Search Documents

By Robert B. Haagensen

While light optical microscopy has long been employed by the mineral processing industry, there has been a tendency to shy away from its use for all but the most exacting purposes. Despite the usefulness of micros-copy in solving a wide variety of problems, the response to such work is often less than enthusiastic primarily due to time considerations. Microscopical techniques are therefore often relegated to the "ivory tower" and their direct and practical application to everyday problem solving over-looked. The purpose of this paper is to dispel such attitudes and promote a wider use of light microscopy. Several examples are given which point out the indispensib1e nature of optical microscopy as a rapid means of defining and solving problems in mineral processing. The application of other instrumental techniques to augment the information obtained is also discussed, particularly the value of the combined use of the optical microscope and electron probe micro-analyzer.

Jan 1, 1981

By A. G. Merma

In this work, the electrocoagulation technique was studied in order to treat chemically stabilized concentrated oil-water emulsions. This study was mainly focused on the effects of operating parameters such as initial pH, current density, reaction time, electrode distance and inlet concentration on the separation of oil as measured by the chemical oxygen demand -1(COD) method. The synthetic emulsion was prepared from Shell - Talpa 30 oil (3g.L-1) and sodium dodecyl sulfate (1.0 g.L), having a Zeta potential around -70 mv at pH 8.7. The process was carried out in an electrocoagulation cell with a set of four parallel monopolar electrodes. This set consisted of two aluminum plate anodes and two 316L stainless steel plate cathodes. Kinetic curves showed that the electrocoagulation process exhibits three phases: (1) an initial phase, where the COD did not decrease because the solution had not reached the minimum amount of dissolved aluminum required to cause the break-up of the emulsion, (2) a reactive phase during which COD decreased due to possible agglomeration of the precipitates and (3) a steady-state phase where the COD did not change. The results showed that the period to reach the reactive phase decreased as the current density increased and the pH values decreased.

Jan 1, 2009

By Pier-Lorenzo Solari, Philippe Moisy, Michel Schlegel, Stephane Pellet-Rostaing, Eric Mendes, David Bengio, Richard Husar, Thomas Dumas

Ionic liquids (ILs) are molten salts composed of an organic cation that are liquid below 100 °C. They demonstrate unique physico-chemical properties such as good conductivity, negligible vapor pressure and non-flammability. As a consequence, they are often regarded as green solvents and could become an alternative to the use of both high-temperature molten salts and volatile organic solvents in rare-earth elements processing and recycling. The diversity of interactions existing in an ionic liquid allows the solubilization of both polar and apolar compounds. Moreover, coordinating functions on their composing ions can lead to stabilization of some species. For instance, in non-aqueous media, europium exists in the (II) oxidation state which is not stable in aqueous solutions. Understanding the mechanism of Eu(III) electrochemical reduction to Eu(II) and the stabilization of Eu(II) species in IL media could be of major interest for the development of innovative recycling processes. Using transient electrochemistry and UV-Vis spectroscopy we could get valuable information on the redox behavior of the Eu(III)/(II) couple in the ionic liquid 1-ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide ([EMIm][NTf2]). Reduction of Eu(III) to Eu(II) and stability of Eu(II) was also studied thanks to a XAS-spectroelectrochemistry set up used to follow in situ the evolution of the XANES spectrum around the L3 edge of Eu during electrolysis.

Mar 1, 2018

By Daniel S. Gwinner

The tolling, or processing for a fixed fee, of aluminum drosses to recover the metal units is a common practice in the Aluminum Industry. The Dross Toller is acting for the owner, and since most dross processes result in material going to landfill, it is important for the owner of the dross to insure that the toiler is processing the material and handling waste disposal in an environmentally responsible manner. The paper discusses the Dross Toiler Audit Program, first from the Reynolds Metals Company perspective. Included are the reasons the company deems it necessary to audit and a description of the items covered during the audit. Finally, there will be a discussion of the audit from the Tollers perspective - what the Toiler can expect when the auditor arrives.

Jan 1, 1995

By F. -Z. Ji

Carbon injection into metallurgical slag is important in electric arc furnace (EAF) steelmaking for foamy slag practices and in nonferrous slag cleaning operations. The current publication presents kinetic data for coal injection into EAF slag to understand the interaction between injected carbon and metallurgical slag. Coal particles were injected into EAF slag and the kinetics were followed by gas and slag analysis. The results were analyzed, in terms of fundamental rate equations for each possible reaction step, as a function of temperature and slag composition.

Jan 1, 2003

By Hai-Peng Guo, Lu Jiang, Xiao-Man Yan, Bing Xie, Hong-Yi Li

Traditional, calcium compounds cannot be used in vanadium extraction processing due to the limitation of sodium roasting technology, which results in unsatisfied dephosphorization for vanadium-containing hot metal in converter and thus increasing the dephosphorization burden for subsequent steelmaking. The calcium roasting technology is an alternative for vanadium extraction and allows adding lime into vanadium slag in converter. In the present study, vanadium was leached by soda from roasted vanadium slag with high calcium content. Effects of roasting temperature and time, leaching temperature, Na2CO3 concentration andliquid to solid ratio on vanadium leaching rate were studied. The results show that 94% of vanadium was extracted by roasting the vanadium slag at 950℃ for 2.5h and then leaching in 160g/L Na2CO3 liquid at 95℃ for 1h with liquid to solid ratio of 10:1 ml/g. Impurities of Si and P reacted with calcium and formed insoluble Ca2SiO4 and Ca3(PO4)2 respectively.

Jan 1, 2015

By M. A. H. Shuva, M. A. Rhamdhani, G. A. Brooks, S. H. Masood, M. A. Reuter

Ferrous-calcium-silicate (FCS) based slag has been used in the copper industry over the last two decades. The FCS slag has also been used in a secondary copper processing such as in black copper smelting which has different operation conditions compared to that of typical primary copper processing. In the process, a variety of copper bearing scraps from sources such as industrial waste, consumer waste and electronic waste (e-waste) are used. The valuable metals in these sec- ondary resources are distributed in different phases during the process. Understanding the behaviour of the valuable elements at the relevant conditions is vital for optimizing the process and to maximize the recovery of the elements. In this study, we investigated the structure of Ge-containing FCS-based slag at different conditions (oxygen partial pressure and temperature) using Fourier-Transform Infrared (FTIR) spectroscopy to explore the effect of the polymerization on the behaviour of the valuable element Ge in the slag. It was found that experimental parameters significantly in fluence the slag structure, and therefore, the partitioning of Ge in the slag. A correlation between the distribution ratio of Ge and the slag structure has developed in the current study.

Mar 1, 2018

By Muammer Kaya

The purpose of this review is to raise awareness about e-waste problem in the World. Whether generated at our home or our office, e-waste is most rapidly growing waste problem in the world. Even though there are conventional disposal methods (such as landfill and incineration) for e-waste, these methods have both economic and environmental disadvantages; recycling is a new waste management option which diverts end-of-life (EOL) electrical and electronic equipment (EEE) from landfill and incineration [1, 2]. Successful diversion strategy must be based on economic sustainability, technical feasibility and social support [3]. Recycling infrastructure includes transportation, collection, recovery and resale establishments. The first part of this paper describes the e-waste facts, how big is the e-waste problem and existing recycling programmes and collecting methods in the USA and EU; second part, describes various methods available to recover valuable materials (glass, plastic and metals (Pb, Cu, Al, Steel, Ni, Au, Pd, Cu etc)) in e-waste for a safe and environmental friendly disposal

Jan 1, 2009

By G. Djambazov, D. Shevchenko, D. Burnard, V. Bojarevics, K. A. Pericleous, W. Griffiths

Contactless ultrasound treatment can be useful for high-temperature or reactive alloys in the liquid state, where contact with an immersed vibrating probe is undesirable. The alternating component of the Lorentz force can generate sound pressure levels leading to cavitation of gas bubbles in the melt, through acoustic resonance. Resonance is a function of the speed of sound in the liquid, the shape of the volume containing it and surrounding boundary conditions. Induction forces applied to a crucible lead to bulk stirring and in general deform the free surface, whose precise shape may influence the resonance conditions. This effect is investigated here b ymulti-physics computer modelling. Calculated results for aluminium melts are compared with experimental data and conclusions are drawn as to the sensitivity to process parameters and the reliability of this type of ultrasound metal processing.

Mar 1, 2017

By Wei Yu, Tiejun Chun, Jian Pan, Deqing Zhu

In this paper, improving the pelletization of Brazilian hematite by adding a boron bearing additive was carried out, and the pelletization parameters were also optimized. The mechanism of boron bearing additive was revealed in the kinetics of crystal grain growth by using LEICA microscopy and its software to measure hematite grain growth. Good qualities of green balls are manufactured with drop numbers above 5.7 times/0.5m, compressive strength higher than 13 N/pellet and thermal shock temperature over 620? under the following conditions: 1.2wt% bentonite, 0.4wt% boron bearing additive, 7wt% moisture and pelletizing in disc for 15 min. When the green balls were preheated at 1000? for 8 min and fired at 1280? for 15 min, the compressive strength of the fired pellets containing boron bearing additive is about 3096 N/pellet, which is far beyond the standard requirement for good quality pellets. Compared to the fired pellets without adding any boron bearing additives, the compressive strength of fired pellets containing boron bearing additive is increased by 1225 N/pellet. It is revealed that adding boron additive into the hematite pellets help to form more liquid phases, lower the activation energy of the hematite grain growth by 135.2 kJ/mol and increase grain growth rate by 33.6%, leading to higher strength of fired pellets due to forming more coarse and dense recrystallized hematite and energy saving by firing at lower temperatures for shorten time.

Jan 1, 2011

By W. J. Mitchell

During the months of April and May 1992, the Phelps Dodge Hidalgo smelter underwent a major turnaround. This was the third such turnaround in the life of the facility which was commissioned in 1976. During the third furnace campaign, the smelter processed 5.2 million tons of concentrate producing 2.6 billion pounds of anode copper over a 7.5 year period. The critical path on the fifty-nine (59) day turnaround schedule was the reconstruction of the Outokumpo flash furnace which integrated some modifications with standard rebuild practices. Modifications included incorporation of horizontal cooling jackets throughout the furnace settler as well as the installation of castable refractory in the reaction and uptake shafts.

Jan 1, 1993

By Ann M. Hagni

Microscopic and sub-microscopic gold commonly occurs in the sulfides pyrite (FeS2) and arsenopyrite (FeAsS). To recover refractory gold from pyrite and arsenopyrite, these sulfides are roasted to create porosity and permeability prior to cyanide leaching. A new technique of adding Ca(OH)2 and roasting, lime roasting, is being tested fro retention of contaminant sulfur and arsenic and effectiveness of gold extraction. The lime roasting of pyrite at 500°C contains anhydrite (CaS04), oldhamite (CaS), calcium sulfite (CaS03), hematite (FenOs), magnetite (Fe304), and minor amoupts of pyrrhotite (Fel.,S) and pyrite. At 600°C, 650°C and 700°C the main constituents are anhydrite, oldhamite, and hematite. At 750°C, 800°C, and 850°C anhydrite and hematite are the predominant phases with minor oldhamite. The roasted arsenopyrite at 450°C contains arsenic sulfides, calcium sulfite, hematite, and minor oldhamite, magnetite, and pyrrhotite. At 650°C 700°C 750°C and 800°C, anhydrite, oldhamite, arsenic sulfides, and hematite are present. At 850°C, the same minerals are present with only minor oldhamite. The textures indicate excellent porosity and permeability at high temperatures. At lower temperatures, rims of low porosity and permeability surround many of the pyrite and arsenopyrite particles, and the complete oxidation process from pyrite to pyrrhotite to magnetite to hematite can be observed in individual particles. Additional process mineralogy techniques employed in this study are electron spectroscopy for chemical analysis (ESCA) and cathodoluminescence microscopy (CLM) in the determination of the calcium-sulfur- oxygen phases. Automated scanning electron microscopy-energy dispersive spectroscopy was utilized to analyze particles for gold content. Reflected light microscopy (RLM) revealed arsenopyrite and pyrite encapsulated in quartz particles of the gold-bearing concentrate, gold roast calcine, and cyanide leach residue.

Jan 1, 1993

By Ann M. Hagni

Microscopic and sub-microscopic gold commonly occurs in the sulfides pyrite (FeS2) and arsenopyrite (FeAsS). To recover refractory gold from pyrite and arsenopyrite, these sulfides are roasted to create porosity and permeability prior to cyanide leaching. A new technique of adding Ca(OH)2 and roasting. lime roasting. is being tested for retention of contaminant sulfur and arsenic and effectiveness of gold extraction. The lime roasting of pyrite at 500°C contains anhydrite (CaS04). oldhamite (CaS). calcium sulfite (CaS03). hematite (Fe2O:J), magnetite (Fe304). and minor amounts of pyrrhotite (Fe1.xS) and pyrite. At 600°C. 650°C and 700°C. the main constituents are anhydrite. oldhamite. and hematite. At 750°C. 800°C. and 850°C. anhydrite and hematite are the predominant phases with minor oldhamite. The roasted arsenopyrite at 450°C contains arsenic sulfides. calcium sulfite. hematite. and minor oldhamite. magnetite. and pyrrhotite. At 650°C. 700°C, 750°C. and 800°C, anhydrite, oldhamite. arsenic sulfides, and hematite are present. At 850°C. the same minerals are present with only minor oldhamite. The textures indicate excellent porosity and permeability at high temperatures. At lower temperatures, rims of low porosity and permeability surround many of the pyrite and arsenopyrite particles, and the complete oxidation process from pyrite to pyrrhotite to magnetite to hematite can be observed in individual particles. Additional process mineralogy techniques employed in this study are electron spectroscopy for chemical analysis (ESCA) and cathodoluminescence microscopy (CIM) in the determination of the calcium-sulfur-oxygen phases. Automated scanning electron microscopy-energy dispersive spectroscopy was utilized to analyze particles for gold content. Reflected light microscopy (RIM) revealed arsenopyrite and pyrite encapsulated in quartz particles of the gold-bearing concentrate, gold roast calcine, and cyanide leach residue.

Jan 1, 1991

By Paula Ana Paiva

The high economic value and unique technological properties of the platinum-group metals (PGMs), plus their growing scarcity in the Earth’s crust, justify the crucial importance of developing recycling practices for PGMs end-of-life materials. Examples of top devices relying on the use of PGMs are automotive and industrial catalysts, and electrical and electronics equipment. This article critically describes the most recent research on the use of solvent extraction to recover one PGM, palladium, from spent catalysts. Some groups focus on the development of schemes involving commercial extractants, while others prefer to design specific molecules to efficiently and selectively recover palladium from these particular complex leaching solutions. Examples of commercial extractants proposed for the former schemes are Alamine® 308, TBP and LIX® 84I; while on the other hand, sulfur-containing diamides, thioamides, thiocarbamates, and dithioethers have recently been developed. Ionic liquids have to be mentioned too.

Carbon injection into metallurgical slag is important in electric arc furnace (EAF) steelmaking for foamy slag practices and in nonferrous slag cleaning operations. The current publication presents kinetic data for coal injection into EAF slag to understand the interaction between injected carbon and metallurgical slag. Coal particles were injected into EAF slag and the kinetics were followed by gas and slag analysis. The results were analyzed, in terms of fundamental rate equations for each possible reaction step, as a function of temperature and slag composition.

Jan 1, 2003

By J. Chen Kuriyama

One method to store hydrogen effectively involves the use of metal complexes such as the alkali-element aluminum hydrides. The hydriding/dehydriding properties of these materials depend on how to prepare them with different structures and microstructures. The present work focused on a high-energy ball milling technique to produce Ti-doped lithium tetrahydridoaluminate (LiA1H4) and lithium hexahydroalanate (Li3AIH6) powders with nanocrystallites. The phase structures and dehydriding/rehydriding characteristics were investigated by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, Brunauer-Emmett-Teller measurement, thermogravimetry, and differential scanning calorimetry. The mechanism of dehydrogenation and rehydrogenation was also examined by means of X-ray photoelectron spectroscopy (XPS). The results on the relation between the reversible hydrogen storage and catalysis function of the Ti-doped complex hydride indicate that both the homogenous distribution of Ti+AI nanoclusters and the Ti¬catalyst with Ti e> Ti3+ (Ti0/Ti2+/Ti3+) defect sites play important roles in optimizing the reversible hydrogen storage.

Jan 1, 2002

By Olexandr Gydin

The evolution of grain and dislocation structures during cold deformation of the new steel LH800 of Salzgitter AG is investigated in the frame of this work. The main feature of this material is its ability to air-harden by carbon content of about 0.1%. The initial ferrite structure of the metal provides high plasticity at cold deformation and subsequent heat treatment increases tensile strength approximately two times. Described are results of in-situ tensile tests in the SEM. SEM and TEM analysis of grain and dislocation structures evolution in samples, which have been uniaxially deformed to certain strains, are carried out. After statistical evaluation of results the grain elongation against strain is determined. A microstructure of a deep drawn cup is analyzed by means of SEM. A quantitative evaluation of grain elongation on the different cup zones and comparison of these data with prediction results based on tensile tests are carried out.

Jan 1, 2009

By Marcelo B. Mourão

An experimental investigation was carried out to -study the rates of reduction of pellets containing iron oxides by carbon dissolved in liquid iron, at temperatures ranging from 1720 K to 1973 K. Several different pellet types were employed; the materials used in the pellet's manufacture were pure hematite, two kinds of commercial iron ores, and mixtures hematite/silica and hematite/lime: Reaction times were determined employing the constant volume pressure increase technique (CVPI). It has been observed that the reaction rate increases as the temperature and the pellet's specific surface area increases. The reaction rate is also affected by the oxide type: pellets made from commercial ores or from mixtures hematite/silica or hematite/lime show reaction rates lower than those made from pure hematite.

Jan 1, 1996

By Steve Lloyd, Ryan J. Foy, Brandon Steinborn, Jerome P. Downey

Research was performed to evaluate copper and silver extraction from samples of bornite flotation concentrate. Sulfation roasting experiments were performed in a rotary tube furnace, a fluidized bed reactor, and a static bed muffle furnace. Roasting was plagued with rapid, lowtemperature calcine sintering, apparently related to the presence of organic matter in the concentrate. Calcine entered a weak acid leaching process to remove copper, and silver was extracted from the weak acid leach residue in a ferric chloride and hydrochloric acid solution. Copper extraction efficiencies in excess of 90% were attained in the weak acid leach while 90% silver extraction was achieved in the ferric chloride leach, along with copper and lead extractions as high as 93% and 99% respectively. The two-stage leaching process resulted in overall extraction efficiencies of 99% copper and 90% silver.

Jan 1, 2015

Two pilot-plant investigations were conducted in which strong-base resins were compared with activated carbon for the extraction of gold cyanide from leached pulp from the Golden Jubilee Mine. The results show that gold can be recovered with carbon, but that the extraction efficiency is poor, probably because high concentrations of humic and fulvic acids are. present m the pulp. .However the extraction of gold cyamde from this material with strong-base resins JS very effo:1ent, and the overall efficiency of extraction is better with resin than with carbon, even when the concentration of resin is one-third that of carbon, and the flowrate of resin is one-third that of carbon. The results of the pilot-plant campaign reported in this paper led to the conversion of the Golden Jubilee plant from carbon-in-pulp to resin-in-pulp in February 1988.

Jan 1, 1989