Search Documents

By David Melgaard

A significant emerging recycling, waste minimization problem stems from legacy waste from the nuclear weapons program and from production of power using nuclear fuel. Premium quality metals used in nuclear plants become contaminated, making them unsuitable for reuse. Consequently, decontamination studies were conducted to evaluate the decontamination capacity and partitioning effeetiveness of Electroslag Remelting (ESR). Eight laboratory melts were conducted to evaluate the efficacy of using ESR to transport radionuclides from the liquid metal phase to the liquid flux or slag phase. To determine the decontamination effectiveness, several surrogate compounds for uranium, plutonium and other fission products were added to the melts. During the melts, the melting rate was varied, typical slag additives were used, and two different slag compositions were evaluated. The resultant post-test ingots and slag were then analyzed to determine the partitioning of the surrogates. ESR generally proved very effective in removing contaminates from the metal with a few noted exceptions. -

Jan 1, 2003

By Ray D. Peterson, Annette Revet

The optimization of secondary aluminum furnaces is critical to the efficient operation of a recycling facility. Since all metal loss occurs in the drosses, physical and chemical analyses of these by-products are valuable diagnostic tools. Dross analyses can provide information concerning total furnace metal recovery efficiency as well as identifying areas for potential improvements. A complete dross analysis is a labor-intensive process that requires significant care both in sampling and performing the analytical techniques. Experiments can be done at a bench- or plant-scale depending on the facilities available. This paper outlines the benefits and information that can be generated through dross studies. Furthermore, several analytical methods are discussed as well as the special requirements needed to gain accurate results. Experimental data from industrial studies is provided to demonstrate the use of dross evaluations for ~ace optimization.

Jan 1, 2000

By Georgios Kolliopoulos

Water is a critical commodity of our generation and a key compound for the chemical and mining industries. Sustainable industrial development is directly associated with the ability to recover clean water from contaminated sources. Forward Osmosis (FO) is a low-energy footprint membrane process allowing the recovery of clean water from high salinity effluent streams. In FO, water is recovered spontaneously into a concentrated draw solution (CDS). Energy is required to separate the recovered water from the resulting dilute draw solution (DDS). In the current work, the fundamentals of the FO process and the most important aspects affecting its performance are discussed. An energy comparison of FO and conventional water recovery technologies is presented. Finally, the opportunities FO presents in the field of hydrometallurgy are analyzed.

By R. Burkhard

Recovery of metals from complex mixed wastes is a challenging task of modem material and waste management strategies. Thermal methods are an important tool in this respect. Plasma turned out to be particularly useful for treatment of complex or toxic wastes and residuals. In order to study plasma processes at reasonable costs, a pilot plasma plant has been used and wastes like ~pent Raney-Nickel catalysts, copper and ah.:lminum drosses, and. other metal containing wastes were investigated. The paper summarizes the most significant findings

Jan 1, 1995

By Matthew D. Andriese, Jiann-Yang Hwang, Zhiwei Peng

"It has been demonstrated that metallic-bearing minerals are physically liberated from host rock when exposed to microwave (MW) energy. The metallic minerals are iron sulfides and spinel oxide minerals contained in peridotite rock. Experimental evidence has shown ore particles readily couple with MW energy at 2.45 GHz, 1000 W resulting in rapid heating. Thermal stresses are generated by highly absorbing metallic-bearing minerals resulting in cracking and embrittlement of ore particles that assists in crushing and grinding processes. The liberated metallic-bearing minerals are shown to report to coarser size fractions as a result of MW exposure.IntroductionComminution of ore material during beneficiation is a large energy expenditure for the mineral processing industry. Crushing and grinding operations alone consume 50-70% amount of energy used in mineral processing [1]. Size reduction becomes increasingly difficult with decreasing particle size making grinding the most energy-intensive step of comminution. The aim of comminution is to maximize liberation of economically valuable minerals from the host rock [2]. Overall, the less material that needs to be handled, then grinded, to create a useful product for hydro/pyro metallurgical processes will achieve the greatest reduction of energy.Much of the scientific interest for use of microwave (MW) energy in mineral processing has been for improved hydro/pyro metallurgical techniques [3-6]. Early authors have employed MW energy for improved grinding of ore particles but most conclude the energy savings do not justify the energy input [7-9]. The effectiveness of MW assisted grinding is dependent on the ore mineralogy and the absorptive properties of minerals contained within it. Ore containing magnetic minerals should prove successful with MW assisted breakage from highly absorptive properties."

Jan 1, 2012

By C. Hennesmann, D. Maijer, S. L. Cockcroft, P. Yo

"Die cast aluminum wheels are one of the most difficult automotive castings to produce because of stringent cast surface and internal quality requirements. As part of a collaborative research agreement between researchers at the University of British Columbia and Canadian Auto Parts Toyota Incorporated, work has been underway to predict heat transport and porosity formation in die cast A356 wheels. The basic heat transfer equations have been solved using the commercial finite element package ABAQUS to which specialized routines have been added to predict porosity. Preliminary work on predicting porosity formation focused on using the Niyama parameter as a measure of the probability of porosity. The latest version of the model incorporates a new fundamentally based porosity criterion, which takes into account the effect of hydrogen concentration. The development of this model together with its application to a series of cylindrical test castings as well as a production cast wheel are presented.I. IntroductionDie cast aluminum wheels are one of the most difficult automotive castings to produce because of stringent cast surface and internal quality requirements. Microporosity, in particular, is a common defect that can adversely affect wheel quality. The mechanism of microporosity formation in aluminum alloys is complex owing to its dependence on the interaction of a number of phenomena occurring during solidification including the decrease in hydrogen solubility, the decrease in volume, the development of the solidification structure, and the increase in difficulty in interdendritic feeding [1]. As a result, the amount, size, and distribution of microporosity is affected by a large number of casting parameters including thermal variables, melt composition, grain structure, modification, and inclusion content, making optimization by trial-and-error methodologies difficult.The use of criteria functions, based on thermal conditions during casting, offers a relatively simple approach to predicting microporosity. In practical terms, they are useful because they provide a straightforward method of assessing the impact of varying casting parameters on porosity through various thermal parametersl21 such as thermal gradient, cooling rate, solidification time, and solidus velocity. Drawbacks of criteria functions include insensitivity to varying hydrogen concentration and the limitation to qualitative predictions. Consequently, in aluminum alloys, attempts have been made to develop models incorporating the effects of hydrogen gas and microstructure evolution. However, these types of models represent a significant increase in complexity and sacrifice the simplicity and ease of application of the thermally based criteria functions."

Jan 1, 2001

By Michael J. Nicol

Growing environmental and occupational safety concerns about the use of cyanide in gold processing has increased the interest in more acceptable alternatives. The most likely of these is thiosulfate. However, the thiosulfate process lacks a proven in-pulp method of recovering the dissolved gold, because activated carbon is not effective for the absorption of the gold thiosulfate complex .. Anion exchange resins do offer a possible route for in-pulp recovery. This paper describes work aimed at the evaluation of the effectiveness of commercially available anion exchange resins for the recovery of gold from thiosulfate leach liquors? and pulps. It has been found that strong-base resins are superior to weak-base resins in that they have a larger capacity, which assists in reducing the competition from other anions within a leach solution. Further studies with a selected commercial strong-base resin have shown that competing polythionateanions (particularly tri-and tetrathionate). Lower the maximum possible gold loading but that gold is selectively recovered over other base metal anions in solution. Kinetic experiments found that while? competilig anibns did not affect the initial rate? of gold loading it was important to minimise the contact time of the resin in solution so to prevent displacement of loaded gold by competing anions over longer times. A small-scale resin-in-pulp plant investigation showed gold can be recovered from a leach pulp by a strong-base resin to yield gold loadings of 3000 mg/L, barren pulp containing less than 0.05 mg/L of dissolved gold and. copper loadings of 500 mg/L. Loaded copper was displaced gold and at a loading of 2000 mg/L gold the copper loading was minimal «500 mg/L). The resin was found to recover gold adsorbed on the solids that would, otherwise have. reported to tails if a solid/liquid separation method were used. A patented two-step elution process in which copper and then gold are separately eluted from the resin is also discussed.

Jan 1, 1998

By B. Q. Li, H. C. de Groh, X. Lu

"A fully 3-D, transient finite element model is developed to represent the magnetic damping effects on complex fluid flow, heat transfer and electromagnetic field distributions in a metallic melt. The model development is based on our in-house finite element code for the fluid flow, heat transfer and electromagnetic field calculations. The numerical model is tested against numerical and experimental results for water as reported in literature. Various numerical simulations are carried out for the melt convection and temperature distribution with and without the presence of a transverse magnetic field. Numerical results show that magnetic damping can be effectively applied to stabilize melt flow, reduce turbulence and flow levels in the melt and over a certain threshold value a higher magnetic field resulted in a greater reduction in velocity. Also, for the study of melt flow instability, a long enough running time is needed to ensure the final fluid flow recirculation pattern. Moreover, numerical results suggest that there seems to exist a threshold value of applied magnetic field, above which magnetic damping becomes possible and below which the convection in the melt is actually enhanced.1. INTRODUCTIONThe imposition of a DC magnetic field on a moving, electrically conducting fluid, such as molten metal or semiconductor melt, produces an opposing Lorentz force that results in a reduction of flow velocity in the liquid. This effect has been explored in both the semiconductor and metals industries to control natural convection and/or surface tension induced Marangoni convection as well as thermally induced flow instability during solidification processing of these melts [1-6]. A mathematical model can be of great use in developing both fundamental understanding of the fluid-magnetic field interactions in these magnetically-assisted processing systems and basic guidelines for process design, control and optimization.This paper presents a 3-D mathematical model for magnetically damped fluid flow and heat transfer in a melt cavity, which is useful for interpreting results for unidirectional solidification processes at slow solidification rate, and some preliminary results concerning the magnetic damping effects on the flow instability in the melt. The model development is based on the finite element solution of the Navier-Stokes equations, energy equations and equations for induced electric field. The model is tested against reported results and is then applied to study the fluid flow and thermal distribution in the metallic melt with and without an external magnetic field."

Jan 1, 1999

By Ari I. Kogut

Impurity minerals in fluorspar ores and concentrates from a deposit in Southern Africa have been studied by reflected light, transmitted light, and cathodoluminescence microscopy. The principal impurities are quartz, calcite, aegirine, apatite, ankerite, magnetite, goethite, and synchysite [Ca(La,Ce,Nd)(C03l2Fj. Cathodoluminescence microscopy was found to be very useful in studying the character of the fluorite and especially for recognizing the presence of apatite and calcite impurities. Fluorite exhibits blue, calcite shows yellow, and apatite has white, light purple, and pink cathodoluminescence. The cathodoluminescent character of apatite varies with its geological environment and position in the orebody. The results of this microscopic study show that phosphorus present in flUorite concentrates occurs principally in binary locked apatite-fluorite particles. Successive fluorite cleaner concentrates contain progressively smaller amounts of locked apatite-fluorite particles. Free apatite has been effectively partitioned to the final tailings.

Jan 1, 1995

By Jewel A. Gomes

Keywords: Electrocoagulation, arsenic removal, fuel cell, windmill, energy simulation, combined Fe-Al electrode assembly Arsenic contamination of well-water in different countries has caused signs and symptoms of arsenic poisoning. Although several physicochemical treatments are presently used for the removal of arsenic compounds from drinking water, an electrochemical treatment, electrocoagulation, is a promising processing technology and currently is the most efficient (above 99% removal) and environmentally friendly technique, particularly if combined with alternative energy sources. Wind and fuel cell technologies can be considered the most promising developmental clean power sources. We will discuss new insights into the materials processing mechanisms and show the coupling of electrocoagulation with fuel cells and simulated wind energy sources. Different electrocoagulation plate materials were considered, along varied currents from the fuel cell to produce maximum arsenic removal. Coupling these technologies will remove carcinogenic arsenic from water sources, and will exhibit efficient usage of these energy sources by producing pure water for human and agricultural consumption.

Jan 1, 2005

By Shantaliu S. Shevade, Muhammad M. Rahman

"This paper presents a systematic analysis of fluid flow and heat transfer processes during the magnetic heating of the substrate material. Heat is generated in the substrate material when a magnetic field is imposed due to change in orientation of the molecules. As a result, the substrate temperature rises. The i;tudy considered microchannels with rectangular and square cross section with heat generation in the substrate due to imposed magnetic field. The results computed were for Gadolinium substrate and water as the working fluid. The purpose of this study is to explore the transient heat transfer coefficient when the fluid is circulated through the substrate via microchannels. Equations governing the conservation of mass, momentum, and energy were solved in the fluid region. In the solid region, heat conduction was solved. From the simulation results, plots of Nusselt number and heat transfer coefficient were obtained over the length of the channel. A thorough investigation for velocity and temperature distributions was performed by varying channel aspect ratio, Reynolds number, and heat generation rate in the channel. It was found that the peripheral average heat transfer coefficient and Nusselt number is larger near the entrance and decreases downstream because of the development of the thermal boundary layer. With the increase in Reynolds number, the outlet temperature decreased and the average heat transfer coefficient increased.IntroductionMagnetocaloric effect (MCE) is the heating or cooling of the magnetic materials due to varying magnetic field. The effect was originally discovered by Warburg. Magnetocaloric materials store heat energy in the way the atoms vibrate and in the way electrons spin within each atom. More heat energy increases the vibrations and also makes the spins more random. When a strong magnetic field is applied to a magnetic material, the magnetic moments of its atoms become aligned making the system more ordered. The more ordered material has lower entropy and compensates for the loss by heating up. When the magnetic field is removed, the magnetic moments return to their random directions, entropy increases and the material cools. Gadolinium is a magnetic material that exhibits high temperature rise during adiabatic magnetization around its transition temperature of 295 K. It has been experimentally observed that adiabatic temperature rise increases with magnetic field strength and can be as high 20 K when a magnetic field of IO T is applied. Thus magnetic field, when applied to a microchannel heat exchanger, causes temperature change in the magnetic material. The fluid flowing through the channel gets cooled or heated due to this adiabatic temperature change."

Jan 1, 2004

By Messias dos Santos Machado, Renato B. Godoy, Roberta Lima, Andressa Silva, Francisco Valenzuela-Díaz, Rene R. Oliveira, Esperidiana Moura

This work aims to incorporate the Bof White Clay, from Boa Vista, Paraiba State, Brazil, as natural nanofiller in Ehylene vinyl alcohol copolymer (EVOH) and obtain flexible films. Nanocomposite was obtained using a twin-screw extruder, and film formed using a blow extruder machine. The flexible film nanocomposite was characterized, by tensile tests, XRD, DSC and their properties were evaluated. The results showed a good interaction between the clay and the EVOH resulting in an increase of properties of films nanocomposites as compared to films neat polymer.

Jan 1, 2015

By S. Moussa

The formation of boron-doped nickel aluminides Ni3AI, (76 at. % Ni) from elemental powders by reaction synthesis using reactive sintering was studied. The process involves the mixing of elemental powders of nickel and aluminium with various wt % of boron up to 1 wt % boron. Nickel and Aluminium powders were mixed in the correct proportion to form the intended boron-doped nickel aluminide intermetallic. XRD, SEMI EDS, Image analysis and Archimedes principle; were used to study the effect of Boron addition on the final microstructure, bulk density, average grain size of as reactively-sintered nickel aluminides (boron-doped), compared with no boron addition. The results showed that at greater boron content than 0.3 wt %, a two-phase non-equilibrium microstructure of consisting of NiAI phase in NiJAI matrix was formed that have been primarily retained even after heat treatment for 5 hours at 1000 °C. Boron was present in solid-solution within both the NiAI and the Ni3AI (in greater amounts) phases.

Jan 1, 2001

By B. L. Chulu

In the carbothermic reduction of lead sulfate to produce lead, the inclusion of soda ash (Na,CO,) in the charge provides for the control of sulfur dioxide in the effluent gas. An important mechanism in the process appears to be the carbothermic reduction of the sodium carbonate whereby sodium gas and carbon monoxide are produced. These intermediates then participate in the reduction of the lead sulfate to produce lead metal and stable sulfur species in the molten slag phase. In addition, there is some evidence that the presence of lead metal in the charge may also serve to increase the lead recovery in the process. These aspects were investigated by conducting laboratory-scale smelting tests with small charges (;3g), at 1173°K(9000C). Recovery did not exceed 74w% and the role of incipient lead metal in the charge could not be clearly assessed.

Jan 1, 1993

By Wang Shuchan, Zhang Zimu, Zhang Dianhua, Liu Yan, Zhang Ting-an, Zhao Qiuyue, Lv Chao

Rare earth extraction tank has many adverse effects like big floor space and high production accumulation during industrial production. Current researches usually focus on changing the device structure without making a breakthrough towards gravity clarification. This paper attempts to achieve this goal by using both the action of clarification by gravity and clarification by stirring. Because many physical parameters affect the clarification and separation rates, the density, viscosity and surface tension of the two phases were determined at different temperatures and different concentration of aqueous solution. The innovation of this research involves adopting the Karl-Fischer method to investigate water content in oil phase during the stirred separation process. In this paper, the separation effect of different physical parameters was studied and the dimensional equation between water content and the physical parameters was established by combining with the experimental data.

Jan 1, 2014

By A. Raraz

The optimization of the plutonium electrorefining process has been studied on the basis of modeling and model materials. The plutonium electrorefining process has been reviewed and the basics of the electrorefining process with molten salts as electrolytes and under forced convection has been presented. The definition of the problem in plutonium electrorefining has been related to three factors and this research has addressed these three factors to provide an insight to this process. The hydrodynamic factor gives information on the behavior of the mechanically stirred system. The chemical stability and solidification factor shows the interactions among the components of the electrorefining cell. The electrochemical factor is oriented to study the efficiency of the electrorefining process on the basis of limiting current density, stirring rate and configuration cell. As a result of this study the optimization of plutonium electrorefining implies mainly a re-design of the cell.

Jan 1, 1995

By Mark Jolly, Xiaojun Dai

"Foundry engineers in the traditional foundry usually regard the quality of casting component as the most important issue and leave the energy saving or energy efficiency as the subsidiary one. This frequently causes disproportionate energy consumption as a result of the inefficient casting processes used and increases the production costs. This paper presents the novel CRIMSON aluminium casting process and compares its facility and melting process with traditional melt furnaces and aluminium alloy melting process. A real example is investigated to demonstrate quantitatively how the traditional foundry wastes energy and what the improvement of energy efficiency can be achieved using the new CRIMSON method. The results of this investigation will help the foundry engineer recognize the importance of energy saving and demonstrate how to use this new technology to reduce production costs and carbon footprint without decreasing the quality of the cast component.IntroductionAluminium melting in metal casting industry is an energy intensive process where it is estimated that the energy consumption is in the order of 1,700 ~ 4,700 kWh tonne-1 in using crucible and natural gas [1]. Different countries may use different energy resources for aluminium melting: in US the main energy resources are natural gas, electricity and coke [2] and in UK most of the foundry use electricity, gas and oil as energy resources [3]. Due to the pressure of rising energy price and the strict environment law, it is anticipated that under the right socioeconomic conditions, the efficiency optimisation of industrial process can be an important step toward increased industrial sustainability [4]. In metal casting industry the energy efficiency of a casting facility depends largely on the efficiency of its melting and heat treating performance. In association with the two performances, over 60 % of the total process energy costs are represented in a typical casting facility [5] where there are huge opportunities for metal casting industry to adopt the best energy practices for potential energy saving. How to ameliorate the current processes for increasing energy efficiency will have a vital effect on reducing the production costs and increasing the competitiveness. For instance, by implementing some state of the art technologies such as the CRIMSON method in aluminium alloy casting will make use of such opportunities."

Jan 1, 2011

By M. Save, N. Menad

"This paper gives the overview of different alternatives to recycle the following wastes: slag, dusts, wastes of electric and electronic equipment (WEEE) and auto shredder residues (ASR). Based on modified Bogue calculations, steelmaking slags were combined in order to produce a belite-rich clinker activated with sulphoaluminate. The EAF dusts containing significant amount of metals can be recycled in different ways: The carbothermal treatment and INTECT process are reported. The results obtained from the model of Auto Shredder Residue injection into blast furnace show that ASR can be used as reducing agent in the BF process if certain conditions are met. The particle size of this material must be controlled to ensure optimal gasification of the material in raceway. The non-ferrous contents may affect the pig iron quality, which is difficult to rectify at a later point. It seems the pyrolysis is the most attractive process to handle ASR. The BRGM flow sheet of WEEE treatment is also reported.I. Introduction The activities of human been may generate wastes and by their accumulation during several years, these wastes may have an impact on the environment and on the human health. These wastes can be generated in the forms of solid, liquid and gas. A variety of industrial wastes can be recycled for use as products. There are three ways in which industrial waste recycling occurs: at the facility itself (on-site recycling), at commercial facilities that gather waste streams from several companies (off-site recycling), and at a company that uses as inputs in its production process the waste products of another company. The industries producing iron and steel may generate different solid wastes which are classified in three main categories: 1. Ferrous material (mainly dusts and sludges from gas cleaning), 2. Slags (these by-products are generated from different process stages), 3. Others by-products (including refractories and material generated from engineering activities). According to this review, the most quantity of the metallurgical wastes is deposed. Currently, the public opinion opposes the creation of new sites. This leads to the growth of the waste disposal costs. Such situation reduces the enterprise competitiveness and decreases their market share on regional and/or national and/or world scales. In these conditions, the economical activities can be decreased leading probably to social problems. The problem of wastes and/or by-products can be treated on three levels:"

Jan 1, 2008

By Denise Crocce Romano Espinosa, Andrea Moura Bemardes, Jorge Alberto Soares Tenorio, Daniella Cardoso Buzzi, Tatiana Scarazzato

"In copper plating processes, a fraction of raw materials are incorporated to the final products, while other portions are discarded as effluents. In this study, the application of electrodialysis (a membrane treatment process) was studied for treatment of wastewaters from cyanide-free strike baths, in order to reuse the components of this bath: copper and HEDP. The synthetic solutions studied consider 1 % of ion concentration of the bath used in this process, simulating the rinsing waters to be discarded. The electrodialysis allowed a percentage extraction up to 73% of copper ions and 72% of HEDP from the effluent. Complexes formation between the acid and copper indicates the possibility of recovery of components in the same compartment, obtaining a concentrated solution of these substances that can be reinserted in the process, for compensating drag-out losses. A diluted solution is also obtained, that can be reused as water in rinsing tanks.IntroductionIn metal finishing industries, contaminants in wastewater and the type of treatment required are determined according to the type of operation [l]. Generally, electroplating industries employ conventional wastewater treatments, e.g. oxidation of cyanide and chemical precipitation. This stage promotes reactions with soluble compounds to produce an insoluble precipitate, removed by physical separation. The sludge is dried by press-type filters [2].In this manufacturing sector, part of the raw materials are discarded as hazardous waste. The cost of discarded compounds and the treatment and disposal of waste may compromise profit margins. In addition, water consumption per unit of production stimulates the development of methods able to recover and reuse the largest possible amount of water [3].In some plating processes, cyanide-based substances are used as complexing agents and as raw materials in form of metal salts [4]. However, the toxicity associated with cyanide has been promoting research for the development of new raw materials in plating processes.A study conducted in Brazil [4] evaluated the modification of a commercial cyanide-free bath for processes of copper coating on Zamak. In the performed study, a new alkaline copper bath was formulated using l,hydroxyethane-1,1-diphosphonic acid (HEDP), an organic compound known for forming stable complexes with metal ions.As results of the study, the operational conditions and the formulation of a bath to obtain adherent, uniform and bright layers were established (Table I) [4]."

Jan 1, 2014

By Florian Kongoli

The overall productivity and efficiency of sulfide smelting plants depends considerably on the productivity and efficiency of each unit furnace operations. Furthermore, the efficiency and productivity of each furnace affects and dictates to a certain degree the process of managing the flow of materials from one unit to another. A furnace with low productivity, several technical problems or high frequency of accidental shut downs can easily become a temporary or a permanent bottle neck in the entire flowsheet and can be the cause for a low productivity and efficiency of the entire plant. As a result, controlling, optimizing and automating the individual furnace operations in order to assure a stable process but at the same time to increase productivity is an indispensable need. In this paper, the authors discuss their recent work in effectively controlling acute industrial furnace problems such as magnetite build-up and accretions, eliminating unnecessary slag foaming, decreasing slag losses etc. as well as the intensification, optimization and automation of a series of furnaces in sulfide smelting through a unique physical process modeling that correctly simulate the industrial furnace operations and avoid guessing and uncertainties. The advantages of this new approach have been discussed.

Jan 1, 2006