs. Customers may design their product with several objectives such as minimum system cost, maximum customer appeal or maximum manufacturing flexibility, choosing materials which best combine cost and performance. In such markets it may become necessary for a material supplier to enhance the attractive features of the particular material to outweigh its disadvantages.It is difficult, if not impossible, to predict how various materials will evolve. Technological breakthrough, government regulations, material availability or sociological issues may redefine the balance between competing materials. In spite of some uncertainty regarding the competitive position of competing materials, there is little doubt that unrelenting pursuit of product quality improvement and cost reduction are essential to future viability of the aluminum industry. It is the intent of this paper to identify some areas where technological improvement would be beneficial. Thus this paper is a collection of briefly described problems that will hopefully stimulate the thoughts and research required for knowledge based solutions. Rolling ProcessA particular example is the beverage can industry where aluminum, steel, glass and plastics vie for a share of the m.arket. The high cost of aluminum relative to steel or glass requires minimizing the amount of metal per can. The high intrinsic value of aluminum has led to extensive recycling of cans although net metal cost is still higher than that of the competing materials. Intensive engineering of the beverage can led to improved design and better understanding of material requirements. These improvements permitted substantial reduction in sheet thickness over the past decade. The downward trend in metal thickness for beverage can sheet is shown in Figure 1."

Jan 1, 1988

By C. S. Simons

This paper presents a review of the extractive processes used in the production of nickel, with emphasis on developments since the beginning of the Second World War. Attention is given to the factors, many outside the nickel industry itself, which determined the direction of process research and strongly influenced the ultimate commitments to industrialize the resulting developments. An example of such a factor is the sudden surge in demand, far exceeding the then available nickel production capacity, that was caused by the advent of World War II; the result was the first serious consideration ever given to low- grade laterites as a viable source of primary nickel. Other factors discussed include such items as process development in the extraction of other metals - particularly copper; the availability of increasingly sophisticated materials of const- ruction; the advent of the "environmentalist" and related political developments; the massive escalation in the price of energy - particularly oil. The paper concludes with an attempt to forecast the nature of the most effective nickel process of the future, based on extrapolation from the economic and political situation that exists today.

Jan 1, 1988