Search Documents

By lchiro Aoi, Hideo Nakae, Makoto Yoshida, Makoto Ishino

"The influence 6f gravity on the microstructure of unidirectionally solidified Cu-Pb monotectic, Ag-Si and Fe-C eutectic alloys is studied. In order to examine the influence of gravity in a lg environment, both the upward (opposite to direction of gravity) and downward (direction of gravity) unidirectional solidifications are carried out. The results are as follows: (1) For the upward solidified Ag-Si eutectic alloy, the eutectic Si continuously grows. On the other hand, in the downward solidified Ag-Si alloy, the Si grows discontinuously and disperses into the ex-Ag matrix. (2) No morphological difference in the eutectic growth is observed between the upward and downward solidified Fe-C eutectic alloys. (3) In the case of the upward solidified Cu-Pb monotectic alloy, a banded structure, which consists of Pb-rich layers and Cu-rich layers, is observed. However, such a banded structure -is not observed in the downward specimen. (4) The banded structure is not found in the upward solidified Cu-Pb-0.05 mass % Al and Cu-Pb-0.1 mass % Al alloys. In the Cu-Pb-0.05 mass% Al alloy, a fibrous -L 2 phase grows continuously parallel to the growth direction at low growth rate. Only 500 mass ppm addition of aluminum induces the morphological change of the monotectic L2 phase.IntroductionThe influence of gravity on the solidification of eutectic and monotectic alloys has been investigated in microgravity environments [l-9]. The purpose of these studies was to obtain a homogeneous microstructure of eutectic or monotectic alloys, most of which alloys tend to solidify with macro-segregation under gravity. However, in most of the previous experiments, e.g., in free fall systems, in aircraft or in space laboratories, the growth rate was too high to realize a planar solid/liquid interface. This would be due to the limited time for solidification. Thus, it was difficult to examine the influence of gravity on the planar coupled growth of the eutectic or monotectic alloy. In this study, both the downward U.D.S. (unidirectional solidification by gravity) and upward U.D.S. (opposite direction to gravity) are carried out in order to examine the influence of gravity on the coupled growth in a lg environment [l0, 11]. In the case of the downward U.D.S. using the current Bridgman method, the molten alloy must be confined between the crucible and the solid."

Jan 1, 2000

By Bob Drew, Alfred Spanring, Kirschen. Marcus

"Increasing material conversion and energy efficiency, and decreasing carbon dioxide emission levels are crucial for sustainable production processes in the aluminum, cooper, and steel industries. RHI supports these targets by providing a diverse range of solutions including high quality refractory linings, optimum lining maintenance, and process improvements. In this paper examples are provided of process improvements and increased energy efficiency in copper refining, potential energy savings during electric arc furnace and ladle operations in the steel industry, and increased energy efficiency by improved heat transfer in anode baking furnaces in the aluminum industry. In all cases, RHI’s expertise in close collaboration with the customer resulted in an improved performance of the reactor lining and the actual high temperature process with a positive impact on the material conversion and energy efficiency and as a result a decrease in specific carbon dioxide emission levels.IntroductionRefractory linings play an important role in heat transfer during high temperature processes in for example the aluminum, copper, and steel production industries. Due to constantly increasing energy prices worldwide and the increasing demands for environmental and climate protection, improving the energy efficiency and decreasing emission levels of these energy intensive production processes is of significant importance. In this paper, the contribution of modern RHI lining technologies to energy saving measures and the corresponding reduction of specific carbon dioxide emission are described. The type of current refractory solutions for energy intense processes are illustrated with four examples: Optimization and increase of material conversion and energy efficiency in copper refining, energy saving potentials in both electric arc furnace and transport ladle operations in the steel industry, and heat transfer improvements during the carbon anode annealing process in the aluminum industry. These examples focus on particular production processes operating with a high proportion of recycled copper, steel, and carbon anodes. Increased energy efficiency directly decreases the specific energy related carbon emission levels whereas improvements to the metallurgical processes aim to increase material conversion efficiency and, therefore, decrease specific process related carbon emission levels. Significant energy savings can be achieved by maximizing the refractory campaign length through a combination of appropriate refractory material selection, grade zoning, correct installation, careful preheating, and effective maintenance strategies. Besides the efforts to improve the performance and energy efficiency of customer high temperature processes, RHI continuously promotes the development of new low emission carbon-containing refractory bricks and unshaped products."

Jan 1, 2008

By Jack S. McPartland

The recent developments on the concentration and recovery of gold from leached gold thiosulfate solutions by solvent extraction, reduction-precipitation, and electrochemical deposition are reviewed in this paper. Alkyl phosphorus esters have been found to extract gold only in alkaline thiosulfate solutions, The recovery of gold increases with thiosulfate concentration in the aqueous phase and with alkyl phosphorus esters concentration in the organic phase with aliphatic hydrocarbon diluents. The addition of ammonia improves the extraction. The extraction of gold with amines in either aliphatic or aromatic diluent decreased in the following order: primary>secondary>tertiary amines. Increase in the extractant concentration at high pH increased the extraction of gold. At pH < 9, the primary amine, RR&apos;CHNH2 with 1&apos;9-23 carbon atoms is the main extractant with TBP as the synergistic reagent and at pH >9, the primary amine shows a synergistic effect on the extraction of gold&apos; with TBP. TheAu(I) ions in thiosulfate solution are reduced by sodium borohydride (SBH) to metallic gold, with particles in the sub micron range, At an SBH/ Au ratio of 6.25, pH = 6, and at room temperature, the I e ppm Au(I) in a solution of ] 0 gil thiosulfate was completely reduced to metallic gold in about 60 minutes.

Jan 1, 1999

By Y. C. Avniel, T. E. Warner

"It is important to be able to measure sulphur and nitrogen in molten iron and steel on-line. Unfortunately, there are no solid electrolytes which are stable under oxidising conditions and in which the ions of these species are mobile. In this paper, novel applications of beta alumina electrolytes are described and the results compared with data in the literature. Excellent agreement was obtained confirming this approach as a viable method of detecting elements whose ions are not mobile in solid electrolytes.IntroductionIn the past two decades, the rate of many processes in steelmaking have increased substantially. The sophistication of chemical analysis has also increased but analytical equipment is frequently positioned a significant distance from the operating plant which dictates that time is spent taking a sample, sending it to the analytical facility, preparation of the analytical sample prior to insertion into the equipment. In many cases, the time taken for analysis can exceed the time taken for the actual process and is now the rate defining step. Furthermore, most analytical methods are unable to distinguish between the amount of element which is dissolved in the steel and that contained in precipitates. Even if the analytical equipment could separate these two, the distribution would have changed between the molten steel and the cast sample. It would be an advantage to analyse on-line for impurities in molten metals."

Jan 1, 1997

Rotary kiln incinerators are widely used in the incineration of various types of hazardous wastes. However, the complex transport processes within the incinerator are not well understood. Due to large variations in waste types and difficulties in feed characterization, the incineration process meets great challenges in a smooth operation, and expects uncertainties in the process chemistry and emission control. In order to get better understanding of the incineration process, process simulation was made on the kiln behavior by using Computational Fluid-dynamics (CFD) to characterize gas flow, temperature distribution and waste combustion in the incinerator. Temperature measurement was conducted in an operating incinerator to validate the CFD model. This paper addresses the environmental issues related to the hazardous incineration process, and reports the recent simulation results on gas flow and mixing, combustion heat transfer, and potentials to reduce emissions.

Jan 1, 2002

By Hector Henao

To provide thermodynamic data for converting the nickel matte to liquid nickel, an experimental study was conducted in the phase equilibrium between the Ni-S alloy and the CaO-Ah03 based slag melted in a MgO crucible at 1873 K under controlled Pso2 of 10.1 kPa and pO;, in a range between 2.5x,IO,2 and 10.1 Pa by using CO-C02-S0Z gas mixtures. The content of nickel in the slag at POz of 10.1 Pa, above which solid NiO is expected to precipitate in the equilibrium state, was found to be 4.1 mass% and the contents of sulfur and oxygen in the nickel melt were 0.4 and 0.2 mass%, respectively. It was clarified that increase in the temperature reduces the solubility of nickel in the slag and the contents of sulfur and oxygen in the alloy. The distribution of minor elements such as gold, silver, copper, cobalt, iron, arsenic and antimony between the Ni-S alloy and the CaO-AI20) based slag was also studied. The distribution ratios of iron and cobalt, defined by (%X in slag)/[%X in alloy] where X is the minor element, are larger values than that of nickel, while those of copper, silver and antimony are similar to that of nickel. The distribution ratios of arsenic and gold are lower than that of nickel in the higher range of oxygen partial&apos; pressure.

Jan 1, 2003

By Hector Henao

To provide thermodynamic data for converting the nickel matte to liquid nickel, an experimental study was conducted in the phase equilibrium between the Ni-S alloy and the CaO-Al2O3 based slag melted in a MgO crucible at 1873 K under controlled Pso2 of 10.1 kPa and Po2 in a range between 2.5x 10-and 10.1 Pa by using CO-CO2-SO2 gas mixtures. The content of nickel in the slag at Po, of 10.1 Pa, above which solid NiO is expected to precipitate in the equilibrium state, was found to be 4, I mass% and the contents of sulfur and oxygen in the nickel melt were 0.4 and 02 mass%, respectively. ft was clarified that increase in the temperature reduces the solubility of nickel in the slag and the contents of sulfur and oxygen in the alloy, The distribution of minor elements such as gold, silver, copper, cobalt, iron, arsenic and antimony between the Ni-S alloy and the CaO-Al2O3 based slag was also studied. The distribution ratios of iron and cobalt, defined by (%X in slag)/[%X in alloy] where X is the minor element, are larger values than that of nickel, while those of copper, silver and antimony are similar to that of nickel. The distribution ratios of arsenic and gold are lower than that of nickel in the higher range of oxygen partial pressure.

Jan 1, 2003

By R. Abel F.

In 1997, Ventanas electrolytic refinery expanded its production capacity from 215,000 to 325,000 metric tons per year. This increase in capacity has involved the treatment of anodes with different impurity contents, changing the operational strategy of the plant. On the other hand, the increasing necessity to accomplish environment conservation rules and quality assuring requirements, has led the plant operation and administration to compete in an advantageous way. The present work describes the results obtained in the startup and in the operation of the ENAMI Ventanas electrolytic refinery expansion, and shows the difficulties which have been faced in the processing of anodes of increasing complexity, in a competitive market and with environment and quality restrictions.

Jan 1, 1999

By V. B. Telles, J. A. S. Tenorio, J. O. Alves, D. C. R. Espinosa

"The world production of crude steel in 2009 reached 1.2 billion tons. For each ton of steel produced, 150 kg of steelmaking slag and 20 kg of steelmaking dust are generated. These are wastes with considerable production and limited applications, therefore this work studied the recovery of these wastes into useful sub-products. The slag was used as raw material in the production of rock wool (a thermo-acoustic insulator) and the dust was inserted in the iron ore sintering process. Results showed that produced materials have exceptional proprieties, therefore the recovery of these wastes can contribute to decrease extraction of non-renewable resources, reduce the costs and impact of disposals, and aggregate value to the slag and dust.1. IntroductionSteel production using Eletric Arc Furnace (EAF) has grown over 119 million tones in the last years. In 2008 30.7% of all steel produced, was obtained through EAF. In United States of America (USA) the percentage of this process in the production of steel was about 58% in 2008, while in 2000 this percentage was only 47% [1]."

Jan 1, 2011

By Qing-Yun Huang, Xiao-Yi Zeng, Bing Xie, Hong-Yi Li, Jia-Rong Yan

"In order to utilize vanadium resource in vanadium-titanium magnetite ore efficiently, vanadium distribution ratio between hot metal and slag should be improved during BF process, meanwhile the precipitating of Ti(C,N) in slag must be minimized. Effects of temperature, Ti02 content in the slag and basicity on vanadium distribution between slag and hot metal were investigated by experiment and thermodynamic calculation. The results indicated that high temperature, low Ti02 content and high binary basicity of slag were beneficial to increase the vanadium distribution ratio. The effects of temperature and Ti02 content in slag on vanadium distribution were stronger than that of slag basicity.IntroductionVanadium is an important element that is widely used in industrial fields. Most of vanadium resource is hosted in vanadium bearing titanomagnetite [l]. Vanadium bearing titanomagnetite is thus one of the domainate raw materials to produce the vanadium products. In other words, the comprehensive utilization of vanadium bearing titanomagnetite is beneficial for vanadium resource utilization. Vanadium bearing titanomagnetite sources are abundant in Pan Xi of China [4]."

Jan 1, 2013

By P. Barrios

Over a period of one year, an in-depth investigation was carried out in a conventional copper refinery to understand the behaviour of silver in copper electrolysis. The increase in silver content in the cathodes increases almost linearly with the duration of electrolysis, and the silver content of the electrolyte between the electrodes shows similar behaviour. The silver content of the cathode deposited daily depends directly on the silver concentration of the electrolyte and this, in turn, is strongly influenced by its internal temperature. The average temperature between the electrodes rises from the first to the second and to the third crop, because of the increase in the distance between the electrodes and the heat generated by the passage of the current. The mechanism of dissolution of silver from the anode, and its passage to the cathode, are discussed. Following the change to the Isa system, it was proved that the results and conclusions are analogous. Based on these results, a reduction of more than 20% in silver losses in the cathodes was achieved.

Jan 1, 1999

By Donald I. Bleiwas

World primary nickel production in 1987 is projected to be 770,000 mt, slightly higher than that in 1986. Market economy country (MEC) production in 1987 is projected to be about 524,000 mt, an increase of almost 5 pct over 1986 production. Production cutbacks and closures at Japanese ferronickel plants in 1987 resulted primarily from the strong yen and higher energy prices. Cutbacks also caused reductions in ore production from Indonesia, New Caledonia, and the Philippines. Technical problems affected production, to varying degrees, in Botswana, Indonesia, and Yugoslavia. World primary nickel production for 1988 is projected to be 787,000 mt, of which 536,000 mt will be produced in MECs. Increased production is projected from Botswana, Canada, Cuba, and possibly Greece and Yugoslavia, while slight production decreases are projected for Indonesia, New Caledonia, the Philippines, and Zimbabwe. .. South African nickel production in 1988 could be severly curtailed by social strife. In the early 1990&apos;s Brazil and China could be major economic competitors to Western nickel producers.

Jan 1, 1988

By D. G. C. Robertson

The thermodynamics and kinetics of the reactions involved in fuming zinc from oxide slags using coal or coke were first studied in 1955 and have been the subject of many investigations since that time. The key reaction is ZnO(in slag) + CO = Zn(g) + CO2 This paper will review the some of the recent work, and will add new insights obtained in experiments carried out by the authors. In the first series of experiments it was shown that the reaction does not occur at an appreciable rate, as is expected from thennodynamic considerations. In the second series of experiments it was shown that zinc does not fume from the slag at a significant rate unless a reductant has been added. This again is in accord with thermodynamic considerations, but is in contradiction to some of the experimental results reported in the literature. A third series of experiments was carried out with excess coke being present, so that the rate of supply of reductant was not in any way controlling the rate. The kinetics of zinc oxide reaction were then found to be independent of the zinc oxide concentration, but increased with increasing basicity, and temperature. The presence of high concentrations of FeO in the slag also improves the kinetics. At low zinc oxide coneentrations iron oxide reduction occurred in parallel with zinc oxide reduction. We propose that (under the conditions of this work) the kinetics were controlled by a chemical step, namely the rate of desorption of an adsorbed CO2 species. This is the same mechanism as reported by Belton and co-workers for the kinetics of the reduction of FeO. This explains why the reduction of metal oxides in slags by hydrogen is often faster than by CO.

Jan 1, 2003

By Toshiaki Tsuru, Takeshi Ohgai, Hisaaki Fukushima, Shigeo Kobayashi, Tetsuya Akiyama

"Electrodeposition behavior of Zn-Cr alloys from the methanol baths was investigated. In the methanol baths of low Cr3+ concentration, Cr (III) compound was incorporated in the deposits and no lusfrous Zn-Cr alloys was deposited. However, Cr was existed as metallic state in the deposits obtained from the baths of higher Cr3+ concentration. With an increase in water content in the baths, the chemical state of Cr in the deposits changed from metallic to trivalent state. Under the condition that metallic Cr can be electrodeposited, Zn deposition was significantly polarized to the potential of Cr deposition.INTRODUCTIONAn attention has been paid to Zn-Cr alloy plated steel sheet because of its excellent properties for body panels of automobile and electrical appliances [1]-[4]. This plating process can be operated using the sulfate solutions containing Cr3+ ion [1] - [6].In decorative single Cr plating, on the other hand, many attempts have been made to electroplate Cr from trivalent electrolytes, which is motived by environmental deficiencies of the presently used hexavalent process [7]. [8]. However, it has been reported that in the aqueous solutions the behavior of the electroreduction of 0 3+ is atypical due to the complicated nature of the chemistry and electrochemistry of cr3+ species [9]-[11]. Even in Zn-Cr alloy plating, it is difficult to codeposit metallic Cr with Zn in simple sulfate electrolytes [l]-[4], [12]. Therefore, it can be expected that the electrodeposition behaviors of Zn-Cr alloys as well as Cr are significantly changed when the electrodeposition is conducted in non-aqueous plating solutions.In this study, the electrodeposition of Zn-Cr alloy was conducted from methanol solutions to clarify the electroreduction mechanism of Cr3·-Cr0 in the alloy deposition process."

Jan 1, 2000

By K. Fukushima, K. Baba, H. Kurokawa, M. Yamagiwa

"The Toyo smelter has expanded its anode production capacity from 126,500 to 239,000 t/year by introducing technical oxygen into blast air for flash and converter furnaces and improving smelting facilities. Significant efforts were made in the expansion not to increase the number of workers, which mean development of some automation systems for the copper converters and anode casting wheel. The efforts have resulted in the above-mentioned increase in productivity and a saving of production cost as well as a decrease in the number of workers for the anode casting operation.IntroductionThe Toyo smelter has been performing a highly stable and pollution free operation since its commencement in 1971 (1). Its distinctive features are the on-line control by process computer (2) and the high productivity without trouble. But owing to the so-called oil crisis in 1979, we were faced with a sharp increase in production cost. To decrease the production cost, some measures for saving of energy were planned and carried out, such as conversion from oil to coal in a flash furnace (3), the heat recovery from converter slag and the introduction of technical oxygen in blast air with the intention of energy saving as much as possible.The first increase in production capacity and some savings of production cost were attained in 1982 by the introduction of technical oxygen in blast air for the flash furnace without major modification of the furnace as shown in Table I. The capacity of an oxygen plant is 7,800 Nm3/H as 90% O2 . Part of oxygen from the plant is also supplied to tuyeres of copper converters through an oxygen holding tank with a volume of 830 m3 at 7 kg/cm2-G."

Jan 1, 1989

By Mingchun Lu, Zhijia Liu, Xueqi Zhang, Jianliang Zhang

"In order to solve the problem of shortage of scrap, especially high quality scrap, a new substitute for scrap or DRI has been developed. The decarbonization mechanism of granular pig iron has been analyzed and the technical process and decarbonized granular pig iron have been evaluated in this paper. The research result shows that this new process is superior to direct reduction process in product quality, construction investment, operation flexibility, production efficiency etc. Decarbonized granular pig iron (DGPI) not only can be used as conventional scrap but also can be charged into EAF as high purity .burden equivalent to heavy scrap:IntroductionIn the past years, with the universal application of continuos casting technique in China, the amount of scrap generated inside steelworks has been reducing continually. On the other hand, the EAF steel proportion is increasing and this gives to the obvious change in structure of steel product. At present, the requirement on both scrap quantity and scrap quality is being paid more and more attention. Because China is a country which is devoid of scrap and poor in resource (nature gas and high grade iron ore) for developing direct reduction iron (DRI) so that sponge iron can not be produced cosmically in China and has to be mainly imported. Instead of part of scrap, some cold pig iron in cold state has been charged into EAF in China. However the high carbon content in pig iron has limited its proportion in EAF metal burden. Because the price of pig iron is lower than that of imported DRI in China, the technique of granular pig iron decarboniztion is hopeful to become effective way to produce substitute for scrap or DRI."

Jan 1, 2000

By K. G. Wang, M. E. Glicksman, P. Crawford

"We formulate the mathematical solution to late-stage multi particle diffusion in finite systems. The transition from finite system behavior to that for an infinite system is established. Large-scale simulations are reported regarding the dynamics of phase coarsening. Even in the case of a small volume fraction (Vv = 10-4), the particle size distribution is broader than that for the well-known Lifshitz-Slyozov limit at zero volume fraction. We also report the first simulation studies of extremely low volume fraction, for which corresponding experiments, as well as other simulations, do not exist at present for comparison. However, in the case of moderate volume fractions (Vv = 0.1), the fiucutations in the volumetric growth rate of particles are extracted from our simulations. These simulations provide additional insight into the statistical nature of diffusion interactions, including multiparticle stochastics during microstructural evolution.IntroductionPredicting microstructure evolution in alloys remains one of the cornerstones of materials science. Phase coarsening is a common process in microstrucural evolution that leads to a decrease in the excess total interfacial energy of the system. The system typically consists of separate and identifiable units, or domains, such as second-phase particles distributed in a matrix. During phase coarsening, larger particles grow at the expense of small particles. Over time, this ""competition"" results in an increase in the average size of the particle population, and in a concomitant decrease in the number of particles.Particle size and microstructure of many cast alloys depend on similar coarsening processes. Indeed, properties of these materials, such as strength, toughness, ductility, and electrical conductivity, depend on the material's average particle size and particle size distribution (PSD). Understanding and controlling microstructures in two-phase systems are clearly of widespread technological importance."

Jan 1, 2001

By Thomas Brynjulfsen, Merete Tangstad

"Manganese ore fines, generated during mining and transportation, can not be added to the submerged arc furnace directly as they will prevent even gas flow through the burden. Low gas permeability in the burden will lower the degree of pre-reduction of ore and subsequently increase the carbon and energy consumption of the process. In order to utilize manganese ore fines in the furnace they are agglomerated into sinter, pellet or briquettes. The agglomeration process will however change the reduction properties of the ore. In this work the melting and reduction properties of sinter has been investigated.The melting temperature and melting mechanisms has been studied. The mineralogy of the raw ores and agglomerated has been found using XRD, and the composition established using EPMA(WDS). The effect of adding fluxes such as dolomite and quartz has also been investigated.IntroductionManganese metal is produced in a submerged electric arc furnace or in blast furnaces. The reduction of manganese oxide in blast furnace has in the recent years become more unusual due to the high consumption of reducing carbon material[5]. Manganese metal for alloying in steel usually contains silicon and iron, and are therefore called ferro manganese and silicomanganese.During mining, transportation and handling the manganese ore is broken up into different size fractions. The larger lump are used directly in the electric arc furnace, but the finer materials can not be added without treatment. The fine ore can disrupt the flow of CO and CO2 gas through the burden, subsequently reducing the degree of pre-reduction. The fine fractions must therefore be agglomerated into larger lumps, in order to promote gas flow. This can be achieved through a number of different processes. The agglomerate used in this work has been sintered, which means that is has been partly molten and reduced, in order to create bigger lumps."

Jan 1, 2012

By C. M. Acuna

Scarcity of high grade copper low impurity content ores is a reality and processing of low grade dirty concentrates is a need. In spite of this fact, innovative strategies have to be looked at to comply with day to day more stringent environmental regulations. From this perspective the production of matte grades over 70% in copper presents several merits, but it must be contrasted with the fractional distribution of impurities reporting to the condensed phases. Converting of white metal high in arsenic content results in moderate fraction of arsenic to gas, but high deportment to blister. Therefore, production of anode copper, as required by the electrolytic refinery, may result in several operational difficulties. Furthermore, by recycling the flue dust and slag produced in the smelting-fire refining cycle, the arsenic content in the feed to smelting increases and so does in the resulting anode copper. The Teniente Converter, as a smelting unity, has probed suitable for production of high matte grade near white metal composition but regarding distribution behaviour of impurities there is lack of reliable data, specially when processing concentrates over 1% in arsenic content. In the new scenario, i.e. low grade copper high arsenic content concentrates, to fully asses the merits of this technology the effect of matte grade, secondary materials recycling and arsenic in feed upon the distribution coefficient of arsenic between slag and matte, mainly, must be evaluated both from a theoretical approach and by use of industrial data. Based on available data correlations of distribution coefficient, matte grade and matte/slag ratios with arsenic in feed and copper content in slag are worked out. Based on these results suggestions as to matte grades facilitating to deal more efficiently with the handling of smelting byproducts are proposed.

Jan 1, 2006

By S. V. Subramanian

The tool material and the machine design for high speed machining are well advanced over the last decade but the steel design has lagged behind. The paper examines the design of steel in order to control the sliding tribology for high speed machining under dry machining conditions. In high speed machining of steel, accelerated chemical wear of the tool occurs once atomic contact is established at the tool-chip interface, resulting in poor tool life even with high performance tools such as cubic boron nitride. Recent research has confirmed the occurrence of nanocrystalline grains in the interfacial layer of the chip at the tool-chip contact. The volume percentage of grain boundary is increased significantly (10 to 30%) as the nanocrystalline grain size is decreased well below 30 nm. The solubility of tool material into the nanocrystalline grain boundary is two or three orders of magnitude greater than in the crystal lattice. Further the kinetics of diffusion in the grain boundary is seven or eight orders of magnitude greater than in the crystal lattice. Enhanced nanocrystalline grain boundary diffusion occurring in the interfacial layer at the tool-chip contact causes the accelerated chemical wear. Significant improvement in tool life could be achieved by engineering glassy oxide inclusions in steel, designed to self-lubricate the tool-chip interface in-situ at higher cutting speeds. Thus the control of sliding tribological condition at the tool-chip interface is key to suppress nanocrystalline layer formation at the tool-chip contact and hence prevent accelerated chemical tool wear. Sulfide inclusions are designed essentially to promote chip fracture. In addition, sulfide inclusions are designed to act as a diffusion barrier at the tool-chip interface. The application of inclusion engineering concepts to enhance the tool life in high speed machining will be demonstrated with a suitable case history.

Jan 1, 2006