Search Documents

By Jun Li, Lin Chen, Tian-zu Yang, Wei-feng Liu, Wan-da Bin

"The Chinese bismuth production accounts for more than 80% all over the world in 2011. The main raw materials of bismuth smelting are bismuth concentrate and by-products of Cu or Pb smelting process. Many traditional methods of bismuth smelting in china was reviewed in this paper, such as reverberating furnace smelting, blast furnace smelting, fire-refining, ferric chloride leaching-hydrolysis, slurry electrolysis, and so on. But all the traditional pyrometallurgy or hydrometallurgy process have such shortages of low recovery, poor environment, and high cost. Therefore new technologies are introduced into the smelting process of bismuth concentrate, such as low-temperature alkaline smelting and side-blown bath smelting with oxygen-enrichment. These technologies have got great progress on energy saving, emission reduction, and friendly environment. Finally the development direction of new technology on bismuth smelting was prospected.IntroductionAs a green metal, bismuth has a wider applications, just extending from the traditional medicine, metallurgical-chemical engineering, low-melting alloys, solders, catalyst, and electronics to cosmetics, flame retardant, storage battery, semiconductor, supper conductor and nuclear energy etc[1,2,3,4,5,6,7]. This will increase the production of bismuth and promote the development and progress of bismuth smelting technology. At present, The major bismuth-product countries are China, Mexico, Peru, KZ, Bolivia and Canada etc, and China are dominating. A survey from the USGS[8] showed that Chinese bismuth production were 12,500 tonnes and got 80% of the world's in 2011. Thus the technology of Chinese bismuth smelting have a great representativeness."

Jan 1, 2013

By Thomas Schuman, Jaan Kers, Lucas N. W. Damoah, Xiangjun Zuo, Lifeng Zhang

"Rapid technological innovation has propelled the use of electronic equipment leading to the generation of more and more waste electrical and electronic equipments (WEEE). Printed wiring board (PWB) is a component made of one or more layers of insulating material with electrical conductors. To investigate an environmentally friendly process to recycle PWBs, PWB samples with and without additives were pyrolyzed. Liquid, gas and solid products were achieved with different conversion fraction. Analysis of the exhaust gases from the experiments using GC-MS and MS showed that without CaCO3 additives poisonous gases such as C6H6 and HBr were produced which were adequately controlled if CaCO3 was added.IntroductionPyrolysis is one of the best methods for treating complex mixtures of waste polymers and to recover the material and energy content. The process consists of thermal decomposition at moderate temperatures in total absence or small amount of oxygen in which the structures of polymers break down into smaller intermediate products "". The decomposition temperature of a substance is the temperature at which the substance breaks up into smaller substances or into its constituent atoms 2). Thermal treatment of PWBs were reported using DC Arc Plasma furnace 3), and fixed bed reactor 4). One drawback in dealing with thermal treatment of PWB scraps is the likely production of super-toxic halogenated dibenzodioxins and dibenzofurans from the bromine containing structures. Pyrolysis of organic materials contained in waste PWBs leads to the formation of gases, oils, and chars which can be used as chemical feedstock or fuels ""'. Dehalogenation of the pyrolysis product of electronic scraps is essential to make it commercially acceptable. It would be obviously the most advantageous solution as pyrolysis and dehalogenation are carried out simultaneously. Reported pyrolysis investigations are at experimental stage and have been carried out in vacuum, molten salt, fluidized bed, rotary kiln, entrained, stationary, and moving bed reactors 7). Comparing to the incineration and combustion of PWBs, the pyrolysis process has several characteristics: 8'"">) 1). Converting the organic solid substance into fuel gas, fuel oil and carbon-black as storage energy; 2) Emitting toxic substances such as sulfur, bromine and heavy metals in wastes; and 3) Keeping metals from being oxidized. Although many researches into the pyrolysis of PWB wastes have been reported, most of the works have been carried out using analytical pyrolysis techniques or very small batch reactors ""~'5). Also, most of the works for the pyrolysis of PWBs haves concentrated on the composition of the organic products, particularly the brominated organics. The current study is to investigate the pyrolysis of PWB powders in a small TG-DTA scale and a 50-gram tube furnace scale."

Jan 1, 2011

By K. R. Robilliard

An outline is given of the problems facing tlile lead and zinc industry from the viewpoint of the range of residues currently produced from electrolytic zinc, blast furnace and other processes. Smelting approaches available using top submerged lancing technology are discussed and analysed. Pilot plant results for a range of lead and zinc-bearing materials are presented.

Jan 1, 1992

By Nathaniel R. Quick

"Nd: YAG, KrF excimer, and Cu-vapor lasers are used in air to synthesize conductors and semiconductors as a second phase in silicon carbide and aluminum nitride. Conductor resistivities as low as 104 O-cm are formed in these substrates; the resistivities for the untreated substrates range from 10 11to 1014 O-cm. The silicon carbide conversion is relatively independent of wavelength while the aluminum nitride conversion shows a dependence on wavelength over the range 248 nm to 1064 nm. Silicon carbide conductors, evaluated over the range 15 K to greater than 300 K, exhibit metal like conductivity; resistivity increases with temperature. Silicon, carbon, and oxygen are identified as the principal chemical species associated with the conductor in SiC substrates while aluminum, nitrogen, and oxygen are identified as the principal chemical species associated with the conductor in aluminum nitride substrates. The silicon carbide system, which has the less complex phase diagram, is evaluated in more depth to explain the synthesis mechanism. Oxygen was principally on the surface and increasing SiC conductivity is associated with decreasing spacing between 5 µm, or less, diameter carbon globules. This technology is proposed as a replacement for metallization in electronic packages, sensors and devices. INTRODUCTIONCeramics are commonly used for multichip module, hybrid and multilayer electronic packaging; semiconductor device and sensor applications because of the insulating, conducting, semiconducting, or superconducting properties that these materials possess (1,2) The majority of ceramics, however, have not been known to exhibit conductive or semi conductive properties when exposed to rapid thermal heat processing. A ceramic and process which through selective conversion can combine two or more of these electrical properties to eliminate the need for metallization is of interest to both the commercial and military sectors."

Jan 1, 1994

By C. A. Nogueira, F. Margarido

"A research work has being carried out annmg at evaluating the possibility of treating simultaneously several electrochemical systems of spent batteries using the same process, in order to overcome the high costs and difficulties of selective collection and sorting. Zn-Mn02 systems, representing more than 75% of portable battery market, shall be treated in dedicated processes. The treatment assessment using a single hydrometallurgical process of the other major systems (NiCd, NiMH and Li-ion), having Ni and Co as main metals, was the aim of the research work here reported. Sulfuric acid leaching was demonstrated to be adequate for dissolving more than 90% of the metals of interest contained in batteries. The subsequent separation of metals by solvent extraction, using organophosphorous extractants like DEHPA and Cyanex 272, allowed the production of pure solutions of rare earths, cadmium/manganese, cobalt, nickel and lithium, enabling their further recovering.IntroductionRecycling is the best approach for end-of-life management of spent batteries mainly by environmental reasons but also motivated by resources conservation and, in some cases, by economic profits. Most relevant electrochemical systems of portable cells are Zn-Mn02 (ZMB, alkaline and saline), nickel-cadmium (NiCd), nickel-metal hydride (NiMH) and lithium-ion (LIB). These batteries are collected, sorted and usually treated separately, applying for pyrometallurgical or hydrometallurgical technologies, the former being the most common.Several processes have been developed and some of them industrially applied, as described in some available review papers [l, 2]. In Europe for ZMB systems the oldest processes are Batrec [3] and Citron [4]. Although having differences in details, both are based on pyrometallurgical recovery of zinc by distillation, in metallic or oxide forms, being manganese retained in the slag together with iron. Hydrometallurgical alternatives are also available, like Zincex [5] and Recupyl [ 6] processes, both using sulfuric acid solutions as leachant. The application of the existing technologies to battery recycling, instead of using dedicated processes, is other alternative already tested, being the Waeltz furnace or the Imperial Smelting some examples."

Jan 1, 2012

By Isabella Lancellotti, Fabrizio Passarini, Luisa Barbieri, Fernanda Andreola, Ivano Vassura, Luciano Morselli

"The techniques able to incorporate wastes by means of a heat treatment present the advantage to fix the residue with chemical bonds. Among these techniques there are vitrification and sintering which are characterised by different operating temperatures in the range of 950-1500°C and the involved raw materials develop silicatic crystalline phases and glassy matrices capable to immobilize heavy metal contents in the waste matrix. In this work incinerator bottom ash, polishing and glazing ceramic sludges have undergone to thermal treatments in order to valorise the waste as secondary raw material for the obtainment of re-products. The chemical efficiency of the process adopted has been evaluated by comparing the results of release tests applied to the as-received wastes and to the thermally treated materials in order to verify the effectiveness of the different matrices to fix the waste components.IntroductionVitrification is one of the most promising technological options for the treatment of some kinds of waste. The high temperature involved in the process (1200-1500°C) leads to the complete destruction of organic pollutants, such as dioxins, and glassy network formed can incorporate heavy metals. Some vitrification processes naturally occur: glasses produced by volcanic eruptions, such as obsidians (Na2O-K2O-Al2O3-SiO2) and basaltic (CaO-MgO-Al2O3-SiO2) rocks, are basically inert materials even when they contain toxic elements, because these are embedded in an extremely stable glassy matrix. The disadvantage of vitrification is that it is an energy-intensive process involving relatively high costs, therefore its use is better justified if a high-quality product with optimised properties can be fabricated. The most effective way to improve the properties of the vitrified material is the transformation into glass ceramic. This is a fine-grained polycrystalline material (typically from 50% to 98% of the volume may be crystalline) formed when a glass of suitable composition is heat treated and hence undergone to controlled crystallisation (phenomenon named devitrification). The three key variables in the design of a glass-ceramic are: glass composition which controls glass viscosity related to the effectiveness of nucleation and rapidity of crystallisation; glass-ceramic phase assemblage (that is, the types of crystals and the proportion of crystals to glass) which is responsible for many of the physical and chemical properties; nature of the crystalline microstructure (crystal size and morphology and the textural relationship among the crystals and glass) which is the key to many mechanical and optical properties. In particular, a partly crystalline material can be obtained by powder sintering."

Jan 1, 2008

By Zengjie Wang

Investigation on hydrochloric acid leaching of the ilmenite from Panzhihua, China was carried out to prepare synthetic rutile. The leaching parameters were optimized to obtain high content of TiO2 in the products. The experimental data suggest that an optimum leaching can be realized with 30% acid, a solid/liquid ratio of 1/4 at 95°C for 4h, and ore ground for -400 mesh size. After the acid leaching, an additional alkaline leaching process using hot NaOH solution was performed, and then the products was in grain form followed by heat treated at 900°C for 2h in order to extract Si and increase the particle size of synthetic rutile. The final product has a high content of TiO2 (about 95%), a low content of chlorine consuming elements (total CaO+MgO =0.07%) and a suitable particle size distribution for chlorination process.

Jan 1, 2008

By Joel A. Huffinan

"This presentation is being given to better inform the audience of the dependability of precious metal analysis by fire assay. A brief explanation, however, of standard fire assay exploration procedures will be given. An overview of other types of analyses by fire assay will be discussed as well, and the operation of a modern day assay laboratory.IntroductionThe use of lead oxide for the fire assay process dates back to the finds in Troy II and the Cappadocian Tablets about 3,000 B.C. Some advances have been made in the basic procedures due to instrumentation and electronics, but the fusion and cupellation procedures used in fire assay remain much the same as during this period.In 1600 AD. Agricola was the first to take a scientific approach to fire assay recording methods and procedures used (Hillerbrand and Allen, 1905) [1]. Since this period, much of the recognized research into the analysis of ores and metals was carried out in the late 1800's and early 1900's prior to World War II, and again after the deregulation of precious metals. The renewed interest in precious metals mining and metallurgy are due much to advances in precious metals heap leaching in late 1970's."

Jan 1, 1999

By A. S. Block-Bolten

Two innovations in nickel-arsenic separation have been studied on a laboratory scale. The first requires only a nitric acid atmospheric leach without preliminary roasting and leads to favorable final conditions for precipitation of arsenic as highly stable FeAsO4, The second is an NaOH-H2O2 pressure leach which is an alternative to the known NaOH-O2 pressure leach. Either method offers the possibility of rapid and efficient separation of nickel from arsenic and is applicable, for example to the high grade niccolite deposits in the Great Slave Lake area of northern Canada.

Jan 1, 1982

By Musa Karakus

Ceramic build-ups are synthetic mineral deposits formed in critical locations in or near the throats of inductor units in channel induction furnaces, the preferred melting and holding furnaces used in iron foundries. The build-ups are undesirable because they slow down melt circulation, increase power consumption and cost. and decrease the quality of the metal. This study involved the determination of the mineralogy of build-up samples and the quantitative measurement of phase abundance in those build-ups by cathodoluminescence microscopy. These undesirable deposits usually are hard and dense and contain variable amounts of entrained metallic iron. The non-metallic phases dominantly consist of oxides and silicates of several refractory elements, AI, Mg. Ca, Si, and Fe. Minor amounts of the sulfides of Ca. Mg, Fe and REE elements, especially Ce and La. and the oxides and silicates of Ce and La elements are locally present in the build-ups. The build-up samples were found to be ideally suited for study by cathodoluminescence, which has provided an easy means for rapid re-cognition of the phases present in the build-ups. The phase compositions were determined by electron microprobe analysis. The phases identified and their characteristic cathodoluminescence shown in the ceramic build-up samples were: spinel (bright green, blue-green, and red). forsterite (red and purple), periclase (dark reddish-brown, blue. and orange), corundum (red, blue, orange, and white), anorthite (yellow, yellow-green, blue, and blue-purple), hibonite or calcium hexaluminate (dark green), mullite (dull red-brown), gehlenite (deep blue), silica(dark brown, pink, purple, red. and blue), monticellite (light violet blue and light pale yellow-orange), silicon carbide (orange), oldhamite (bright yellow and orange). Ce-La silicate phases (purple), and glass (orange, dull red, and purple). Non-luminescent phases were: hercynite, Fe-oxides, Ce-La-oxides, Fe-sulfides, and metallic iron.

Jan 1, 1989

By Toshihiko Emi

The quest for cleaner steel is driven by increasingly stringent requirements from the manufacturing and construction industries. Key issues are the occurrence and removal of inclusions; These are discussed in the context of the unit processes of deoxidation, refining, transfer and casting of molten steel. Process thermodynamics and kinetics are also discussed. Recent progresses achieved and problems yet to be solved are elaborated, and an integration of the unit processes into a system to produce extra clean, steels with better performance is presented.

Jan 1, 1999

By M. H. Erten

Most of the fourteen workable coal seams in the State of Missouri have high ash and sulfur levels and need beneficiation in order to meet customer and Environmental Protection Agency requirements. If proper ash and sulfur removal methods can be designed, more Missouri coals will be mined and used within the state. One of the main objectives of this research is to investigate the possibility of removal of sulfur of Missouri coals by conventional beneficiation methods.

Jan 1, 1982

By Won C. Park

Experiments showed changes in the mineral content of dolomitic oil shale at temperatures and exposure times which bracket conditions encountered during in situ retorting. Laboratory results correlate with cores from a spent in situ retort at Occidental's Logan Wash test site at Garfield County, Colorado. Dolomite, CaMg(CO3)2, decomposes rapidly to form periclase, MgO, calcite, CaCO3, and CO . Both calcite and periclase are intermediate products that can be stabilized by CO atmosphere at lower temperatures, while steam accelerates the formation 2 of silicates. The decarbonation of calcite appears to involve a direct reaction with both quartz and periclase in forming these silicates. Decarbonation preceeds the formation of akermanite, Ca2 MgSi 207, and diopside, CaMgSi 206, within several hours of heating and is followed by the nucleation of forsterite Mg2SiO4, and monticellite, CaMgSiO4. Under in situ retorting conditions, akermanite and diposide are the major minerals above 800°C. Equilibrium is not attained within 200-300 hours. In situ retorting temperatures above 800°C for extended periods of time should reduce potential ground water leaching by the formation of silicate minerals. These silicates are less soluble than free lime, magnesium or alkali oxides. There is a corresponding decrease in the natural pH of these silicates from approximately 12 down to 7.5 to 9:

Jan 1, 1981

By Fiona J. Stevens McFadden, Gregory J. Hardie, Mark P. Taylor, William Uru

"Over 20 million tonnes of installed aluminium smelting capacity exists worldwide, with smelter energy con.sumption in the range 14-17 kWh/kg aluminium. In terms of the reduction cell technology itself, the lowest sustained energy consumption is just below 13DC kWh/kg, or 50% energy efficient.For 15 years Comalco Aluminium Ltd. in Australia has been engaged in developing and testing reduction cells that use a refractory hard cathode, composed of a TiBif carbon composite coating over a carbon cathode. This technology has the potential to reduce energy consumption significantly while simultaneously increasing the life of the cells, which is currently limited by wear rate of the conventional carbon cathodes used throughout the worldIntroductionThe successful development of an aluminium wettable cathode technology affords the opportunity to the cell designer and smelter operator to fundamentally change the physical operating characteristics of the Hall-Heroult process. With this revolutionary capability in hand, published papers and patents have indicated that the technology may be exploited in a wide variety of ways to improve the economic performance of aluminium smelting process. Comalco has been developing refractory hard cathode technology for more than 15 years and has been exploring a number of ways that the technology may be commercially applied in a smelter operation [l]."

Jan 1, 2000

By Anja Pfennig, Axel Kranzmann, Sabrina Schulze

The CCS technique involves the compression of emission gasses in deep geological layers. To guarantee the safety of the site, C02-corrosion of the injection pipe steels has to be given special attention when engineering CCS-sites. To get to know the corrosion behaviour samples of the heat treated steel 1.7225 42CrMo4, used for casing, and the stainless injectionpipe steel 1.4034 X46Cr13 were kept at T=60 °C and ambient pressure as well as p=lOO bar for 700 h - 8000 h in a C02-saturated synthetic aquifer environment similar to possible geological on-shore CCS-sites in the northern German Basin. The isothermal corrosion behaviour obtained by mass gain of the steels in the gas phase, the liquid phase and the intermediate phase gives surface corrosion rates around 0.1 to 0.8 mm/year at ambient pressure and much lower about 0.02 to 0.2 mm/year at 100 bar where the C02 is in its supercritical state. Severe pit corrosion with pit heights around 4.5 mm are only located on the 42CrMo4 steel. Main phase of the continuous complicated multi-layered carbonate/oxide structure is siderite F eC03 in both types of steel.

Jan 1, 2013

By Donald Voit

"The reaction between zirconia/zircon, coke, and chlorine involves a slow reaction between the coke and the zirconia/zircon and a fast reaction with chlorine. Because of the fast chlorine reaction, the reaction rate for zirconia/zircon is nearly independent of chlorine concentration for most conditions. The reaction between zirconia/zircon and coke is particle size controlled and related to the degree of physical contact between the zirconia/zircon and the coke. Since particle-particle contact is critical, compaction of finely ground coke and zirconia/zircon produces the highest reaction rates. Uncompacted, coarse coke and zirconia/zircon has the slowest reaction behavior with static bed tests.SummaryZirconia reacts with chlorine in the presence of carbon to form zirconium tetrachloride, carbon monoxide, and carbon dioxide. A similar reaction occurs with zirconium silicate with the additional formation of silicon tetrachloride. The reaction rate depends primarily on temperature and the intimacy of contact between the zirconia and the coke. The reaction is multi-stepped with a slow reaction between coke and zirconia to form an intermediate that reacts rapidly with chlorine, causing the order of the reaction for chlorine to be near zero. Chlorination rates in the range of 1 µmole/hr/cm2 are seen for fluid bed reactors. Plug flow, and static bed reactors have reaction rates of the order of 1 mmole/hr/cm2, where the area is based on the zircon surface area in plug flow and fluid bed reactors and the boat cross sectional area in a static bed. Chlorination rates measured in zirconia/coke briquettes are higher with rates as high as 400 mmole/hr/cm2 reported. High chlorine diffusion resistance, not accounted for in the analysis of experimental results, has led to a lot of confusion in the literature interpretation of chlorination data.In general coke and zirconia/zircon particle size, coke and zirconia/zircon intimacy, coke to zirconia/zircon ratio, chlorine concentration, and temperature are important variables for chlorination. Decreasing the coke and zirconia/zircon particle size generally increase the reaction rate. The coke to zirconia/zircon ratio affects the reaction in a more complex way. Increasing the chlorine concentration generally increases the reaction rate, but the effect appears to be more related to the concentration dependency of diffusion than to its role in the kinetics. The reaction rate increases with temperature but the exact behavior is complicated by temperature effects on diffusion."

Jan 1, 2011

By Payman Roonasi

Having knowledge of mechanism of magnetite formation is essential in a number of industrial processes including magnetite synthesis and corrosion of iron. In this study, magnetite nanoparticle was synthesized via two different ways; coprecipitation of iron (II) and (III) and oxidation of ferrous hydroxide. The samples were characterized using X-ray diffraction (XRD), Mid-Far IR spectroscopy, scanning electron microscopy (SEM), chemical analysis for determination of Fe II/Fe III ratio and ICP-MS for iron isotopic ratio (56Fe/54Fe) measurement. Since fractionation of iron isotopes depends on reaction rate and bonding strength, interpretation of the isotopic data with respect to the possible mechanisms is discussed. No fractionation of iron isotopes was observed for the magnetite synthesized by coprecipitation, whilst magnetite formed from ferrous hydroxide showed higher abundance of 54Fe compared to 56Fe in the beginning of reaction, implying the significance of the following reaction:

Jan 1, 2009

By R. C. Nascimento

It was investigated the effect of the addition of bentonite on the physical propertiesof pellets produced from fines of manganese ores. Cold-bonded pellets were produced. Pellets bearing up to 1 wt% of bentonite were submitted to strength compression resistance tests, fatigue of pellets to impact and maximum height of fall tests. A correlation of resistance of the pellets and time for curing were stablished. The produced pellets match the conditions for raw materials used in electric smelting hrnaces to produce manganese based ferro-alloys.

Jan 1, 1995

By A. Gibson

Most methods for the treatment of scrap printed circuit boards do not reclaim the components in working order as the boards are either fed to a copper smelter, to recover the valuable elements, or, simply landfilled. This work reports the dissolution of the solder in fluoroboric acid containing Ti4+ ions which was particularly selective for solder, allowing the components to be recovered. The solder was subsequently electrowon from the leachant. The boards were then shredded and the copper dissolved in ammonium sulfate and, then treated via solvent extraction to give an electrolyte suitable for electrowinning. The remainder of the metals were dissolved aqua regia, silver remained unattacked by the aqua regia, palladium precipitated as Pd(NH4)Cl6 in the presence of zinc and nickel, the gold was removed by solvent extraction and precipitated as nanoparticles. The aqua regia was then diluted and the zinc and nickel separated by solvent extraction.

Jan 1, 2009

By Lincoln McCrabb

Correct measurement and interpretation of viscosity data is critical for design of any thickening and pumping process that involves a non Newtonian slurry. The nickel laterite pressure acid leach (PAL) process relies on producing a slurry of maximum achievable solids concentration. Small variations of 1-2% solids concentration can alter economics significantly. For the Ravensthorpe Nickel Project, a rheology protocol has been developed which optimizes the solids concentration across a range of ore types. The vane yield stress technique has been utilized to accurately quantify the flow of thickened slurry in the lower shear range. A yield stress of 100Pa has been used as a benchmark to determine the optimum solids concentration achievable utilizing deep cone thickening. Statistical analysis of the data shows critical rheology distinctions between ore type, particle size, lithology and geochemistry. Linear and power law models have been applied to rheology flow curves to reconcile the material transport properties with the anticipated thickener underflow solids concentration. Keywords: Vane Yield Stress, Thickening, Rheograms

Jan 1, 2004