Search Documents

By Gerald Onyedika, Tochi Onwumere, Martin Ogwuegbu

"The kinetic study for the leaching of iron from cassiterite ore in KOH solution was studied. The effects of KOH concentration, particle size and reaction temperature on the leaching rate of iron were also examined. The results of leaching studies showed that the leaching of iron from cassiterite ore in KOH solution is significantly influenced by the reaction temperature, KOH concentration, and decrease in particle size. The study showed that 90.62% of iron ore was leached in 8M KOH solution at 80°C within 120 minutes. The experimental data were well evaluated using the shrinking model for surface chemical reaction and diffusion control through the product layer. The activation energies for the iron ore dissolution using the two models were calculated to be 32.06KJmor1 and 97.97 KJmor' respectively.IntroductionIn recent times, there has been increasing attention on the kinetic study of mineral dissolution. In most of these studies, the experimental results were analyzed with a suitable shrinking core model under the assumption that the ore is a homogeneous spherical solid phase [1-4]. A study of the dissolution kinetics of a Nigerian cassiterite ore by hydrochloric acid showed that increase in the hydrochloric acid concentration is accompanied with increase in the amount of cassiterite ore dissolved at various times [4]. The optimal concentration was found to be 4.0M HCl, after which there was a decline in the amount of the ore dissolved, which showed that the concentration of the reagent has a significant effect on the leaching rate of the ore. Also in studying the effect of stirring speed on the rate of cassiterite ore dissolution while keeping other conditions constant for 120 minutes, the result showed that the rate of cassiterite ore dissolution was dependent on the stirring speed over a range of 0 to 630 rpm. Above 360 rpm, the stirring speed no longer had any effect on the solid dissolution. The dissolution rates of cassiterite were analyzed using a suitable shrinking model. The results showed that the reaction was controlled by the diffusion of tin through the porous product layer, a reaction order with respect to hydrogen ion concentration of 0.92 M and activation energy of 50.05KJmor'. In another kinetic study on the leaching of a low grade niobium-tantalum ore with concentrated KOH solution the effect ofreaction temperature, KOH concentration, agitation speed, particle size and alkali-to-ore mass ratio on the dissolution rate of niobium were examined [5]. The result of niobium leaching from low grade niobium-tantalum ore with concentrated KOH, solution at different agitation speeds showed that the dissolution rate increased with increase in agitation rate. In the case of particle size effect, the results show that small particles require much shorter time for complete dissolution than the large ones."

Jan 1, 2013

By Akio Ohta

The Hyuga smelter has been producing ferronickel by a rotary kiln-electric furnace process in Miyazaki, Japan. Several approaches to improve our operation have decreased the electrical energy consumption. A new process was developed to decrease the cost of energy even further. Oil and technical oxygen are injected through lances to heat up the calcined ores (calcine) instead of the electric power. Main problems during the development of the process were the short life of the water-cooled lances, the check on security of the safety system and the eruption of combustion gases through the calcine bed. These problems have now been overcome successfully, and stable operation can be maintained. The addition of 1 Litre of heavy oil per tonne of ore can save the electrical energy requirement by 8.6 kwh per tonne of ore. The new process has resulted in a reduction of the electrical energy consumption by more than 10 percent

Jan 1, 1992

By Chen Wen, Li Zhao-jia, Zhao Qiang, Ning Shun-ming, Tang Sanchuan, Wang Hong-qiang

"The carbon-burdened and cold-bonded pelletizing-electrosmelting process is used to dispose low-grade manganese, and the qualified rich-manganese slag is obtained. On the condition that reduction roasting temperature was 1000?, reduction time was 45min, particle-size was -1mm, reductant dosage was 1.6%, basicity was 0.3, smelting temperature was 1410?, smelting time was 60min, it had a good effect on the melting between slag and metallographic phase, the manganese content was 32.58%, manganese recovery was 92.16% in the slag; while the iron content was 94.40%, iron recovery was 95.32% in the metallographic phase. It was proved by the demonstration tests.IntroductionManganese is an important raw material for steelmaking, which is extensively utilized in modern industry, the consumption of manganese for iron and steel industry accounts for 90% to 95%. After mining over 30 years, the high-grade manganese resources drop markedly, especially with the hypergrowth of steel industry, the domestic manganese is far from the requirement, as a result, we have to buy significant quantities of manganese overseas. Besides, the property of imported manganese is more and more complex, and the high-grade and lump manganese decrease year by year, while the fines and high-crystal water manganese are on the increase. Therefore, how to make effective use of domestic low-grade manganese and intensify the manganese’s smelting is an effective approach to reduce the cost of manganese series ferroalloy and improves market competitiveness[1-4]. It has important practical meaning."

Jan 1, 2012

By Marcel Magnusson, Guozhu Ye, Pekka Vaananen, Yang Tian

The most used technology for recycling of spent alkaline batteries consists of crushing, magnetic separation and processing of the nonmagnetic fraction, black mass, using a rotary kiln. In the process only zinc is recovered and all manganese in the black mass is lost. According to the EU regulation for recycling of batteries, more than 50% of batteries should be recovered. To meet the demand, Swerea MEFOS has together with a major battery recycler IsoLogistics in Finland and Sweden developed technologies for efficient recovery of zinc and manganese aiming for >50% recovery. This paper will focus on a treatment process using a DC furnace to produce a ZnO- and a MnO-product. The process has been demonstrated in pilot scale, 1 ton/h. The major outcomes will be highlighted. Another approach by using thermal vacuum technology for distillation of zinc metal has also been demonstrated in laboratory scale which is also reported in this paper.

Mar 1, 2018

By Zhigang Liang

Investigation into the mixing of 150t ladle furnace by two-nozzle jetting was performed by a water model simulation of 1:4. The effects of nozzle arrangements including separation angle, radial position and asymmetry as well as tracer adding position on the mixing time were studied. The most favorable mixing is achieved when the two nozzles are symmetrically arranged at half radii in the ladle, with 45o separation angle. The empirical relationship between the mixing time and stirring power intensity has been established for two-nozzle jetting based on the present experimental results. In addition, the swelling above bath surface is also investigated with two-nozzle jetting.

Jan 1, 2009

By M. Bugdayci, Onuralp Yucel, K. C. Tasyurek

This paper is a contribution to the theory and quantitative understanding of the processes for the production of magnesium, calcium and strontium metals by metallothermic process. In the present study, effect of reductant type was investigated. Thermodynamic simulation of system was made by Fact Sage 6.4 program. In order to produce magnesium metal, effects of reductants “FeSi, Al, Si and CaC2” were investigated. To understand Calcium-oxide reduction system, effects of Al and CaF2 addition were investigated for different temperatures. In the last simulations, SrO reduction parameters were simulated. Al used as main reductant and BaO, CaO, CaC2 were added to green mixture as a functional additive. Finally probable phases and minimum reduction temperatures are determined.

Mar 1, 2018

By H. Doostmohammadi

During the tapping of liquid steel from Electric Arc Furnace (EAF), some slag is carried over into the ladle. High levels of FeO and MnO in slag carryover increase the oxygen activity in steel melt leading to oxide inclusion formation during the ladle treatment. The demand on cleaner steels requires minimization of carryover slag. In this work, the effect of EAF slag carryover on ladle slag-steel equilibrium calculations for a hot working tool steel was studied. Steel and slag sampling were done in Uddeholm Tooling AB in Sweden. XRF and OES techniques were used to determine chemical composition of samples. The quantity of slag carryover was calculated based on a mass balance followed by thermodynamic calculations on metal-slag equilibrium using Thermo-Calc software. The agreement between predictions and experimentally determined compositions was good. This leads to the development of a prediction method for optimizing the production of other tool steel grades.

Jan 1, 2009

By E. I. Gedgagov, A. V. Tarasov, V. M. Paretsky, A. D. Besser

"Hydrometallurgical technology and equipment have been developed in the Gintsvetmet Institute (Moscow, Russia) for processing of rhenium-containing alloys waste to produce commercial- grade metal products with recovery of all valuable components. The technology is based on waste treatment with hydrofluoric acid with subsequent decomposition with nitric acid at pH = 1 to 1.5 to ensure maximum degree of rhenium conversion to the liquid phase of pulp. Some experimental lots of ammonium rhenate and ammonium molybdate were produced at a pilot plant. The following main techno-economic performance values have been achieved when processing grinding residues (balance-based tests were conducted with a lot of SP-2 alloy waste) to produce ammonium rhenate of high purity, as well as tantalum-niobium, nickel-cobalt and tungsten-molybdenum concentrates: rhenium recovery of 92.3% into a commercial product from grinding waste; production cost of 170-210 US Dollars per 1 kg of rhenium in commercial-grade ammonium perrhenate taking into account its recovery; tantalum and niobium recovery of 75- 77% into bulk concentrate; nickel and cobalt recovery of 88-89% into a mixed concentrate; tungsten and molybdenum recovery of 88% to 91% into concentrate. Introduction During the recent years the use of rhenium has been increasing at a fast pace worldwide [1]. The growing prices for this refractory metal are an essential factor encouraging collection and processing of rhenium-containing wastes. Double-component waste, such as molybdenum- rhenium or tungsten-rhenium alloys can be readily decomposed and the process of rhenium recovery does not cause, therefore, any difficulties. The main separation of metals takes place at the stage of waste digestion with acid, because molybdenum and especially tungsten remain in precipitate in the form of hydrated oxides and rhenium reports in the liquid phase, from which it can be easily extracted by solid ion-exchange or solvent extraction techniques. However, most of rhenium is contained in super-alloy waste [2]. Such waste has different contents of valuable components, such as tantalum, niobium, molybdenum, tungsten, cobalt, nickel, chromium and other metals. The basis of all such super-alloy waste is nickel. Refractory metals in the super- alloy composition are in the form of metallized target-oriented eutectics, and due to this reason hydrometallurgical decomposition of such alloys is a difficult technological task."

Jan 1, 2008

By Fang Wu

The paper designs an extraction flow for the total recovery of nickel and cobalt and removing magnesium simultaneously from the cadthodic materials of the spent hydrogen-nickel and cadmium-nickel batteries. The separation of Co, Ni and Mg though P507 extraction .The extraction equilibrium pH is 4.5~5.0, ßNi/Co is 140~180, and ß Ni/Mg is 20~25; nickel and magnesium are scrubbed in two steps, in which the equilibrium pH of nickel and magnesium scrubbing is controlled at 5.0±0.1 and 4.4±0.1 respectively. The stepwise scrubbing technique is adopted to remove 94.5% of magnesium and to recover 99.45% of nickel and 95.35% of cobalt. During the integrated extraction and precipitation process the total recovery fraction of nickel and cobalt are 99.99% and 99.95%, and the recovery fraction of magnesium is 94.02%.The recovered NiSO4 and CoSO4 solution are enriched and crystallized.

Jan 1, 2009

By J. Phillip Mackey

The Peter Hayes Symposium on Pyrometallurgy, held as part of Extraction 2018, is an acknowledgement of his contributions to the basic science and principles underpinning modern pyrometallurgical processing. After completing his PhD at Strathclyde University, Scotland, in 1974, Peter took up a teaching position at The University of Queensland, Brisbane, Queensland, Australia in 1976. Peter Hayes’ research at the University since then has been focussed on: • The mechanisms and kinetics of heterogeneous solid/solid, gas/solid and liquid/ solid reactions, and • Experimental measurement of phase equilibria in complex high temperature metallurgical systems. This paper provides a brief biography of Dr. Peter Hayes and gives a full listing of Peter Hayes’ publications.

By Sue Ritz

Gold extraction has relied on coconut carbon in adsorption circuits for several decades. IXOS®, invented by 6th Wave Innovations of Salt Lake City, Utah, is a new type of adsorbent that exceeds the selectivity of carbon and improves on the mechanical properties of other available resins. IXOS selectivity against copper cyanide complexes allows it to be used in circuits that currently struggle with copper contamination. IXOS potential to eliminate or reduce the application of SART technology will expand the opportunities to exploit more complex precious metals deposits. This paper will describe the technology behind IXOS molecular imprint, its comparison to carbon adsorption in the field, and the effect of efficiency on long-term recovery from heap leach METSIM simulation software.

By Z. Zhang, R. G. Reddy

The viscosities of industrial lead slags with various compositions were measured as a function of temperature. It was found that viscosities of lead slags decreased with increasing temperature, and the plots of ln(11) vs. 104tr followed a linear relation over the reported ranges of temperature. Using the data of this study and available other related data from the literature, a viscosity expression was developed as a function of composition and temperature. The calculated results using this viscosity expression are in good agreement with the measured data. The composition dependency of viscosity of lead slags is discussed.

Jan 1, 2000

By W. -S. Hwang, R. A. Stoehr, P. Ingerslev

"The flow of molten metal entering complex two-dimensional foundry molds has been modeled using the Simplified Marker and Cell (SMAC) and Solution Algorithm (SOLA) techniques. The molds were for a series of four and three-spoke wheel designs. The computer calculations were compared to physical experiments in which molten cast iron was poured into C02-bonded sand molds. The metal was photographed with a high speed motion picture camera focused through a Pyrex glass window on one face of the mold. To get good agreement between the calculations and the experiments, it was necessary to accurately represent the velocity through the ingate. This was calculated by application of the Bernoulli equation to flow through the feed system. Some difficulties were experienced with mathematical instability, expecially in the three-spoke design with a narrow ingate. This was overcome by using 100% upwind differencing, and over relaxation parameter near 1.0 (i.e. no over relaxation), and variable mesh spacing.IntroductionModeling the flow of molten metal entering molds has the potential for making significant contributions to the design of feed systems. It will supply information to the computer-aided-design systems of the future that will enable the designer to optimize the placement of gates, dimensioning of passages, and designation of casting speeds. Such design criteria have generally been based on application of energy balance (Bernoulli equation) principles to flow in the sprues, runners, and gates. Indeed, this is the easiest way to determine the proper dimensions to give a suitable filling time for a casting of a given size. A number of computer programs, including one by some of the present authors, have integrated such calculations into CAD systems. l Modeling the flow of metal inside the mold cavity requires other techniques that will handle free-surface transient flow. Stoehr and Hwang reported on the application of the Marker-and-Cell (MAC) technique to mold filling problems at the previous conference in this series at Hennicker, N.H. in 1983. 2 Although considerable progress has been made since that time in improving the accuracy, stability, and convenience of these techniques, the shapes to which they were applied remained limited. Also, physical verification of the results of the calculations was limited to water models.The work to be reported in this paper was undertaken with two objectives: (1) to apply these techniques to more complex and realistic shapes, and (2) to verify the results by comparison with flow patterns observed in molten metal poured into actual sand molds."

Jan 1, 1986

By Chuanlin Fan

The process of flotation separation and recycling of spent potlining (SPL) was described. On the basis of the laboratory investigations, the effects of influencing factors in froth flotation process, such as grain size, flotation agent dosage, pH value, pulp density, and dissolved components concentration, etc, were carefully studied. And the influence on environment of the process was also discussed. It was found that flotation separation can be used as an environment-friendly method for treatment of SPL residue. Carbon and other compounds (include cryolite, sodium fluoride, calcium fluoride and diaoyudaonite, etc.) from SPL were separated and recycled as flotation products respectively.

Jan 1, 2009

By William A. Apel

Several different strains of bacteria have been shown capable of reducing hexavalent chromium, Cr(VI), to Cr(III), a less toxic, .. more readily recoverable form of Cr. This paper examined the Cr(VI) reduction efficacies of 3 different Cr(VI) reducing bacteria: Pseudomonas f1uorescens LB300., Pseudomonas aeruginosa PAOI, and Pseudomonas aeruginosa PAOI (pCROI) It was demonstrated that all three bacterial stratns reduced Cr(VI) primarily during their exponential growth phases while using glucose as their carbon and energy source. Significant differences in the three organisms' Cr(Vl) reduction capabilities depending on initial Cr(VI) concentrations were also demonstrated. P. aeruginosa PAOI showed superior Cr(VI) reducing capabilities over the. entire range of Cr(VI) concentrations tested while the Cr(VI) reduction capabilities of the other two strains were increasingly inhibited as Cr(VI) concentrations increased.

Jan 1, 1991

By Buket Tunçer, Mehmet Buğdaycı, Onuralp Yücel

ZrB2 and TiB2 are one of the most significant metal borides. They are being used in various industrial areas from space technology to nuclear industry owing to their physical properties such as high melting point, high thermal/electrical conductivity and low density. Present study was conducted in two main stages: Self-propagating high-temperature synthesis (SHS) reactions and leaching. ZrO2, TiO2, B2O3 were used as starting material and Mg used as a reductant to produce ZrB2-TiB2 powders via SHS. Therefore, it was aimed to determine production parameters, leaching conditions and comprehensive examination of final product features. The samples were characterized by using chemical analysis (AAS), XRD, XRF and SEM/EDS techniques

Jan 1, 2015

By M. Barkhudarov

The results are presented of research aimed at validation and development of a general purpose CFD code FLOW-3D. FLOW-3D is a commercial code developed by FLOW SCIENCE, INC. A number of physical modeling experiments involving the filling of cavities of different geometries with coloured water have been performed in order to compare the measurements with the results of computer simulations. Other numerical calculations were also done to be compared with the known analytical solutions.

Jan 1, 1992

By Nobuo Takahashi

Effective solvent extraction media have been investigated for purification of rare earths. At first, a quaternary ammonium compound was studied. The counter anions of rare earths and organic dielectric substances were tested to improve separation factors,. And second, crown ethers were selected for extractant. Several diluents of crown-adducts were tested to improve solubility and distribution coefficient as well as the counter anions of rare earths. Especially, in the presence of strong reducing agents, highly selective extraction of europium from other rare earths was observed. The third extactnts were ß -diketones. Presence of organic dielectric substances was very effective to improve separation factors. Though those. three groups of extractants were suitable for mutual separation of light rare earths, alkyl esters of alkyl-phosphonic acids were suitable for mutual separation of heavy rare earths because of their high separation factors. To keep proper pH value was necessary for acidic extractants, so control method of the solution pH was studied with high molecule insoluble amines or salts of those.

Jan 1, 1995

By J. David Chapman

There are a variety of choices of materials for mineral extraction processing. Traditionally, end users have used metallic piping for fluid handling and little is known about the advantages (or limitations) of non-metallic piping systems. This presentation will review custom FRP pipe systems and their use in severe corrosive and erosive process streams. These systems can be designed to various pressure and temperature ratings and different components (such as resin and glass type) can be varied to suit the process conditions

By C. J. Newman

The Kidd Creek Copper Smelter has been expanded from its original design of 59,000 tonnes of copper per year to over 120,000 tonnes per year. Modifications to the process gas handling system and acid plant have been made to accommodate this higher production rate and to generally optimize the operation. The gas handling system associated with the continuous smelting process is discussed in terms of boiler accretions and modifications to minimize their impact on operations; design changes to effect reductions in high pressure drop duct configurations; material changes to overcome corrosion and plant additions to improve gas cleaning capability. The acid plant is reviewed with references to changes? made to accommodate the increased SO2 gas strength resulting from the higher smelting rates.

Jan 1, 1992