Search Documents

By Gordon Holcomb, George R. St. Pierre, Robert A. Rapp

Carbon/Carbon composites offer promise as high-temperature structural materials. A primary limitation on their application is the need to provide protection against oxidation in hot oxidizing environments. Silicon carbide conversion coatings have been shown to provide extended protection at temperatures of 1600°C. SiC coated C/C components have been used in several aerospace applications. In the present paper, the preparation of carbon fibers and their treatment during subsequent processing into coated components are discussed with particular emphasis on the processing variables that can result in improved oxidation resistance. In particular, the influence of substrate inhibitors and selective sealants for cracks in coated C/C components are analysed.

Jan 1, 1988

By Qinghai Pang

"With the increasing proportion of bituminous coal in blend coal, the safety of blend coal during pulverization and transportation is gradually being paid more and more attention. Therefore, the explosivity of bituminous pulverized coal (PC) with different volatile content from 25 to 38% was studied by measuring the combustion flame length after its injection into a glass pipe with the heat source installed in the center. The results indicated that high volatile content bituminous PC is apt to have higher explosivity. By blending different bituminous PC with 10% anthracite, the explosivity of bituminous PC showed a positive correlation with the proportion –OH radical. However, different bituminous PC seemed to have the same explosivity when the addition of anthracite increased to 20%. With the further increasing proportion of anthracite to 30%, the explosivity of bituminous PC with high –OH proportion became negligible while a weak explosivity of high –CH3 proportion bituminous PC still remained.IntroductionWith the increasing iron ore prices and decreasing steel prices, it has become critical for iron and steel enterprises to control the cost in ironmaking and steelmaking process. Blast furnaces (BF) are the main consumer in ironmaking process, which occupies 70% fuel consumption of total steelmaking process [1]. In this circumstance, any means necessary is taken by BF operators to lower the cost of iron in production. Coke and iron ore are the main expense in this process, who takes up a very high proportion in total cost. Pulverized coal injection (PCI) is the most efficient way to reduce coke ratio, which replace coke with relatively cheaper PC.At present, most of BF is injected with blend coal in the consideration of decent combustion property and quantity of heat. Simultaneously, bituminite and anthracite blending is an effective method to obtain blend coals with required composition and performance, such as volatile and ash content, etc. Nevertheless, a very huge gap was found between the price of bituminous coal and anthracite in some regions of China, in which the price of bituminite can be just 70% of the price of anthracite. Thus, iron enterprises in these regions attempt to possibly amplify the proportion of bituminite in blend coal. Increasing proportion of bituminite results in higher volatile content in blend coal, by which the safety of blend coal during pulverization or transportation was deteriorated.Relatively, coals with higher volatile content usually possess stronger explosivity, which means that volatile and explosivity may related to some extent. However, the relationship between volatile and explosivity is not of certainty for some PC with high volatile content around 40% was found to be inexplosive in comparison to the coals with lower volatile content. With the increasing proportion of bituminous coal in blend coal, investigations on the factors of PC explosivity have become more and more important. Therefore, bituminous coals with different volatile content were selected. The explosivity of blend coal and its relationship between volatile content and functionality was investigated in this research."

Jan 1, 2014

By Anand Kumar, Pradeep kumar Jha, Suman Kant, Pradeep Kumar

"It has been a major challenge to reduce the intermixed grade formation during ladle change-over operation in continuous casting process of tundish steelmaking. The F-curve generated by step input of the tracer (new grade steel) tells about the intermixed grade amount for different grade specifications. Use of flow modifiers is beneficial in reducing the intermixed grade because of the change in slope (in different time zones) and position of the F-curve due to their placement at tundish bottom. Present study aims at investigating the role of dam placed before the outlet in a multi-strand tundish with reference to the slope behavior of F-curve in different time zones during the teeming operation plays an important role in determining the intermixed amount.Introduction In Continuous casting process, the old grade steel remaining in the tundish (reservoir between ladle and mould) from the old ladle gets mixed with new grade steel from new ladle and leads to intermixed grade which is considered to be of inferior quality. Although formation of intermixed grade is inevitable with the sequential method of casting, its amount can be controlled by changing the flow behavior of steel inside the steel. Intermixing in a slab caster tundish was simulated using 3-D numerical model based on k-å turbulence equation and compared their result with that of water model experiment Yeh and Hwang [1]. Huang and Thomas [2] reported that quantity of residual fluid in tundish affects the composition distribution in the transitional slab and thus the intermixed length. Huang and Thomas [3] developed three sub models to predict mixing in tundish, liquid core of strand and solidification. Thomas [4] developed a one dimensional model to simulate the final composition distributions in slab caster of continuous casting and investigated the effect of process variables on the intermixing. Alizadeh mehdi et al., [5] simulated of the intermixing phenomenon for slab casting for three different sub models. Goldschmidt et al. [6] developed a numerical model that predicted the location of the intermixed steel in a four line round caster. Lan and Khodadadi [7] studied for the transient fluid flow of liquid steel, heat transfer and solidification during the flying tundish change process. Cho and Kim [8] developed a mixing model to predict the outlet concentration of the tundish during grade transition. Most of the work reported in the literature has dealt with intermixing in slab caster tundish. Billet caster units are more often being used by steel industries due to growing demand of billets. The multiple outlets lead to varying degree of intermixing with time owing to their different distance (location) from the inlet. Use of flow modifier to minimize the intermixed amount, however has also not been discussed in detail so far. Further no work has been reported regarding effect of slope of F-curves obtained through different outlets on intermixing. Hence keeping these objectives in mind attempt has been made by authors to analyze the slope of Fcurves after dividing them into three different time zones and the effect of these time zones on intermixing."

Jan 1, 2012

By Takeshi Nagano

Copper pyrometallurgy in Japan has experienced quite fundamental changes in last fifteen years. The severe environmental restriction coupled with increase of energy costs accelerated the development work of the new continuous process in Mitsubishi Metal Corporation. After several years of pilot plant test work the commercial plant was put into operation at Naoshima Smelter in 1974, the design capacity of which was 4,000 tonnes of copper per month. Many modifications and improvements have been incorporated into the process and 7,200 tonnes per month of copper production was achieved in 1983, proving that continuous process was much more economical than conventional process. It is now possible to design and operate the continuous process in wide range of capacity. This paper will review the process and describe the progress of the process in these 10 years. 311

Jan 1, 1985

By K. Tozwa

The electrical conductivity of electrolytes for copper electrorefining and electrowinning processes has been reported by many researchers since 1911. The experimental results show that the conductivity increases with an increase in sulfuric acid concentration and decreascs with an increase in copper concentration. In pure copper sulfate solution, however, the conductivity increases with an increase in the copper concentration. After confirming the conductivity of pure and acidified copper sulfate solutions experimentally, the concentrations of hydrogen ion and free (not hydrated) water in the electrolytes were estimated and it was found that the relation between the conductivity of acidified copper sulfate electrolytes and the products of concentration of hydrogen ion and free water is linear. Accordingly, the conductivity of acidified copper sulfate electrolytes increases with an increase in sulfuric acid concentration and decreases with an increase in copper concentration.

Jan 1, 2003

By Clyde S. Brooks

This paper undertakes to assess what opportunities exist for the economical recovery of non-ferrous metals from spent catalysts. The most promising recovery appears to lie with metals such as Co, Mo, Ni, W, heterogeneous catalysts used on a large scale in petroleum processing. Nickel is a metal with diverse applications on a large scale notably in hydrocarbon steam reforming and in vegetable oil hydrogenation. In addition, several of the precious metals, notably Pt, Pd, and Rh, find extensive use in fossil fuel processing and in automotive and power plant flue gas control. The hydrometallurgical and pyrometallurgical alternatives for processing are identified and discussed, especially with citations to illustrate reduction to commercial practice. Promising directions for adaptation of appropriate, economic separation technologies for recovery of non-ferrous catalytic metals generated in significant amounts for the secondary metal markets are identified. Recycling

Jan 1, 2000

By L. Dornelles, M. H. Prediger, R. de C. de S. Schneider, D. A. R. Lopez

In this work it was evaluated the environmental impact of sunflower plantation for biodiesel production. It was considered, for life cycle analysis (LCA) of sunflower in familiar agriculture in the South of Brazil, data collected in 23 experimental farmings with sowing in the period from August to November (2006 -2007). The LCA has considered the plantation conditions, energetic efficiency, man power, diesel volume, type of machines, fertilizers and pesticides used. From the analysis carried through it was evidenced that the sunflower produced in small scale does not need the use of tractors to have an excellent productivity and low impact. Therefore, the sunflower can be cultivated, with the necessary cares, in periods that do not compromise the man power for other cultures and the sunflower is an alternative so that the familiar property can produce biodiesel.

Jan 1, 2008

By A. H. -J. Siegmund

Since the last survey of lead smelters in 1987, the lead industry has experienced many changes. Technological innovations, in combination with a dramatic shift in the market structure as well as more stringent government regulations, caused major upheavals in many different areas. Therefore, a new survey was performed to review the progress in the technology of lead recovery over the least decade. The newly conducted survey reflects all current phases of the world's primary lead production, from charge preparation to refined metal shipment. It was prepared by sending questionnaires to individual companies, and the detailed statistical data of this survey are presented. In considering the data developed from the survey, it should be recognized that the primary lead industry is at a crossroad where novel technologies will gradually substitute the sinter machine - blast furnace operation in the new millennium.

Jan 1, 2000

By B. C. Blakey

The economic feasibility of the sulphuric acid pressure leaching route for the extraction of nickel and cobalt values from limonitic ores is highly dependent upon the behavior of aqueous aluminium. This is primarily due to its precipitation as hydronium alunite ((H30)A13(S04)2(OH)6), which is one of the major scale-forming compounds found in autoclaves used for pressure leaching. As a result of renewed interest in the pressure leaching process, an investigation of the aqueous-solid eqilibria in the aluminium-sulphate-water system under acidic (< pH l), high temperature (230 to 270°C) conditions has been conducted. Pure hydronium alunite was synthesized in an autoclave by leaching boehmite (A100H) at elevated temperatures in sulphuric acid solutions initially 0.25 to 0.75 m H2S04 in concentration. Spontaneous, in situ precipitation of hydronium alunite followed. A high temperature solution speciation model was used for the analysis of the resulting solubility data in order to calculate equilibrium constants for the precipitation reaction.

Jan 1, 1994

By J. T. I. Poijärvi

The smelter off-gas cleaning and the weak acid treatment at Outokumpu Harjavalta Metals Oy are presented and described in this paper. The smelter consists of the copper and nickel smelters and the acid plant of three separate acid plants two of which are double contact and one single plant and of one liquid sulphur dioxide plant. The preliminary cooling and flue dust separation of the smelter off....,gases from the copper ?and nickel flash smelting furnaces and converters? in the waste heat boilers and in the hot electrostatic precipitators are described. The final cooling and cleaning of the gases in the scrubbers at the sulphuric acid plant and the treatment of the weak acid in the vacuum and in the submerged combustion evaporators for the removal of impurities are presented as well as the treatment of the condensates from the evaporators. The attention is paid to the generation of sulphur trioxide in the smelter off-gas.and to the treatment of that in the weak acid bleed-off and to the utilization of the treated acid.

Jan 1, 1992

By R. M. Cunningham

Asarco operates one of the largest individual copper electrolytic refineries in the world at Amarillo, Texas. The feed for this refinery is a mixture of anodes produced at Asarco smelters and copper purchased t?om a number of primary and secondary sources. The variation in feed makes it imperative that the refinery practices state-of-the-art quality control to minimize the effects&apos;of unwanted impurities in the electrolytic refining process. In late 1993, a plant designed to sigru6cantly reduce the antimony and bismuth levels in the electrolyte was commissioned. The purification plant uses ion exchange technology in conjunction with a novel strippiing system developed by Zeneca Specialties (U.K.). The strippiing system permits the recycling of the eluant and thus avoids the extremely high costs of stripping with conventional reagents. In addition, the environmental impact of treating the eluant for recovery of antimony and bismuth is minimized. This paper outlines the development of the technology and, in particular, describes the operational practices and improvements at Amarillo since the commissioning of the plant.

Jan 1, 1997

By M. Misra, J. Nanor

The precipitation and removal of arsenic from process waters can be accomplished with addition of lanthanum chloride alone or in conjunction with ferric sulfate. The long term stability of these corresponding precipitated compounds is critical from the disposal stand-point. In this paper the characterization of ferric, lanthanum and lanthanum-ferric arsenate compounds formed at room temperature in acidic and alkaline pH is presented. The characterization techniques used included zeta potential, XRD and SEM. Zeta potential measurements of ferric and lanthanum hydroxides in the presence of arsenate indicate that oxyanions of arsenate are chemically adsorbed onto the positively charged surfaces of these hydroxides. In alkaline pH there is desorption of arsenate species from the ferric hydroxide surface, hence the product is thought to be unstable. On the contrary, lanthanum arsenate is stable in alkaline pH. XRD patterns show that the ferric arsenate formed in acidic and alkaline pH is amorphous, whereas lanthanum arsenate and lanthanum-ferric arsenate formed in acidic and alkaline pH are crystalline.

Jan 1, 1999

By Peter Kettle

This paper describes the performance of the copper industry over a period of some two decades and examines the theme that improvements in operating efficiency have not been matched by improved returns on capital. The financial performance of the copper industry is analysed using CRU&apos;s MICA database. Regression analysis indicates a two percentage point increase in operating margins but no increase in returns on capital. The gain in operating efficiency appears to have been mainly achieved in the mid 1980s. The investment boom of recent years has resulted in a rapid increase in the industry&apos;s level of debt and gearing ratio (now some 47%). Data on 44 copper mine projects is used to show the linear relationship between scale and capital costs. Typically new capacity costs some US$5,000 /tpy. The relationship between cash costs and capital intensity of projects is also plotted. The greater attention now being focused on efficient use of capital means that capital intensity rankings will become increasingly important in determining which projects go ahead.

Jan 1, 1999

By Rainer Köster, Tobias Wagner, Markus Delay, Fritz Hartmann Frimmel, Wolfgang Ferstl, Wolfgang Höll

"The mobilization of contaminants from industrial residues like ashes from municipal solid waste incinerators in case of leaching is investigated world wide. In classical leach tests only soluble species are considered. In addition the geochemical behaviour of residues has to be completed by assessing the mobilization via colloidal particles. This transport is well known from natural aquatic systems. Quantification of aquatic colloids is associated with considerable difficulties, because they are often found in low concentrations and in a size distribution where small particles with diameters below 0.1 µm predominate. In the past years, the Laser-induced Breakdown Detection (LIBD) has been developed as a novel sensitive method for quantifying colloids. Column leaching experiments with directly coupled LIBD were used to quantify the release of heavy metals and colloids out of bottom ashes. Some typical colloid bound heavy metal concentrations in the leachate are in some cases exceeding the limits defined by German authorities. The LIBD with a flow-through cell allowed to assign absolute values to colloid size and concentration."

Jan 1, 2008

By Yuhsuke Mizukami

Crude high Cr containing steel such as tool steel, heat-resistant steel or stainless steel is produced by dissolution of high carbon ferro-chromium into molten crude steel. In the refining process, decarburization is performed at the first stage, and deoxidation is followed in the next stage. Therefore, the equilibrium relation between dissolved Cr and 0 in molten Fe-Cr alloy after decarburization is very important when yield of deoxidizer is considered for the ovemll control and optimization of the process. It is well known that the yield of deoxidizer does strongly depend on the kinds of refractories of furnace in the secondary refining process. In the present work, the equilibrium relation between dissolved Cr and O in molten Fe-Cr alloy has been measured in a Cr2O3, MgO or Al2O3 crucible at steelmaking temperature. O contents at given Fe-Cr components have been lower in order of Cr2O3, Al2O3 and MgO crucible. The present results have been discussed based on the activities of the constituents in pure solid Cr2O3, and FeO-Cr2O3, MgO Cr2O3 and (AI,Cr)2O3 solid solutions.

Jan 1, 2003

By Muhamad Firdaus

There is a growing interest in Magnetoelectric (ME) materials in view of both fundamental understanding and novel desirable applications. The application potential for multiferroic materials with the possibility of reversing the magnetization by applying an electric field (or vice versa) is quite promising especially in data storage application. The rare earth ortho-ferrites (REFeO3), such as NdFeO3, have been studied extensively in recent study in the context of discovery of magneto-electric (ME)/multiferroic nature materials. In this paper a potential high temperature recovery of rare earth elements in the form of REFeO3 from waste permanent magnets using direct oxidation in air was investigated. It was found that REFeO3 (NdFeO3) phase can be separated from the other oxide phases by thermal treatment of NdFeB magnet waste at 1100 °C in air atmosphere. The REFeO3 also found to have different physical characteristic (density) from the other layers and can be separated physically. This paper will include a proposed flowsheet to recover Nd as NdFeO3 through powder separation. The technique can be beneficial and favourable for RE recycling and recovery from waste permanent magnets.

By John Hollow

The Fort Knox Mine is an open-pit operation, located in Alaska, which started commercial production in March 1997. A conventional Mill processes 38,000 tpd of a low grade (1.0 g/t Au) free milling gold ore with a low sulphide component (below 1%). Gold production (11% from gravity and 89% from cyanidation) exceeds 400,000 ounces per year. Short retention time (20h), low temperature (7oC) and low grade make high leaching kinetics critical for the performance of the process. In April 2001, the treatment of True North ore, which represented 14.4% of the mill throughput and contained more sulphide in the form of pyrite, arsenopyrite and stibnite, resulted in a substantial drop in the average gold extraction from 87% to 72.6%. Laboratory investigations indicated that the addition of lead nitrate increased gold extraction to 91.7%. Further investigations were initiated to determine the leaching parameters and the nature of the problem. Subsequently, a lead nitrate addition scheme was implemented at the Fort Knox Mill that resulted in 2002 gold production being in excess of 31,000 ounces higher than that estimated for the non-lead nitrate reagent scheme. This paper presents the results of laboratory investigations and modifications in plant operating practices.

Jan 1, 2003

By Nobuhiro Oguma, Yuji Mizuta, Hideya Sato, Shigehiko Iwahori

"Recyclable materials containing copper and precious metals have been treated at the Mitsubishi Process in Naoshima. In 2003, a new incinerating and melting plant (pre-treatment plant) for waste materials, such as shredder residue of automobile and scrapped appliance, was constructed. All of produced slag/metal mixture is treated at the Mitsubishi Process, and which results in the significant increase of recyclable materials treatment. The combination of two processes has realized a highly efficient and environmentally friendly system for recycling valuable metals in the waste which used to be sent to a landfill. Naoshima continues to make efforts to achieve the highly efficient operations of the two processes, and plans to increase the treatment of recyclable materials further. This paper summarizes the recent operations and the various improvements implemented in the pre-treatment plant.IntroductionRecyclable materials containing valuable metals such as copper and precious metals have been treated at the Mitsubishi Continuous Copper Smelting and Converting Process (Mitsubishi Process) since the start-up in 1991. In the early stages, recyclable materials consisting mainly of metal scrap were charged into the process and the treatment had been increased steadily. In order to promote the recycling business, treatment of various kinds of materials including printed circuit boards was started. However, the treatment hit the ceiling due to a limitation of furnace boiler capacity, since they contained large amounts of combustible materials. In addition, severe corrosion of boiler tubes was caused by halogen contained in recyclable materials."

Jan 1, 2012

By Hideki Minoura

"Two novel electrochemical techniques for the preparation of highly crystallized CdS film have been presented. One is cathodization of a conductive substrate in an acidic chemical bath containing cadmium salt and thioacetamide, where electroreduction of proton at small current densities induces a growth of highly crystallized CdS thin films, whose growth is not disturbed by the reactions in the solution phase. The other technique is electoreduction of aqueous Cd2+— SCN complex. An advantage of this technique lies in no formation of solid particles in the bulk, of the bath.IntroductionIn recent years much attention has been paid to materials preparation by solution processing because of its advantages in lowering the cost as well as the stress to the environment, as compared to the conventional gas phase techniques which unavoidably require high temperature and/or vacuum. We have been trying to explore novel techniques for preparing functionalized compound semiconductors by aqueous solution process. Semiconductors which we have been mainly focusing on are CdS and ZnO, which are important semiconductors finding applications in various devices. In the present paper, some of the techniques that we have recently established for the preparation of highly crystallized CdS will be presented.Methods of the CdS film processing in solution phase (wet process), which have been reported so far can be divided into two major groups; one is chemical bath deposition (CBD) in alkaline solution containing Cd2+ and thiourea 1)4) and the other is electrodeposition (ED) in acidic solution containing Cd2+ and thiosulfate ions - 5)-8) or organic solutions containing dissolved sulfur 9)-11)."

Jan 1, 2000

By M. Kobashi, T. Choh, N. Kanetake

"A new processing route, which enables the cost-effective and energy- saving fabrication of metal matrix composites, have been proposed. The pressureless infiltration of the reactive powder blend with molten aluminum was investigated in this work. The molten aluminum infiltrated into the [Ti + C] powder blend spontaneously, whereas the spontaneous infiltration into the TIC powder phase did not occur under the same experimental condition. The processing time was shortened and· the processing temperature was .lowered by adding the aluminum powder in the [Ti + C] powder. The differential thermal analysis revealed that the aluminum powder in the powder blend melted at 933K and then ignited the reaction between titanium and ·carbon. However there was an .optimum additional amount of aluminum in the powder blend. The TiC formed in situ had three-dimensionally continuous morphologyIntroductionThe squeeze casting process has been used as one of the processing routes for aluminum matrix composites. [1, 2]. Non-reactive metal-ceramic systems have been, generally, used in this technique in order to prevent the degradation of the ceramic phase. Materials obtained by this process basically consist of a continuous metal matrix and discontinuously dispersed ceramic particles. Reactive systems have begun to be introduced into the infiltration process· recently [3A]. Since the ceramics are synthesized in-situ, this process can provide a continuous ceramic matrix [5]. This is one of the outstanding features of this technique in that a bulk ceramic-can be synthesized at relatively lower temperatures in a short time. Another advantage is that the highly reactive combination of a ceramic with a molten metal is in many cases wettable [6], which enables a spontaneous infiltration."

Jan 1, 2000