Search Documents

By Abbas H. Mirza

Arsenic and selenium are found in low quantities together with other metals in several nonferrous metallurgical process streams such as scrubber blowdown solution, acid plant wastewater, gas cleaning plant water, etc. Normally, the other metals in these streams are present as cations and can be precipitated by conventional lime treatment and sulfide polishing. However, arsenic and selenium are invariably present as anions, AsO33-and AsO43 in the case of arsenic and SeO32 and SeO42 for selenium. Conventional lime treatment removes most of the arsenic, but it does not remove selenium. The present paper reviews the processes and technologies developed to date on the removal of arsenic and selenium from metallurgical process streams.

Jan 1, 1996

By Tomoya Nihei, Hiroshi Hayashi

"A novel selenium removal process called Recycled Green rust/Ferrite Process is developed by MMC. In this process, a mixed Fe2+-Fe3+ hydroxide compound, green rust (GR), reduces selenate to elemental selenium, while GR is consequently oxidized to magnetite Fe3O4. Sequencing batch-mode experiment showed that the residual selenium concentration gradually decreased with the number of batch test increased. Stable selenium removal was achieved when the number of batch test exceed 15 times. Optimum selenium removal ratio reached 99.95% where initial Se concentration 2.1mg/L decreased to 0.001mg/L. Furthermore, the continuous feeding test carried out through a pilot-scale plant with a feeding capacity 600 L/hr. Approximately 860-hour-feeding test was carried out for the selenium-contaminated groundwater which had an averaged selenium concentration of 0.88 mg/L. Selenium concentration in the effluent from thickener maintained less than 0.01 mg/L (selenium removal rate of 99%) until a net operating time reached 800 hours.IntroductionJapan is one of the largest producers of selenium, and thus there are potential environmental impacts of selenium on soil and aquatic environments. The Mitsubishi Material Corporation (MMC) owns some real estate properties whose soil and groundwater was polluted by selenium and other heavy metals. These sites include former industrial plants: a smelter for nonferrous metal and a fabricating semiconductors and pigments. Selenium in aquatic environment commonly exists in four oxidation states, namely, VI, IV, 0 and -II. Selenate ion (SeO4 2-), the most oxidized form of selenium, and selenite ion (SeO3 2-) are highly soluble and mobile. Elemental selenium (Se0) is insoluble in water and therefore has much lower toxicity. Because selenium is carcinogenic and teratogenic at high concentration, the national effluent standard in Japan is fixed at 0.1 mg/L and the environmental standard at 0.01 mg/L. Although there are several selenium removal techniques, the most conventional process is coprecipitation with a ferric hydroxide because of its simplicity and low cost. It is known that selenite is adsorbed strongly on the surface of ferric hydroxide, but selenate is not. The low affinity of selenate on oxide mineral surfaces was demonstrated by the fact that selenate could be easily displaced by adding competing anions, particularly sulfate ion. Selenate removal from polluted water is one of the most difficult techniques, and more effective methods are desired. MMC developed a novel selenium removal process [1]. In this process, the concentrated slurry that contains Fe(II)-Fe(III) hydroxyl-salts known as Green Rusts (GRs) contributes to selenate removal. The main components of the iron precipitate in the reactor are GRs and their oxidation product, magnetite (Fe3O4)."

Jan 1, 2008

By Artur R. P. Junior Sergio, Pedro A. Netto, N. Monteiro, Foluke S. de Assis, Frederico M. Margem

Synthetic fibers are being replaced gradually by natural materials such as lignocellulosic fibers. Compared to synthetic fibers, natural fibers have shown advantages in technical aspects such as environmental and economic. So there is a growing international interest in the use of those fibers. The banana fiber presents significant properties to be studied, but until now few thermal properties on banana fiber as reinforcement of polyester matrix were performed. The present work had as its objective to investigate, by photoacoustic spectroscopy and photothermal techniques the thermal properties of diffusivity, specific heat capacity and conductivity for polyester composites reinforced with banana fibers. In the polyester matrix will be added up to 30% in volume of continuous and aligned banana fibers. These values show that the incorporation of banana fibers in the polyester matrix changes its thermal properties.

Jan 1, 2015

By Shaik Jeelani, Mahesh Hosur, Esperidiana A. B. Moura, Rejane D. Campos, Emilia S. M. Seo, Kerry Kirwan, Francisco R. V. Díaz, Maria Sotenko

The use of natural fibers with polymeric resins has spread rapidly. In order to improve the mechanical properties of material, in this work, two variables were used: mercerization and electron beam irradiation. This paper describes the preparation and characterization of biocomposites that were prepared in two different routes using green high density polyethylene (HDPE) and Brazil nut pod fiber (BNPF): the first was to irradiate the composite with 150 kGy and the second was to irradiate the matrix with 15 kGy followed by composite preparation. In both cases mercerized and non-mercerized fibers were used. The irradiation process was carried out using a 1.5 MeV electron beam accelerator, at room temperature and in the presence of air. The material was characterized to evaluate the effect of treatment on mechanical properties of material.

Jan 1, 2015

By Lucas Barbosa de Souza Martins, Felipe Perissé Duarte Lopes, Nathalia Carneiro Garcia Rosa, Lucas Lopes da Costa, Sergio Neves Monteiro, Rubén Jesus Sanchez Rodriguez

"The fibers extracted from the stem of the banana plant are relatively stronger and have been used as reinforcement of polymer matrix composites. In addition to quasi-static mechanical properties, there is a need to characterize the dynamic behavior of banana fiber composites subjected to thermal and mechanical constraints. In this work, the temperature variation of the dynamicmechanical parameters of polyester composites incorporated with up 30% in volume of banana fibers were investigated by DMA tests. The storage and loss moduli as well as the tangent delta were measured from 20 to 200°C in a TA Instrument operated with the flexural mode at 1 Hz. The results showed that the incorporation of banana fibers tends to increase the viscoelastic stiffness of the polyester matrix. It was also observed changes in the T g and the structure dumping capacity of the composites with increasing fraction of banana fibers.IntroductionNatural fibers with high amount of cellulose, also known as lignocellulosic fibers, have been used from primeval times by our civilization. In the last century, synthetic fibers such as nylon, carbon, aramid and glass fibers gained interest owing to superior strength and precise dimensional control. Natural fibers were then replaced by synthetics in many fields such as textiles and appliances. In the past decades, however, environmental issues drawn, once again, the attention to lignocellulosic fibers as possible substitute for intensive energy-consuming and long term polluting synthetics, specially the glass fiber [1]. In particular, research works have disclosed the potential advantages associated with the use of lignocellulosic fibers as the reinforcing phase in polymer composites [2-7]. Among the advantages it is worth mentioning the renewability, recyclability, biodegradability and the fact that natural fibers are neutral with respect to C02 emissions responsible for global warming. Moreover, as compared to synthetics, lignocellulosic fibers present lower density and cost as well as reduced wear caused to the processing equipment. On the other hand, in terms of composite reinforcement, hydrophilic lignocellulosic fibers present drawbacks such as weak adhesion to hydrophobic polymeric matrices in addition to dimensional limitations and non-uniform properties."

Jan 1, 2011

By Pedro A. Netto, Sergio N. Monteiro, Foluke S. de Assis, Rômulo L. Loiola, Frederico M. Margem

Banana fibers are among the lignocellulosic with great potential for use in polymer composites, such as the variety from the Musaceae family, due to its low density and good mechanical properties. In this work, epoxy matrix composites incorporated with continuous and aligned banana fibers were tested for their flexural behavior. Specimens with up to 30% in volume of fibers were bend-tested until rupture. The results showed an increase in both the composite mechanical strength and the stiffness with incorporation of these fibers. A fractographic analysis by SEM examinations a moderate adhesion mechanism between the banana fiber and the epoxy matrix. This mechanism is apparently responsible for the improved performance of the composites.

Jan 1, 2015

By Esperidiana A. B. Moura, Célio H. Wataya, Roberta A. Lima, Rene R. Oliveira

Biodegradable starch/copolyesters/silica nanocomposite films were prepared by melt extrusion, using a twin screw extruder machine and blown extrusion process. The influence of the silica nanoparticle addition on mechanical and thermal properties of nanocomposite films was investigated by tensile tests; X-rays diffraction (XRD), differential scanning calorimetry (DSC) and Scanning electron microscopy (SEM) analysis and the correlation between properties was discussed. The results showed that incorporation of 2 % (wt %) of SiO2 nanoparticle in the blend matrix of PBAT/Starch, resulted in a gain of mechanical properties of blend.

Jan 1, 2015

By Jean Igor Margem, Rômulo Loiola, Sergio N. Monteiro, Foluke S. de Assis, Frederico M. Margem

"Fibers extracted from the ramie plant have been traditionally used in textile and are now being considered as polymeric composite reinforcement owing to their superior strength. Recently the mechanical behavior of ramie fiber reinforced polyester composites was investigated but no significant improvement was found. Therefore, the objective of this work was to carry out a similar investigation by changing the type of polymeric matrix. Specimens with up to 30% in volume of ramie fibers incorporated into epoxy were bend-tested until fracture. The results showed a moderate improvement with a tendency of decreasing stress for higher amounts of ramie fibers due to the weak interface developed with the epoxy matrix.IntroductionThe engineering application of natural fibers extracted from cellulose-containing vegetables, also recognized as lignocellulosic fibers, is presently considered an environmentally correct alternative to replace more expensive, non recyclable and energy-intensive synthetic fibers [1-3]. In fact, composites reinforced with traditional fibers such as coconut, sisal, jute, hemp, etc ... are already on the market in substitution for common glass fiber automobile components [4-6]. Even less known fibers like curaua from the Amazon region are being industrially used [7]. Economical and environmental reasons sustain a promising future trend for natural fiber composites. In comparison with the less expensive glass fiber among energy-intensive synthetics, lignocellulosic fibers are approximately five times cheaper. For the current situation of our planet, natural fibers are regarded as ""green"" environmentally friendly materials. They are abundant, renewable, biodegradable, and recyclable, above all, neutral with respect to carbon dioxide emission, associated with global warming.Several relatively unknown lignocellulosic fibers such as piassava [8], sponge gourd [9], sugar cane bagasse [10], buriti [11] and ramie [12], with simple and limited applications, or just byproducts, are now being investigated for their potential as composite reinforcement. This could widen the offer of new lignocellulosic fibers for composite reinforcement. The banana fiber, in particular, has a tensile strength around 700 MPa [13], which is comparable to the strongest lignocellulosic fibers used as composite reinforcement.In addition to polyester, the epoxy is another relatively strong polymer used as composite matrix. Therefore, the objective of the present work was to assess the mechanical properties obtained by flexural test, for epoxy composites reinforced with different amounts of banana fibers."

Jan 1, 2013

By Ross W. Smith

Microorganisms are increasingly finding use in mineral processing and hydrometallurgy both for the enhancement of mineral engineering operations and for the remediation of mineral industry wastes. Some of the applications, such as biologically assisted leaching of sulfide ores and biooxidation of refractory sulfide gold ores, are established commercial processes. Others, such as the use of organisms for the removal of heavy metal ions from dilute aqueous streams, are nearing commercial application. Other uses of microorganisms are potentially possible. These include use of microorganisms in leaching non-sulfide ores, the flocculation or flotation of minerals and remediation of toxic chemicals discharged from mineral engineering operations.

Jan 1, 1993

By C. P. Manning

This paper reports recent progress in the development of a unique metal extraction technology utilizing zirconia-based inert anodes for the electrolytic reduction of metals from their oxides. In this process, the target metal oxide is dissolved in an ionically conducting liquid solvent phase. An extended anode consisting of an oxygen-ion-conducting stabilized zirconia membrane in intimate contact with a catalytically active electronic phase and an inert electronically conducting cathode are inserted into the molten flux containing the oxide. When the appropriate electric potential is applied between the electrodes the target metal is reduced at the cathode and oxygen ions are selectively transported across the stabilized zirconia membrane and oxidized at the anode. When the process is conducted at temperatures between 1200-1400°C, the ohmic resistance drop across the stabilized zirconia membrane is low, and high current densities on the order of I A/cm2 or greater can be obtained. In addition, the process efficiency can be increased further by directly reforming hydrocarbon fuel over the anode. Laboratory experiments at Boston University have demonstrated the technical viability of employing zirconia-based inert anodes for environmentally sound production of metals such as magnesium, tantalum, aluminum, etc., directly from their oxides. Significant progress has been made in the application of this concept to the electrolytic reduction of magnesium at 1300°C. The research topics covered include stability of the zirconia membrane in the selected molten solvent (flux), volatility of the flux, electrochemical characterization of the electrolytic cell, and analysis of the metals produced.

Jan 1, 2003

By Katsuyoshi Kondoh

The synthesis processing of Mg2Si or Mg2SiIMgO at lower temperature from the elemental magnesium alloy powder/chips and Si or SiO2 powder mixture was established via the repeated plastic working (RPW) based on Powder Metallurgy (PIM) process. RPW is much effective on the mechanical breakage of MgO surface films, which prevent from the solid-state reaction between Mg and Si powder. The solid-state synthesized Mg2Si particle of 200nm-2um is extremely fine, compared to that via the conventional casting process, causing the coarse one of 50-100um. This is because of not coarsening during the solid-state synthesis of Mg2Si. By using in-situ fonning process of Mg2Si via RPW and pre-heating before hot working such as extrusion and forging, the magnesium composite material with Mg2Si or Mg2Si/MgO dispersions was developed in employing Si or SiO2 particles, respectively. For example, when employing AZ31 chips as raw materials of the matrix, it has low density of 1.85g/cm3 and extremely superior mechanical properties, such as tensile strength over 350MPa with 5-10% elongation and Young's modulus of 47-50GPa, to the conventional Mg-Al-Zn alloys. The Mg composite alloy wires and pipes were produced via the hot extrusion process in the manufacturing plant, and also showed excellent mechanical properties.

Jan 1, 2003

By Katsuyoshi Kondoh

The synthesis processing of Mg2Si or Mg2Si/MgO at lower temperature from the elemental magnesium alloy powder/chips and Si or SiO2 powder mixture was established via the repeated plastic working (RPW) based on Powder Metallurgy (P/M) process. RPW is much effective on the mechanical breakage of MgO surface films, which prevent from the solid-state reaction between Mg and Si powder. The solid-state synthesized Mg2Si particle of 200nm-2JIm is extremely fine, compared to that via the conventional casting process, causing the coarse one of 50-100um. This is because of not coarsening during the solid-state synthesis of Mg2Si. By using in-situ forming process of Mg2Si via RPW and pre-heating before hot working such as extrusion and forging, the magnesium composite material with Mg2Si or Mg2Si/MgO dispersions was developed in employing Si or SiO2 particles, respectively. For example, when employing AZ31 chips as raw materials of the matrix, it has low density of 1.85g/cm) and extremely superior mechanical properties, such as tensile strength over 350MPa with 5-10% elongation and Young's modulus of 47-50GPa, to the conventional Mg-Al-Zn alloys. The Mg composite alloy wires and pipes were produced via the hot extrusion process in the manufacturing plant, and also showed excellent mechanical properties.

Jan 1, 2003

By Junji Shibata

As one of the effective usages of various wastes discharged in non-ferrous metal industry, the synthesis of hydrotalcite was carried out using aluminum dross as a raw material. Hydrotalcite is one of the inorganic anion exchangers and has layered structure of complex hydroxide. The removal of toxic metal ions such as As(III), As(V), Cr(VI) and Se(IV) with the hydrotalcite was investigated, and the removal properties were compared from the viewpoint of the anion exchange amount and exchange rate. Hydrotalcite can be obtained by a co-precipitation method from the aluminum dross and the waste MgCl2 solution discharged in an aluminum regeneration process. Slight amounts of SiO2, Al2O3, Fe2O3 and so on remain in the reaction product as an impurity component. Interlayer distance of the obtained hydrotalcite is about 0.3nm. Hydrotalcite changes to Mg-Al oxide by the calcination at 773K for 3h, and then hydrotalcite is formed again by a rehydration operation after calcination. The toxic metal ions are removed from aqueous solution by the anion exchange reaction in the pH region where toxic metal ions exist as the anionic species like AsO2-, HAsO42-,CrO42-, and SeO32-. The exchange amount is considerably concerned with the valence of anionic species and the size of anionic species. The removal of toxic metal ions were investigated from the engineering aspects such as the low concentration limit to be removed, the amount of hydrotalcite to be used for the perfect removal of toxic metal ions and so on.

Jan 1, 2006

By Scott R. Giese, Lucas Dix

"Recently, there is a growing trend in the aluminum foundry industry to develop· improved melting and casting processes to produce lightweight, high-strength, and thin-wall castings for the aerospace and transportation industry. One casting method that has demonstrated industrial potential for producing clean, thinwall castings is vacuum-assisted, counter gravity casting. This process has the benefit of expeditiously and quiescently filling the casting cavity with a dramatic reduction of furnace related and reoxidation inclusions. Additionally, lower casting temperatures can be utilized because the application of vacuum during filling overcomes the resistive internal cavity pressure resulting in a finer, as-cast microstructure. The paper explores and discusses the processing and design conditions in improving the mechanical properties of A206 casting alloy using the vacuum assisted, counter gravity casting process.IntroductionThe process of metal casting has been, over the centuries, the chief production technique for components used in everyday life. However, the casting process has certain inherent problems that can adversely effect the properties of a finished product. These problems are directly attributable to the gravity pouring technique used to transfer molten metal to the mold and to fill the mold cavity.A recent study for the American Metalcasting Consortium demonstrated reoxidation products created during the casting process are five times more likely to cause product rejects than entrapped molding aggregates, melt slag, or furnace lining materials1. Formation of nonmetallic and intennetallic compounds are more prevalent in aluminum and titanium alloys because of their reactiveness to furnace lining materials and their high affinity for oxygen. The incorporation of undesirable compounds can be attributed to four areas of the casting operation. The sources are charge materials, melting technique, pouring methodology, and casting cavity filling. Aluminum foundry men have addressed the first three areas by selecting high quality melt stock, non-stirring melting equipment, and the use of porous ceramic filters. Unfortunately, little consideration is given to the last, but yet tl.1e most important part of the casting operation, the actual fill mg of the casting cavity.The generation of inclusion defects during the casting process can be described by two methods. As the liquid metal flows in the gating network and casting cavity, abrupt changes in flow d1rect10n cause the metal to become agitated. This mechanism liquid metal splashing, is generated by instability of the advancing liquid metal interface from turbulence effects as schematically illustrated in figure 1a2 . The surface oxide film bursts under high velocity conditions, folds over, and becomes dispersed and incorporated in the bulk liquid. Additionally, fragmented liquid droplets ejected from the disturbed interface oxidize and become dispersed in the metal stream."

Jan 1, 2000

By Fernanda de Paula, Lázaro A. Rohen, Sérgio N. Monteiro, Rafael G. de Castro, Carlos Maurício. F. V, Maycon A. Gomes, Frederico M. Margem, Anna C. C. Neves

Synthetic fiber has been gradually replaced by natural fiber, such as lignocellulosic fiber. In comparison with synthetic fiber, natural fiber has shown economic and environmental advantages. The natural fiber presents interfacial characteristics with polymeric matrices that favor a high impact energy absorption by the composite structure. However, until now little has been evaluated about the hemp fiber incorporated in polymeric matrices. This study has the purpose of evaluate the impact resistance of this kind of epoxy matrix composite reinforced with different percentages of hemp fibers. The impact resistance has substantially increased the relative amount of hemp fiber incorporated as reinforcement in the composite. This performance was associated with the difficulty of rupture imposed by the fibers resulting from the interaction of hemp fiber / epoxy matrix that helps absorb the impact energy.

Jan 1, 2015

By Sergio N. Monteiro

Lignocellulosic fibers obtained from plants like cotton, flax, hemp, sisal, jute and many others are natural materials used, since long time, in basic items such as textile, baskets, roofing and carpets. These traditional natural fibers as well as some new ones are nowadays replacing synthetic fibers as composite reinforcement owing to environmental advantages. The heterogeneous characteristic of lignocellulosic fibers is, however, a limitation for application in composites. The buriti fiber, extracted from a tropical plant tree, is recently being investigated as a possible reinforcement for polymeric matrix composites but no complete information exists regarding its mechanical behavior. The objective of this work was then to carry out a statistical analysis on the mechanical properties? uniformity of buriti fibers. By precise dimensional measurements in association with tensile tests, it was found that the mechanical properties depend on the range of the fibers? dimension.

Jan 1, 2009

By Lucas L. da Costa, Sergio N. Monteiro, Romulo L. Loiola, Tammy G. Rodrigues Portela

"The fibers extracted from the petiole of the buriti palm tree are relatively strong as compared to other lignocelluloses fibers, with a potential for composite reinforcement. In this work, polyester matrix composites incorporated with these fibers were investigated for their flexural behavior. Specimens with up to 40% in volume of continuous and aligned buriti petiole fibers were bendtested until rupture. The results showed an increase in both the composite mechanical strength and the stiffness with incorporation of these fibers. A fractograph analysis by SEM disclosed a moderate adhesion mechanism between the buriti petiole fiber and the polyester matrix. This mechanism is apparently responsible for the improved performance of the composites.IntroductionIn recent years, the substitution of energy-intensive synthetic materials for natural ones is being considered in many industrial sectors including automobile, packing and textile [1]. A typical case is that of natural fibers, mainly those obtained from cellulose-based plants also known as lignocelluloses fibers. They have being investigated in the past two decades, aiming to replace synthetic fibers, particularly the glass fiber, commonly used as polymer composite reinforcement [2-8]. From the engineering point of view, lignocellulosic fibers present today important environmental, economical, societal and technological advantages already discussed [7-8]. Moreover, several lignocellulosic fibers are known since the beginning of our civilization and still cultivated or naturally extracted all over temperate and tropical regions of the world. According to Kalia et al [1 ], these fibers can be classified by their origin, as shown in Table 1."

Jan 1, 2011

By P. J. Mackey

Over the course of Dr. Robertson’s career, the ferrous and non-ferrous plants have seen enormous changes in technology and increases in plant capacity, essentially amounting to a “technological revolution”. In iron and steel, the “mega” blast furnace of some 6,000 m3 working volume is now standard (~10,000 tonnes (mt) of pig iron/day). Similar huge changes in process technology and plant size have occurred in the non-ferrous industry. As an example, the fuelfired reverberatory furnace, once the mainstay of the copper industry, has disappeared - replaced by large capacity flash and bath smelting technologies. The energy consumption per unit mass of metal produced has also been reduced considerably. Our understanding of the thermodynamics and mechanisms of metallurgical reactions, a field to which Dr. Robertson has significantly contributed, has made great strides. This paper reviews these changes with particular reference to the copper smelting industry, providing also comments on expected future trends.

Jan 1, 2014

By H. Y. Sohn

The considerable progress made in the sulfide smelting technology since the first International Sulfide Symposium of 1983 is discussed. The new developments and innovations have largely been driven by the recognition of environmental concern as well as the need for increased productivity. The smelting technologies for various nonferrous metals are reviewed, with an emphasis on the industry trend towards larger plants and continuous processes. The tremendous advances made in process modeling and computer simulation to describe the complex smelting processes are also reviewed. The goal of these mathematical models is the quantitative description of the processes and the reactors that will provide a means for the control and optimization of smelting operations as well as the optimal design of the operating conditions and the reactors. Environmental issues remain a key consideration in the smelting industry. One of the most remarkable improvements made in the last fifteen years since the 1983 Sulfide Smelting Symposium is the rapid increase in the sulfur capture by nonferrous smelters. This and other related issues are briefly discussed. Finally, the challenges that the smelting industry faces as the new millenium approaches are discussed. The industry continues to face technical challenges to improve productivity and efficiency, while being responsive to ever-increasing public pressure for environmental protection. It also faces external challenges from factors that may cause the reduction of metal uses as a result of substitutions by other materials. Another serious challenge and dire consequence that the primary metals industry is expected to face is the serious diminution of university-educated manpower as well as basic-research output. To remain competitive and healthy, the industry should take up the void left by the complete disappearance, at least in the U.S., and the reduction in other nations, of the governmental support of higher education and basic research in the field of primary metals production.

Jan 1, 1998

By Konstantina Chalastara

Mixed phase titanium dioxide (TiO2) nanoparticles synthesized through hydrolysis of TiCl4 solution at different conditions, namely concentration, pH, and residence time are characterized and evaluated as photocatalysts. The process is operated in a continuous stirred-tank reactor, CSTR giving blends of anatase, brookite, and rutile nanoparticles that were further evaluated to find the optimum mixture for a photocatalytic sorption material. The titania nanoparticles are first characterized in terms of photocatalytic activity under UV light illumination using an organic model compound (methyl orange) and after that are tested for removal of toxic selenate and selenite species from simulated effluent waters.