Search Documents

By Y. F. Liang

Fe-6.5wt.%Si alloy has excellent soft magnetic properties compared with conventional silicon steel. It is very brittle at room temperature due to appearance of ordered phases, like B2 and DO3. In this paper, we investigate the effect of ordering on cold workability of this alloy. Methods of rapid quenching and hot rolling were utilized. It is found that rapid quenching and proper heat treatment of the hot rolled sheet could decrease the degree of order due to the very high solidification rate and high cooling rate. The rapid quenched sheet and hot rolled sheet after proper heat treatment could be cold rolled without crack. Microstructure, phase ordering, micro hardness, and cold rolling properties were investigated by Optical Microscope, X-ray Diffraction, Micro Hardness Indenter and Four-high Mill.

Jan 1, 2009

By M. Pakala, Z. Fan, Ray Y. Lin

Deposition of hard chromium coatings using electrodeposition is accompanied by emission of hexavalent chromium mists which is a carcinogenic. Hence alternative chromium deposition technologies are being investigated. Sputter deposition is a strong candidate to economically deposit hard chromium coatings in an environmentally friendly way. Chromium coatings of 2-3 µ m thickness were deposited on plain carbon steel coupons using RF magnetron sputter deposition. Depositions were carried out with 0 to 22 vol% nitrogen in the plasma. Structure of the coatings was studied using x-ray diffraction analysis With increasing nitrogen contents, formation of the two nitride phases was observed. The pure chromium phase was detected in coatings with up to 7% nitrogen in the sputtering gas. The solid solution of nitrogen in the pure Cr phase coating was identified by shifts of Cr x-ray diffraction peaks to higher d-spacing. The microhardness of the coatings deposited at a substrate temperature of 200°C showed an increase in hardness with increasing nitrogen content from 600 kgf/mm2 (5.9 GPa) at 0% nitrogen to I250 kgf/mm2 (I2.25 GPa) at 9.5 % nitrogen and a subsequent decrease in hardness to I 100 kgf/mm2 (11 GPa) beyond 9.5 % nitrogen in the sputtering gas. This corresponds to the formation of the hard Cr2N phase, at 9.5 % nitrogen, and CrN phase, at I5.7 % nitrogen. The reported bulk hardness values of Cr2N and CrN are I600 kgf/mm2 (I5.7 GPa) and I 100 kgf/mm2 (11 GPa) respectively. For pure Cr phase coatings, there is a slight increase in hardness for coatings deposited at 7. I % nitrogen from that without nitrogen in the sputtering gas. This could possibly result from the solid solution strengthening of the Cr lattice by nitrogen. For films deposited at 200°C, phases of the deposited films seem to be the overwhelming factor in controlling the microhardness.

Jan 1, 1998

By Melvin H. Miles

"Considerable research has been conducted on the anodic oxidation of methanol in fuel cells. The electrochemical reduction of carbon dioxide in aqueous solutions to form methanol is the same reaction in reverse, i.e. CO2 + 6 H+ + 6 e- ? CH3OH + H2O. The same catalysts and conditions may operate for both reaction directions. This carbon dioxide reduction reaction, however, must be able to compete with the electrochemical reduction of water to form hydrogen gas. Thermodynamically, the reduction of CO2 to form CH3OH is slightly more favorable than the reduction of water. The use of nearly neutral electrolytes rather than acidic electrolytes makes the reduction of CO2 kinetically more favorable. The thermodynamics of various reaction steps are presented. Similarities exist with the electrochemical reduction of CO2 and the green-plant photosynthesis process that converts CO2 to carbohydrates.IntroductionVirtually all of the oxygen in the earth’s atmosphere is of biological origin having been generated by green-plant photosynthesis from water and carbon dioxide [1]. The net reaction can be represented byCO2 + H2O ? O2 + [CH2O] (carbohydrates, etc.) (1)Chlorophyll and enzymes promote this reaction, and the energy required comes from sunlight. The actual photosynthesis process is a complex multistage reaction and requires 469 kJ mol-1 of energy supplied by the sun. Isotope tracer experiments using 18O have shown that both the oxygen atoms in the O2 molecule originate from H2O, whereas oxygen atoms in the carbohydrates come from CO2 [1]. The total amount of water on the earth is split by photosynthesis and reconstituted by respiration and combustion once every 2 million years or so. The photosynthetically generated oxygen gas temporarily enters the atmosphere and is recycled about once every 2000 years [1]. The carbon dioxide is partly recycled in the atmosphere and oceans after an average residence time of 300 years and is partly fixed by precipitation of CaCO3 and other carbonate minerals [1]."

Jan 1, 2008

By Metehan Erdogan, Ishak Karakaya, Fuat Erden

"Mg-Ni system draws attention due to the promising hydrogen storage properties of Mg2Ni. The proposed method involves the use of NiO and MgCl2 in an electrochemical cell to from Mg-Ni intermetallics directly. The electrodeoxidation of NiO was followed by combination of Mg and Ni in molten salt electrolytes. The products were characterized by XRD analysis and SEM examinations. The quantitative results from Rigaku supported by Rietveld Refinement method conducted by Maud showed that more than 50 percent of the input Ni was converted to Mg-Ni intermetallics.INTRODUCTIONIt is well known that fossil fuels are the most common energy producing materials throughout the last century although, they are not renewable and their usage cause critical environmental problems [1, 2]. Hydrogen, on the other hand, is known as a clean, renewable energy carrier and instead of fossil fuels; usage of hydrogen for energy production will be the benefit of mankind. However, there are problems that hinder more common usage of hydrogen such as hydrogen storage [3]. Mg2Ni is known as Mg based hydrogen storage material with high hydrogen storage capacity [3-6]. Common Mg2Ni production methods are; mechanical alloying [8-11], vacuum induction melting [12, 13], vacuum arc melting [14], combustion synthesis [15], melt spinning [16], repetitive rolling [17] and isothermal evaporation casting [18] were also used. However, in all of these, pure Mg and Ni are required to be produced previously. Therefore, difficulties arise during handling, preparation and combination of Mg and Ni due to highly reactive nature of especially magnesium (i.e. oxidation of Mg) [11, 17, 19, 20]. Although hydrogen desorption dynamics can be significantly improved with usage of nanostructured Mg2Ni [7], it is difficult and it requires very long processing durations to produce nanostructured Mg2Ni by above processes."

Jan 1, 2014

By G. Sterzik, W. A. Jankola, T. L. Salway, D. J. McKay

At Trail, British Columbia, Cominco's zinc leaching and solution purification processes include direct pressure leaching of zinc concentrates, leaching of fume from the lead smelter, leaching of calcine and electrolyte purification. These processes have been adapted to match the unique characteristics of Cominco's integrated zinc and lead operations. Recent modifications include changes to the purification process and iron-residue handling circuits. In 1997, a new five-compartment autoclave, complete with ancillary equipment, was installed in the pressure leaching plant. This paper discusses these changes, the current flowsheet and further improvements.

Jan 1, 2000

By M. Bilal Khan

Thermal stress relief by means of a typical heat treatment cycle (660oC for one hr) is compared with the one achieved through vibratory stress relief at resonant and multiple resonant frequencies for the D-406 HSLA material. Our analysis of the data is based on the microhardness profiles measured for the entire length of scales, namely, base metal, heat affected zone (HAZ) and the weld bead itself. The profiles obtained using the two techniques mimic each other, for an equivalent 70% stress relief level. The data are further qualified by impact testing wherein the zone of interest is projected in the retention groove to provide impact by the pendulum striker in the Charpy mode. Higher equivalent energy absorption in the treated specimens confirms the efficacy of the vibratory method. The present work rectifies earlier anomaly where heat treatment has been reported at 310oC for the same material.

Jan 1, 2009

By A. Vahed

The Goro Nickel Project is situated in the Southern Province of New Caledonia. Inco Limited and Goro Nickel S.A. have developed a process that features the use of pyrohydrolysis to produce nickel oxide. The process treats a blend of laterites by Pressure Acid Leaching followed by solvent extraction of nickel and cobalt using Cyanex 301®. Purified nickel chloride solution is converted to high purity NiO product and 6M hydrochloric acid, which is recycled back to the SX circuit. In co-operation with Andritz AG, spray roaster and fluid-bed pyrohydrolysis technologies were examined for this purpose. Tests were conducted at the Andritz AG pilot plant in Vienna, Austria, and at Goro in larger scale installations. The latter served to establish process engineering design parameters for scale-up. Several process variables were investigated in both technologies and the off-gas characteristics were established. Fluid-bed pyrohydrolysis was selected for the Goro commercial plant, primarily because it produced a granular nickel oxide. The main focus of this paper is to outline the results obtained in pilot plant studies of liquid fueled fluid bed pyrohydrolysis for the Goro Project. Keywords: lnco Goro Nickel, Fluid Bed Pyrohydrolysis, Pilot Plant Tests

Jan 1, 2004

By Frame Ritzert, Dennis Keller, Vijay Vasudevan, David Arenas

"An investigation was conducted to describe topologically close packed (TCP) phase instability as' a function of composition in the advanced ·Ni-base superalloy Rene N6. TCP phases are detrimental to overfill high-temperature performance of Ni-base superalloys because of their brittle nature and because they deplete the Ni-rich matrix of potent solid solution strengthening elements. Thirty-four variations of polycrystalline .Rene N6 determined from a design-of-experiments approach were cast and homogenized at 13 l5°C for 80 hours followed by exposure at 1093°C for 400 hours to promote TCP formation. The alloys had the following composition ranges in atomic percent: cobalt 10.61 to 16.73, Mo 0.32 to 1.34%, W 1.85 to 2.52%, Re 1.80 to 2.11%, Ta 2.36 to 3.02%, Al 11.90 to 14.75%, and Cr 3.57 to 6.23%. Physical and chemical characteristics of all microstructures obtained were described using various analytical techniques. From these observations, a mathematical description of TCP occurrence (s and P phase) was generated for polycrystalline Rene N6.IntroductionNi-base superalloy single crystals represent the state-of-the-art for turbine engine airfoil application as they offer the best balance of properties to allow for the high operating temperatures required: for efficient engine operation.1 Current trends in alloy design take advantage of improved creep rupture strength with the addition .of higher levels of refractory elements. 2 In .particular, the addition of significantly higher levels of Re in third generation superalloys is key for both microstructural stability and creep rupture strength. 3 While the presence of the refractories is thought to provide strength benefits from solid solution hardening, a tendency for alloy instability in the form of topologically-close-packed (TCP) phases or secondary reaction· zone (SRZ) ·phenomena accompanies the high refractory content. 3 The formation of these phases in sufficient amount is detrimental to the overall high temperature performance of Ni-base superalloys because of their brittle nature and because they deplete the Ni-rich matrix of potent solid solution strengthening elements.4 The tendency for a particular composition to form TCP may not be immediately known since the precipitation of TCP phases in Ni-base superalloys is nucleation controlled, thereby requiring long times at elevated temperatures to precipitate. 5 They preferentially nucleate along the octahedral planes of the Ni-base superalloys, usually in areas of refractory metal enrichment at grain boundaries or inside dendrites.5-6 In Rene N6, two closely related TCP phases, a and P, have been observed.2"

Jan 1, 1998

Equilibrium calculational software programs can be effectively utilized to illustrate the importance of activity or concentration, solubility, temperature, solution pH, solution potential, and ligand complexation to students studying hydrometallurgy. The calculational program STABCAL will be demonstrated. illustrative examples for the creation of diagrams such as EH-pH, activity or concentration-pH and activity or concentration-EH will be presented to demonstrate the fundamentals of real hydrometallurgical systems. Speciation, titration and mixing will be used to simulate or predict operational processes. Applications will include treatment of Acid Mine Drainage (Berkeley Pitlake water and sediments), mass balance potential/pH diagrams, leaching and selective separation of metals from electroplating sludge, metal adsorption at femhydrite surfaces, and flowsheet development for treating mercury sulfide K106 sludge.

Jan 1, 2002

By Carla Lupi, Alessandro Pescetelli

"Spent lead battery recycling still shows few weak points in the achievement of a 100% recycling of different waste matters and by- products arising from the recycling process. Some of said problems are dealing with aqueous streams outgoing the recycling plant, and more particularly, a) the waste waters discarded from the breaking and separation unit, b) purification of the spent electrolyte drained from waste batteries and upgrade to a quality compatible with full re-use by the batteries’ manufacturers, c) purification of the mother liquors discarded in the sodium sulfate crystallization process so to produce a salt of commercial grade. All of the above listed problems have been satisfactorily overcome applying an electrochemical process that, through different process conditions and parameters, is able to remove the harmful impurities that hinder the successful commercialization of such by products, or, at least, that can avoid heavy and expensive treatment plant and operation.IntroductionAlmost 100% of commercial lead and lead alloys produced by secondary lead plants is recycled to the new lead accumulators manufacture. The other by-products and residues produced through the lead recycling process may be classified into two groups:a) matters reusable in the new accumulators production processb) matters produced as a result of various reagents and additives used in the recycling process, to be sold to different market sectorsQuality and saleability of by-products are significant points for the economics of the secondary lead plant operation, because, if said by-products are not saleable, they are just wastes, so offsetting potential revenues, and, at the same time, adding a heavy burden to operating cost, like disposal cost [1]. When looking at a typical, modern lead scrap batteries recovery cycle, it is quite evident that we are still rather far from dealing with a waste-less technology (fig.1).The group a) includes 3 by-products produced through the breaking process: among those matters the polypropylene only usually reaches a standard quality suitable for sale to lead manufacturing sector or to other sectors as well. The other two by-products, electrolyte and separators, do not still reach, through a viable and effective regeneration process, a quality standard sufficient for their re-use in the lead batteries sector ."

Jan 1, 2008

By M. Cavallini, G. Cannavale, P. P. Milella, A. Pescetelli, C. Lupi

Ni-Cd sealed and vented cells have been widely used in the last few years. The environmental hazard related to the heavy metals contained in Ni-Cd batteries is well known. Therefore, a number of scientific studies and commercial processes have been implemented in order to recycle them. Since spent batteries are a heterogeneous and complex material, any kind of recovery process needs some preliminary treatments. The proposed process described in this paper has been tested in laboratory and further developed in a pilot plant. It consists of a combination of mechanical and hydrometallurgical treatment steps, and is able to treat all type of Ni-Cd batteries. In particular, the mechanical treatments have to be done separately on vented and sealed cells, while the hydrometallurgical step is performed on a mixture of the two products obtained from mechanical steps. A fully automated dismantling line would allow the separate recovery of the plastic or metallic casing, terminals, KOH electrolyte, and electrodes to be further processed· for Ni and Cd recovery. The electrodes coming from dismantling line and sealed batteries are submitted separately to an original crushing and elutriation treatment to separate metallic and active paste in the first case and metallic, plastic and active paste in the second case. The hydrometallurgical treatment is carried out on active paste bearing product to produce Ni, Cd, and Fe comn1ercial salts through acidic leaching followed by a multi-step solvent extraction operation to obtain pure solutions.

Jan 1, 2000

By Donghai Li, Cheng Pan, Xuewei Lv, Mei Liu, Enguang Guo

"Phosphorite is the main raw material for the production of phosphorus in chemical industry. More attentions have been drawn to the phosphorite concentrate beneficiated from low-grade phosphorite due to the decrease of high-grade phosphorite. For another, the agglomeration process is necessary for the phosphorite concentrate after beneficiation process. The mineralogy and sintering process of the phosphorite from Leshan, China were studied in this work. The result shows that the main phases in the phosphorite are fluorapatite (Ca3(P04)3F), hydroxylapatite (Cas(P04)3(0H)), quartz (Si02) and dolomite (CaMg(C03)2). The yield of the sinter increases with increasing the carbon dosage to 7%, and then decreases when it continuously increases. Similar regularities were found for the strength and the content of P20s of the sinter. The best strength of the sinter as well as its P205 content were discovered when the carbon dosage is 7%. Fluorapatite ((Ca5(P04)3)F) is the main phase in the sinter while fuggerite (Ca2MgSiz01) is the main binder phase.IntroductionPhosphorus is an important foundation industrial raw material of national defense industry, food industry and chemical industry, where it is used to produce red phosphorus, phosphonium hydroxide, phosphorus pentasulfide and phosphoric anhydride[l-2]."

Jan 1, 2013

By Vanessa M. Torres

Cia. Vale do Rio Doce is currently developing Niquel do Vermelho Project. The laterite deposit is located at Carajas Mineral Province at less than 15 km from Sossego Copper Project, scheduled for start-up in 2004. The available infrastructure, includes paved roads, large capacity railroad and port complex owned by CVRD, power supply and good quality water. The project was evaluated in the past for ferronickel production. In the late 1990s, CVRD switched its attention to investigating the usage of pressure acid leaching. The combination of good metallurgical behaviour for pressure acid leach (PAL) process route with reasonable mineable grades, and existing infrastructure justified the start of engineering studies in 2002. The project approach at the engineering phase is based on the dual objective of minimizing risks while maximizing project profitability and value. CVRD is currently completing the Niquel do Vermelho prefeasibility study. This paper outlines the main outcomes of the study and future perspectives for the project.

Jan 1, 2004

By Jian-hua Ren, Guang-liang Wu

A lot of dust is produced in iron and steel enterprises, giving rise to serious environment pollution, with which all countries are trying to find methods to deal. The influence of relevant technological factors on dephosphorization was investigated in laboratory, and the effect laws of that were analyzed. The results demonstrate that, in the given conditions of the best slag-metal proportion for hot metal dephosphorization is 1:10, and the optimum temperature is 1350 , The phosphorus distribution ratio of dephosphorization agent containing converter dust of 30% has the maximal value, with dephosphorization rate reaching 85%. Under the optimal conditions, premelting dephosphorization agent can significantly improve the ability of dephosphorization, dephosphorization efficiency increasing to 92%. Therefore, the dust can substitute the oxidant and fixative of dephosphorization agent, be used in hot metal dephosphorization, to enhance the efficiency of utilization.

Jan 1, 2016

By Robert D. Pehlke

"Current continuous casting processes are going through a rapid evolution of advances and new developments. At the same time, intense efforts are being directed to the development of radical new technologies such as continuous casting of thin slabs and strip steel.Traditionally, the casting processes for steel have been anticipated by the development and implementation of processes in the non-ferrous industry. This trend is reviewed and what it may portend for steel is described.IntroductionThe continuous casting of steel has been a widely adopted process in the production of steel. The concepts for this processing go back into the early and mid 1800's; however, commerical development was delayed for a variety of reasons until the mid twentieth century.Beginning in the early 1960's, adoption of continuous casting was initiated and continues at this point in time to be accelerated. In Japan, more than 90% of the steel produced is continuously cast (1). More than 50% of the steel produced in the United States is continuously cast and this fraction continues to rise (2). Numerous examples can be cited of installations costing well over $200,000,000 which have provided a payoff in less than a year and a half. As this process has continued to be applied and its technology to increase, computer control systems have been installed. In particular, in the larger plants producing slabs, sophisticated computer systems involving the integration and networking of mini-computers, micro-computers, and mainframe including back-up systems at all levels are being utilized. Pehlke (3), and Harabuchi and Pehlke (4) have described the structure of these systems."

Jan 1, 1988

By J. G. Zafiratos

The leaching of a Greek low-grade manganese dioxide ore, not amenable to conventional mineral processing operations, was studied using a mixed culture of Thiobacillus sp. bacteria. The experiments were carried out in specially designed continuously aerated and stirred tank reactors arranged in two-tank series. The first tank of each series was loaded with an elemental sulfur culture suspension while the second was loaded with a manganese ore high density slurry. The bacterial culture had been previously adapted to grow on elemental sulfur and also in the presence of manganese ore and dissolved manganous ion. A two level full factorial design was constructed in order to study the effects of the ferric ion concentration in the leach solution, the "elemental sulfu weight to ore weight" ratio, the ore pulp density and the composition of the dispersed gas. The responses which were investigated included percentage manganese recovery, co-dissolution of iron and manganese dissolution rate. Parameters with constant values throughout the experiments were the leach solution pH, the nutrient medium composition, the dilution rate and the ore and sulfur grain sizes. It was found that the ferric ion concentration was the most significant factor and had a positive effect on the final percentage extraction of manganese from the ore and also on the rate of manganese solubilization from the ore. The effects of the other factors studied are discussed in detail.

Jan 1, 1997

By N. D. Schupp

The Doe Run Company's Herculaneum, Missouri lead smelter has existed in continuous operation since 1892. Throughout the history of the plant extensive developments have been made to improve throughput, increase productivity, decrease operational costs and improve technology, while remaining an environmentally responsible producer of high quality primary lead in the international market. This paper provides an overview of the Herculaneum smelter, focusing on the most recent configuration of the operations. The paper includes discussion on all the aspects of primary lead production at the Herculaneum smelter.

Jan 1, 2000

By Raymond E. Healy

Circuit samples from the HBMS concentrator were assayed for l5elements, and image analysis was done to determine the modal quantities, grain size distributions and liberations of the minerals. Material balancing was done on these data to determine distributions of the minerals in each concentrator stream. The ore was mined during the waning phase of mining and is diluted with backfilled copper smelter slag. The mill feed grades 1.0 wt% Cu and 1.8 wt% Zn. The slag silicate phases contain approximately 1.5 wt% Cu and 6.5 wt% Zn; therefore the Cu and Zn head grades due to chalcopyrite and sphalerite, are only 0.9 wt% Cu and 1.2 wt% Zn, respectively. The recovery of Cu in the Cu-concentrate (Cu-conc.) is only 77.5 %, whereas that of chalcopyrite is 89.2 %. Similarly, the recovery of Zn in the Zn-concentrate (Zn-conc.) is only 40.2 %, whereas that of sphalerite is 71.0 %. The slag accounts for approximately 60 % of the Cu, and 85 % of the Zn in the tailings. The main loss of chalcopyrite is as unliberated grains to the tailings, and the main loss of sphalerite is as free grains to the Cu-concentrate and as unliberated grains to the Cu-concentrate and tailings. Approximately 85 % of the chalcopyrite and sphalerite lost to the tailings. accounting for 8 % and 10 % of the respective minerals in the concentrator feed, occur as middling and sub-middling grains. Extremely fine regrinding would be required to liberate these minerals.

Jan 1, 1989

By R. V. Kumar

"The use of sensors to monitor gaseous species in industrial processes is discussed. All of the existing systems have disadvantages. Sensors, based upon solid electrolytes, which can be placed directly into the gas stream are attractive but many also respond to oxygen, need to be sealed at high temperatures and require a separate reference. This paper describes sensors, usually based upon two electrolytes, which do not respond to oxygen and do not require high temperature gas seals or separate references. The application of these sensors to the measurement of carbon dioxide, sulphur dioxide and trioxide and hydrogen chloride is described. These sensors can be placed directly into the gas stream at elevated temperatures.IntroductionOn-line gas sensing is becoming more important as concerns regarding the environment mount. There are many established techniques for monitoring gases in industrial processes, with applications in safety monitoring, chemical analysis or process and emission control. Flue gas analysis involves the greatest technical complexity, requiring several sophisticated capital-intensive spectroscopic instruments for different species as well as needing highly skilled operators. There are also several instruments, based upon aqueous electrochemistry, which are available for the analysis of the gases S03, S02, N02 but these require that the gases are sampled at high temperature and cooled, prior to analysis. These instruments cannot be considered as giving on-line measurements of the gas composition. Furthermore, the power requirement of these instruments frequently precludes battery operation for field and domestic use."

Jan 1, 1997

By Renato G. Bautista

The chemistry of the separation of metals from each other and from the other undesirable components involve multiple simultaneous chemical reactions. In the case of leaching, the heterogeneous chemical reactions between the solid and the liquid phase may be limited to a few reactions. In the homogeneous liquid phase, the number of simultaneous chemical reactions could be double or triple that of the number of heterogeneous reactions:. The rate of dissolution becomes very dependent on the changing concentrations of the significant chemical species taking part in the multiple reactions in both the heterogenous and homogeneous phase. The rate expression developed for the process must take into account the mechanism of chemical reactions in order to best represent the actual process. This paper also examine the role of mass transfer with chemical reaction in the develpoment of the rate equations for dissolution, liquid-liquid extraction, membrane separation, precipitation, and electrodeposition.

Jan 1, 1996