Search Documents

By C. M. F. Vieira

Crushed fired brick waste, known as grog, screened at two different particle size, 840 (20 mesh) and 180 µm (80 mesh), was used in mixtures with clayey body to make typical red ceramics for bricks. The effect of the grog addition up to 20 wt.% on the properties of bricks fired at 700oC was evaluated. The results indicated that both the particle size and the amount of grog addition changed the fired properties of the clayey body. Additions above 5 wt.% of grog, with a coarser particle size, decreased the mechanical strength of both the dry body and the fired ceramic pieces. By contrast, grog with a finer particle size may be used up to 10% wt. without deteriorate the properties and corresponding microstructure of the clayey body.

Jan 1, 2009

By Mike Dry

Conventionally, lithium-bearing brines are processed via solar evaporation, chemical purification, and either electrolysis to lithium hydroxide or precipitation of lithium carbonate. Lithium-ion battery technology and electric vehicles are forecast to greatly increase the demand for lithium, but not all lithium-bearing brines are amenable to the conventional extraction process and new approaches are being developed. The chemistry associated with conventional lithium extraction is outlined and two new approaches are discussed.

By C. W. Whitten

Solis from an abandoned Pb battery processing facility were characterized prior to the selection of the extraction technique. Reflected light microscopy and electron beam methods were used to locate Pb-bearing phases and to quantify the compositions of the phases. It was found that the soils are composed primarily of quartz and feldspars with minor amounts of iron and titanium oxides. Lead is primarily present as an oxide or sulfate that is associated with the silicate minerals. Specific phases identified were PbO; Pb02; cerrusite, PbCO3; angleslte, PbSO4; galena, PbS; and magnetoplumbite, 2PbO3Fe2O3; or plumboferrite PbO2Fe2O3?

Jan 1, 1989

By Sergey Shabala

Green leaf tissues convert solar energy into the energy of chemical bonds of sugar molecules during the process of photosynthesis. The efficiency of this conversion can be much higher than efficiency of any of the currently known silicon-based solar panels. Importantly, vast amounts of CO2 are assimilated during this process. The efficiency of photosynthesis is critically dependent on the availability of a large number of nutrients, among which metal cations such as K, Ca, Mg, Cu, Zn, Fe, Mn, and Ni play a key role. In this paper I summarize basic requirements and major functions for each of these essential nutrients in plant photosynthesis, both at the whole-plant and molecular level. I will talk about how these requirements may be affected by the global climate trends and discuss the prospects of creating artificial photosynthetic “bioreactors” for efficient energy conversion and CO2 assimilation.

Jan 1, 2009

By Rak-Jun Choi

Plasma-induced damage of InGaN/GaN multiple quantum well (MQW) light-emitting diodes (LEDs) has been studied in terms of forward turn-on and reverse breakdown voltages, together with etch rate and surface morphology. The physical degradation of sidewall along with rough surface morphology of n-GaN caused by increased ion scattering induced the deterioration of the forward and reverse voltages. It was found that the turn-on voltage is sensitive to the surface roughness of the etched n-GaN and the breakdown voltage is strongly affected by the sidewall contamination. Annealing under nitrogen after the mesa etching improved the electrical properties of the InGaN/GaN MQW LEOs. Efficient blue light-emitting diodes (LEOs) were fabricated using InGaN/GaN triangular MQWs. The LEOs with triangular QWs showed a lower operation voltage and 2.4 times higher light output power than those with the rectangular MQW LEOs at 20 rnA and 20 "C. The intensity of electroluminescence (EL) at 20 mA was almost independent of ambient temperature in the triangular QW LEO, but decreased substantially in the rectangular one.

Jan 1, 2003

By Zhenyang Wang, Xingle Liu, Xiangdong Xing, Shan Ren, Hongen Xie, Jianliang Zhang

"Non-isothermal combustion experiments of different additive amount of bituminous (0, 20, 40, 60, 80, 100 wt%) were conducted by synthesized thermogravimetry analyzer(STA409PC) from room temperature to 900°C in air. The changes of combustion characteristic parameters o f pulverized coals in different atmospheres are analyzed. The results show that DTG curves of coal combustion move to low temperature zones when the amount of bituminous increases. It indicates that both ignition and burnout temperature are lower, burnout time decreases, combustion characteristic index obviously increases, and combustion performance of blending coal are improved. The iso-conversional method involving Kissinger-Akah-Sunose (KAS) method was used for the kinetic analysis of the main combustion process. The results indicated that, when the additive amount of bituminous varied from 0 to 100 wt%, the value of activation energy which would sharply reduce if the additive amount of bituminous was under 60% increased from 133.94 kJ•mol-1 to 78.03 kJ•mol-1by using KAS method.IntroductionPulverized coal injection (PCI) to blast furnace (BF) is an important way for saving energy and reducing resource consumption during the ironmaking process. In order to acquire higher coal injection quantity, the relevant research topics in the field of pulverized coal combustion technology such as enhancing the efficiency of pulverized coal combustion, improving the combustion characteristics and reducing the harmful gas emissions and so on received extensive attention in recent years [1,2]. The combustion of blending coal when the appropriate proportion is selected for coal and also mixed well- distributed could give full play to the advantages of various types to make up the defects of single coal which is widely used throughout the world. So the blending coal injection to BF could produce a good impact on safety and economy for productive process. Therefore, a large amount of experimental researches on the combustion characteristic of blending coal for anthracite and bituminous were carried out by experts and scholars around the world [2-7].Nevertheless, the systematic research on the combustion behavior of anthracite with different content of bitumite in a thermogravimetric analyzer (TGA) is less. So in this paper, using the method of multiple scanning rate of conversion method, bituminous to promote the pulverized coal combustion reaction was studied to analyze its promotion mechanism of pulverized coal combustion reaction process, and the kinetic parameters of activation energy was also calculated, which to provide theoretical basis for the rationalization of resource utilization."

Jan 1, 2014

By P. M. Swash

The paper describes the use of mineralogical methods in the exploration and evaluation of primary diamond occurrences. The most common methods that are used include the systematic search for kimberlitic indicator minerals, surface textural study of the indicator minerals, (garnet, spinel, ilmenite and chrome diopside) and alluvial macrodiamond studies so as to understand their provenance and guide exploration towards diamondiferous targets. The mineral chemistry of the indicator is used to positively assess the origin of the mineral grains and is also pivotal in the determination of the diamond potential of a deposit. Petrography of the primary deposit is able to identify the body to be kimberlitic and is also a support to the mineral chemistry findings. Unambiguous proof of a prospects potential to contain macrodiamond is proven by the occurrence of microdiamonds in the residues from the rock. The presence of a sufficient number of microdiamonds in the rock is enough to determine a semiquantitative grade estimate and warrant further metallurgical evaluation so as to determine its actual macrodiamond content.

Jan 1, 1991

By S. J. Gerdemann

The U.S. Bureau of Mines is studying the kinetics of wet oxidation of sphalerite concen- trate (ZnS) as a possible process for a gravity-pressurized reactor (GPR). At tempera- tures in excess of 200' C, a sphalerite water slurry will react with 0, to form zinc sul- fate (ZnSO,). However, the pressure required to keep the water from boiling at these temperatures has kept this reaction from becoming a viable continuous process. The GPR can easily obtain the high pressures required for this reaction. The reaction rate is complicated by the solubility of 0, in water and the further oxidation of ZnSO, to insoluble zinc oxysulfate (Zn4(OH),S04.4H20). The effects of pressure, temperature, and particle size on the rate of reaction were investigated. Reaction rate was found to be limited by the amount of oxygen in solution. However, at 250" C and 1500 psia, over 90 pct of the zinc was solubilized in less than an hour. The conditions for maxi- mizing the Zn++ in solution, while minimizing oxysulfate formation, are discussed.

Jan 1, 1993

By Nobuo Takahashi

Effective solvent extraction media have been investigated for purification of rare earths. At first, a quaternary ammonium compound was studied. The counter anions of rare earths and organic dielectric substances were tested to improve separation factors,. And second, crown ethers were selected for extractant. Several diluents of crown-adducts were tested to improve solubility and distribution coefficient as well as the counter anions of rare earths. Especially, in the presence of strong reducing agents, highly selective extraction of europium from other rare earths was observed. The third extactnts were ß -diketones. Presence of organic dielectric substances was very effective to improve separation factors. Though those. three groups of extractants were suitable for mutual separation of light rare earths, alkyl esters of alkyl-phosphonic acids were suitable for mutual separation of heavy rare earths because of their high separation factors. To keep proper pH value was necessary for acidic extractants, so control method of the solution pH was studied with high molecule insoluble amines or salts of those.

Jan 1, 1995

By E. B. Zanelato

The process of casting metals and alloys occurs through the fusion of this metal and its subsequent casting into a mold with the dimensions and geometry close to the final piece. Most foundries use sand casting molds for making you. This work aims to characterize and evaluate the foundry sand to allow its use in segments of Civil Engineering, creating a viable destination for a residue is that discarded. The following characterization tests were performer: particle size, chemical analysis, X-ray Diffraction and Density Real grain. For the execution of the test specimens was used to 1:3 cement and sand, and the incorporation of 10% and 20% of the total mass replacing the sand, and the trace reference. The results show that best results in compression and bending tests were obtained by replacing 10 % of common sand for sand casting.

Jan 1, 2015

By J. N. Hryn

This paper describes some of the work done in Phase 1 of a multi-year, five-phase program aimed at demonstrating the economic feasibility of producing commercial-scale quantities of commodity materials derived from salt cake residue-oxide. The amount of salt cake generated annually in the U. S. is estimated to be 510,000 tons, including 340,000 tons of residue-oxide. Used beverage can (UBC) processing accounts for the majority of residue-oxiae that could be made available for further processing into commercial products. To characterize the composition of residue-oxide. eight residue-oxide samples from various secondary processors were obtained and analyzed. Surprisingly, the composition of residue-oxide was found to be independent of source or alloy family being processed, with? the exception of slightly elevated silicon levels in 3XXand UBC residue-oxide samples. Major phases detected in the residue- oxide were? alumina, spinel, and aluminum hydroxides. Preliminary economic analyses indicated that the refractory market appears to be the best choice for high value-added products produced from residue-oxide with minimum processing. Bench-scale tests indicated that low silicon containing residue-oxide is ready to enter this market, but the elevated silicon content of UBC and 3XX residue-oxide preclude this possibility. A separation technology should 'be developed to remove silicon-containing . species from the alumina and spinel values Present in residue-oxide. This technology would then allow UBC and 3XX residue-oxides to be converted to significantly higher value-added products.

Jan 1, 1995

By Donna M. Noel

Bacterial strains have been cultivated from solids previously exposed to cyanide that will tolerate 300 ppm sodium cyanide under anaerobic conditions. In selected solid samples, these bacteria have been shown to reduce the level of cyanide from approximately 300 ppm to essentially zero in about 50 days under anaerobic conditions. Various media were investigated, and the nutrients providing maximal growth were ?established .. Degradation of cyanide in sterilized solids was determined for comparison with degradation obtained in bioactive solids. All experiments were conducted at ambient temperature and initial pH of approximately 10.5.

Jan 1, 1991

By F. A. Steward

Copper is one of the trace minerals essential to life. It is added, usually in the form of copper sulfate, to virtually all formulated feedstuffs and to dietary supplements fed to animals on forage. Over the past five years, an improved inorganic copper source trademarked Micronutrients TBCC™, has been developed, tested and commercially introduced. TBCC is a crystalline form of basic copper chloride. Synthesis is accomplished in a continuous neutralization I crystallization process. In current commercial production, the primary sources of copper currently used as feedstocks are the etching solutions used to manufacture electronic printed wiring boards. These solutions have traditionally been managed as hazardous wastes, but their use to manufacture TBCC™ exempts them from regulation as wastes under the "Use/Reuse" provisions of RCRA. Research conducted over five years at multiple universities has shown that animals are healthier when fed this source of copper and that vitamin losses in feed are reduced by its use.

Jan 1, 2000

By U B. Pal

Downsizing and decommissioning of nuclear facility operations is increasing the stockpile of various different grades of Radioactive Scrap Iron (RSI). Disposal of this material not only represents significant resource and value lost, but also necessitates long term monitoring for environmental compliance. The latter results in additional recurring expense. It is desirable to be able to decontaminate the RSI to a very low level that can be recycled or used for fabrication of containers for RSI disposal instead of using virgin metal to fabricate the container. Electro-Slag Remelting and Refining (ESR) is often used for decontaminating radioactive contaminated sources of scrap iron such as stainless steel. Non-radioactive oxides of cerium are used to simulate the radioactive oxide contaminants of Uranium and Plutonium. The success of the ESR process is strongly dependent on the capacity of the slag to rapidly incorporate the radioactive contaminant (simulant). In this study we have measured the slag-metal partition coefficient for cerium and investigated the reaction mechanism for the dissolution CeO, in the slag.

Jan 1, 2002

By James W. Reeves

DuPont was the titanium metal pioneer who put the greatest effort into both R&D and commercial sponge and powder metallurgy production. This was concentrated in the period 1945 through 1963. The commercial results were development of the chloride process for TiCl4 using ilmenite, development and improvement of the Kroll process, development of a modified Hunter process to make titanium powder and commercial development of a direct powder process. The powder metallurgical process failed because of the inability to meet powder chloride specifications. All this work remained a trade secret until published in NMAB -392 by Mahla in 1983. There were other processes explored by DuPont, both improved sponge and powder processes. Much of this work has been continued by others but none, as of yet, resulting in new improved titanium metal capacity.

Jan 1, 2001

By Xue Wang, Callie Babbitt, Chelsea Bailey, Matt Ganter, Gabrielle Gaustad, Brian Landi

"Current trends, motivated by fossil fuel dependence and unprecedented greenhouse gas (GHG) emissions, show lithium-ion batteries (LIBs) emerging as a competitive energy storage technology due to higher power and energy densities compared to Pb-acid and Ni-metal hydride chemistries. These trends may be of concern, however, as environmental impacts are not well understood for either the LIB itself, or for the nanoparticles consumed or released during the battery's production, use, or end-of-life. This study combines economic modeling, dynamic material flow analysis, and fundamental material characterization methods in order to quantify some of the economic and environmental trade-offs for LIBs at their end-of-life. As expected, results show that as chemistries transition from Li-Co based cathodes to Li based Fe, Mn, and S cathodes, LIB recovery value correlates to the value of the raw materials used. These initial results aim to inform collection policies being proposed currently as well as enable future deployment of novel recycling techniques.IntroductionGlobal fossil fuel dependence and unprecedented GHG emissions have led to increasing attention on energy alternatives, for both electricity production and personal transportation. However, development of renewable energy systems is contingent on concurrent technological development of energy storage systems, primarily batteries used for power grid load-leveling, renewable energy storage, and hybrid and battery electric vehicles. In this sector, lithium-ion batteries (LIBs) are emerging as a competitive technology due to higher power and energy densities compared to lead-acid and nickelmetal hydride chemistries[!]. LIBs represent close to 20% of the total rechargeable battery market and 75% of the portable rechargeable battery market, which is the fastest growing segment of the rechargeable battery market, with a 20% global growth in 2008 [2].This surge in production ofLIBs indicates a looming waste problem; total waste from Li-ion batteries has likely grown substantially from the 500 metric tons estimated in 2003 [3]. Figure IA shows the substantial increase in world-wide lithium production that has occurred in the last several decades with batteries making up the largest share of applications (Figure lB). California and New York state legislators have attempted to proactively address this looming waste by issuing diposal bans on rechargeable batteries in their states[4, 5]. However, quantification of the costs involved in collection, transportation, and processing of these materials has not been examined in depth."

Jan 1, 2012

By Vinicius Alves Gomes, Jean Igor Margem, Thallis Cordeiro, Frederico Muylaert Margem, Roberto Faria Jr., Sergio Neves Monteiro, Marina Rangel Margem

Natural fibers are attracting the interest of engineering sectors owing to specific advantages such as lightweight and lower cost as well as for their inherent condition of being renewable, biodegradable, recyclable and neutral with respect to CO2 emission. In particular, the fiber extracted from the malva plant stem is nowadays recognized as one of the strongest lignocellulosic fibers. However, the thermal properties of the malva fibers have yet not been fully investigated. The present work had as its objective to investigate, by photoacoustic spectroscopy and photothermal techniques the thermal properties of diffusivity, specific heat capacity and conductivity of a pressed malva fibers sample. The results revealed that these fibers showed a superior thermal insulation capacity.

Jan 1, 2015

By Zhang Chuanfu, Tan Pengfu

"A thermodynamic model is developed to predict the distribution behaviors of Ni, Co, Sn, Pb, Zn, As, Sb, Bi, Au and Ag in copper pyrometallurgical process. In this model, as more as 21 elements (Cu, S, Fe, Ni, Co, Sn, As, Sb, Bi, Pb, Zn, Au, Ag, 0, N, C, H, Ca, Mg, Al, and Si) and 72 compounds (in fayalite-slag-making system) or 74 compounds (in ferrite-slag-making system) are considered. Accessory-element behavior is studied for two types of slag , fayalite and ferrite, and two levels of oxidation. The allowance is also made to account for physical entrainment in the melts.-Model simulations are carried out to study the effects of controllable process parameters such as feed composition, smelting temperature, degree of oxygen enrichment and volume of oxygen enriched air. The model can be used in copper flash process, Mitsubishi process and Noranda process. The predictions by the present computer model are compared with the known industrial data from Gui Xi Smelter in China, Home Smelter in Canada and Naoshima Smelter in Japan and excellent agreement between calculations and industrial data is obtained. In this paper, the effects of oxygen enrichment, matte grade, smelting temperature, and types of slag on accessory-element behavior among matte, slag and gaseous phase have been elucidated.I . IntroductionThe presence of trace quantities of minor elements such as As, Sb and Bi in copper significantly reduces its ductility, electrical conductivity, and lowers its thermal conductivity. Embrittlement of copper also occurs due to impurity-phase precipitates at the copper grain boundary interfaces. They deteriorate not only the electrical conductivity of copper but its workability in hot working."

Jan 1, 1998

By Eric Klaffenbach

Valorization of slag from metallurgical industrial processes becomes ever more important as this may help optimizing and reducing the use of natural resources such as rock and sand. In view of this objective, metallurgical processes have to be analyzed in order to modify the slag composition so that it will meet the expected requirements of potential users of these resources. This paper gives the results of a thermodynamic analysis of the flash smelting process to understand the impact of operational parameters on slag chemistry and elemental partitioning in the process. It is shown that an increase of the matte grade and temperature leads to higher deportment of Pb, Zn and As to the slag. With increasing matte grade the volatilization of these elements decreases. Furthermore, the results indicate an increasing solubility of Cu and S in slag at higher temperatures.

By Shilai Yuan, Huimin Lu, Liyuan Zhao, Zhijiang Gao

"A purification process was developed to removal impurity element boron from metallurgical grade silicon by electromagnetic induction slag melting. Vacuum melting furnace was used to purify boron in both Al2O3-MgO-CaO-SiO2 slag system and Al2O3-CaO-SiO2 slag system. The relationship between different slag chemistry and the removal of boron in silicon were studied using Back Propagation (BP) Neural Network model. The best slag chemistry for the removal of boron was predicted by Genetic Algorithm (GA) contributed by the use of Matlab. The results show that the mass fraction of Boron in silicon is reduced from 11.7496×10-6 to 2.3259×10-6 after slag melting in 28.96%Al2O3-3.43%MgO-36.24%CaO-31.37%SiO2 slag system. The relative error obtained with GA-BP Neural Network model was below 0.35%.IntroductionSolar energy, due to its low green house gas emissions, has been paid great attention. Accordingly, the demand for solar grade silicon (SoG-Si) has been growing rapidly. The quest for developing a low-cost method of producing SoG-Si has been moving forward in the last decade. Refining of metallurgical-grade silicon (MG-Si) attracts research interest due to its low material and energy costs, and more environmentally friendly technology in comparison to the traditional Simens process. As such, impurity elements in MG-Si must be removed to low levels for the photovoltaics (PV) cell to operate at optimum efficiency. Most impurities in metallurgical-grade silicon (MG-Si), especially metal elements, can be separated by directional solidification and the zone refining plasma-arc method [1, 2]. The main focus in refining MG-Si to SoG-Si is on the impurities which are the most difficult to remove. Boron has relatively high segregation coefficients (KB=0.8, concentration of Boron in solid silicon divided by its concentration in liquid silicon) [3] and higher vapor tension (the saturated vapor pressure of boron and silicon are 6.78×10-7 Pa and 0.4 Pa, respectively). The vacuum melting and directional solidification methods hence have no effects on boron removal.Slag refining involves melting MG-Si in the presence of a flux to produce a slag phase that can take up the impurity elements. The mechanism of slag refining is considered to include two main steps: the oxidation of boron and the absorption of boron oxide by slag materials. The oxidation of boron, described by the oxygen potential (PO2), resulting from the equilibrium Si and SiO2. The absorption of boron oxide, described as the slag basicity, is interpreted as expected to facilitate their extraction to alkali and alkali-earth oxides in the slag phase. Thus, effective removal may be obtained for a certain slag composition. Researchers [4-5] examined the effect of boron removal in CaO-SiO2 based ternary systems and showed that the addition of excess CaO can decrease the activity of SiO2. Researchers [6-8] studied the boron behaviors in CaO-SiO2-Al2O3, CaO-SiO2-Na2O, Al2O3-BaO-SiO2, CaO-SiO2-Li2O and Al2O3-CaO-MgO-SiO2 slag systems by adding boron in the silicon to a degree. Li2O, Na2O, MgO and BaO are thought to be associated with B2O3."

Jan 1, 2014