Search Documents

By Michal Rehor, Vladimir Cablik, Peter Fecko, Tomas Lang

"1. Introduction The North-Bohemian Basin area is known for its largest Czech brown coal deposit. About 50% brown coal reserves have been exploited in the North-Bohemian Basin by the mining company of Severoceske doly, a.s. (North Bohemian Mines, j.s.c.) today. The opencast mining of brown coal naturally led to vast landscape damages. Therefore reclamation work has acquired great significance. The specific feature of Severoceske doly, a.s. mining is the fact that the mining has been realized in two geologically absolutely different localities. This fact demands even rather different methods of reclamations. The main problem at Doly Bilina localities is the occurrence of overburden rocks from the series of rocks of coal seams. These rocks are texturally light but large amounts of coal (cca 5 %) and sulphur (cca below 3 %) which makes the soil reaction extremely acid. If they appear on the surface of the dump, they create a phytotoxic area, reclamation of which requires special methods. Rocks from Doly Nastup Tusimice localities are more suitable to reclamation use, but texturally extremely heavy rocks with large fraction of physical clays appear there that can generate a sterile soil area. Their reclamation requirements are completely different from those on Doly Bilina phytotoxic areas. That is the reason of the application of some non – traditional restoration methods. This report briefly summarises the experience in application of fertilizable soils, power plant stabilizer, power plant ash and aerial sowing of charlock. The results are documented by the monitoring of the physical, mineralogical and pedological parameters of rocks in testing areas.2. Properties of Overburden Rocks in Opencast Mines Bilina and Libous The reclamation work methodology in the North Bohemian Basin is above all determined by the properties of overburden rocks which occur in the top horizon of the reclaimed sites. The research of the rocks reclamation properties dealt with four current mining localities in the central part of the basin. It concerned the Bilina and Libous mines. This chapter states the stratigraphic status properties of these sites with respect to reclamation availability. The total status of the area of interest is shown in the figure No. 1."

Jan 1, 2008

By H. L. Fraser

A review of the possibilities of performing microchemical analysis in thin sections using a combination of scanning transmission electron microscopy and energy dispersive spectroscopy of x-rays is given. Particular attention is paid to the factors that limit accurate analysis at the highest spatial resolution. As an example of the use of these techniques applied to a potential problem in minerals processing, the identification of iron pyrite and pyrrhotite particles in Illinois, Herrin #6 coal is presented.

Jan 1, 1981

By P. T. Velu

Solubility of metal oxides in the molten salt electrblytes is an important parameter in the electrochemical processing of metals and alloys. The efficiency of an electrochemical process primarily depends on the quantity of metal oxide present in the electrolyte in the dissolved form and its thermodynamic properties. The activity of CeO2 was calculated using the free energy of fusion of CeO2,{ AG°m, CeO2. The AGOm,CeO2 }was deduced from the values of enthalpy, heat of fusion and melting point of Ce02. The activity coefficients of CeO2 as a function of temperature and melt composition were calculated. The thermodynamic data such as integral molar enthalpy, entropy and Gibbs energy of formation were calculated as a function of composition and temperature.

Jan 1, 1994

By Moto Goto

Today, Pierce-Smith converters, coupled together with various types of smelting units, are used in most of the world's smelters, However, due to the "batch" processing nature, and problems associated with fugitive emissions during the transfer of melt and blowing stages, this arrangement will unlikely be adopted in future smelters. Modern day alternative processes include the Mitsubishi Process, Outokumpu Flash Smelting and Flash Converting Process, the Noranda Process, and the Ausmelt Process, but only the Mitsubishi Process is a "truly continuous" smelting and converting operation, producing a constant flow of blister without tapping, and is economically proven by long term commercial operations. This paper reviews recent advances in modern continuous converting technologies, with a special section devoted to operation of the "first standalone Mitsubishi C-furnace" coupled together with a Noranda Reactor, at Port Kembla Copper Pty, Ltd. in Australia.

Jan 1, 2003

By Moto Goto

Today, Pierce-Smith converters, coupled together with various types of smelting units, are used in most of the world's smelters. However, due to the "batch" processing nature, and problems associated with fugitive emissions during the transfer of melt and blowing stages, this arrangement will unlikely be adopted in future smelters. Modern day alternative processes include the Mitsubishi Process, Outokumpu Flash Smelting and Flash Converting Process, the Noranda Process, and the Ausmelt Process, but only the Mitsubishi Process is a "truly continuous" smelting and converting operation, producing a constant flow of blister without tapping, and is economically proven by long term commercial operations. This paper reviews recent advances in modern continuous converting technologies, with a special section devoted to operation of the "first standalone Mitsubishi C-furnace" coupled together with a Noranda Reactor, at Port Kembla Copper Pty. Ltd. in Australia.

Jan 1, 2003

By Michael F. Kitto

The production of sulphuric acid at base metals smelters is predominantly an involuntary activity and now comprises approximately 17% of all-forms sulphur supply in world terms. The majority of elemental sulphur is also produced involuntarily in response to environmental regulations regarding emissions from hydrocarbon processing plants. The paper examines the points of similarity and difference in the sulphur and smelter acid markets, and reviews their interactions. The reasons for the merchant acid market collapse of 1993 are analyzed, and the prospects of a recurrence are considered.

Jan 1, 1996

By W. C. Hellyer

The papers in this section provide several examples of the application of Process Mineralogy to metallurgical problems. Any experienced metallurgist could cite numerous other examples when process mineralogy has, or could have, provided data of value in his understanding of metallurgical processes. The data developed by mineralogic techniques may supplement conventional chemical analyses, but cannot be replaced by assays. Mineralogic and chemical analyses each provide different types of information. In order for the process mineralogist to interpret his results in the most useful manner, it is desirable that he should have some knowledge of metallurgical processes. Conversely, the metallurgist should have some knowledge of mineralogic techniques to understand the scope and limitations. Mineralogic examinations are time-consuming and expensive. To ensure the effort is not wasted, and indeed does not generate misleading information, the utmost care must be taken at every stage of sampling and sample preparation. The mineralogist may examine microscopically or by x-ray diffraction a one-gram sample representing a flow of possibly thousands of tons per day through a concentrator. Conditions in a concentrator change continually in response to changes in feed rate, feed characteristics, grind, reagent additions, temperature, circulating loads, etc. Lengthy sampling periods are required to ensure the samples examined are representative of average conditions. The sampling program should be drawn up jointly by the metallurgist and mineralogist. Sampling points should be selected with a view to ease of sample cutting. The sampler should be instructed in the method of cutting the samples, the weight or volume of sample to be taken at each cut, the sampling frequency, and sampling period. The sampling period required depends on the scope of the investigation. For example, if a complete survey is to be made of all final and intermediate products of a flotation concentrator, samples should be cut at not more than two-hour intervals, twenty-four hours per day, for not less than one week. For a more limited investigation of one circuit or one section of a concentrator, 'the sampling frequency could be increased to every hour and the sampling period reduced to one or two days.

Jan 1, 1981

By Tim Robinson, Michael S. Moats, Masatsugu Moritmitsu, Kathryn C. Sole, Lauri Palmu, Frank K. Crundwell

"Process technology and design trends for copper, zinc, and nickel electrowinning cellhouses include focusing on energy reduction, productivity, and acid mist abatement. Larger electrodes, longer cells, automation, and higher current densities are leading to more capital-effective designs. The latest cellhouse designs include installation of automated electrode-handling systems, thereby removing more operators from the cellhouse. These technology and design trends result in lower electrowinning operating costs and improved purity of electro won cathode.INTRODUCTIONTechnology transfer between similar industries is an important process in improving product quality and productivity, and reducing operating costs. The electrowinning (EW) recovery of base metals, such as zinc, copper and nickel, is no different. The zinc industry with its larger EW product-handling requirements as compared to nickel and copper, has been driven to automation technology and the use of larger equipment. This technology has been transferred to copper. Nickel has led development and application in large-scale anode and divided-cell technologies but, due to nickel being produced in multiple forms (not just cathode) and being a small part of the whole complex nickel process route, the quantities of electrowon nickel are small compared to copper and zinc. Copper process technology in acid mist abatement was recently transferred to nickel. The focus in copper EW has been on energy reduction and productivity."

Jan 1, 2012

By B. J. Jody

At Argonne National Laboratory, we have been developing a potentially economical process to recycle automobile shredder residue (ASR). We identified three potentially marketable materials that can be recovered from ASR and developed technologies to recover and upgrade these materials. We built and tested a field-demonstration plant for recycling polyurethane foam and produced about 2,000 lb (907 kg) of recycled foam. Several 300-lb (I36-kg) samples were sent for evaluation and were found to be of marketable quality. We are also preparing for a large-scale test in which about 200 tons (181 tonnes) of ASR-derived fines «0.25 in. [<0.62 cm]) will be used as a raw material in cement making. A major cement company has evaluated small samples of fines prepared in the laboratory and found that they meet its requirements as a substitute for iron ore or mill scale. We also produced about 50 lb (23 kg) of recycled acrylonitrile butadiene styrene (ABS) from obsolete automobiles and found that it has properties that could be readily upgraded to meet the specifications of the automotive industry. In this paper, we briefly discuss the process as a whole and summarize the results obtained from the field work on foam and fines recycling.

Jan 1, 1996

By Thomas Frost

In this time of market globalization, many industrial companies are including detailed arbitration clauses in their international contracts, in order to avoid the potential costs, delays, and uncertainties of litigation in foreign courts. Arbitration is less expensive and more flexible, procedurally, than court proceedings, and arbitral awards enjoy much greater international recognition than judgments of national courts. More than 134 countries have signed the 1958 United Nations Convention on the Recognition and Enforcement of Foreign Arbitral Awards, known as the "New York Convention", which facilitates the enforcement of arbitral awards internationally. There are several other similar arbitration conventions that provide for the enforcement of cross-border arbitral awards. Additionally, arbitral awards are not subject to appeal, whereas judgments of national courts are routinely subjected to a lengthy appeals process, and there are very few viable bases to challenge arbitral awards. This discussion will review key considerations in drafting arbitration clauses, including choice of law and choice of forum considerations; issues surrounding the selection of arbitrators; the discovery process; presentation of evidence; and enforcement of arbitral awards.

Jan 1, 2006

By Robert W. Hyers

Electromagnetic levitation has proven important in a wide range of experiments, all affected by fluid flow. For some experiments such as viscosity measurements, only whether the flow is laminar or turbulent must be established. For other experiments, however, quantitative assessments of velocity, shear stress, or shear strain rate are required. In most cases it is difficult or impossible to measure the internal flow in levitated droplets directly. The samples are usually small, opaque, reactive, high-temperature, metastable, or all of these. Furthermore, recirculating flow limits the utility of tracking surface particles, since they collect in stagnation points ratherthan following the flow. Most research groups have chosen mathematical modeling to assess the internal flow in levitated droplets. A variety of analytical and numerical methods have been applied, including both laminar flow and various turbulence models. A number of these models are reviewed and their impact on different containerless experiments is assessed. Much of the research reviewed here was performed by alumni of Professor Julian Szekely, and by others using similar methods.

Jan 1, 2006

By T. Kimura, H. Ohba

"Much effort has been made to reduce the energy requirement in zinc electrowinning. In order to keep energy consumption low, either to make cell voltage low or current .efficiency high is necessary. Decrease of cell voltage practically depends on how to reduce ohmic resistance in the electrolyte and the anode crust. To realize these, new concept was proposed and the pilot plant has been operated. The space between a cathode and an anode is halved by utilizing the frame insulator. With these frames the anodes and cathodes compose of a unit of electrodes, and this unit is handled by newly designed electrode handling machine (E.H.M.). The process includes lifting up electrodes, expanding the space between a cathode and an anode, cleaning them, stripping the deposited zinc and returning the unit to the cell. As a result, cell voltage is kept as low as calculated and predictable energy reduction has been achieved. IntroductionIn the recent trend of a rapid appreciation of the Japanese yen, Akita Zinc Refinery of Mitsubishi Metal Corporation has been confronted by problems of relatively high operating costs. In order to compete with other overseas zinc refineries, it is necessary to reduce the cost of zinc production, especially the cost of electric power which now accounts for .up to 35 % of the entire cost of production. Three fourth of the electric power used at Akita Zinc Refinery is for the electrolysis. Therefore it is extremely important to reduce the cost of electrolysis.There are two possible measures for solving the problem; one is to use more nighttime electricity taking the advantage of its inexpensive power price, and the other is to reduce electric power consumption.As a part of a rationalization plan carried out in 1986, Akita Zinc Refinery increased the number of operating cells. As a result, when nighttime electricity is used, the silicone rectifier has been able to operate at full capacity. Moreover, by new schemes of ""increase of area for electrodeposition by ralslng the liquid level of electrolyte"" and ""increase of the number of electrodes in each cell"", current density could be lowered and as a result, the electric power consumption has been improved. In order to raise nighttime ratio even higher, installation of an additional rectifier and cells would be required."

Jan 1, 1988

By Hanlu Xie, Liang Yu, Ping Wang, Yuanchi Dong

"The leaching process is the first step when recycling BF slag as raw material for some other products. While studying the kinetics of the BF slag leaching process, a fractal phenomenon was found, which indicated some interesting mechanism in the process. The result suggested a new understanding of the leaching process in detail which useful for the industrial applicationIntroductionTypical composition (wt. %) of blast furnace slag varied in a pretty wide range: SiO2 30–40, Al2O3 10–20, CaO 30–40, MgO 5–10.The ground granulated slag is commonly used as base of roadway (mixed with natural inert for paving, soil stabilization, etc.) or one of the resources of Portland cements because of its good hydraulic activity [1]. To recycle the slag economically, the selective recovery of some components of the slag may be considered. As main components exist in the slag, silica [2, 3 and 4] and alumina [4] recovery was first considered.While recovering of silica from the slag, silica gels are recovered selectively from the leaching solution deriving from the treatment of the slag with waste sulfuric acid. After separation of the exhausted solid of leaching, the silica gel is precipitated from the solution at pH 3.2. Although the silica gels obtained by this procedure contain many impurities and need some more work afterward, it is the first and important step for the process.In the prior work [5], silica extraction using blast furnace slag had been investigated, focused on the pH value of selectively silica extraction. In the present work, kinetics of the leaching process was focused. It is important to design an economical process.ExperimentalThe composition of the slag and the calcined gels has been determined by a LINK860 (Oxford Instruments, Oak Ridge, TN) energy dispersive spectrometer (EDS) in conjunction with a CAMBRIDGE S250-M2 (Cambridge Instrument Ltd., Cambridge, U.K.) scanning electron microscope(SEM). The leaching of slag and the precipitation of silica gels have been conducted at atmospheric pressure in a stirred reactor placed at temperature controlled by a heated water bath."

Jan 1, 2008

By R. D. Prengaman

Lead usage in paint, anti-knock gasoline additives, pipes, seals, and solder has declined markedly over the past 30 years. Products utilizing the unique properties of lead and its ability to be recycled have survived and grown. These products include shielding, glass (particularly TV and computer screens), sheet for roofing, stabilizers for PVC, insoluble anodes for metal production, electronic solders and lead acid batteries. With the loss of markets many companies have decreased lead product development efforts. Much of the patent lead materials development is devoted to lead acid batteries. In the past 25 years, the automobile battery has been almost doubled in power and reduced in weight, leading to a nearly three-fold increase in performance. Corrosion-resistant lead alloys and improved battery designs have made battery lead usage more efficient. The same corrosion-resistant battery alloys are utilized to increase the life of electrowinning anodes. The challenge for lead product development is not only to maintain and improve the existing lead products, but also to develop the growing lead acid battery market for telecommunications, uninterruptive power sources, remote area power, hybrid and electric vehicles. Lead

Jan 1, 2000

By M. Nilmani, H. Pham

"A mathematical model was developed for the dissolution of particles in gas-stirred liquid baths, linking the hydrodynamic flow field of the bath, the average particle trajectory and liquid-side mass transfer controlled dissolution kinetics. The model was validated by comparison with experimental data for the dissolution rates of urea particles in gas-stirred aqueous CaCl2 solutions measured during this study. The dissolution rates of urea. particles were measured using an image analysis system.The effects of operating conditions on the dissolution rates of urea particles were investigated. It was found that the key operating parameters influencing the utilisation efficiency of particles were the gas flowrate, particle diameter and lance submergence. An optimisation of the operating conditions for the model urea-aqueous CaCl2 system indicated that the utilisation efficiency increased with decreasing gas flowrate and decreasing particle size for a given lance submergence.IntroductionThe utilisation solid reagents in molten baths varies from one process to another, depending upon the rates and mechanisms of the reactions between the particles and melts, as well as the trajectory and residence time of the particles in the melts. Previous studies have not attempted to predict the utilisation efficiency of injected solids by coupling the motion of the particle with its dissolution rate. Instead, the particles have usually been assumed to remain suspended in the bath until completely dissolved, and the mass transfer coefficients were based on the average specific mechanical energy dissipation rates in the bath. Investigations of this nature relevant to the present study have been undertaken by Apelian et al. [1], Brucato et al. [2] and Langberg and Nilmani[3]. The objective of the present study was to develop a mathematical model, incorporating both the reaction kinetics between the particles and liquid and the particle motion simultaneously, to predict the dissolution rates and times of the particles. The mathematical model was validated by comparison with experimental dissolution rates of a cold model analogue system measured using an image analysis technique, and then applied to optimise the operating conditions in the model system."

Jan 1, 1996

By Hongmin Zhu, Guihua Wang, Xiangsheng Wang

"The anode process of carbon electrode in fluoride melt was studied by voltammetry and chronoamperometry. Anode gases were analyzed by gas chromatography on-line during controlled-potential electrolysis. Two peaks were observed on the cyclic voltammograms. According to the results of gas chromatography, the first peak was corresponded to the discharge of residual oxide ions, with the formation of CO and CO2. Discharge of fluoride ions occurred at 4.1 V vs. Li+/Li, and leading to the anode effect. With the occurrence of anode effect, small amount of CF4 was detected. As the potential reached 4.5 V, CF4 and C2F6 gas evolution occurred, and the current increased to form the second peak.1.IntroductionIn the primary production of Aluminum and some rare earth metals like neodymium, a departure from normal cell operation known as anode effect results in the generation of perfluorocarbons (PFCs), which have high global warming potentials [1]. Owing to the pressure of environmental protection, considerable research has been carried out to clarify the mechanism of anode effect and PFC generation of industry and laboratory cells in the aluminum electrolysis system [2-9]. The common result on PFC generation is that the PFCs are emitted from Hall-Heroult cells only when they are on anode effect. In this article, we selected LiF, the main electrolyte for the neodymium electrolysis [10-11], to perform further investigation on the underlying kinetics of PFC generation and the nature of the reactions at the electrode.2. ExperimentalAll experiments were carried out in an alumina tube reactor, which was filled with high purity helium atmosphere. Spectrographic graphite crucibles were used, which played the dual role of molten fluoride container and the counter electrode. Lithium fluoride was analytical grade. The experiments were carried out at 900 °C."

Jan 1, 2011

By J. W. Matousek

In the flash smelting of copper sulfide concentrates, the course of reactions from the burner tip, through flame "burn-out" (the point of oxygen depletion), to settled matte and slag is of particular interest in understanding the mechanisms of the process. Numerous reaction sets can be proposed to describe the chemical changes that might be taking place, but from outside the furnace no one set offers an obvious advantage in explaining the actual processes involved. Only a combination of mathematical modeling and flame and bath sampling can achieve this result. This paper shows that flash smelting, while still reasonably orderly, is a more complex process than suggested by the technical literature.

Jan 1, 1993

By Dirk Bergmann

During the spray forming process, a continuous molten metal stream is atomized by impinging high speed inert gas jets. In the generated spray cone, the resulting metal droplets are rapidly cooled by the huge temperature difference to the surrounding gas phase and thereby partly solidified during flight. After a certain flight and residence time inside the spray cone, the droplets impinge onto the solid substrate and form the product (deposit) by compaction. Material properties of this preform strongly depend on several process parameters and especially on the thermal and kinetic state of the deposited droplets at the point of impingement. Smaller droplets may cool very fast due to their low mass and impinge onto the product in a completely solidified state as solid metal powder particles. Larger droplets with big mass contain a higher amount of thermal energy and impact during the state of phase change or still as completely liquid. It is obvious, that a certain amount of liquid content in the droplets is needed for forming a homogeneous deposit. Therefore, the thermal history of metal droplets during flight in the spray cone is of great importance for overall process modelling and control. Modelling the effects of the impinging droplet mass on the formation and heat balance of the deposit, the thermal conditions of the droplet stream need to be temporary and spatially averaged at different locations. Averaging may be achieved in different ways, giving alternative results. A first method is averaging over the droplets total enthalpy which consists of the thermal content and the remaining latent heat of fusion within the droplets. A second method may yield the average over the heat content and the solid fraction separately. Results of these two methods depend on the application and the kind of information which one wants to achieve and show some deviations, which will be discussed in terms of consolidation and energy conservation of the deposit.

Jan 1, 1999

By H. Cepin

Production of non-ferrous metals is still principally performed in shaft and flame fired furnaces. Electric furnaces increase metal recovery, reduce environmental burdens and decrease energy consumption compared to conventional processes. Because non-ferrous metals have low melting and boiling points and aggressive slags design of the furnace, energy input, and slag conductivity and composition are very important. Secondary materials are easily handled in electric furnaces. Since additional amounts of lead, zinc and tin will become available from secondary sources in the future, electric furnaces are expected to replace conventional smelting furnaces. The paper describes technical, electrical, and process designs of electric furnaces peculiar to the reduction of non-ferrous metals. Electric and various thermic furnace processes are compared.

Jan 1, 1990

By J. K. Brimacombe

"Nearly all the easy things have been investigated in injection metallurgy. Water models have been used exhaustively to study mixing, gas distribution and flow in submerged jets. Mathematical models have been developed with their restrictive boundary conditions to quantify submerged gas jet behavior. While being valuable tools to our understanding of injection metallurgy, there is an obliqueness to their application. What we need now are measurements and modelling on the actual systems, hot and unfriendly, where gas meets liquid at temperatures above l000°C. This is where the challenge lies.AN APPRECIATONThere are those who follow the trail and there are those few who blaze new trails in search of novel concepts and processes. With his restless, inventive mind, Howard Womer is a trail blazer without doubt. Decades ago, he was a pioneer in the pursuit of continuous steelmaking with the WORCRA Process and, today, he is developing new processes for the treatment of waste. He is not only an inventor but has been a professor at the University of Melbourne and was the first Director of Research at BHP. He has influenced the lives of many people, including myself; with his achievements and humanity. Therefore it is most fitting that this symposium should be held in honour of Howard Womer, a luminary in the metallurgical world for over half a century.BACKGROUNDGas injection has been an integral part of pyrometallurgical processes since the early days of Bessemer, then of Pierce and Smith. Today, of course, one cannot imagine pyrometallurgical processes without submerged gas injection to effect reactions for metal extraction and refining, to provide mixing and to inject solids into molten metal, slag or matte. Spurred on by new developments like tonnage oxygen and argon production, the Savard-Lee concentric tuyere and porous plugs, new steelmaking processes have emerged; and now solids injection is changing copper extraction processes. The ingenuity of the extractive metallurgists who drove these developments is inspiring for they have applied gas injection to transform pyrometallurgical processes. Humankind has been the beneficiary.' Today these processes are safer, more efficient, cost effective, less energy intensive and more environmentally friendly."

Jan 1, 1996