Search Documents

By María Cristina Ruiz

In the processing of copper concentrates by the conventional smelting-converting technology, complying with the increasingly severity of environmental legislation in some countries has become difficult, mainly due to severe fugitive emissions of gases produced during the batch PS (Peirce-Smith) converting step. In this work, the results of an investigation on the pressure leaching with sulfuric acid and oxygen of white metal (produced in a Teniente Converter reactor) are discussed. The study was carried out at laboratory scale and the main variables studied were temperature, concentration of sulfuric acid and partial pressure of oxygen. The experimental results indicated that most of the sulfur in the white metal was oxidized to sulfate in the whole range of temperature studied (105ºC to 150 ºC). The concentration of sulfuric acid over 0.05 M, and oxygen partial pressure over 6 atm had little effect on the dissolution of copper from the white metal. On the other hand, temperature had the most significant effect on copper dissolution; below 130 ºC copper dissolution was incomplete after 5 hours of leaching while at 150 ºC the dissolution was complete in 90 minutes and 10 atm of partial pressure of oxygen

Jan 1, 2006

By V. A. Bryukvin

It has been found that by superimposing symmetric alternating current over the process, the rate of nickel and cobalt leaching from metallized products with copper sulfate solutions increases by a factor of 1.5 to 2.0 and the apparent activation energy of the process investigated is reduced from 12 down to 6.6 kcal/mole. It appears especially attractive to use alternating current for anodic dissolution (oxidation) of metallic scrap of refractory metals and their alloys in ammonia electrolytes permits production of high-grade commercial products in the form of respective ammonium salts using a short and virtually reagent-free process flowsheet. Similar approaches can be applied also for electrochemical processing of nickel and copper scrap in sulfuric acid media with subsequent recovery of pure sulfate salts or electrolytic processing. Electrochemical technology for recycling of tungsten-cobalt (WC 15) and tungsten-rhenium (WR 20) alloys has been also investigated. In the former case, anodic oxidation of carbide alloy was carried out in nitric acid electrolyte with production of pure tungstic acid. The research conducted has indicated that the physicochemical effect of alternating current results in a lower activation energy of electrode reactions due to changes in the mechanisms of the electrode reactions themselves.

Jan 1, 2006

By Akira Yazawa

The composition of ferrous calcium silicate slag is located on the tie line between FeOx and calcium silicates in ternary FeOx-SiO2-CaO system. This slag has never been used as copper smelting slag because of high sulfidic copper solubility. However, when the dissolved copper in slag is just oxidic, as in direct white metal production or in converting process, this slag is quite attractive and can be regarded as the third copper smelting slag after fayalite and calcium ferrite slags. Based on the authors' studies on phase separation thermodynamics and laboratory experiments, it was clarified that the oxidic copper loss in this ferrous calcium silicate slag become the minimum not only %Cu in slag but also the total copper loss when the amount of slag is taken into account. It has been proven that calcium ferrite slag is suitable for continuous converting where the dissolved copper is oxidic, but there exist some drawbacks such as limited solubility of silica, low lead removability and too high fluidity. To overcome these difficulties accompanying traditional slags, ferrous calcium silicate slag is the hopeful alternative. In view of the general trends of modem copper smelting processes, the interesting features of this new slag system are discussed.

Jan 1, 1999

By William Brinkman, Mark Jolly, Nasim Soleimanian, Karl Dearn, Oliver Brinkman

"Glass manufacturing is a heat intensive process. There is a direct correlation between the batch distribution techniques and the furnace energy consumption, productivity, and quality of the glass manufactured. All four major segments (float, container, fibre, and specialty glasses) would benefit from using an optimised batch distribution technique where possible. Oscillating batch chargers (OBC) have been in use since the early 70s, despite their superior batch shape, coverage, and in turn positive effects on the energy consumption and productivity of the furnace they are almost exclusively used in container glass manufacturing. The OBC’s main difference compared with other charging methods is its ability to directly influence the batch initial velocity. This paper reports on results achieved in CFD models (GFM) used to study effect of the machine on the overall energy consumption in the doghouse and the melt space.IntroductionGlass manufacturing can be divided to four major segments float glass, container glass, fiberglass, and specialty glasses. The financial cost of manufacture, its impact on the environment, lack of standardisation and mounting pressure imposed by the authorities for reduction in emissions means that the industry and its suppliers are utilising CFD modelling in order to tackle these challenges. The need for high temperature to create and maintain the viscous flow, homogenisation of the glass melt, and maintenance of the process to allow continuous output of glass of the right quality are the contributors to the energy intensive activities that are involved in continuous glass manufacturing. This in turn has resulted in design of large container glass furnaces which have high energy consumption, low specific performance, and high CO2 emissions where the most efficient furnaces in the container glass sector have a specific primary energy consumption of 3.8 GJ /tonne of glass at a level of 50% cullet in the batch making even very small improvements in efficiency by operation optimisation a value adding activity [1-14].The theoretical calculated energy required to melt glass is 2 to 3 times less than the energy actually used to melt glass as a result of glass melt passing a zone 5 to 8 times before leaving the tank.[8]. This causes contamination as the result of mixing between the completely molten glass free from bubbles returning to the batch area where there is freshly molten non-homogeneous glass, still containing very large numbers of bubbles and un-molten batch. At high temperature some components are dissolved rather than melted. Given that an un-molten batch is a good thermal insulator, it can be transported a long way into the furnace, increasing the need for homogenization which also increases the glass residence time of glass melt. This is why large unbroken strings of batch should be avoided, as should an overall blanket without gaps."

Jan 1, 2014

By Bora Derin, Onuralp Yucel, M. Seref Sonmez, Murat Alkan

"Latest stage in the production of boron carbide by metallothermic methods using magnesium was the leaching process. Boron carbide particles obtained by self-propagating high temperature synthesis contained several impurities such as magnesium oxide and magnesium borates after the metallothermic reactions. Removal of such contaminates by hydrometallurgical methods required to produce high purity boron carbide. Leaching by concentrated hydrochloric acid solutions resulted in the production of pure boron carbide together with high magnesium and boron containing solutions. Removal of such ions from the spent liquor was the necessity to have dischargeable solution. In this study, precipitation of magnesium and boron compounds from relevant chloride containing spent liquors and the production of saleable products was aimed. The effects of chemical reagents, pH of the solution on the precipitation efficiency of magnesium and boron compounds were investigated in the study. Chemical analysis and the characterisationof solid phases by using x-ray diffraction analysis were the latest stage.Introduction A variety of advanced ceramics, inter-metallic, organic and inorganic compounds, oxygen free single crystals, and polymers can be synthesized by using different SHS techniques [1, 2, 3]. In the SHS process, after initiation, reaction becomes self-sustaining and propagates in the reactant mixture. A high amount of heat which is generated during the process accelerates the reaction rate and thus it makes the process highly productive and economically feasible for different production scales. After the SHS process obtained powder mixture needs to reacted with acidic solutions to purify the product. In this case B2O3 was reacted together with C and Mg to synthesis fine B4C powder resulted in the production of MgO as well according to the Eq. 1 and then MgO was removed from the mixture by leaching with the concentrated HCl solution as shown in Eq. 2, respectively [4, 5]."

Jan 1, 2008

By José Sancho, Julia Ayala, Purificación García, Begoña Fernández

"A study is carried out to see the adequacy of using flying ashes coming out from a Power Station to eliminate the copper present in waste cyanide waters that are generated in gold mines.Tests were carried out to see how effective the use of ashes taken from two Power Stations could become. Later, the tests are made using ashes coming from Narcea Power Station as this station is near the mine under study.The work is centred on looking for an economically adequate solution to close the waste decanting ponds of the mine. After several tests, a solution is reached through filtration in static layers.IntroductionThe use of coal to adsorb some water-soluble substances has been widely studied [1,2,3,4,] both in the treatment of drinking waters and in determined stages of selective detachment of cyanide gold complexes in cyanide lixiviation processes [5]. Flying ashes sent to the atmosphere by Power Stations as a sub-product of the combustion of this combustible are generally made of more of a 70 % of a vitreous aluminosilicated material and of an active residual material which may be changeable making them potentially useable as adsorbents. Nevertheless, the properties of each kind of ashes depend on the characteristics of the Power Station, of the combustibles being used, of the combustion system, etc.The aim of this work is to demonstrate the adequacy of flying ashes to eliminate the copper present in cyanide waters coming from gold mines either by adsorption or precipitation of the metal. For this study, tests are carried out with Asturian ashes which have a low quantity of lime. The results obtained in the tests demonstrate the effectivity of the method used. To be absolutely concrete, the work is carried out to establish the use of these ashes in the closing of Asturian installations of cyanide lixiviation"

Jan 1, 2008

By Motoyasu Sato

Highly pure pig irons were produced in a multimode microwave reactor from powdered iron ores with carbon as a reducing agent in the nitrogen atmosphere. The grains in compacted powder absorb microwave energy selectively. Microwave-matter interaction creates thermal non-equilibrium state microscopically and enhances chemical reactions and the phase mixing at the grain boundaries very rapidly. The visible light spectroscopic techniques was used to monitor the progress of the reactions. Up to 650°C, the heated powders radiate the continuous spectrum of blackbody emission. The small non-equilibrium hot spots rise, move and finally burst in to brighter light emitting from all over the surface at 650°C. CN molecules and Fe (I) atoms were identified in the recorded spectrum. These bursts are similar to the ?ignition propagation? normally observed in chemical reactions. The line spectra originated from CO molecules have not been detected yet. The solid-solid reaction could be expected between the iron oxides and carbon to produce CO2 directly. A loss in the sample weight was accelerated during the excess-emission. These are the clear evidence that microwaves cause thermally non-equilibrium state and accelerate reduction process. The reduction of iron ore is completed at 1380°C and relatively very pure pig iron was produced. It should be noted that the impurity level of Mg, S, Si, P and Ti is only 5-10% of what is found in the pig irons produced by modern conventional blast furnaces in the steel industries. The necessary amount of carbon needed was 1/2 compared to conventional blast furnace to produce the unit weight of steel, if we applied renewable energy or nuclear power for the microwave excitations.

Jan 1, 2006

By Núbia Suely Silva Santos, Alexandre da Silva Crespo, Frederico Muylaert Margem, Sergio Neves Monteiro, Anderson de Paula Barbosa, Michel Picanço Oliveira

"Environmental considerations in addition to technical, economical and societal benefits are increasingly promoting the substitution of natural fibers for glass fiber in polymer matrix composites. However, natural fibers are heterogeneous in their dimensions, specially the cross section, which plays an important role in their mechanical strength. The fibers extracted from the petiole of the buriti palm tree is a relatively unknown but promising natural fiber for composite reinforcement. In this work, a statistical analysis of the density of buriti petiole fibers using the Weibull methodology was performed. An attempt to correlate the fiber density with the diameter, precisely measured by means of a profile projector, was carried out. The results revealed an inverse dependence between the buriti petiole fiber diameter and corresponding density. Fracture tip observation by SEM suggested a possible mechanism that could justify this inverse correlation.INTRODUTIONIn the past decade polymer composites reinforced with natural fibers obtained from cellulose-based plants, known as lignocellulosic fibers, have been applied in several engineering sectors, specially the automobile industry as both interior and outside component [1-4].Environmental benefits as well as economical, social, and technical advantages are actually promoting the substitution of these lignocellulosic for the traditional glass fiber in polymer matrix composites [5]. Today several lignocellulosic fiber are being extensively investigated [6-11] and considered for reinforcement of polymer composites. Some relatively unknown lignocellulosic fiber with reinforcement potential, however, still need to be characterized aiming at future application in composites. This is the case of the fibers stripped of from the petiole of the buriti palm tree, which is endemic in the central and northern regions of South America [12,13]. Preliminary works on the possibility of using the buriti petiole fibers as composite reinforcement, has shown favorable results [14,15]."

Jan 1, 2012

By Samir N. Shoukry, Mourad Y. Riad, Gergis W. William

"Setting of concrete material is defined as the transitional period between states of true fluidity and true rigidity. Initial and final setting times are measured in the laboratory on the mortar sieved from the mix in a controlled environment where temperature and moisture values are constant. On the other hand, field applications are held in outdoor environments where environmental variations have direct impact on setting time values. In this study, initial setting time of class K concrete, usually used for bridge decks and concrete pavements, are investigated highlighting discrepancies between laboratory and field measurements. 72 mixes have been cast in variable environments and collected data from concrete mixes and the ambient conditions are reported. In light of the collected data, the effects of variable setting times on early age cracking of concrete material are studied and means to minimize such cracks are presented.BackgroundSetting of concrete material is defined as the transitional period between states of true fluidity and true rigidity [1]. Continuous hydration of the cement within the matrix transfers the mix from a state of setting to hardening. Initial and final Setting times are measured in a laboratory setting following ASTM C 403 specifications. Initial setting approximates the time at which the cement paste can no longer be plastic under compaction (or can be handled in a proper fashion), while the final setting approximates the time at which hardening occurs. The standard test described in ASTM C 403 is conducted on the mortar sieved from the mix (paste passing from 4.75 mm sieve opening). Initial and final settings are described as the elapsed time after the initial contact of water and cement till the mortar reaches a penetration resistances of 3.5 MPa (500 psi), and 27.6 MPa (4000 psi) respectively."

Jan 1, 2012

By P. J. Harrington

The recovery and recycling of low concentration metal and other ions has traditionally been carried out using adsorption or ion exchange processes which, however, become uneconomical at higher concentrations, such as those that occur with many intermediate or waste streams where recycling is now being required. This paper describes the development of a process based on non-dispersive solvent extraction for the recovery of chromium (VI) from electroplating rinse water. During the chromium plating of steel, the concentration of chromium (VI) in the rinse bath rises to concentrations in the order of 100 mg/L when it becomes unusable and is then disposed of. The aim of this work was to investigate processes for recovery and recycling of the chromium in the rinse bath. The recovered chromium is required to be concentrated and purified before reuse. Tertiary amines have been shown capable of concentrating and purifying the chromium (VI) in solution. However, solvent extraction processes that have been applied to the recovery and reuse of metals from waste streams have had only limited success in the past, primarily because of the relatively high solvent losses when existing contacting equipment is used on low feed concentrations. Attempts to eliminate losses by immobilizing these complexing agents on substrates have not been successful. In order to control the losses and maintain specificity, a hollow fibre-contained liquid membrane has recently been trailed in a pilot plant to recover chromium from chromium plating waste streams. Details of the trial and modeling of the results are presented, and show that the level of losses is significantly reduced. However, issues relating to fouling still need to be addressed. This type of equipment has many applications in the recovery and recycling of a range of materials in the manufacturing processes.

Jan 1, 2003

By Anatoly Sudnev, Vladimir Skorohodov, Igor Kudryavtsev, Boris Radionov, Dmitriy Panov

"In cobalt production technology at a stage of solutions purification manganous cake (slime) basically containing hydroxides of the specified metals is formed. The possibility of full cobalt recycling in the basic technology of metal production at slime processing with generation of pure manganous compounds is shown. After slime dissolution in sulfuric acid in the presence of reducers the solutions containing cobalt, manganese, nickel and other nonferrous metals are formed. Optimum conditions of selective precipitation major part of cobalt by sodium hydroxide from the obtained solution are defined, thus more than 95% of manganese are remained in the solution. The cobalt precipitate is directed to the basic technology and the solution is purified by sorption. The most effective sorbents are chosen, optimum modes of its use are found. Examples of manganese recovery from the purified solutions as MnO2, MnCO3, Mn(OH)2 with a ratio manganese : impurities more than 3000 are presented.In the processes of hard alloys manufacture and processing of cobalt-bearing primary raw materials various cobalt-manganous slimes are formed. After leaching by solutions of mineral acids the problem of cobalt and manganese separation becomes an actual. The common way of metals separation in a solution is the Shreyber’ alkaline method allowing rather selectively to precipitate of cobalt hydroxide by sodium hydroxide. However this way does not allow separating completely target metals because of transfer of some manganese in the hydrated precipitate, even at its rather low content.In the given work the results of researches to improvement of a traditional way by inclusion to hydrometallurgical technology of operation of sorption separation of the specified metals are presented. The main goal is definition of conditions to achievement of the complete removing cobalt at hydrolysis with the minimum sedimentation of manganese and the subsequent additional recovery of cobalt by ionites from the obtained solutions."

Jan 1, 2008

By Ting Luo, Hongmin Zhu, Kai Huang, Shuanglong Du, Tao Gui, Yifan Xiu

"Poplar cotton, a cellulosic material, was found to adsorb metals ions effectively. In the present study, the biosorption characteristics of Pb(II) onto poplar cotton, were evaluated as a function of pH, contact time, biomass dosage, initial concentration and temperature. Within the pH range investigated (1.0-6.0), the optimal pH value suitable for the uptake of Pb(II) was determined. The maximum adsorption capacity obtained from the Langmuir model is around 0.52mol kg for the poplar cotton sorbent. Equilibration is achieved in 60min for the studied concentrations. Results suggest that the poplar cotton can be directly used as an effective and low-cost biosorbent for removal of Pb(II) from aqueous solution.IntroductionHigh value utilization of various biowastes produced in agricultural, forestry, fishing industries, etc. have attracted great interest from many researchers [1], Biomass, due to its easy availability, great abundance, low cost, easy processing, eco-friendliness and biodegradability, has exhibited exciting potential for being used as raw materials for the preparation of many new hi-tech functional products [2]. For example, using biowastes to synthesize sorbents for application in the removal of toxic substances such as dyes [3], heavy metals from the waste water [4] or in the recovery of valuable metals [5] from the ore tailings and secondary metals resources has made great progress in last decade. In present study, poplar cotton, a kind of white light fluff of poplar trees, like that of dandelion, usually flying in the air each spring was tested as a biosorbent for the remove lead ions from the water. It may also provide some good ideas for new sorbent design. Lead, as one of the typical poisonous heavy metals, for its typical toxicity and extensive pollution, was chosen to test the adsorption behavior of poplar cotton in aqueous solutions."

Jan 1, 2012

By A. Pagliero

The coulombimetric reduction method has been used as an evaluation technique for Pb-Ca-Sn anode corrosion in the LIX-SX-EW process. The proposed methodology involves three consecutive steps, i.e., cleaning, oxidation and reduction. They are carried out in the same experimental unit, in solutions containing 180 g/L H2S04 with and without the addition of cobalt. The authors have worked in a wide range of oxidation current densities, from 150 to 500 A/m2 for in a period from 0.5 to 120 hours. It can be concluded from the results that there would be a linear relationship between the applied electrical charge I*T (Coulomb) and the anode corrosion expressed as transformed Pb mass (mg), for solutions with or without the addition of cobalt. The exception is that for the last one the corrosion rate is 5 times faster, which was observed for every layer. From the evaluation of different corrosion layers, one can point out that its composition is mainly in the form of sulphate. In the presence of cobalt, about 67% of Pb would be as sulphate (PbSO4), about 27% as a basic oxide (PbO) and only 6% as oxide PbO2 on the surface. From this result, it appears that great transformations occurred in the metal/sulphate interface. Without the addition of cobalt, the proportion of oxide Pb02 on the surface increased up to 11.5%. According to the previous statement and considering that Pb was found mainly as sulphate, the authors recommend its determination be used as quality selection criterion. Its evaluation should be performed in the acid solutions with 200 ppm cobalt addition at an oxidation current density of 300 A/m2 for a period of 24 hours.

Jan 1, 1999

By Rauno Peippo

Horizontal Waste Heat Boiler (WHB), today's proven and dominating technology for copper smelter gas cooling, has been utilized by the industry for over half a century. During this time development has taken place in geometry, flow characteristics, cleaning technology and design details. This development has been driven by improved understanding of the specific process requirements, gained both by wide experience and by utilizing new emerging design tools, like computer flow modeling. It had to wait till mid 90's to unite effective and proven Spring Hammer cleaning technology and the process benefits gained by gas guiding vanes or baffle wall in the copper smelter WHB design. The new design has demonstrated improvement in gas cooling efficiency and the process conditions down stream in form of less dust sticking problems in the boiler and precipitators. Reduced weak acid production has also been reported as a result of the design. The theoretical aspects, computer flow modeling results and actual benefits measured in old smelting line modernization are discussed. Experience £tom modernization projects such as Phelps Dodge, Atlantic Copper, Mexicana de Cobre, and Nippon Mining, Saganoseki, are discussed. In mechanical design there has been development resulting improved gas tightness with less corrosion and better control of dust sulfation. An essential improvement is the integration of the boiler hopper and dust removing conveyor. Having no steel plate casings in the hopper and conveyor section but using of boiler tube membrane instead eliminates thermal expansion differences. The dust conveyor will be effectively cooled against hot dust lumps falling down while the acid dew point corrosion is prevented in the cooler sections of the hopper. Conceptual features are presented of a new generation Copper Flash Smelter WHB presently under construction at Boliden Mineral, Skelleftehamn, Sweden, where the latest development and innovations are adopted.

Jan 1, 1999

By Larry Southwick

This Peirce-Smith Converting Centennial symposium is celebrating the contributions of two men, William Peirce and E.A.C. Smith, in advancing technology allowing the copper industry to realize its full potential. However, theirs is representative of a larger story: New, simpler technology releasing the stranglehold of older, more complicated technology, new developments in vessel configuration and design finding alternate routes around dead ends in operability, advances in technique and concepts removing roadblocks of cycle time and capacity, and overall innovation opening up vast new reserves around the world to those companies willing to embrace those improvements. Our story is also one of personalities, stubborn smeltermen versus the innovators, those inside the industry versus those from outside. It is a story of an initial borrowing from the steel industry, but also Peirce and Smith, from the refining end of the copper business, taking the ideas of Baggaley from Pittsburgh’s steel and airbrake industry, who built on what Hollway, Manhès and David, Douglas, and others had done in smelter tests, further to compete with the previous primacy and closely held expertise of the copper smeltermen in Wales. These advances have been well recorded in photographs taken over the last 150 years. A number were submitted especially for this symposium. Many others were published in the mining and metallurgy press of the times. Several mining schools also retained copies of photos either taken during field trips, or donated to the school by alumni and operating companies. This presentation will provide a selection and discussion from these sources of “converters in action”, describing the various designs, operations and developments depicted. The focus here will be on the first roughly 60 years of copper converter development, from Bessemer’s days at the dawn of this new idea, up to and slightly past the time of initial adoption of Peirce and Smith’s designs.

Jan 1, 2009

By Che Xin, Liu Tianlong, Bi Hongyun, Chen Lijia

"High-cycle fatigue experiments were conducted at 800°C in laboratory air for three ferrite stainless steels including 15CrNbTi, 15CrMoNbTi and 18CrNbTi, where the stress ratio of 0.l was adopted. The experimental results show that at 800°C, the fatigue limit of the 15CrMoNbTi steel is the highest, the fatigue limit of the 15CrNbTi steel is slightly lower than that of the 15CrMoNbTi steel, and the fatigue limit of the 18CrNbTi steel is the lowest. At the same maximum stress, the 15CrMoNbTi steel has longer fatigue lives than the 15CrNbTi steel in the low stress area, while the 18CrNbTi steel has the shortest fatigue life. In addition, the observations on the fracture surfaces of fatigue specimens reveal that the fatigue cracks initiate transgranularly at the free surface of the specimens and propagate in a transgranular mode.IntroductionIn modem automotive industry, the manufacturers have paid great efforts to clean exhaust gas and to improve fuel economy. It is thought an effective way to increase the temperature of combustion chamber in automotive engine. And thus, the manifold closed to the engine in automotive exhaust system can suffer high temperature up to approximately 1000°C. Because of their relatively low thermal expansion coefficient, high yield strength at elevated temperature and good fatigue resistance, ferrite stainless steels, especially added with alloying elements such as Mo, Nb and Ti, are increasingly used for automotive exhaust systems [1-3]. In fact, exhaust manifold operated under high frequency vibration and exposed to high temperature exhausting gas also requires good fatigue resistance at elevated temperature. Some studies on the high temperature fatigue characteristics of stainless steel have been documented. It has beeen found that the fatigue limit of four ferrite stainless steels including 409L, 436L, 429EM and 444 (18Cr- 2Mo) reduces significantly with increasing temperature [4, 5]. In the research concerning the effect of a-phase embrittlement on fatigue behavior in a high-chromium ferrite stainless steel, it is noted that the precipitation of brittle a-phase will reduce the crack initiation and growth resistances and result in a decrease in fatigue limit [6]. In this investigation, the high-cycle fatigue behavior of three ferrite stainless steels including 18CrNbTi, 15CrNbTi and 15CrMoNbTi at 800°C have been studied to address the mechanical aspect of high-cycle fatigue behavior for ferrite stainless steels and to provide the theoretical reference for the safe design of automotive exhaust system."

Jan 1, 2013

By Christian Bernhard, Mario Hartl, Susanne K. Michelic

"One aspect of an efficient process and product optimization of the liquid steelmaking process is the understanding of reactions and interactions between the components steel, slag and nonmetallic inclusions. The present paper focuses on a fundamental study of this topic by combining the powerful methods of thermodynamic modeling with systematic experiments on a laboratory scale and subsequent SEM/EDS analyses. The modeling aspect is addressed by the commercial software FactSage 6.1; laboratory experiments are performed for a low-alloyed, Ca-treated carbon steel combined with varying slag compositions. The consequent SEM/EDS analyses provide a detailed insight into the inclusion landscape which offers a strong tool for characterizing the modification of inclusions. In the present study the combination of these methods is mainly applied to oxides, due to their crucial influence on the final product quality, thus giving important indications for further optimizing the secondary metallurgy processes.IntroductionIn recent years, the range of application for steels has been enlarged continuously; also resulting in extreme surrounding conditions combined with considerable stresses for the material. This trend is directly linked with higher demands on the properties of steels. In order to optimize the final product quality, the cleanness of steels is an important criterion. For this reason, the broad topic ""Steel Cleanness"" has become one of the main research points at the Chair of Metallurgy. Next to the continuous optimization of methods for the characterization of cleanness, the primary aim is to combine thermodynamic modeling and laboratory experiments in order to describe the changes in inclusion landscape under different conditions.The steel cleanness can particularly be influenced in the processes of secondary metallurgy. In different processes the reactions and interactions between the components steel, slag and nonmetallic inclusions (NMI) are essential for the final inclusion landscape. Consequently, the understanding of the occurring reactions is a fundamental aspect for further development and process optimization. In secondary metallurgy especially oxide-slag systems consisting of the components Ca0-Ah03-Mg0-Si02, which significantly influence the modification of NMI, are of importance. Several works dealing with the interactions of oxide non-metallic inclusions with different slag systems have been published in the last years [1-4]. In order to observe the dissolution of oxides in different slag compositions a Laser Scanning Electron Microscope is frequently used. A very detailed study on the ternary system Ah03-Ca0-Mg0 and its subsystems was also done by De Aza et al. [5, 6]."

Jan 1, 2011

By Mark Jolly, Nasim Soleimanian

"During the last 20 years CFD (Computational Fluid Dynamics) has been used as a tool to aid furnace designers and manufacturers to improve energy efficiency and effectiveness of glass furnaces. However as the models are maturing the effect of feeding equipment used to push the raw material into the furnace has not been included in the process models. This paper investigates the effects of batch pattern in the melt space caused by charging equipment on the energy efficiency of the furnace focusing on the melting zone. A simple batch patterns sensitivity study has been performed using purpose built software (Glass Furnace Model-GFM). It is concluded that in order to further reduce the energy consumption of the furnace it is necessary to model the batch charging process in more detail to find more opportunities for improvement.Introduction Glass manufacturing is a conservative industry which applies to all the four major segments (float glass, container glass, fiberglass, and specialty glasses). Risks due to the high capital investment, very long service life of the furnaces, and the demand for high performance and quality from the outset translates into evolutionary progress rather than revolutionary. The main problem facing glass manufacturers are the financial cost of manufacture, its impact on the environment, and mounting pressure imposed by the authorities for greener manufacturing and reduction in emissions.The main energy intensive activities involved in continuous glass manufacturing are: the need for high temperature to create and maintain the viscous flow, homogenisation of glass melt (melt residence time), and maintaining the two to achieve continuous output of glass at the right quality. The high temperature and long duration of homogenisation has resulted in the design oflarge furnaces, which have high energy consumption, low specific performance, and high C02 emissions. As an example in the container glass sector the most efficient furnace has a specific primary energy consumption of 3.8 GJ /tonne of glass at a level of 50% cullet in the batch. Even very small improvements in efficiency by optimising operation would have a high impact [1-14]. Given the conservative nature of the industry and the costs involved in experimental data gathering, CFD modeling of the process has been used extensively during last two decades to not only improve our understanding of the process but also as a tool in predicting possible optimisation windows, e.g. Glass Furnace Model ( GFM), a commercially available piece of software that has been developed to optimise furnace operation."

Jan 1, 2013

By John R. Howell

"SUMMARYThe process of producing a new cast component requires significant design and development by both the design engineer and the foundry engineer. This effort strives to produce a high quality component at minimum cost. To assist in this development, an analysis system, consisting of several computer programs, has been developed to simulate the metal casting process. This system incorporates analytical geometric solid modeling, finite element analysis, results display, and an innovative technique to model the casting mold with surface boundary conditions.The simulation has produced excellent thermal results and work is in progress to develop techniques to enable use of this data in additional analyses to predict porosity and residual stress. Research is required to produce working parametric formulations of material properties. Software development is required to develop good fluid flow analyses for large. 3D models to simulate filling of and convection in molds.Integrating this system of programs is difficult due to proprietary database structures used by software developers. However, an acceptable means has been accomplished' to move data from one program to another. Further software development is required to facilitate this task. INTRODUCTIONThe process of producing a new cast component requires significant design and development by both the design and foundry engineer. This effort strives to produce a high quality, reliable component at minimum cost in a timely manner. The design engineer needs to know the physical and mechanical properites which can be expected in the actual part at critical areas. This will enable him to design a part with minimum material while fulfilling the performance required. The foundry engineer needs to produce a sound, quality casting with a minimal amount of material In risers, the feeding system and machining stock. This must be done with a minimum· investment in tooling and development time and maximum productivity of labor and capital employed. This task Is continually being made more difficult because of increased competition in the marketplace and the use of castings in more severe service. This has strongly influenced the need for high quality castings.The task of developing a new casting is difficult for both the design and foundry engineer. To assist in this development, Deere & Company has been engaged in the development of an analysis system to simulate material processes. A major portion of this program involves simulation of the metal casting process. This analysis system has evolved into a package of computer programs which simulates casting solidification and subsequent cooling through the finite element method"

Jan 1, 1986

By F. Raupp-Pereira, G. G. Cunto, J. A. Junkes, D. Hotza, V. P. Della

"The present work investigated the valorization of wastes as alternative raw materials for ceramic industries. Different industrial wastes based on the SiO2-Al2O3-CaO system and classified as non-hazardous were selected: sludge from varvite cutting process, sludge from gneiss breaks processes, sludge from filtration/clarification of potable water and a clay classified also as waste. All as-received residues were characterized by X-ray fluorescence, differential thermal analysis, thermogravimetry and particle size distribution. The applicability of these materials in ceramic formulations was then evaluated. The formulated mixtures were subjected to forming by pressing and extrusion followed by thermal treatment. After optimization of the processing conditions, the properties of the samples sintered at different temperatures were also evaluated. The waste materials studied proved to be alternative raw materials to natural mineral resources for the ceramic industry.IntroductionOne of the most important problems that have accompanied the humanity in recent decades is the environment’s degradation. In the same context, the natural resources exploration and technological development are phenomena which, if aren’t controlled, can cause ecological disequilibrium with unpredictable consequences [1]. It is in this perspective that recycling of various wastes assumes relevant importance.The recycling, understood here as the waste process reuse, is a common practice in the First World countries, where the raw materials have strategic aspects and the disposal techniques of solid wastes have considerable economic costs. In Brazil, the ecological conscience begins to be aroused due to, in the last ten years, the implementation of stricter laws for environmental control, in general, and licensing of waste generating from industrial activities, in special. The terms “residue” or “waste” are normally used to describe what remains of a production process; when an application for this material is not found. When wastes or residues are susceptible to be incorporated as raw materials or energy sources in a new material production, they can be understood as by-products [2].The valorization of industrial wastes is important, due to the need to pollute less and give an ecologically correct destination for wastes. The waste recycling, independent of its kind, presents several advantages in relation to using primary natural resources, such as reduction in the volume of raw materials extraction, lower energy consumption, lower levels of pollutant emissions and improvement of the health and safety of the population. The most visible advantage of recycling is the preservation of natural resources, extending its life and reducing the destruction of landscape and ecosystems [3]."

Jan 1, 2008