Search Documents

By Patricio Barrios

In February 1996, ATLANTIC, COPPER completed the construction of a Project for Expansion and Environmental Improvements in its Smelter and Electrolytic Refinery located in Huelva. Following the expansion, the new operating concept is based on the simultaneous blowing of two converters, while increasing throughput in the Flash Furnace up to the level required to deliver matte to both converters. While the production level planned with the Project.(270,000 MTPY of copper from concentrates) was reached the following June, work since then has been carried out to optimize the new equipment .and to develop a new operating shedule. This paper describes operational experiences from the start up of the Expansion Project, difficulties encountered and operating improvements introduced, which have allow an increase of production levels up to 300,000 MTPY of copper.

Jan 1, 1998

By R. Rajiv Srivastava

Brine leaching of a TSL processed zinc-plant residue (ZPR), containing 83.3% anglesite, has been investigated for lead recovery. A prior treatment of ZPR in acid solution did not show any significant effect of acid concentration in zinc dissolution. The study reveals that the solubility limits of PbCl2 is as an important factor with respect to the brine concentration and pulp density in lixiviant. The dissociated sulfate ions hinder the formation of PbCl2 on prolong leaching (above 60 min), while exhibiting the reverse solubility of lead as PbSO4. A 3-step leaching process could yield >92% leaching efficiency when the parameters were maintained as: 10% pulp density in a 250 g/L NaCl solution, 80 °C temperature, and 60 min time. This leaves the insoluble ferrite, sulfides and oxy-sulfates of zinc and lead in the final residue as revealed by the XRD characterization.

By Dan Michaelsen, Warwick Stewart

"PT Kaltim Prima Coal (KPC) is a large-scale truck and shovel operation mining thermal-coal in East Kalimantan, Indonesia. The operation produces 15 million tonnes of coal and mines over 120 million bank cubic metres of overburden annually. Approximately 35 percent of the waste rock is classified as potentially acid forming. Acid drainage must therefore be managed to prevent acid formation from spoil dumps and mined-out areas.KPC aims to prevent acid production in dumps by covering potentially acid forming spoils with materials identified as non acid-forming. The covers, built to engineering standards, minimise the flux of oxygen and water to pyritic spoils, thereby controlling the oxidation reaction, and reducing ARD discharge to negligible rates. Cover designs and cover materials vary according to stability, materials availability, equipment availability, and cost effectiveness. A modified field net acid generation (NAG) test procedure has been developed at KPC to identify and segregate overburden geochemical types. This paper discusses the ARD management strategies and operational procedures adopted by KPC to manage potentially acid forming waste rock. The development and field application of the NAG procedure at KPC is presented in a companion paper. Analytical"

Jan 1, 1999

By Pekka Hanniala

The Outokumpu Flash Smelting process today is the most feasible method for copper matte smelting. The economic feasibility of the process has always been one of the main decision making criteria in smelter projects. Thus, today about 50 % of the world primary copper production utilizes Outokumpu Flash Smelting Technology. However, in the future, environmental criteria will have stronger and stronger impact on decision making. Flash Smelting technology offers the best pollution control features of any process. today. It is foreseen that, in the near future, the global trend will be that all the smelters must decrease their emissions at an accelerating rate, compelling the smelters to make increasingly larger investments on environmental protection. In most of smelters ?today, Peirce-Smith converting and transfer of the molten material in ladles are the number one pollution source. The key today for copper converting and minimizing emissions is the Kennecott-Outokumpu Flash Converting process, which has proven to be the most effective converting method in terms of pollution control and, production efficiency including capital and operational costs. Outokumpu Flash Smelting technology is applicable also for small to medium scale smelters but the most interesting area is the upper capacity limit for smelting in one line, which has not yet been reached. We predict that by the year 2000 to 2005, there will be at least one smelter which produces 500,000 tonnes of Cu per year based on one Flash Smelting and Flash. Converting unit. The current state-of-the-art of the Outokumpu Flash Smelting - Flash Converting process is presented in this paper as well as some new options for copper production to be utilized in the near future but which are available already today.

Jan 1, 1998

By F. Michael Hosking

Modeling of a furnace brazing process is described. The computational tools predict the thermal response of loaded hardware in a hydrogen brazing furnace to programmed furnace profiles. Experiments were conducted to validate the model and resolve computational uncertainties. The results from selected furnace simulations and measured thermal events were compared. Critical boundary conditions that affect materials and processing response to the furnace environment were determined. "Global" and local issues (i.e., at the furnace/hardware and joint levels, respectively) are discussed. The ability to accurately simulate and control furnace conditions is examined.

Jan 1, 1998

By Jean-François Boulanger

The production of rare earth elements from ore usually consists of three steps; the separation of a concentrate of REE bearing minerals; the cracking of the REE minerals to liberate the REE into an aqueous solution and separation of REE into individual elements. This paper describes the results of laboratory tests conducted on a carbonate-rich REE ore containing bastnaesite and monazite. The tests cover the whole processing sequence of beneficiation, preparation of the REE solution using a caustic leach followed by acid leach to break monazite and bastnaesite and liberate REE into an aqueous solution and the partial separation of the REE using solvent extraction. Details on the product quality and process performances (recovery and impurities removal) are given for each studied step. The paper also discusses the economic advantage of separating the REE rather than producing a mixed REO product to be sold to a refinery for REE separation. A mini-pilot plant version of the process is currently planned.

By Renato G. Bautista

The solvent extraction separation of nickel, cobalt and their associated metals have been considered for industrial application since the early 1960's. This review of the solvent extraction processes is limited to the industrial applications, pilot plant and the more extensive bench scale studies reported in the literature. The processes with their significant chemical and technological contributions are discussed in detail whenever the information are available. The application of solvent extraction to the nickel-cobalt processing has so far been limited to the secondary separation of nickel-cobalt containing feedstocks derived from other primary nickel-cobalt separation methods.

Jan 1, 1993

By Yuzhe Zhang, Matthew Andriese, Jiann-Yang Hwang, Guanghui Li, Zhiwei Peng, Tao Jiang

The microwave power absorption characteristics of iron oxides, including Fe2O3, Fe3O4 and Fe0.925O, have been studied by determining dielectric loss and magnetic loss distributions in 0.05-m-thick oxide slabs irradiated with 1.2-kW, 2.45-GHz microwaves. The results reveal that the dielectric loss is the main factor contributing to microwave absorption in Fe2O3 and Fe0.925O, while the magnetic loss dominates the power absorption in Fe3O4 below its Curie point. Uneven power distributions are observed in the slabs and this phenomenon becomes even worse at high temperatures at which the permittivity increases significantly. Quantification of power absorption in the oxides is of great importance for efficient and uniform microwave heating

Jan 1, 2015

By David G. C. Robertson

A new approach is described for the calculation of the kinetics of metal/slag, metal/slag/gas, and metal/matte/slag/gas reactions. The algorithm assumes that equilibrium is achieved at the interface between phases, and uses an equilibrium solver (such as SOLGASMIX) to compute the equilibrium state at the interface at each time step during the reaction. For multiple phase systems a number of unit operations, representing the different phases and interfaces, must be connected together in a reasonalbly complex manner, and the METSIM software package has been utilized for this purpose. The new approach is superior to the SMAK software developed by the author and his co-workers over the past decade, for the reasons discussed in this paper.

Jan 1, 1995

By C. J. Beyke

In recent years recycling of household batteries has received increasing attention, primarily for environmental reasons. This article reviews the major battery types and some of the technologies available to recycle them. It also discusses issues such as collection and sorting which are related to battery recycling in the United States. Finally, results from research being conducted by the U.S. Bureau of Mines on the reclamation of nickel-metal hydride, alkaline, and zinc-carbon batteries are presented.

Jan 1, 1995

By N. A. Barcza

DC plasma-arc technology using a hollow graphite electrode (cathode) has been successfully implemented in the primary metallurgical industry in South Africa up to the 30 MW scale. Mintek has applied its expertise base, established over the past fifteen years, to testing the treatment of metallurgical wastes such as carbon- and stainless-steel plant dusts, lead- and zinc-containing slags, and residues from the base-metal industry. Favourable results have been achieved, and disposable products were produced. The evaluation of numerous wastes indicates that recovery of zinc as metal gives the best economic return from these sources. Direct recovery via a splash condenser or electrolytic zinc extraction from fume are the two preferred alternatives under review. In both instances dehalogenation is an important issue, but can be achieved by suitable treatment processes. The Enviroplas technology provides a flexible, commercially viable approach to the treatment of a wide variety of wastes. Mintek, together with its associate Pyromet CC, are installing a plasma- arc pilot-plant facility with both an ISP lead-splash condenser of about 5 t/d condensed zinc capacity and a combustion chamber to burn zinc vapour to zinc oxide. This will demonstrate the suitability of the Enviroplas technology for treating specific metallurgical wastes, so that customized industrial plants can be engineered based on large-scale testwork.

Jan 1, 1994

By Timothy W. Skszek, Adrian S. Sabau, Hebi Yin, Xiaoping Niu

The microstructure evolution during solution treatment plays an important role in mechanical properties of heat-treated aluminum alloys. In this paper, models were reviewed that can predict the microstructure evolution during the solutionizing process of the aging heat treatment of aluminum alloys. The dissolution ofMg2Si particles has been modeled as a diffusion process of Mg in the a-Al matrix. The evolution of volumetric fraction of fragmented silicon as a function of time and temperature was also considered. The growth and coarsening of silicon particles during the heat treatment was considered. It was found that constitutive equations and required property data for most of the phenomena that need to be considered are available. Several model parameters that need to be obtained from material characterization were identified. Pending the availability of these model parameters, this comprehensive model can be used to describe the microstructure evolution of aluminum alloys in order to optimize the solutionizing heat treatment for energy savings.

Jan 1, 2013

By Vinay Kumar

The disposal of large quantities of electronic scraps generated world wide is causing not only environmental problem but also loss of resources. Therefore, R & D efforts have been made to develop a suitable process for extraction and separation of metals viz. copper, zinc, cadmium and nickel expected from the leaching of e-scraps using solvent extraction process. Different process parameters viz. pH, aqueous to organic ratio, kinetics of extraction, extraction isotherm to establish stage requirement for extraction in continuous mode etc have been studied to optimise the condition for the separation of metals. The studies showed the selective extraction of copper after iron precipitation from the sulfuric acid leach solution of e- wastes containing ~1.0 g/L Cu and minor impurities with 2-hydroxy-5- nonylacetophenoneoxime (LIX 84) above pH 2.0 in single stage. A scheme for separation of cadmium, zinc and nickel has been proposed using di(2-ethylhexyl) phosphoric acid (D2EHPA) under controlled pH of the aqueous solution. The order of extraction was found to be Zn> Cd> Ni.

Jan 1, 2009

By Steven R. Pittman, Colin McCullough, Peter Galuska

"Traditionally Continuous Fiber Aluminum Matrix Composites have been fabricated using high strength fibers and high strength matrices, often commercial alloys, with the goal of producing high strength composites. However the specific role of the choice of matrix alloy on composite properties has not been well established. One way to control composite tensile strength is to use coatings to introduce a low strength interface between fiber and matrix which tends to reduce the importance of the matrix selection, but unfortunately renders the transverse strength unacceptably low. Thus using a system with strong bonding between fiber and matrix is desirable, such as an alumina fiber / aluminum alloy matrix system. In this case the transverse strength is a strong function of the matrix strength. However the longitudinal strength then depends largely on the characteristics of the matrix. The important role of the matrix is discussed using examples of alumina fibers in various aluminum alloy matrices. The key attributes are matrix constituent phases, alloy chemistry, alloy reactivity with the fiber, and matrix strength. From the understanding developed in these systems a set of design rules may be established for selecting an optimum matrix. IntroductionAluminum matrix composites (AMC's) reinforced with continuous fibers offer very attractive property gains over AI alloys, such as strength, stiffness, and fatigue resistance. These gains are magnified when specific mechanical properties are compared which make them attractive candidates for replacing steel, nickel, titanium and aluminum alloy parts in weight critical applications (1). Many systems have been tried in the past; B/AI, C/AI, SiC/AI, Si-Ti-C-O/AI and AI203/AI. Technically B/AI was a very good system but was expensive in regard to both fiber cost and fabrication and SiC/AI and C/AI systems are still plagued with reactivity problems. The Si-Ti-C-O/AI appears to be a good strength system but with lower stiffness. Until recently, the AI203/AI was a low strength system, in part due to a lack of a high strength fiber. Recently 3M introduced a high strength AI203 fiber - Nextel™ 610, which leads to high strength composites (1,2) and may also be both low cost and also compatible with less expensive casting approaches for fabrication."

Jan 1, 1996

By William Gregg

Recent environmental and workplace safety legislation has Imposed more stringent limits on the amount and type of particulate emitted Into the air. In the past, the mass of particles contained In a volume of air was the governing criteria. Now the size and precise chemical nature of the particulate must be known and controlled In addition to it's ?mass. Processors of metallic materials have to implement stricter control practices and more efficient control equipment to meet the new regulations. Pulse-Jet dust collector systems are being used to control particulate emissions from various process gas streams. Pulse-jets :are also being used for maintaining a healthy environment In the workplace. this paper will discuss the impact of these regulations, the control techniques used to comply with such regulations, and the equipment needed for compliance.

Jan 1, 1992

By James R. Craig

The General Image Processing System (GIPSY) is being employed for the quantitative textural analysis of complex sulfide ores from the Southern and Central Appalachians and for the determination of liberation characteristics of the mineral constituents during grinding. Optical images from a microscope-mounted TV camera or from 35mm film are converted into digital images which are subsequently analyzed by GIPSY, a transportable image processing software package. Properties measured by GIPSY include spatial distribution of mineral constituents, grain sizes, grain shapes, grain orientation and mineral co-occurrences.

Jan 1, 1982

By Hideo Nakae, Hideki Yamaura, Toshiaki Kimura

"In 1968 J. N. Reding et al. suggested processes for fabricating composites. According to their patent, decompression atmosphere, which occurs during the reaction between magnesium and oxygen and/or nitrogen in the closed system, causes the spontaneous infiltration of melt into narrow spaces such as ceramic preforms. However, they did not report the proof of this phenomenon or the industrial manufacturing method. Therefore, this research measured the pressure change among SiC particles surrounding molten aluminum. As a result, the pressure reduction during the Mg reaction was identified. Moreover, the existence of Mg3N2, which improves the wettability between Al alloy melt and SiC particles on the interface, was observed on the surface of particles. Applying these two phenomena, a new process for the manufacturing of cast discontinuously reinforced aluminum composites (DRA) was developed. This new method is expected to produce DRA without additional pressure.IntroductionWith the increasing demands for light-weight materials in the automotive and aerospace industry in recent years, ceramic particulate reinforced aluminum matrix composites called DRA (Discontinuously Reinforced Aluminum Composite) have been receiving significant attention because of its lightness, superior abrasion resistance, high heat conductivity and low thermal expansion [1-3]. Consequently, DRA was considered for electronic parts such as heat-sinks or a base for power semiconductors, and began to be applied for automotive parts including brake drums, discs, cylinder liners, pistons and so on [4- 6]. However, high machining cost is one of the significant barriers to widespread use ofDRA. One solution to this problem is the adoption of cast DRA that can be produce to near-net shape, reducing machining cost."

Jan 1, 2000

By E. Dendy Sloan

An overview of hydrate properties is given, with emphasis on unusual deviations from ice, the most common solid water form. Reliable sample preparation and reproduction of in situ hydrates provide the foundation for all hydrate science and engineering. Relations are given to connect the three domains in the title: (1) micro-scopic properties measured with Raman, NMR, and diffraction spectroscopy, (2) meso-scopic properties measured with single crystals, and (3) macro-scopic properties measured with pressures, temperatures, volumes, etc. A principal illustration relates micro-scopic and macro-scopic domains. Experiments provides the basis for improving statistical thermodynamics model for these compounds. To date, this model is one of the most commonly used industrial statistical thermodynamics applications, based upon the classical model of van der Waals and Platteeuw (1959). Microscopic measurements and simulations indicate model assumption improvements, resulting in the next generation of the statistical thermodynamics for improved macroscopic property prediction.

Jan 1, 2002

By Caisa Samuelsson, Taishi Matsushita, Hannes Holmgren, Sina Mostaghel

"Rönnskär Smelter of Boliden Mineral AB, Sweden, is a large end-processor of secondary raw materials and waste, including electronic scrap. Electronic scrap may introduce various impurities to the smelter's flow-sheet, among which alumina is a common and significant one. This article summarizes the results of an ongoing research at Luleä University of Technology, Sweden, to study the influences of alumina on different properties of slag from the zinc fuming process at Rönnskär smelter. A combination of different experimental techniques and thermodynamic calculations have been used to investigate properties such as density, surface tension, effective thermal diffusivity, viscosity, and melting/leaching behaviors. Results show that the addition of alumina to this slag increases the degree of polymerization of the melt, and physical properties vary correspondingly. Mineralogy of the semi-rapidly solidified samples is also changed due to alumina addition. A correlation between mineralogy and leaching behavior can be observed.IntroductionBoliden's Rönnskär Smelter is a base- and precious-metals producer located in north of Sweden. Its main products are copper, zinc clinker, lead, gold, and silver. Sulphuric acid, liquid sulphuric dioxide and iron sand (granulated slag) are some of its main by-products. In order to optimize the overall outcome of the process, different refining units are integrated in the smelter's flow-sheet (Figure 1). Copper concentrates and fluxing materials (mainly silica sand) are charged to the process. The produced matte is sent to the converter and the generated slag is charged to the fuming furnace, where it is treated by reducing gases to produce zinc clinker. The converter's slag is charged to the electric furnace, while the fumed slag is tapped into the settling furnace for further cleaning, where matte, slag and speiss (residual metals) are separated. The matte from the settling furnace is also sent to the converters; its speiss is sold to external customers; and its slag is water granulated and sold as construction material, which is known as iron sand."

Jan 1, 2012

By Joerg Hammerschmidt, Marcus Runkel, Andreas Wirtz, Kent Pope

"Fluidized bed reactor systems in the minerals industry have been progressively developed and widely implemented over a period of more than sixty years for a multitude of process applications. Their versatility is manifested in calcining, roasting and combustion treatment of minerals including solid fuels. Experiences from metallurgical processes have expanded to new applications in the oil shale processing, biomass combustion and renewable energy sector. This paper focuses on the most important aspects of fluidized bed technology for a variety of Outotec processes. Energy recovery is a major topic for all applications and will be addressed, as well as environmental aspects, particularly regarding the off-gas treatment. Outotec is one of the pioneers of roasting and the fluidized bed process including gas cleaning and sulphuric acid production where applicable. Process development is strongly supported by significant investment in R&D, thus enabling process adaptation and scale-up to meet specific customer/market requirements.Introduction to Fluidized Bed TechnologyThe early days of fluidized bed technology were characterized by the use of bubbling fluidized bed reactors (BFB). This technology was popular for roasting zinc and copper ores. The introduction of circulating fluidized bed technology led to increased plant capacities and improved process control for the traditional processes. Furthermore, the technology has been applied in many other industries, including the renewable energy industry, which will be part of this design and process comparison. The paper starts out with the fundamentals on particle fluidization as the main common design parameter, leading to the importance of heat recovery and offgas treatment.In fluidized reactor systems, the particle concentrations can reach several hundred kilograms per cubic meter of fluidization gas. This high solid concentration leads to large surface areas and enables direct contact of gas molecules with particle surface molecules. Excellent conditions for enhanced heat and mass transfer thus provide nearly ""ideal"" heat exchange conditions and better reaction kinetics. The bubbling bed exhibits a better heat transfer coefficient within the bed in comparison to the circulating fluidized bed (CFB). The different conditions of gas velocities and solid concentrations allowing the classification of fluidization reaction regimes are shown in the Reh diagram in Figure 1."

Jan 1, 2014