Search Documents

By Tao Xuea

Gold frequently occurs in nature in the form of a gold-silver alloy. Thus, investigation of the electrochemical behavior of gold-silver alloys in cyanide solution has practical significance. In this paper, the potentiodynamic method is used to determine the anodic polarization curves of gold-silver alloys (Au-10% Ag and Au-50% Ag) in cyanide solutions. To facilitate the interpretation of the results, complementary experiments conducted in NaOH solution in the absence of cyanide are also reported. The results for the Au-Ag alloys are compared with the polarization behavior of pure gold and pure silver. With the aid of potential-pH diagrams for the Au- and Ag-CN-H20 systems and electrochemical kinetics concepts, the dissolution mechanism of gold-silver alloys, the effect of the presence of silver on the cyanidation of gold, as well as the factors which control the anodic reaction rate are clarified.

Jan 1, 1998

By Zenjiro Asaki, Teruo Tanabe

"To clarify the formation of light rare earth (R =Ce, Pr, Nd or Sm) -Fe compounds in the reduction-diffusion (RD) process, two kinds of experiments were carried out: (a) RD experiment in which briquettes composed of R oxide powder, Fe (particles or wire) and CaH2 were reacted, and (b) immersion experiment, where an Fe plate was immersed into R-Fe melt having the composition of Fe-side liquidus line in Fe crucible. The compound formation was examined by using XRD, SEM and EPMA. The formation rates of RzFe17 measured by the RD experiment were compared with those obtained by the immersion experiment. The growth rates of compounds obtained in the RD experiment for Pr-Fe and Nd-Fe systems were much lower than those obtained in the immersion experiment. This result was explained by the difference of the reduction rates of R oxides by Ca. The parabolic rate constants for the formation of RzFe17 were separated in two groups of (a) Pr-Fe and Nd-Fe systems and (b) Ce-Fe and Sm-Fe systems. This was discussed in connection with the difference of their crystal structures and the driving force of diffusion. The parabolic rate constants for the formation of compounds in Ce-Fe and Sm-Fe systems decreased in the order of RFez, RFe3 and RzFe17.IntroductionTo understand reaction behaviors in the production of rare earth (R) -iron intermetallic compounds, which have excellent magnetic properties, is very important from engineering point of view. And the reduction-diffusion (RD) process<O has recently attracted attention as one of the promising processes to economically produce R-related materials. A few fundamental studies on the compounds formation in the RD process have previously been reported. Qi, Hino and Yazawa(2) observed the formation of R(Nd, Sm)-Fe and R-Co compounds in the process from various view points. Song and Ogawa(3) measured the growth rates of Nd-Fe and Sm-Fe compounds by using Nd or Sm vapor supplied from Nd-Ca or Sm-Ca melts. The authors have also carried out fundamental studies (4)-(8) to clarify the rate and mechanism in the production of R-Fe intermetallic compounds."

Jan 1, 1998

By R. Stefaniuk, T. Le, J-Y Huôt, H. Henein

"One of the most important process variables in gas atomization is the gas to metal (G/M) mass ratio as it has a direct effect on the mean particle size of the atomized powder. If this ratio can be controlled during the atomization process, the powder produced would be more uniform and the d50 more predictable. Thus, atomization using a tundish or gravity feed from a crucible would be more stable. In gas atomization, the gas flow rate can be easily monitored; while it is very difficult to determine the molten metal flow rate. This research paper presents a new method of recording the molten metal height with time using a conducting metal height detector. The metal height recorded in real time during atomization was used to characterize using a model the friction losses in the metal delivery system. It is found that the integrity of the metal delivery tube and the cleanliness of the melt play a key role in the maintaining a stable metal feed.IntroductionIn the gas atomization process, molten metal is normally fed to the system either continuously using a tundish or in most cases a certain amount of metal is melted in a crucible and flows into the atomizing chamber under gravity. In the first case, the metal flow rate is believed to be constant during the atomization process despite the presence of slag or dross on the molten metal surface. In the second case, the amount of molten metal is depleted with time and the rate at which the metal flow decreases with time varies from test to test in a seemingly unpredictable fashion.' Furthermore, most atomization systems are confined units and the metal level in the crucible cannot be detected by a visualization method. In industry as well as in laboratories, the metal flow rate is normally calculated on either the mass of input material or the mass of total production divided by the duration of the test. This figure is not accurate enough and obviously cannot be used as a control parameter for the gas to metal ratio as it is only determined after the completion of an atomization run. The need exists for a metal flow rate measurement and control methodology; thereby the d50 of the powder produced may be estimated and controlled in real time. Clearly, the smaller the variation of the G/M ratio during the atomization process the more uniform the powder produced and hence the size of the particles can be predicted."

Jan 1, 1994

By Yoshihiko Maeda

"Although Japanese mining industry once had been a polluter of toxic heavy metals and gasses, it has been struggling for improvement of environment at mining and smelting facilities under the strict Japanese regulations. Through these efforts, the industry has developed various environmental technologies to be applied in other industries and society.Recycling of metal scraps, for example, has been conducted at smelting facilities. Treatment of hazardous waste, cleanup of contaminated soil and management of landfill are other examples of application of mining and smelting technologies and facilities. In accordance with the worldwide environmental concerns, the industry has become one of the leading industries to promote ""Sustainable Development"", and it is expected further contribution in reducing various environmental burdens to earth by utilizing its mining and smelting technologies and facilities. Some of the examples of these applications are presented in this paper.IntroductionDowa Mining Co., Ltd., established in 1984, is known as one of the ~op Japanese producer of nonferrous metals. Base on its special expertise in the mining and smelting of complex ores, it has expanded its business areas to downstream activities ranging from highly purified metals and alloys, electronics materials, chemicals and related various businesses. Dowa Mining now is becoming more active in the field of waste treatment and recycling.Dowa Mining had operated some mines until 1980th, located at the western part and northern part of Honshuu Island in Japan; the former is pyrite mine while the later is ""Black Ore"" mine,· a complex sulfide ore composed of high grade of copper,· silver, lead and zinc. However, due to the strong yen began in1985; Dowa Mining closed its mining operation in 1994, and has sifted to mining operations in Mexico."

Jan 1, 2000

By Naiyi Li, Henry Hu, Alfred Yu

"In the past few years, various squeeze cast aluminum components have been developed and successfully implemented in various vehicles by the automotive industry because of their superior engineering performance. However, fundamental understanding of the formation of air gap during squeeze casting processes is still very limited despite of its significant influence on the extent of heat transfer between the casting and mould. In this paper, a mathematical model has been developed to simulate phenomena of air gap between the casting and mold' during squeeze casting of aluminum alloys. The model considers the effect of process parameters such as applied pressures and mold temperatures on the events of air gap formation. The predication indicates that the occurrence of highly enhanced heat transfer in squeeze casting of aluminum alloys primarily results from the presence of excess applied pressures.IntroductionA number of squeeze cast Al components has been developed and used in mass-produced vehicles in the past few years, such as steering knuckles, Road wheel, Engine Block etc. This is attributed to their superior engineering performance. In squeeze casting, the cooling rate can be increased by applying high pressure during solidification which results in the noted refinement in the micro structure scale leading to better casting properties. However, the excessive pressure increased interfacial heat transfer coefficient is affected during the solidification by air gap formation and die surface condition etc., which is believed to increase thermal resistance at the casting/die interface [l - 4]."

Jan 1, 2004

By Naiyang Ma

"High oil concentration is one of the major barriers for recycling of mill scale of steel hot rolling mills. It is of vital importance to find cost-effective technologies of reducing oil concentration in mill scale in order to recycle the mill scale without causing detrimental effects on production and environment. This paper discusses in-process separation of mill scale from oil at steel hot rolling mills. Formation of mill scale and status of oily wastewater at hot rolling mills are reviewed in the first place. A mathematical model is then formulated to relate oil concentration in mill scale to physical properties of mill scale, chemical and physical properties of wastewater and interacting parameters between mill scale particles and wastewater. From this model, three approaches of in-process separation of mill scale from oil are derived: (1) avoiding contacts between mill scale particles and oily wastewater, and (2) maintaining low oil concentration in wastewater, and (3) collecting mill scale in upper streams of wastewater flows. In-process separation of mill scale from oil might have advantages of lower capital cost, lower operating cost and less additional environmental concerns, compared to other strategies of separating mill scale from oil.IntroductionHot rolling is an inevitable step in producing finished steel products. Figure 1 schematically shows a steel hot rolling process. Semi-finished steel products, slabs here, are reheated first, and then the reheated slabs are discharged from the furnaces and transported on hot rolling trains to descaling units for removing scale with pressurized water. After being descaled, the slabs are rolled by roughing mills. After treated with cropping and the second descaling, the slabs are finally rolled into finished products, coils here, by finishing mills."

Jan 1, 2012

By U. Lauwers

The influence of different waste materials in sinter blends on the quality and mineralogical composition of a sinter is described. As a result of partial preservation of the original textures of waste materials in the final product the degree of assimilation of the original material in the sinter product can be ascertained. Recycling of waste materials such as dolo char , arc-furnace slag, scrap fmes, mill scale and BOF-mud via the sintering process a saving on costs of raw materials such as flux and fuels, and a reduction on pollution can be achieved. A comparison of a typical sinter with a sinter produced through the utilization of waste materials showed a distinct correlation between certain types of waste material and some metallurgical properties. Dolochar in a sinter blend acts as part of the fuel and flux that are normally added to a sinter mix. Generally dolochar improves the quality of the sinter and decreases the consumption of coke. Other waste materials adversely influence the quality of the sinter. The glass and calcium ferrite content of a sinter when dolochar is used in the blend is similar to that of a sinter produced with only coke as a fuel in the sinter mix. The glass content is lower and the calcium ferrite content is higher, in a sinter produced from dolo char in the blend compared to a sinter produced with additions of other waste materials. Changes in the mineralogical composition are related directly to the metallurgical properties of the sinter product.

Jan 1, 1991

By Biserka Lucheva, Tzonio Tzonev

"Recycling of aluminum scrap and dross is significant in the economic and energy saving, as well as in the environmental protection. Recovery of metal aluminum depends on many factors. The aim of this work is to investigate experimentally the metal recovery under different conditions. The processing of aluminum dross was carried out in DC electric arc rotary furnace. The optimal technological parameters are determined. It is turned out that the presence of crushing refractory bodies during the processing of the aluminum dross in the rotary furnace increases the degree of aluminum recovery with about 10 %.IntroductionCompact and granular aluminum dross are used for the fulfillment of the experiments, which were obtained by salt free melting of aluminum scrap. The only preliminary preparation of the compact dross is crushing them into proper size, in compliance with the size of the opening for furnace charging and removing of fraction – 1 mm. The granular dross is subjected to sieving also with the purpose to remove the fraction – 1 mm. In these conditions the content of the metal phase in the compact dross is 72 %, and in the granular – 77 %. The processing of aluminum dross was carried out in DC electric arc rotary furnace (Figure 1).The purpose of this research is to investigate experimentally the metal recovery under different conditions and to establish the dominant factors, which need to be controlled."

Jan 1, 2008

By Andre Thess, Jurij Kolesnikov, Christian Karcher

"During the motion of molten metal under external non-homogeneous magnetic field the induced electric currents produce Lorentz body forces in the opposite direction to the flow, causing deformation of velocity profile, vortical structures, and adding a pressure drop across the magnetic field. The same Lorentz force acts on the magnet system. We analyse these phenomena in metallurgy, namely, at molten metal pumping, stirring, continuous casting, and in contactless Lorentz force flowmeter (LFF). Experiments with liquid metal alloy, including direct measurements of Lorentz forces, velocities, and flow structure visualization were conducted. Based on this study the industrial prototypes of LFF systems were designed, built, and tested in a secondary aluminium production. A molten metal flow at high temperature (700°C-850°C) can be effectively measured. The LFF technique method allows measuring precisely the volumetric and mass flow rates linked with Lorentz force, and the mass accumulated within production process.IntroductionThe present work demonstrates the development of a non-contact electromagnetic system for measurement of a liquid metal flow. Our approach embodies the Lorentz force velocimetry [1-6] technique which is physically based on a measurement of the force acting on an external magnet system the field of which interacts with the flow. This force is exactly equal to the braking Lorentz force induced in a flowing conducting fluid. In what follows a measurement system based on the Lorentz force velocimetry principle. For monitoring and controlling the production process it is desirable to measure continuously the mean velocity of the liquid metal in order to deduce the mass-flux and volume-flux from it. The form and dimensions of the magnet system are in agreement with geometry of the operating channel. We consider here a version of magnet systems in a composition of permanent magnets.The LFF possesses a number of advantages which make it attractive for the measurement of flows in hot and aggressive melts. The relation between the measured force and the desired volumetric flow rate is often linear (for closed channel or at a constant liquid metal level in open channel). For the converting of the measured force into volumetric and mass flow rate we should know the calibration factor. The calibration factor is independent of the viscosity and density of the liquid metal and depends only on the magnetic field magnitude, the electrical conductivity of the liquid metal and the geometry of the channel in which the liquid metal flows. In aluminium production, for instance, there exists a number of standard alloy compositions having welldefined conductivities for which the calibration factors can thus be tabulated. We consider below consistently effects in liquid metals arising under influencing magnetic field, construction principle of LFF and measurements of metal flows at industrial conditions."

Jan 1, 2011

By Tseng. B. H.

Samples of unchlorinated and chlorinated carbonaceous concentrate from a carbonaceous gold ore were analyzed by transmission electron microscopy (TEM) for organically bonded sulfur and chlorine. The concentrate assayed 1.53 oz/t gold and 6.01% organic carbon. Much of the organic carbon occurred as sizable coarse particles up to several hundred microns in size, which showed no visible evidence of reaction with chlorine after chlorination treatment. Both the untreated and chlorinated fractions of the carbonaceous concentrate were analyzed by the TEM method, which detected organically bonded sulfur in all of the carbon particles examined in the untreated sample, ranging from about 1 to 5% organic sulfur, and averaging near 3.1%. TEM analysis of 40 carbon particles in the chlorinated sample indicated that organic sulfur was reduced significantly in the carbon and replaced in part by the chlorine, as the result of chlorination.

Jan 1, 1987

By Bo Zhou

During secondary aluminum recovery, complex aluminum scraps are melted and refined often in a rotary melting furnace and the aluminum metal has to pass through a molten salt layer and melt down in a bottom aluminum bath. Previous experimental study and industrial observations have indicated that salt shell formation and re-melting on the metal solids in the early stage plays a critical role in the overall melting process of the scrap. In the present paper, mathematical models are developed to simulate the process of salt shell formation and its re-melting, as well as aluminum melting in the molten melt. Influence of the salt layer properties, the residence time of the metal particles in the salt layer, the particle size, the temperature of bulk melt were investigated. Reasonable agreement with the measurement data was reached. The developed melting model will be used to construct a population balance model of the scrap melting behavior for a rotary melting furnace, taking into account the distributed characteristics of the scrap. Finally, an overall process model based on Computational Fluid Dynamics (CFD) for the rotary furnace will be constructed, coupling with the population balance model for the scrap melting.

Jan 1, 2003

By Miroslav Raudensky, Kallol Bera, Jaroslav Horsky, Jee G. Chang, Ampere A. Tseng

"A combined experimental and finite element approach to study the local heat transfer coefficient is presented in this paper. The heat transfer coefficients at different cooling regimes in a roll are quantified by an inverse heat conduction technique; the heat transfer phenomena involved are then discussed. A discussion of the application of the heat transfer information found in the present study for better design of a roll cooling system is also included. Finally, an identification of areas where further work is needed is presented.IntroductionIn metal rolling processes, the roll is used as a tool to deform the workpiece at very high speeds. As shown in Fig. 1, the heat transfer phenomena involved in the process are complicated by the interaction between the roll and the strip, mainly including 1) the heat transferred from the workpiece to rolls in the contact regions, 2) the heat created in the interface due to the deformation of the workpiece and the friction between the workpiece and roll, and 3) the heat removed by watercooling as well as the ambient air. All of these transport phenomena occur at extremely high pressure, high speed, and high heat flux; these make the control of the roll temperatures an extremely challenging problem.In hot rolling, proper cooling of rolls can lead not only to improve the roll shape quality by controlling the thermal crown of the roll, but also to extend the roll life by minimizing the thermally induced stresses [1,2]. Also, knowledge of roll temperatures can contribute to insights about the roll/workpiece interfacellubricant behavior, and lead to the desired surface condition of the workpiece. Therefore, adequate roll cooling or control of roll temperatures is of critical concern to mill designers and process engineers. In order to have proper operation of the process, a good understanding of the influence of cooling practices on the roll is essential [3]."

Jan 1, 1994

By Jiao Li, WenhuiMa, KuixianWei, YongnianDai, Cong Zhang

The paper studied the diffusion process of nitrogen and characteristic distribution of iron impurities in the bottom of cast crystalline silicon ingot along the direction of crystal growth. According to the dynamics analysis of the decomposition of Si3N4 coating, the diffusion process of nitrogen into multicrystalline silicon ingot during casting process should be divided into three steps. The diffusion length of nitrogen in multicrystalline silicon ingot is 700 μm. The results of EDS analysis indicate that the distribution characteristic of iron in multicrystalline silicon ingot is concerned with the diffusion process of nitrogen in this length. Based on the above research results, the distribution model of iron in casting multicrystalline silicon ingot was established and verified by the experimental results.

Jan 1, 2015

By Laurentiu Nastac

"An advanced casting simulation-based optimization approach was applied in this study to assist in the improvement of the mold design of aerospace components made of A3 56 alloy. By using this approach, mold filling and solidification related defects (including macro-shrinkage and shrinkage porosity) were significantly minimized and hence it helped in cost reduction, performance enhancement and quality assurance of complex A3 56 cast parts.An experimental validation and detailed calibration procedures of the models for prediction of macro-shrinkage and shrinkage porosities were performed using A3 5 6 plates cast in fiiran-silica sand molds using the Prometal's Rapid Casting Technology (RCT) - mold printing technology. Correlations between Niyama values and the pore percentage were also developed. Thus, the severity level of shrinkage porosity can be determined via the Niyama criterion. Predictions were then compared with the macro-shrinkage and porosity measurements in plates of various plate thicknesses and in other commercial A3 56 casting components.IntroductionThis paper describes the process modeling approach used in the development of the mold design technology used to produce assist in the improvement of the mold design of aerospace components made of A356 alloy. Nova Flow&Solid™ software [3] was applied in this study. This casting simulation software was previously validated for several alloys including Ti, steel and superalloys [1-4]. The objective of this paper is to calibrate and validate the simulation software for A356 alloy sand mold castings. For this purpose, an experimental validation and detailed calibration procedures of the models for prediction of macro-shrinkage and microshrinkage (e.g., shrinkage porosities) were performed using A356 plates cast in fiiran-silica sand molds using the Prometal Rapid Casting Technology (RCT) mold printing technology. The details of the RCT technology are shown in Fig. 1 [5]. Prometal's RCT technology is used for rapid production of sand molds and cores directly from CAD files. The RCT technology relies upon ink jet printer technology to selectively bind the grains of sand to create three-dimensional sand molds and cores. Mold filling and solidification modeling as well as stress analysis are typically performed to properly design the casting and the rig system of each prototype component."

Jan 1, 2012

By O. Forsén

A new cell construction was designed for the study of the electrochemical behaviour of additives in conditions that simulate real copper, electrorefining. The behaviour of gelatine and thiourea was studied by applying different electrochemical methods, i.e. polarization resistance and voltametric measurements. In this study, individual galvanostatic electrolysis experiments were carried out for 120 hours. The organic additives were introduced to the electrolyte at certain intervals and their concentration was varied in the range &om zero to four ppm. An optical microscope was applied for the examination of copper cathode deposit microstructures. The results show that gelatine has a polarizing effect on the deposition potential of copper whereas even small amounts of thiourea depolarize the electrodeposition of copper. The maximum inhibitor efficiency of gelatine was obtained at a gelatine concentration of slightly lower than two ppm. When both gelatine and thiourea were present in the electrolyte, the depolarizing effect of thiourea exceeded completely the polarizing effect of gelatine. If chloride ions were added to gelatine and thiourea containing electrolyte, the electrochemical behaviour of the system was altered drastically. Chloride ions resulted in the prevailing of polarization effect caused by gelatine while the depolarizing effect of thiourea disappeared in this system. The polarizing effect of gelatine increased until chloride ion concentration of 30 ppm was reached. Also, the above electrochemical phenomena could be detected in the optical examination of copper deposit microstructure.

Jan 1, 1995

By D. Norman, D. J. Hughes, R. Dashwood, I. McGregor, N. D. Raath

"This paper develops a methodology for predicting spot weld fractures in automotive boron steel grades, such that fracture modes can be predicted accurately in a vehicle or sub-assembly structure. To achieve this, it was necessary to understand the range of complex fracture modes observed in boron steel spot welds and how these are linked to the Heat Affected Zone (HAZ) microstructures and hardness distributions and residual stress.Material data for the HAZ was extracted by simulating the spot welding process using a Gleeble machine; achieving specific weld microstructure in a larger volume which was used in destructive testing. Neutron diffraction was employed to accurately characterize the post-weld residual stresses found inside the weld. The constitutive relations of specific areas in the HAZ where fracture is thought to occur is being incorporated into finite element software to improve fracture prediction of boron steel welds.IntroductionWith the drive for light-weighting and improving passenger safety, lighter and stronger materials are being continuously sought in the automotive industry. The application of boron steel in the Body-In-White (BIW) meets both these criteria by down-gauging thickness of the steel and increasing the strength. As an example, when applied to crash-relevant areas in cars, components have an ultimate tensile strength of 1500 MPa, minimum springback and reduced sheet thickness.To achieve high strength and low springback, boron steel components must be formed and hardened at the same time. This is typically achieved by austenitizing the steel around 900 °C and simultaneously quenching and forming, usually with a hydraulic press and tool-set. Trace amounts of boron, typically 0.005wt%, increase the hardenability of the steel dramatically. This is attributed to the grain boundary segregation of boron, which hinders the formation of ferrite during cooling and forces the transformation of austenite to martensite at high cooling rates, a minimum of25 °C/s."

Jan 1, 2013

By H. Kurokawa

Sumitomo Metal Mining decided to expand copper production capacity of Toyo Smelter and Refinery to cope with the recent copper demand growth in Asia, and to survive by reducing cost. The expansion plan is promoted to increase electrorefined copper production capacity from 270,000 metric tons in 2001 to 450,000 metric tons in 2007. The major changes in smelting section are introduction of the rotary steam dryer, renewal of the feeding system for flash furnace, improvement of the concentrate burner, modification of the flash furnace cooling materials, renewal of the slag cleaning furnace, modification of the flash furnace waste heat boiler, installment of a new converter furnace, enlargement of two anode furnaces. In addition, the gas cleaning system was upgraded and the second acid plant was installed. In the refinery section, the existing tank houses have been operated at high current density of 300A/m2 using the conventional starting sheet cathode technology and moreover a new tank house utilizing the permanent cathode technology was constructed. Although the copper production capacity has been increased, SO2 emission has been kept the lowest in the world through consideration of influence on the environment by expansion project.

Jan 1, 2006

By C. Zografidis, K. Karalis, E. Devlin, S. Tabouris

"The main parameters affecting energy and electrode consumption in smelting reduction of Greek nickeliferous laterites in submerged arc electric furnaces (E/F) were investigated. Within this framework, the operational data of E/Fs, such as energy consumption indicators, electrode consumption indicators and chemical characteristics of Fe-Ni and slag, were correlated with the physicochemical characteristics of the calcine, produced by roasting reduction of laterite in rotary kilns (R/Ks), such as reduction degree, temperature, chemical composition and granulometry. The results obtained provide a significant input for further research on the modelling of the roasting reduction – smelting reduction process, which is a critical tool for energy optimization.IntroductionThe two main steps of pyrometallurgical treatment of greek nickeliferous laterites for ferronickel production include: i) drying, pre-heating and controlled pre–reduction of laterite ores with solid fuel reducing agents and fuel oil in rotary kilns (R/Ks) for the production of a calcine, and ii) smelting reduction of the calcine in open-bath submerged-arc electric furnaces (E/Fs) for the production of Fe-Ni alloy with 12-16% Ni [1].The energy absorbed from the endothermic reductive reactions of iron, nickel and cobalt oxides (Fe2O3, FeO, NiO and CoO) of the calcine with the remaining carbon in the E/Fs, corresponds to about 16% of the total energy output in the smelting reduction step [1]. This is indicative of the significance of the calcine’s reduction degree for the electric energy requirements in the E/Fs. Moreover, the chemical characteristics and the granulometry of the calcine constitute critical parameters for the energy requirements as well as the smooth operation of the E/Fs."

Jan 1, 2012

By J. van Driel

NOx is a growing concern for acid plant operators due to recent legislation reducing the allowable stack limits, as well as continually more stringent requirements for product acid quality. NOx also causes a major problem during maintenance as NOx rich acid residues fume following exposure to moisture in the air. Until recently, the solution for NOx related issues was to treat the symptom, rather than the cause. NOx in product acid was treated using chemicals and the NOx in the plant stack was generally left untreated. As part of an environmentally driven change in concentrates, Budel Zink installed the first gas phase NOx destruction process to be incorporated into a commercial scale acid plant. Nitrogen oxides contained in the process gas are reduced selectively with ammonia over a catalyst to form nitrogen and water. As a result, the NOx reduction is in agreement with the permit requirements.

Jan 1, 2002

By G. Van Weert

The pellet reactor was developed approximately 20 years ago in the Netherlands for softening drinking water. Since then, some 35 plants have been built, ranging in capacity up to 8500 m3/h. Applications now also include removal of phosphates and fluorides and the production of metal carbonates and sulphides from waste streams. The pellet reactor consists of a fluidized bed, wherein the process solution is thoroughly mixed with the precipitation reagent at special inlet nozzles to give over-saturation of the compound to be precipitated. In water softening applications, the compound is CaCO,. In the case of nickel or other metal waste streams, Na2CO3 solution is added in sufficient amounts to precipitate metal (hydroxy) carbonate on the fluid bed particles. These grow typically to dense spheroids, which are removed when they reach 0.8 to 1.0 mm diameter. These spheroids are easily dewatered, free flowing and low dusting. The latter property is becoming an attractive advantage in connection with new plant hygiene regulations. The operation of a 60 cm diameter pellet reactor on nickel containing plating waste is described and the properties of the produced nickel carbonate spheroids are discussed.

Jan 1, 1993