Search Documents

By Joël P. T. Kapusta, Romeo U. Pagador, Noparut Wachgama, Chumnoom Khuankla

"Thai Copper Industries (TCI) is a custom copper smelter and refinery in Rayong, Thailand, with an annual capacity of 165,000 tons of cathodes. It employs the El Teniente Technology as the primary smelting reactor to produce white metal from copper concentrates. The white metal is further treated in Hoboken Siphon Converters to produce blister copper then refined in anode furnaces before being cast into anodes for electro-refining in the on-site tankhouse.Thai Copper Industries is the first copper smelter to install and successfully operate on a commercial scale with the Air Liquide Shrouded Injection (ALSI™) Technology in the Hokoben converters with sonic injection of oxygen enriched air and nitrogen for cooling of the injector tip areas. Following commissioning and the establishment of operating practices, the performance of the Hoboken converters with ALSI™ Technology produced outstanding results. The unique combination of an El Teniente and Hoboken siphon converters, both of which are bath smelting operations, offers very high blowing and oxygen efficiencies. As a consequence, reverts recycling was accelerated with minimal build up on the mouth, end-plates or even below the siphon that is typical in Hoboken converters.These outstanding results in the Hoboken Siphon Converters with ALSI™ Technology helped the TCI Plant reach a production of about 75% of its capacity within four months despite the fact that the TCI staff is quite young and its converter know-how and experience are not yet fully developed."

Jan 1, 2009

By Tatsuro Ariyama, Michitaka Sato, Atsushi Sakai, Sumiyuki Kishimoto, Ryota Murai

"In order to achieve high pulverized coal injection operation in a blast furnace, optimization of the injection lance arrangement was carried out using an experimental furnace and mathematical models. To increase the injection rate of pulverized coal, it is required to raise the combustion efficiency of pulverized coal. It became clear that multi-point injection and the lance arrangement to avoid interference among the coal streams injected were so effective in increasing combustion efficiency. With these findings, the eccentric double lance arrangement has been newly developed.At NKK, Fukuyama No.4 Blast Furnace, after the improvement of the lance arrangement, the maximum injection rate reached up to 230 kg/thm and an average monthly record of 218 kg/thm was successfully achieved.IntroductionFrom the viewpoints of reducing the production cost of pig iron and prolonging coke oven life, high pulverized coal injection over 200 kglthm is actively pursued by ironmaking industries[1-2].Coal particles injected into the blast furnace are consumed by combustion in the raceway and also in-furnace reaction like solution-loss reaction (C + CO2 = 2CO). The amount of coal consumed by the latter process is determined by the carbon balance in the blast furnace and there is a limit. Therefore, to increase the injection rate, it is desirable to improve the combustion efficiency in the raceway. For these purposes, the optimization of the lance arrangement was examined by a hot model and mathematical models."

Jan 1, 1996

By Godwin Beene

During recent years, copper and acid production from Nkana Smelter has formed a significant proportion of ZCCM's total output, but a number of problems affecting the smelter over the last decade have only been recently overcome. This paper discusses recent developments in the smelting practice, highlighting some of the operational problems experienced and associated solutions. The smelter performance over the decade is discussed and the innovations in the smelting technology employed to sustain production in the wake of limited re-capitalization are dealt with in detail.

Jan 1, 1999

By Daojin Cao

The chemical components in the saturated aqueous solution of ammonium dimolybdate (ADM) were investigated at room temperature by comparative Raman spectroscopy. In order to explore the further detailed results, a new method of qualitative and half quantitative analyses, based on the main vibrant frequencies and the intensity ratio of the strongest peak to the second strongest peak recorded in Raman spectrum of saturated aqueous solution of ammonium heptamolybdate tetra hydrate (AHM), was put forward and attempted to analyze the chemical components of saturated aqueous solution of ADM. The results showed that there was obvious difference between Raman spectrum of saturated aqueous solution of ADM and that of ADM, but there were good relationships between Raman spectrum of saturated aqueous solution of ADM and Raman spectra of the three samples including AHM, the saturated aqueous solution of AHM and monomolybdate ion in aqueous solution. It was found that aggregated dimolybdate ion ({Mo2O72-}n)did not exist in the saturated aqueous solution, and was changed into heptamolybdate ion (Mo7O246-) and monomolybdate ion (MoO42-), which were in equilibrium each other, but the distribution ratio of heptamolybdate ion was larger than that of monomolybdate ion. In addition, Raman spectral pattern of saturated aqueous solution of ADM was reported.

Jan 1, 2006

By Neng-Wen Yu, Shau-Jun Zhu, Ji-He Wei

The desulfurization process by powder injection and blowing in the RH refining of molten steel and its mechanism have been considered and analyzed. Based on the two-resistance mass transfer theory and the mass balance of sulfur in the system, a kinetic model for the process has been developed. The related parameters of the model, including the mass transfer coefficients and the effective amount of powder in the molten steel being treated for desulfurization, have been more reasonably determined. Modeling and predictions of the process of injecting and blowing the lime-based powder flux under assumed operating modes with the different initial contents of sulfur and amounts of powder injected and blown in a RH degasser of 300 t capacity have been carried out using the model. The relevant circulation rate of the liquid steel and the powder injection and blowing rate were taken to be 100 t/min and 150 kg/min, respectively. The initial contents of sulfur in the liquid steel to be treated and the amounts of powder injection and blowing were respectively assumed to be 0.007, 0.006, 0.005, 0.004, 0.003, 0.002 mass-% and 10, 8, 6, 5, 4, 3 kg/t-steel. The total treatment time for desulfurization under each mode was set up at 24 min, equivalent to eight circulation cycles of the liquid steel to be treated. The results indicated that the predictions made with this model are in good agreement with some data of the industrial experiments and practice. Injecting and blowing the lime-based powder flux with the composition of 85 mass-% lime (CaO) + 15 mass-% fluorspar (CaF2) of 3-5 kg/t-steel, it is possible to decrease the sulfur content in the molten steel to ultralow level below (5-10)x10·4 mass-% from (60-80)x 10·4 mass-%. The total treatment time needed will appropriately be 12-20 min. Intensifying the powder injection and blowing operation and increasing the circulation rate of the liquid steel may effectively' raise the rate of the process in RH refining. The model may be expected to offer some useful information and a reliable basis for determining the reasonable process parameters and help in optimizing the technology of desulfurization by powder injection and blowing in the RH refining of molten steel.

Jan 1, 2000

By Nickolas J. Themelis

Nearly thirty two million tons of municipal solid wastes (MSW) are combusted annually in over one hundred U.S. Waste-to-Energy (WTE) power plants, thus reducing the use of fuel oil by about 1.6 billion gallons of fuel oil One of the advanced WTE processes is the 0.9-million ton/y SEMASS facility at Rochester, Mass. Most of the combustion in the three giant combustion chambers occurs while the injected shredded wastes are in suspension, i.e., in flash combustion mode. The velocity, temperature, and concentration profiles in the SEMASS combustion chamber were simulated by representing the combustible fraction of MSW by the simplified formula C6HIO04 and using the CFD program Fluent to solve the turbulent energy and mass transport equations. After validation against plant data, this model will be used to examine options for increasing the productivity of WTE combustion chambers, such as optimum distribution of primary and secondary air and oxygen enrichment.

Jan 1, 2003

By Junji Shibata

Through-hole copper plating is performed to make a multi-layer printed circuit board. The through hole plating is first carried out by Pd catalyst treatment, followed by copper non-electric plating. The amount of Pd catalyst used in one plant is about 0.25-2 m3/month (8 g/dm3 PdCl2 base) depending on the plant scale, and the cost of the catalyst reaches 17,000¬I35,000 US$/month. In this study, the flow and material balance of a Pd in Pd catalyst treatment process was investigated. About 60% of Pd catalyst adheres on the through-hole and other part of setup, while 25% is released into the washing liquor. Pd in the washing liquor should be collected by a suitable method like a pressure filtration using diatomite. The material balance of Pd in Pd catalyst treatment process and the recovery method of Pd from waste solution containing Pd catalyst was investigated.

Jan 1, 2003

By John A. Vallomy

"The CONSTEEL Process introduces a new concept in electric steelmaking by continuously feeding-preheating-melting and refining ferrous scrap or direct reduced iron. The process uses the furnace off-gas and fuel to preheat the scrap in a specially designed preheater. Thermal incineration of the flue gas reduces the carbon monoxide level to the more stringent requirements. Hot water or steam production from heat of flue gas is optional. The tap-to-tap time is set to match the cycle of the caster. The steel is treated via ladle metallurgy. The environment inside and outside of the steelplant is improved by decreasing levels of noise and hazardous emissions. Energy consumption decreases and disturbance to the electric network is eliminated. A CONSTEEL prototype was tested at Nucor Steel, Darlington, SC. A greenfield project is in the completion stage at the Florida Steel plant of Charlotte, NC, USA. The Process PhilosophyThe philosophy of the CONSTEEL Process is not solely to enhance efficiency; this was just a natural result of the change from a batch to a continuous practice. The primary objective in development was four-fold:1) 100% process control2) Rational use of available energy3) Improved environment inside and outside the plant4) Stability of energy input from the power systemIt was to make electric steelmaking more a science than an art and amenable to modern automation.The Basic Concept of CONSTEELThe concept of the process is shown in figure and includes basically a continuous feeding system, a preheater and a melting - refining furnace. A pre-established amount of heat is introduced into the scrap while traveling through the preheater using the sensible and chemical heat contained in the furnace off-gas and additional fuel. Melting-refining is carried out in the electric furnace. Slag formers, slag foaming additions and oxygen are injected to refine the melted steel continuously, to minimize the refractory erosion, to shield the arc, thus optimizing the transfer to the metal bath of the heat generated in the arc, to keep the bath homogeneous in composition and temperature and to produce carbon monoxide (CO) which is fuel for the preheater."

Jan 1, 1988

By Guo Chen, Yifeng Shi, Xiaobiao Shang, Nanshang Shen, Bangqi Zhang, Jinhui Peng, Junruo Chen

"The energy is introduced directly into the volume of the honeycomb ceramic regenerator due to the complex interaction of microwaves with minerals in microwave gas heating system. A three-dimensional numerical model is developed to simulate the electromagnetic field by solving Maxwell's equations using finite-difference time-domain method. Computational result is presented for the microwave power absorption of the regenerator. Effects of the dielectric constant and the effective loss factor on the microwave power absorption in the regenerator are studied as well. Numerical results show that the heating pattern strongly depends on the dielectric property of the regenerator. The demonstration of the model of electromagnetic field distribution can be applied effectively and efficiently to optimize the fundamental parameters in the microwave heating processing.IntroductionIn recent years, microwave energy has been utilized in many fields, such as food processing, chemical engineering and mineral processing [l]. In contrast to conventional heating, where heat is transferred from a surface to the interior, microwave energy is introduced directly into the volume of minerals due to the complex interaction of the microwave with the mineral. Based on volumetric heating effects, microwave heating has several advantages such as pollution free, rapid heating technique, internal heating, high efficiency over conventional heating [ 1-4]."

Jan 1, 2013

By Jannie S. J. van Deventer

Geopolymers are novel engineering materials with the potential to play a highly significant role in the transformation of the construction materials and building products industry in the push towards sustainable development. These materials are formed by activation of industrial aluminosilicate waste materials such as coal ash or blast furnace slag with alkaline solutions. Geopolymers derived from coal ash can exhibit superior mechanical properties and chemical stability when compared to ordinary Portland cement (OPC). The use of waste-based geopolymers can also result in significant (up to 90%) reduction in carbon dioxide emissions when used in cement replacement applications. In addition to the formation of conventional pre-cast products, these high performance mineral binders are ideally suited to use in the encapsulation of mine tailings, immobilization of heavy metals and back-filling of mines due to their chemical stability and resistance to acid attack. A key attribute of geopolymer technology is the robustness and versatility of the manufacturing process; it enables products to be tailor-made from a range of raw material sources (waste and/or virgin) with specific properties for a given application at a competitive cost. Despite these key technical and environmental attributes, it is the ability to add significant value to coal ash or and/ or metallurgical slag waste streams which drives the commercial development and uptake of the technology.

Jan 1, 2006

By Supachai Surapunt

The distribution behavior of V A minor elements (As, Sb and Bi) in the smelting stage of the Mitsubishi process were evaluated thermodynamically based on thermodynamic data and operating data. The fractional distributions between the gas, slag and matte phases considered as the degree of vapor saturation of 1.0 are as follows: 53.8, 27.2 and 19% for As, 23.6, 56.6 and 19.8% for Sb, and 91.3, 1.1 and 7.6% for Bi, respectively. Arsenic is mostly distributed to the gas and slag phases. It is effectively eliminated by volatilizing and slagging. Antimony is mainly in the slag phase, which is suitably removed by slagging. Bismuth is easily vaporized to gas phase. The degree of vapor saturation has a large effeet on the distribution behaviors of the three elements between the three phases. The amount of a minor element in the charge has an effect on the distribution of As but no effect on the distributions of Sb and Bi. Increasing matte grade and temperature results in the change of distributions for As and Sb, significantly. The change in the distribution ratio between slag and matte phases also considerably affects the distributions of As and Sb. The distribution behavior of Bi is not significantly changed by the change in matte grade, temperature and distribution ratio.

Jan 1, 2003

By Supachai Surapunl

The distribution behavior of VA minor elements (As, Sb and Bi) in the smelting stage of the Mitsubishi process were evaluated thermodynamically based on thermodynamic data and operating data. The fractional distributions between the gas, slag and matte phases considered as the degree of vapor saturation of l.0 are as follows: 53.8, 27.2 and 19% for As, 23.6, 56.6 and 19.8% for Sb, and 91.3, l.1 and 7.6% for Bi, respectively. Arsenic is mostly distributed to the gas and slag phases. It is effectively eliminated by volatilizing and slagging. Antimony is mainly in the slag phase, which is suitably removed by slagging. Bismuth is easily vaporized to gas phase. The degree of vapor saturation has a large effect on the distribution behaviors of the three elements between the three phases. The amount of a minor element in the charge has an effect on the distribution of As but no effect on the distributions of Sb and Bi. Increasing matte grade and temperature results in the change of distributions for As and Sb, significantly. The change in the distribution ratio between slag and matte phases also considerably affects the distributions of As and Sb. The distribution behavior of Bi is not significantly changed by the change in matte grade, temperature and distribution ratio.

Jan 1, 2003

By Masahiro Yoshimura, Sergiy Korablov

"Hydi-othermal corrosion ofTiN, TlAlN and CrN PVD films (3 µm thick) deposited on SUS-304 substrate was studied in 100MPa water in 20-950°C temperature range up , to 750h. The beginning temperature of their reaction was determined as 200°c for TiN and TiAlN and 500°C for CrN films, which are quite low in comparison with that of air oxidation of those powders. Very thin oxide scales. of TinO; n-I homologous series phases were formed above 300°C. TiO2 anatare. is observed for TIN and TiAlN films at 400°C. The· feature of hydrothermal corrosion of CrN films seems to be CrNxOy phase formation.Distinguishable weight changes were observed at higher temperature than 700°C for TiN, 750°C for· TiAlN and 800°C for CrN respectively. Hydrothermal corrosion kinetics .was constructed to calculate the activation energy of hydrothermal corrosions. On the base of obtained data, hydrothermal corrosion resistance was as follows: TiN – TiAlN - CrN. Facetted oxide crystals were formed at higher temperature than 500°C for TiN, TiAlN and 850°C forCrN.IntroductionThe metallic nitride (TiN; TiAlN, CrN) PVD films have high hardness, strength and wear resistance. Therefore these films are widely used in industry for wear resistij.nce application such as cutting tools and die molds. Their performances depend on not only the mechanical properties but also corrosion resistance of coated films. High temperature oxidation of metalliq nitride and nitride films was well studied [1-5]. However there are no reliable data concerning the .corrosion resistance of coated nitride materials. In high-temperature and high-pressure water. There are a few reports on hydrothermal corrosion of nitride films [6,7]. The increase of corrosion resistance of CVD films was observed in following succession TiC - TiCNO - TiCN - TiN at 300-680°C temperature interval and I 00 MPa pressure water according to data of the first report. Kawana et al. [7] have reported about excellent corrosion resistance of CrN films under 290°C and 8, 6 MPa water during I 000 h in the circulating type experimental loop. The films thickness was about 7-10 µm in both cases. However it remains unclear the chemical state of the surface species and especially in-depth distribution, oxide scale thickness and its growth, and defects formation in the oxide film."

Jan 1, 2000

By Ryokichi Shimpo

Much amount of sludge is produced from the wastewater treatments in surface finishing industry. There are many problems for the abandonment of the sludge because of the high water content and heavy metals included. It is often observed that hexavalent chromium, which is toxic, is generated in the course of heat treatments of the sludge for reducing its amount by dispersing water. In this study, conditions of the sludge calcinations for reducing water contents have been examined. Maximum hexavalent chromium generation was observed in the temperature range around 773 K, at which most of the crystallization water decomposed from the sludge. When the heating temperature became higher than 1173 K, the amount of the hexavalent chromium extracted from the calcined sludge became as low as 10 mg/kg sludge. When the sludge was heated with iron oxides, FeO or Fe203, iron ferrite has been synthesized which may be used as a magnetic material. The amounts of hexavalent chromium generated in the heat treatment with iron oxides were not much different from those without iron oxides.

Jan 1, 2003

By Toshiyuki Nohira, Eiichi Takeuchi, Tetsuo Oishi, Hideki Ono, Hirokazu Konishi

The Dy-Nd-Pr-Ni alloy sample was prepared by cathodic potentiostatic electrolysis at 0.65 V (vs. Li+/Li) for 1 h using a Ni plate in a molten LiCl-KCl-DyCl3-NdCl3-PrCl3 system at 723 K. The highest mass ratio (Dy/Nd+Pr) in the alloy sample was observed to be 50 at 0.65 V. Anodic potentiostatic electrolysis at 2.20 V for 12 h was conducted using the Nd-Fe-B magnet electrode in a molten LiCl-KCl system. All elements were almost dissolved from the magnet, and the original form of the magnet disintegrated. After anodic potentiostatic electrolysis at 2.20 V, cathodic potentiostatic electrolysis was conducted at 1.00 V for 5 h using a Mo plate in order to remove the dissolved Fe from the bath. Finally, cathodic potentiostatic electrolysis was conducted at 0.65 V for 12 h using a Ni plate. The mass ratio of Dy/Nd in the alloy sample was determined to be about 18.

Jan 1, 2015

By Markus A. Reuter, Robert Matusewicz

"Consumer products are a complex man-made mixture of sometimes in excess of 50 elements. In order to recover these complex mixtures of elements either as metals, compounds or energy requires versatile technology in physical separation but also smelting and energy recovery. This paper explores this by referring to the innovative application of Top Submerged Lance (TSL) technology and associated theoretical and environmental aspects to process (recycle) post consumer materials and industrial intermediate products and residues. A diversity of applications has been tested in Ausmelt’s pilot plant in Dandenong and many have gone to commercial scale globally. This paper reviews the varied applications ranging from e-waste recycling, lead and NiCd battery recycling, metals recovery from slags, zinc leach residue processing, electric arc furnace (EAF) dust, Municipal Waste Incinerator bottom ash processing, carbon containing residues such as retort ashes and spent pot liner from the aluminium production process as well as use of the technology for materials such as automotive shredder residue (ASR) and plastics. Introduction The modern resource cycle is a link between primary production of metals linked to the recycling of post-consumer goods. The sometimes complex combinations of materials and metals in consumer products such as televisions depicted by Figure 1, does require a range of technology to recover materials, metals and energy for reuse and/or recycling in an economically feasible as well as environmentally friendly manner."

Jan 1, 2008

By Jiechao Liu, Lijian Luo, Yubao Ma, Bo Zhang, Yanfeng Yang, Xin Hong, Luming Liu, Jienan Liu

Reduction kinetics of stainless steel slag in iron bath smelting reduction was studied at the temperature of 1500℃ ~ 1650℃. It was concluded that the reduction process consisted of two parts. That is to say smelting reduction was controlled by stainless steel slag melting initially and by interface reaction later. In order to increase smelting reaction rate, the melting point of slag should be decreased at the first stage and adjust the liquidity of slag at later stage. Smelting reaction rate will be accelerated by means of optimize the slag content. The optimal reduction result that all most all of the chromium in slag been recovered was obtained in temperature was 1500℃, basicity of slag was 1.0~1.2, the value of Al2O3+MgO was 25%.

Jan 1, 2015

By Alexander V. Derevyanko, Victor P. Popov, Alexander I. Raitchenko

"If an electric current flows along some electroconductive suspension in columnar form the solid particles are 'experienced thermal, mechanical, and electromagnetic influences.The objects were suspension Sn (liquid) - Ni-Cr-Mo-W alloy (solid particles). This is refractory alloy on the Ni base. The direct constant current (with density -106 A/m2 ) flowed through the named suspension during 180+300 sec. At the beginning of experiments samples were ones containing particles suspended uniformly in volume. Although density of solid particles was ~9x103 kg/m3 , i. e. higher than density of liquid Sn (-6.8x103 kg/m3 ), after end of this processing, the non-uniform distribution of particles in volume of samples was observed: concentration of Ni-alloy particles in lower part was smaller than their concentration in upper part of samples, and simultaneously their concentration is increased near outer surface. There was probably the natural convection of Benard-Rayleigh type which had carried, so lid particles upwards, and, in same time, there was the action of spatial Lorentz-forces directed to center forcing the radial movement.The knowledge of named phenomena can be useful for elaboration of technology of gradient dispersed materials and development of some materials science fields.IntroductionThe liquid metal with the electric current or under the alternating magnetic field is experienced compression. This action causes the pressure within metal and the change of the surface of the metal column (see, for example, [1-4]). One of results of such an electromagnetic compression is extraction of the foreign solid particles from a cylindrical liquid sample to surface in the radial directions. However, more complicated paths of the inclusions are observed under some conditions of electric treatment."

Jan 1, 1999

By Kazuyoshi Sato, Keizo Uematsu, Nozomu Uchida

"Confocal fluorescence scanning laser microscope was applied to characterize the surface flaw of ceramics in great detail. A high potential -of the characterization technique is presented first. Then the technique was applied to clarify the relationship between the flexural strength of ceramics and the surface flaw. This kind of direct information of surface flaw should be essential for the fundamental study in this area, but has been lacking. The examination revealed that large defects are present on the machined surface of ceramics. Their size is consistent to the flexural strength measured on the material. The characterization tool was also applied to examine the formation of surface flaw in machining of ceramics.IntroductionClarification of fracture origin should be the starting point in the study on strength in ceramics. However, this task has been extremely difficult in some ceramics, such as an alumina ceramics. It may break from both internal and surface flaws. The former should reflect the quality of production process and the latter the machining. Examination of surface flaws should be very important for developing a better machining method for ceramics. The knowledge may valuable for establishing a better production process also.ExperimentAlumina Referceram (JFCC) was used as samples. They are cut to size of 3x4x40mm, and the surfaces were ground to meet the requirements of testing method for flexural strength of fine ceramics, JIS R 1601. They were soaked in an aqueous solution of fluorescence dye and evacuated with an aspirator for an hour to allow the solution penetrate into surface flaws. After excessive solution remained on the surface was removed by gentle washing, the specimens were dried at 120°C for 48 hours. The 4 point bending mode was applied to measure the fracture strength."

Jan 1, 2000

By B. Q. Li, S. P. Song

"Numerical models are developed to represent complex electromagnetic, free surface deformation and fluid flow phenomena in floating zone refining processes with radio frequency inductive heating. The computational methodology is based on the coupled finite/boundary element method for the electromagnetic field distribution and the Galerkin finite element method for magnetically driven fluid flow and free surface profiles of the molten zone. With the models, the complex transport and free surface phenomena in a floating zone system can be studied as a function of various operating conditions including applied current, frequency, inductor position and shape, surface tension, floating zone diameter and height. Results show that the equilibrium shape is sensitive to the height of the molten zone and that the free surface shapes can have a significant effect on the melt flow in the molten zone. Our extensive simulations also suggest that to ensure accurate results, the same mesh should be used, whenever possible, for both the electromagnetic forces and fluid flow calculations.1. IntroductionThe floating zone processes have been widely used in the materials industry to grow ultra-pure rare earth metal or semiconductor single crystals for sensor or electronic applications that have a tough demand on purity. Developed based on the principle of magnetic melting/levitation, the processes possess a main advantage that the molten zone is supported in air by the electromagnetic forces generated by the coil (see Figure 1), and therefore is free from contamination from a container. Consequently, the final products made from the floating zone processes have higher inherent purity than those by other techniques [1-4].Complex physical phenomena occur in the floating zone processing of materials. These include free surface deformation, magnetically-driven melt flow, which may be turbulent or mildly turbulent [5] depending on the applied conditions, and solidification. Thermal stresses also develop in the single crystals, which are affected by the flow and temperature field and which can have direct implications to qualities of single crystals [6]. An understanding of the fundamentals governing these physical phenomena can be of critical value in elucidating the physics that controls the properties of the metal or semiconductor crystals being produced, thereby providing a rational basis for process improvement and quality control."

Jan 1, 1997