Search Documents

By Jae-Chun Lee

Di-2-ethylhexyl phosphoric acid (D2EHPA) is widely used for separating rare-earth elements. In commercial plants, rare-earths are usually stripped from loaded extractant streams using mineral acid, then precipitated as oxalates. Many rare-earth uses demand specific powder characteristics, which are obtained by secondary processing. This paper demonstrates the feasibility of combining the stripping, precipitation and powder processing stages, thereby achieving considerable savings. MEHPA solutions were loaded with yttrium, then emulsified with oxalic acid-HC1 solutions to precipitate yttrium oxalate, which was readily calcined to yttrium oxide. The precipitation kinetics and yield were sensitive to process conditions. The morphology and size of the yttrium oxalate powders varied with the concentrations of D2EHPA and oxalic acid, and the presence of SPAN 60, which affected nucleation, growth, and the emulsion characteristics.

Jan 1, 1992

By Antonio Martin, Jesus Hurtado, Francisco Jimenez

"Atlantic Copper is one of the largest copper producers in Europe. Its production facilities, including a primary copper smelter and an electrolytic refinery, are located in Huelva, on the southwest coast of Spain. These installations enable the smelting of over 1 million tpy concentrates to produce up to 260,000 tons per year of cathodes and 900 ktpy of sulphuric acid.Since 1970, several improvements have been made at the Converters Area such as modifications of primary hoods, operations with an OPC system, installation of scrap chargers, the recent installation of the secondary hoods and other environmental projects. All these modifications have been aimed at increasing the capacity of our smelter while keeping our continuous environmental commitment.This paper describes the modifications and improvements carried out at the converters area and our proposals for future developments."

Jan 1, 2012

By Fumito Tanaka

The Converting Furnace (C-furnace) of the Mitsubishi process has solely provided opportunities for producing blister copper continuously from molten matte. Continuous converting originates from the proven technology for controlling the behavior of magnetite in lime-ferrite slag of the CaO-FeOX-Cu2O system. Recent improvements in the C-furnace operation have included the slag controls reflecting the impact of minor oxides on magnetite behavior. Although previous investigations focused on magnetite behavior, sulfur has also affected the C-furnace operation because it is of practical importance to avoid the precipitation of gypsum from lime-ferrite slag and the separation of matte from blister copper. This paper will quantify the behavior of sulfur in C-furnace with respect to the gypsum formation and matte separation, and discuss better controls for C-furnace operation.

Jan 1, 2006

By W. G. Davenport

Chapters 19 and 20 examine direcHo-copper flash smelting and flash converting. This chapter compares the two processes and suggests which is likely to be 'the more economic for a given concentrate. It: (a) uses Chapter 19's direct-to-copper industrial oxygen and oil requirements (b) adds the energy required for electric furnace recovery of Cu from direct-to-copper slag (Czemecki et al 1999) (c) combines Chapter 20's, flash converting calculations with Chapter 18's flash smelting calculations to determine their combined industrial oxygen and hydrocarbon fuel requirements (d) adds the energy required to granulate, crush and dry flash smelting matte for the flash converter (e) adds the energy required to granulate and dry flash converter slag for recycle to flash smelting (f) compares direct-to-copper and flash smelting/flash converting in terms of their total equivalent hydrocarbon ener.gy requirements.

Jan 1, 2001

By Carlos A. Nunes

V-AI alloys have been used commercially to produce pure vanadium by Electron Beam Melting (EBM), as well as to obtain Ti-based alloys (ex. Ti-6AI-4V). The aluminothermic reduction of vanadium pentoxide (V205) is the primary method to obtain these alloys. Concerning the obtention of pure vanadium, earlier studies have indicated alloys presenting Al content between 10 and 15wt% as the most suitable alloys for direct EBM. In the present work we investigated the aluminothermic reduction of V205 in order to define process parameters for the obtention of V-AI alloys with composition in the previously mentioned range. It was studied basically the effect of excess AI, CaO addition and reaction atmosphere (air, argon) on the alloy composition (AI, 0, N). In addition, microstructural analysis of selected alloys by SEM (BSE images) and EPMA (WDX) were also performed.

Jan 1, 1996

By D. J. Donaldson

The PAL process for recovering nickel from laterite ore requires large volumes of thick abrasive slurry to be raised lo high temperature (245°C+) and pressure (40 atm.+). Flow diagrams of the process typically result in facilities that have serious operating and reliability problems. Most of the problems can be attributed to using multiple pump stations to raise the slurry to autoclave pressure, large amounts of flash and live injection steam to heat the slurry to autoclave temperature and several steps of flash cooling to lower the temperature and pressure of the abrasive autoclave slurry down to atmospheric conditions. It is proposed that operating and reliability problems of PAL facilities can be mitigated by using Tube-in-tube heat exchangers and "float type" positive displacement pumps. The subject paper describes an innovative application of such equipment in the facility design of the PAL process. Keywords: Nickel, Laterite, PAL, Heating, Slurry

Jan 1, 2004

By Zhan Jing

Keywords: thermodynamic, Ni-Co alloy powders, composition, fibrous The mathematics model of Ni(II)-Co(II)-C2O42?-NH3?H2O-H2O of thermodynamic equilibrium system has been developed theoretically according to the law of conservation of mass and the law of simultaneous equilibrium, and the logarithm concentration-pH (log[Me2+]T-pH) diagrams of this system have been made. The effect of ligand and pH value was studied. Two issues in coprecipitation route to synthesize fibrous nickel-cobalt alloy precursor powder, com-position and morphology which are a first priority, are addressed based on thermodynamic analysis and experiments. The results show that suitable pH value range of coprecipitation of nickel ions and cobalt ions in theory can be obtained to maintain fibrous, excellent compositonal homogeneity and stoichiometry in coprecipitation products. Experimental demonstration is also carried out.

Jan 1, 2005

By Theo Lehner

Turning matte into anodes continues to be an area to watch: for visitors to see pyrometallurgy in action; for metallurgists to keep up with modern smelting furnaces and ever increasing production rates; for management to remain profitable using more tools than taught in school; and for environmentalists to detect the last small clouds from the ever cleaner smelter. Current converting practices have been screened and analyzed, and today, converting and casting is a modern industry. An impressive, though typical learning curve of converter productivity may be detected. Local conditions such as availability and type of raw materials, products extracted, cost factors, etc., have stimulated the development of add-ons or even alternatives to the still dominant method of converting by Peirce-Smith technology. Turning blister copper into anodes follows a similar path, namely increased productivity and improved quality. We dare to predict that development will continue.

Jan 1, 2005

By P. Umadevi

In the light of the discovery of the new super-conducting YBa2Cu3O7-x (YBCO), reactions in the Y2O3¬CuO-BaO system at 1300°C was investigated. The search was for any new phase that may be formed in the system at 1300°C (only 950°C reactions are known so far). 35 mixtures of different compositions were prepared and heated at 1300°C. No new phase was obtained. It was found that YBCO is decomposed at this temperature and Y2O3 and BaCO3 are the major components in the solid obtained after firing in air. However, on cooling the melt slowly and annealing at 950°C YBCO reforms. Such reactions on cooling might have implications on processing of the superconductor YBCO for practical applications as well as on its crystal growth by flux method.

Jan 1, 1989

By Tang Mo-tang

A new process for extracting indium from indium-zinc concentrates was proposed in this paper. The process can directly extract indium from removed copper solution by P204, and cancel the stage of removing iron in the traditional process because of using iron and part of zinc in the In-Zn concentrates for direct preparing high quality Mn-Zn soft magnetic ferrites. The technologies in the processes, such as leaching the neutral leached residues with high concentrated acid at high temperature, reduction ferric and removing copper, and extracting indium, were investigated. The results showed that total recovery ratio of indium has been increased from less than 70% in the traditional process to more than 95%. This process has the advantages of largely simplifying the procedure of indium extraction, zero draining off of iron residue and zero emitting of SO2. So this is a clean production process.

Jan 1, 2006

By Mitsuhiro Ohtaki, Tetsuzo Arakawa, Fujio Murata

Refining of Zn from aluminum scrap melt by some vacuum distillation processes was studied to promote aluminum scrap recycling. Effects of distillation conditions, such as melt temperature, vacuum pressure and holding time, on Zn distillation behavior were investigated theoretically and experimentally by 0.3kg/ch scale vacuum resistance furnace. Three methods to increase the surface-area/volume ratio of liquid metal, such as gas atomizing, mechanical atomizing and mechanical stirring, were tested to increase the Zn distillation rate in 5kg/ch scale vacuum resistance-furnace. It was easy to lower the remaining Zn content to less than 0.1 wt% within one minute by mechanical stirring method. A water-model simulation experiment indicated that a significant agitation of the melt by stirring would be effective to increase the distillation rate. Continuous agitation vacuum distillation process (CA VP) has been designed and the pilot plant is now in construction.

Jan 1, 2000

By I. Van de Voorde

In this paper, results are presented concerning the search to implement Supported Liquid Membranes (SLM) Technology for the recovery of copper, nickel and zinc from electroplating and other effluents to prevent metal waste. A study of the influence of the individual parameters and of their combined effect on mass transfer in small-scale laboratory equipment has been performed, enabling to set forward the appropiate operating conditions for a pilot plant installation. The SLM pilot plant has been tested extensively, including short and long term runs, with real process solutions. It was demonstrated that the SLM technolgy is applicable for solutions containing 800 mg/L of metal ions, but also to the treatment of solutions with low metal content of origin other than plating shops. It was demonstrated by system analysis that the recycled salts are usable to produce metal electrolytes (for example Watt's nickel bath).

Jan 1, 2003

By R. K. Amankwah

The ability of Streptomyces viridosporus in sorbing heavy metals from wastewater has been investigated. It was found out that the biomass of the soil microorganism could be used in sorbing Pb2+, Cu2+, Zn2+ and Ni2+ ions from acidic solutions of metal ion concentration between 10 and 100 ppm. Over 99% of Pb2+ and 88% of Cu2+ ions were sorbed from wastewater of concentration 10 ppm with Ni2+ and Zn2+ recording values below 50% for a contact period of 4 hours. The quantity of metal ions sorbed per gram of biomass from the wastewater was in the order Pb2+ > Cu2+ > Ni2+ > Zn2+ and this is related to their electronegativities. Biosorption was sensitive to variations in pH and in the range investigated; metal binding was optimum at 5.5. About 63% antimony was also sorbed from dilute cyanide solution.

Jan 1, 2003

By Chunlin Chen

Published data on thermodynamics of a number of minor elements (As, Sb, Bi, Pb, Zn, Se, Te, Cr, Sn) in liquid copper, matte and slag have been reviewed, assessed and used in development of thermodynamic solution models of melts. The behavior of antimony in alloys, mattes and slags is used as an example to illustrate the approach taken in assessment of published data and validation of the developed models with respect to the activity of Sb in condensed phases as well as the effects of matte grade, slag chemistry, temperature etc on the equilibrium distribution of Sb between melts and the gas phase. Results obtained from a comparison of different smelting processes with the modeled multi-phase equilibrium are presented and discussed. The predicted effects of slag chemistry and matte grade on the deportment of other minor elements during smelting of copper mattes will be presented and discussed.

Jan 1, 2006

By S. S. Chabot, S. E. James

A recent survey of major steel companies worldwide revealed the importance of recycling zinc units from electric arc furnace (EAF) dust, mill scale, blast furnace dust and other zinc containing streams within the steel industry. Many processes have been developed and installed in response to this challenge. The most successful approach involves the production of a crude zinc oxide and its sale to primary zinc producers to recover the metal values. The problem with this process is the high concentration of halides in the crude oxide. This type of material cannot be processed directly in an electrolytic zinc plant because of the corrosion problems it will cause in electrolysis. In 1999, Big River Zinc installed a zinc oxide receiving and washing plant to minimize the impact of halides in its electrolysis circuit. A description of the washing plant and the initial operating results are presented in this paper.

Jan 1, 2000

By D. N. Wilson

The potential risks of working with lead have been recognised for centuries, but it is only with the development of sensitive measuring techniques in relatively recent years that it has been possible to establish effective approaches for the monitoring and control of lead exposure. This paper examines the principal control measures employed today - lead in air and lead in blood - and reviews the evolution of numerical standards, with particular reference to the latest understanding of health effects. In addition to lead, a large number of other metals are commonly encountered when producing lead and zinc - both primary and secondary - and the health effects of many of these are discussed. Modern hygiene practices and technologies, which have proved successful in reducing worker exposures, are reviewed. The paper concludes with a look at how exposure standards are likely to change in the near to medium future

Jan 1, 2000

By Cyro Takano

This paper is a contribution to fundamentals data on the equilibrium metal/slag for refining silicon in relation to Ca and Al as impurities. Silicon containing 0.1% Al and no Ca was placed in contact with a slag of various contents of CaO, SiO2 and Al2O3. Slag Al2O3 contents were 11.4%, 25.1% and 29.6%, keeping the ratio %CaO/%SiO2 constant and equal to ~0.53. The experiments were conducted at 1550oC, in a graphite crucible with argon atmosphere. The equilibrium was observed with low and medium content of Al2O3. The derived activities coefficients of Ca and Al in dilute solution of Si presented good correlation with those of the literature. Parallel reactions with formations of SiO(g) and CO (g) were also observed.

Jan 1, 2006

By John O. Marsden

In early 1998, Phelps Dodge embarked upon a program to investigate alternative technology for the extraction and recovery of copper, and other metal values, from copper concentrates. A review of all of the available process alternatives indicated that many were unsuitable for large-scale commercial application and others were clearly targeted at niche applications where contaminants (and consequently smelter penalties) were driving the decision-making. The result of this development program is the world?s first commercial application of high temperature pressure leaching of chalcopyrite concentrate at Bagdad, Arizona, which was commissioned in the second quarter of 2003. Other related processes are in various stages of development. In addition to the obvious considerations, the economic aspects of this technology have been considered in detail at each step in the development of the program. The technology developments in this area are reviewed with emphasis on the economic viability and commercial application.

Jan 1, 2003

By Jung-Ah Kim

Precipitated Calcium Carbonate (PCC) is obtained through calcination, hydration, and carbonation. Thus, the change in each process condition determines the particle size or morphology of PCC. To date, studies on precipitated calcium carbonate have mainly focused on process manufacturing PCC, aimed matter. Still, few studies on calcination or hydration have been conducted. Therefore, this study sought to investigate the effect of hydration condition on the synthesis characteristics of aragonite PCC. Results showed that the particle size of calcium hydroxide changed based on the variation of the initial hydration temperature. In particular, higher initial temperature resulted in the larger particle size of calcium hydroxide used in synthesis. The particle size and yield of aragonite also increased when calcium hydroxide made at high temperature was used. The water/solid ratio or total amount at the hydration time had no effect on the manufacturing process of aragonite, however.

Jan 1, 2006

By Shunichi Ajima

PT. Smelting Co. was established in February, 1996 to construct and operate the Gresik Smelter and Refinery. The construction work of first Copper Smelter and Refinery in Indonesia was completed in the end of August, 1998 and it was put into the integrated test operation in December, 1998. Gresik Smelter and Refinery is designed to produce 200,000 tpy of copper cathode from copper concentrate supplied from Grasberg Mine of PT. Freeport Indonesia Company in Irian Jaya, Indonesia. As by product 592,000 tpy of sulfuric acid, 382,000 tpy of slag, 31,000 tpy of gypsum and 480 tpy of slime will be produced in the full operation. Major processes applied at Gresik Smelter and Refinery are: Smelter: Mitsubishi Continuous Copper Smelting and Converting Process ( Mitsubishi Process ) Anode Casting: Continuous Casting of Copper Anodes with the Hazelett Twin Belt Caster Refinery: ISA Process Acid Plant: Lurgi Mitsubishi Double Contact Process

Jan 1, 1999