Search Documents

By Bernhard J. Ralph

In refractory gold ores much of the gold occurs in sub-microscopic form in sulfide minerals, most commonly pyrite and arsenopyrite Bacterial leaching is being developed as a pretreatment for these minerals to aid the liberation of gold and a variety of extracting reagents. This paper reviews the nature of the principal micro-organisms involved, the effects of various physico-chemical factors on the rate and extent of extraction, and likely mechanisms involved.

Jan 1, 1989

By T. Lezhava

Recycling technology of spent Mn-Zn system batteries has been worked out and tested in laboratory scale. The proposed technological scheme includes the following basic operations: breakage of batteries, hydro-vibrated treatment of broken up mass, electrolysis by using alkali electrolyte. This method enables extracting of 200-220 kg zinc in powder form, of 300-350 kg manganese concentrate and of 130 kg steel in the form of scrap per tone of broken up batteries.

Jan 1, 2006

By Sharif Jahanshahi

Calcium ferrite slags are often associated with Professor Yazawa due to his pioneering work on the thermodynamics of this type of melts. Over the past years CSIRO has invested some effort in studying physico-chemical properties of such melts to fill in some gaps in our knowledge and explore opportunities for application of the understanding developed. These investigations cover thermodynamics, transport properties of calcium ferrite based slags, as well as the kinetics of reactions of such slags with refractories. The present paper provides an overview of some of these studies and highlights some of the interesting behavior of such melts. The oxidation state of copper and arsenic in calcium ferrite based slags are predominantly Cu+ and As3+, respectively, at oxygen potentials below 10.1 atm. The concentration ofCu2+ in such slags becomes significant at oxygen potentials of greater than 10'1 atm at 1300 ?C. The activities of CuOo.s and AsOl.S in calcium ferrite slags show strong deviations from the Raoultian Law, while that of CoO is very close to ideal behaviour with respect to pure solid CoO. Addition of Si02 to calcium ferrite slags can have significant effects on the activities of FeO and Fe2O3 and hence the stability of magnetite phase. Transfer of oxygen in calcium ferrite slags is fast with diffusivity of 2xlO?3 cm2/s at 1350 °C and activation energy of 16 kcal/mol Presence of solid phases, such as magnetite, has pronounced effect on the viscosity of calcium ferrite slags. The observed dependence on solid loading and shear rate indicates deviation from Newtonian behaviour. The interfacial tension between copper mattes and calcium ferrite slags is strongly dependent on the matte grade, with the determined values being much lower than the corresponding ones for interfacial tension between similar mattes and iron silicate slags. MgO, Cr2O3 and MgCr2O4 have low solubility in calcium ferrite slags and their solubility increases with increasing copper oxide content of the slag at 1300 °c. The oxidation state of the slag has strong effects on phase transformation, dissolution rate and disintegration of refractories in calcium ferrite slags. Other key factors with major impact on slag-refractory interactions include viscosity and surface tension of slags as well as the contact angle between slag and refractory material.

Jan 1, 2003

By Sharif Jahanshahi

Calcium ferrite slags are often associated with Professor Yazawa due to his pioneering work on the thermodynamics of this type of melts. Over the past years CSIRO has invested some effort in studying physico-chemical properties of such melts to fill in some gaps in our knowledge and explore opportunities for application of the understanding developed. These investigations cover thermodynamics, transport properties of calcium ferrite based slags, as well as the kinetics of reactions of such slags with refractories. The present paper provides an overview of some of these studies and highlights some of the interesting behavior of such melts, The oxidation state of copper and arsenic in calcium ferrite based slags are predominantly Cu+ and As3+, respectively, at oxygen potentials below 10-7 atm. The concentration of CU2+ in such slags becomes significant at oxygen potentials of greater than 10-7 atm at 1300 °C. The activities of CuO0.5 and AsO1.5 in calcium ferrite slags show strong deviations from the Raoultian Law, while that of CoO is very close to ideal behaviour with respect to pure solid CoO. Addition of SiO2 to calcium ferrite slags can have significant effects on the activities of FeO and Fe2O3 and hence the stability of magnetite phase. Transfer of oxygen in calcium ferrite slags is fast with diffusivity of 2x 103 cm2/s at 1350 °C and activation energy of 16 kcal/mol. Presence of solid phases, such as magnetite, has pronounced effect on the viscosity of calcium ferrite slags. The observed dependence on solid loading and shear rate indicates deviation from Newtonian behaviour. The interfacial tension between copper mattes and calcium ferrite slags is strongly dependent on the matte grade, with the determined values being much lower than the corresponding ones for interfacial tension between similar mattes and iron silicate slags. MgO, Cr2O3 and MgCr2O4 have low solubility in calcium ferrite slags and their solubility increases with increasing copper oxide content of the slag at 1300°C. The oxidation state of the slag has strong effects on phase transformation, dissolution rate and disintegration of refractories in calcium ferrite slags. Other key factors with major impact on slag-refractory interactions include viscosity and surface tension of slags as well as the contact angle between slag and refractory material,

Jan 1, 2003

By Mikiya Tanaka, Mikio Kobayashi, Mansour A. S. A1Ghamdi, Kenji Tatsumi, Yukinori Saiki, Hirotaka Senba

"In order to recover nickel ion in a spent electroless nickel - phosphorus alloy plating bath and, at the same time, to remove impurities such as iron and zinc, the applicability of solvent extraction with LlX84I as the extractant has been investigated using actual spent solution. Although the extraction efficiency of nickel from the spent solution is considerably lower than that from the nickel sulfate-nitrate solution, nickel in the spent solution is selectively extracted with high efficiency at the pH of 6 - 7. The extracted nickel is effectively stripped by sulfuric acid at a pH of less .than· 3. On the basis of these results, a· flowsheet for recovering nickel from the spent solution is proposed Chemical equilibrium calculations of the spent solution has shown that the complex formations of nickel with anions such as lactate and phosphonate ions become predominant in the pH range between 2 and 6. This results in the depression of nickel extraction efficiency from the spent solution as compared with that from the .nickel sulfate-nitrate solution. By combining these aqueous equilibrium calculations with the· extraction model considering the extraction stoichiometry and the aggregation of the extractant in the organic phase, the extraction behavior of nickel is quantitatively predicted.IntroductionElectroless plating is indispensable for the recent advanced industries such as the electronic and mechanical industries. Electroless plating baths are repeatedly used by supplying the metal salts; however, the accumulation of the counter anions of the metal ions, the components formed by the oxidation of the reducing reagents in the plating baths, and the metal ions as impurities dissolved from the surface of the objective materials degrades the· quality of the plating. Thus, the baths are finally treated by a precipitation method to form a large amount of metal sludge, which is disposed in dumping sites. Therefore, from the standpoints of environmental protection and resource preservation, it is highly desired to establish a recycling process of the plating baths with minimum emission. Solvent extraction seems to be one of the 'suitable methods to recover metals from the spent electroless plating baths, because the concentration of the metal ion in the baths is relatively high, which is advantageous to solvent extraction as compared with the ion-exchange and adsorption methods. Some studies about the application of solvent extraction have already been carried out using simulated spe11t electroless plating baths [1-3]."

Jan 1, 2000

By John P. Hager

One possible approach for the recovery of mercury from acid plant blow-down sludge in smelters is the use of a vacuum retort reactor for the vaporization of the mercury with subsequent collection of metallic mercury in an attached condenser. An experimental study was undertaken to investigate the vaporization of mercury when present as a compound in the Hg-S-O and Hg-Se systems. A transpiration reactor was modified to operate under reduced pressure and with a continuous flow of inert sweep gas. A water-cooled cold finger was inserted into the exit end of the reactor to provide for the rapid quenching of the exit gases and the collection of the mercury. Rates of vaporization were measured at several temperatures for each compound and were generally found to be constant at a given temperature and reactor pressure. The results were used to determine the minimum operating temperature for 100% vaporization of the compound in 60 minutes. For Hg2SO4, HgSO4, and HgSO/2HgO the required temperatures. for a reactor pressure of 50 Torr. were determined to be 634°, 622°. and 603°C. respectively. For HgO, HgSe, and HgS the required temperatures were 557°. 451°. And 382°C. respectively. For HgS the rate of vaporization was also measured at a reactor pressure of 1 00 Torr. The rate of vaporization was found to be slower resulting in an increased vaporization temperature of 423°C. It was also determined that the mercury vapor present in the exit gas stream can back-react with the other gas species to a significant extent and can result in very little condensed metallic mercury. For the vaporization of both HgS and HgSe. the mercury vapor was found to have back-reacted to the extent that virtually none of the vaporized mercury was collected in metallic form. For the vaporization of Hg2S04? HgS04, and HgSO4*2HgO the amount of metallic mercury recovered varied from approximately 50% for HgS04*2HgO to approximately 10% for Hg2S04 and HgS04. Only for HgO was the recovered mercury in primarily elemental form. The application of the results to the operation of a vacuum retort and condenser system is discussed.

Jan 1, 2001

By Y. Houbaert, L. Kestens, R. Decocker

"A magneto-elastic model is presented to calculate the orientation dependence of the magnetostrictive strain, observed at saturated magnetisation in ferromagnetic materials with a cubic crystal structure and an arbitrary crystallographic texture. The formula of Becker and Doring is used to express the anisotropy of magnetostriction for a single crystal. In order to simulate the macroscopic average magnetostriction of a polycrystalline aggregate (with an arbitrary texture) the Reuss assumption of the elasticity theory was applied. According to this assumption the various orientations of the polycrystal can defonn without constraints, producing local strain incompatibilities in the microstructure but observing total stress equilibrium. The macroscopic strain is calculated as the weighted average of the individual strains of all orientations composing the polycrystal. The weight factors are determined by the volume fractions of the corresponding orientations of the given texture, which can be measured by standard X-ray diffraction techniques. The model is applied to simulate the variation of magnetostriction (at saturation) with respect to the rolling direction for a standard grade of Goss-oriented electrical steel. A brief comparison with experimental data allows validating the basic model assumptions. IntroductionBecause of tougher environmental constraints, the noise reduction in transformer cores has become increasingly important. It is generally accepted that the main source of noise is magnetostriction, which is known to be caused during the magnetisation process by the movement of 90° magnetic domain walls and the rotation of the magnetisation vector out of the easy directions. Therefore, it is obvious that when a ferromagnetic body is magnetised to saturation, the resulting magnetostriction will be dependent on the distribution of magnetic domains in the initial state.In the literature two coefficients are used to describe the resulting magnetostriction at a saturating magnetic field. The total strain, measured from an arbitrary demagnetised state to technical saturation, is called the saturation magnetostriction, and is denoted by (~)s. The tenn magnetostriction coefficient will be employed to designate the strain measured from the ideal demagnetised state (i.e. one in which no preferred orientation of domains exists) to technical saturation. Failure to recognise the difference between these two quantities has led to considerable confusion in the literature.The magnetostriction coefficient for a single crystal is a well-known property for ferromagnetic cubic materials. In 1939 Becker and Doring [1] have derived the following relation, describing the magnetostriction coefficient for single crystals with a cubic symmetry:"

Jan 1, 2001

By Hani Henein

"Heat transfer between droplets/particles and a gas phase plays an important role in the transport of numerous materials processing operations. These include rapid solidification operations such as gas atomization and spray forming, as well as chemical systems such flash furnaces. Chemical reaction rates and solidification are dependent on the rate of gas-particle or gasdroplet heat transport. Using a heat transport model validated using single fluid atomization of molten droplets; the effect of process variables on heat losses from droplets was examined. In this work, the effect of type of gas, droplet size, gas temperature, gas-droplet relative velocity on the heat transport from AA606 l droplets was examined. The most critical of these process variables to heat transfer is identified and will be presented.IntroductionIn materials processing, droplets are often encountered and used in processing a wide range of liquids and slurries. The small size of the droplet enables high reaction rates or high solidification rates in many systems. In order to capitalize on these high rates of transport processes, sprays are· also developed to maximize throughput. The design of these sprays, however, does not account for the transport steps and rate limiting mechanisms at the droplet surface. Rather, spray design focuses on maximizing the break-up of a stream or slurry into small size droplets or controlling the spread of the spray. Spray systems in industrial use typically generate droplets of wide size distribution leading to a wide range of reaction times for each of the droplets. Often the generation of a spray involves a number of coupled phenomena such as stream break-up, droplet-gas transport, droplet size distribution and spray geometry. Using gas generated sprays, it is not possible to identify how individual process variables contribute and control each of these coupled phenomena. While many mathematical models have been developed of sprays and they attempt to simulate coupled droplet transport, they do not provide insight into the contributions of different mechanisms in heat transfer. This is primarily because the basic fundamental heat transport between droplet and gas cannot be isolated from other gas spray phenomena experimentally such as two-way thermal coupling [l]. Thus, experimental validation of heart transfer of large and complex industrial spray models is not carried out. Hence, the validity of spray models remains in question and the approach required to optimize spray processes cannot be clearly identified"

Jan 1, 2004

By Jing-she Li, Hai-yan Tang, Cheng-song Liu, Wei Liu

"In order to effectively utilize cheap and low quality iron ores, a hematite ore in a certain steel plant in Xinjiang was researched on to obtain ""iron increase and silicon reduction"" by ore dressing operation experiment and the performance indexes of the hematite ore were optimized. Based on the fundamental characteristics and high-temperature properties of the concentrate after ore dressing and other five kinds of iron ores which were co=only used in this steel plant, ore matching principles were proposed and a sintering ore blending optimization model was established. Finally, sinter pot test was carried out to verify the validity and practicability of the sintering ore blending optimization model which was aimed at giving consideration to the sintering indexes and the cost.IntroductionIn recent years, the price of imported iron ore with high quality is always at a high level, while iron ore self-sufficient rate in China is less than 50%. Enormous market demand and high dependence of domestic enterprises on imported iron ore makes the price of it hardly return to rational. In order to get rid of the situation of long-term meager profit and even deficit, more and more iron and steel enterprises in China transit their focus of reducing production cost to the utilization and development of relatively cheap but low-grade iron ore resources at home[l-4l_ However, besides the disadvantages of low iron grade, high content of impurities and complex embedded properties, the high-temperature properties of iron ore often go beyond the suitable ranges for producing sinter with high quality. Thus directly utilization of this kind of iron ore without ore dressing process would probably affect the metallurgical performance and indexes of sinter ore.Previous research and production practice have shown that traditional iron ore matching in sintering mainly focus on the reasonable collocation of properties of iron ores with low quality and high quality, but pay less attention to ore dressing process of low quality iron ores and matching them with high quality iron ores. Actually, compare with directly utilization, iron ores with low quality after ore dressing have higher suitability for matching with high quality ones which is beneficial to reduce the consumption of iron ores with high quality and control the production cost of sintering [5-s1."

Jan 1, 2014

By Riyad N. Ahmad-Bitar, Shadia J. Lkhmayies

"CdSi-xTex thin films were prepared by first producing CdS:In thin films by the spray pyrolysis (SP) technique and then annealing the films in the presence of Te vapor in nitrogen atmosphere. X-Ray diffraction (XRD) measurements showed that the films are polycrystalline with the wurtzite structure. Transmittance measurements were recorded at room temperature in the wavelength range 400-900 nm and used to deduce the absorbance. The first derivative of the absorbance was calculated and used to find the values of the bandgap energy, where more than one bandgap was obtained for each film. These results show that the films are inhomogeneous or the composition differs with location. The photoluminescence (PL) was recorded at T = 60 K and a deconvolution peak fit was performed for each spectrum. The results of the PL spectra are consistent with those obtained from the first derivative and confirm the inhomogeneity of the films.IntroductionPolycrystalline thin film CdS/CdTe solar cells are promising candidates for low cost and high efficiency photovoltaic applications. The CdS/CdTe interface plays an active role and a detailed knowledge of its properties is crucial for thorough understanding of the device. High efficiency devices have been obtained in spite of the large lattice mismatch (9. 7%) between hexagonal CdS and cubic CdTe. Interdiffusion at the CdS/CdTe interface is considered to affect the performance of the devices [1]. The formation of a mixed crystal or a graded layer at the interface causes a reduction in the lattice mismatch at the CdS/CdTe junction [2] and then a reduction in the number of interfacial states and recombination centers, thus enhancing the solar cell performance [3, 4].The objective of this work is to investigate the transmittance, photoluminescence (PL) and structure of CdSi-xTex thin films prepared by annealing the spray-deposited CdS:In thin films in the presence of tellurium vapor. X-ray diffraction (XRD) was used for exploring the structure. Transmittance is used to deduce the absorbance where its first derivative was used to find the bandgap energy which varies with composition. The evolution of the PL spectra as functions of tellurium concentration was evident and it confirmed the inhomogeneities of the films."

Jan 1, 2011

By Ying Li, Xuling Chen, Xiaohui Fan

"In the sintering process, the behavior and performance of iron ores is extremely complex. Different minerals have different sintering properties. In order to use iron ores rationally and effectively, multilevel fuzzy evaluation method is used to establish the comprehensive evaluation model of iron ores. Because of the relative independent characters of iron ores in sintering process, the characters can be divided into physical and chemical properties, granulation performance, and sintering properties, are divided, and together with iron ores prices as the first level index for judging, which are used as the second level index for judging. Using the analytic hierarchy process (AHP) to determine the weight of each index, which is used as the second level index. The relative membership matrix is determined by triangular membership function, the comprehensive evaluation model is established.IntroductionIn China, sintering is the main method for iron ores agglomeration. Sinter accounts for more than 80% of the blast furnace. Sinter production in the iron and steel enterprises in China plays an important role[l-2]. As the main raw material of iron ores sintering, the objectivity and integration of iron ores evaluation is essential. The iron ores evaluation methods include of metric ton price evaluation method, iron grade of a single iron ores sintering, acid-base balance method, composition assessment method and other methods which are based on the chemical composition and physical properties of iron ores to measure the quality of iron ores[3]. The high-temperature mineralization is an important process in sintering process, which affects the structure and mineral composition of the sinter, and has a close relationship with the quality of the sinter[ 4]. Therefore, in consideration of the physical and chemical properties, granulation properties, mineralization performance and sintering properties, the iron ores are evaluated by multi-level fuzzy comprehensive evaluation. The multi-level fuzzy comprehensive evaluation method makes a comprehensive evaluation, applying fuzzy transform principle and maximum membership degree principle, considering a number of factors related to the things which are evaluated. The method has lower requirements for the amount of data, and which integrates qualitative with quantitative judgment. It has a unique advantage to make up for the deficiencies of traditional evaluation methods. It also can comprehensively evaluate the iron ores in a relatively short period, reduce a lot of experiments, improve efficiency and guide the sinter production[5-6]."

Jan 1, 2013

By Rumen Markov, Lubomir Kuzev

"The treatment technologies for municipal solid waste (MSW) are effective mainly for components sized over 40 – 50 mm. This fraction is separated by screening in the beginning of the process. Usually the undersized product is deposited without additional treatment. Its quantity is variable from several up to 30 – 40 % of the total MSW. Both oversized and undersized fractions are formed by all types of primary matter. Adapted technologies from mineral processing will provide a suitable technology for treatment of MSW under 40 – 50 mm. The MSW content depends on the geographical location, the degree of urbanization and other factors. The methods can be applied for separations of different components suitable for recycling or other utilization are: • Separation by density; • Separation in thin liquid layer; • Selective grinding and screening; • Flotation, etc. Introduction Municipal solid waste (MSW) represents an integral part of public urbanization. However, there are some drawbacks stemming from MSW, in regard to its collection, transport and elimination. Different approaches exits worldwide for tackling the problems arising from MSW. For a short period of time, the attitude towards MSW has evolved in several levels, each further level being characterized by higher percentage of utilization of MSW components. Thus, the bottom line has been shifted from safety storage towards processing that includes recycling and maximal utilization of MSW components. Technologic processes applied for treatment of MSW have a common feature – that the fine components, having sizes under 20 mm, 30 mm, 40 mm, or 50 mm are excluded from treatment process trough screening, and in most cases diverted without any additional treatment to preliminary prepared storage sites. MSW in Sofia – current situation The amount of MSW collected daily in Sofia as around 1000 t/24 h. It is stored or baled. Baling is a spare alternative of storage, since baling insures only temporal keeping of MSW, till the building of suitable storage site where the bales will be transported and buried. The morphologic composition of MSW in Sofia has been determined several times at different time intervals, from some Bulgarian organizations as well as from the Japanese organization JICA. So far, however, there is still a lack of enough systematical and comprehensive study. Generalized results from the studies on the MSW components, as well as some important parameters are given in Table 1."

Jan 1, 2008

By M. Save, N. Menad

"This paper gives the overview of different alternatives to recycle the following wastes: slag, dusts, wastes of electric and electronic equipment (WEEE) and auto shredder residues (ASR). Based on modified Bogue calculations, steelmaking slags were combined in order to produce a belite-rich clinker activated with sulphoaluminate. The EAF dusts containing significant amount of metals can be recycled in different ways: The carbothermal treatment and INTECT process are reported. The results obtained from the model of Auto Shredder Residue injection into blast furnace show that ASR can be used as reducing agent in the BF process if certain conditions are met. The particle size of this material must be controlled to ensure optimal gasification of the material in raceway. The non-ferrous contents may affect the pig iron quality, which is difficult to rectify at a later point. It seems the pyrolysis is the most attractive process to handle ASR. The BRGM flow sheet of WEEE treatment is also reported.I. Introduction The activities of human been may generate wastes and by their accumulation during several years, these wastes may have an impact on the environment and on the human health. These wastes can be generated in the forms of solid, liquid and gas. A variety of industrial wastes can be recycled for use as products. There are three ways in which industrial waste recycling occurs: at the facility itself (on-site recycling), at commercial facilities that gather waste streams from several companies (off-site recycling), and at a company that uses as inputs in its production process the waste products of another company. The industries producing iron and steel may generate different solid wastes which are classified in three main categories: 1. Ferrous material (mainly dusts and sludges from gas cleaning), 2. Slags (these by-products are generated from different process stages), 3. Others by-products (including refractories and material generated from engineering activities). According to this review, the most quantity of the metallurgical wastes is deposed. Currently, the public opinion opposes the creation of new sites. This leads to the growth of the waste disposal costs. Such situation reduces the enterprise competitiveness and decreases their market share on regional and/or national and/or world scales. In these conditions, the economical activities can be decreased leading probably to social problems. The problem of wastes and/or by-products can be treated on three levels:"

Jan 1, 2008

By Emilia Visileanu, Eftalea Carpus

"The strategy of developing the Romanian textile industry sub-sectors envisages the achieving of certain superior production indices, from a physical and value point of view, in 2010, a quantitative increase of textile wastes by 14% in 2010 as compared to 2000, implicitly. The percentage of the turned-to-profit wastes will have an increasing tendency, from 53.6% in 2000 to 74.7% in 2010. The article synthetically presents the innovative elements of the technology of processing the industry textile wastes.1. Introduction“People will need to re-adopt this sense of rarity that has been forgotten over the last two centuries. Humans need to collect, sort, recover, going back to the old ideal of alchemists: complete the material cycle, turn waste into resource, reduce all forms of predatory behaviour as much as possible”Irrespective of the historical period, geographical positioning, economic power or employed technologies, wastes resulted and will result in a bigger or smaller quantity as long as life and activity on Earth go on. The negative effects of these over the environment factors and implicitly over population health are well known all over the world and not approaching this matter enough may have catastrophic consequences over life. Having in view these aspects, finding solutions for diminishing the general waste quantity and limiting the negative effects of those products is important, by effecting the reusing of the recyclable ones in the production processes as secondary raw materials, and by ecologically treating and storing those than cannot be reused.2. Experiments and researchesThe textile industry affects the environment by the high water, energy and chemical consumption, as well as by the high quantity of wastes that are the result of using an impressive number of chemical substances and technological processes.The development strategy of the Romanian textile industry sub-sectors foresees, for 2010, the achieving of certain higher production indices as compared to 2000, both in terms of materials (as merchandise) and in terms of value, which implicitly leads to a quantitative increase of wastes.The flexible, economic and ecologic technologies which include systems of waste preliminary preparing (cutting, opening) and conventional or non-conventional system of processing the recovered fibres lay at the basis of substantiating the activity of implementing the notion of zero wastes."

Jan 1, 2008

By S. K. Kawatra

"A typical steelmaking facility produced 50,000 tons per year of slag in their hot-metal desulfurization process. This slag had a sufficiently high iron content that it could be beneficiated and recycled in a blast furnace, provided that the slag could be agglomerated into pellets suitable for use as blast furnace feed. In this work, beneficiated slag was agglomerated using both a conventional bentonite binder, and a fly-ash-based binder (FBB) that was formulated by the investigators. The FBB consisted of a combination of highcarbon fly ash with calcium hydroxide activator, allowing the FBB to exhibit binding properties when moistened. It was determined that beneficiated slag agglomerated with FBB had superior compressive strengths compared to slag agglomerated with conventional bentonite binder. The FBB is therefore a satisfactory method of binding the agglomerated slag. Since the fly-ash component of the FBB is commonly discarded as waste, this approach also provides a means for utilizing high-carbon fly-ashes that currently have very little commercial value.IntroductionIn 2006 approximately 72.4 million short tons of fly-ash were produce in the United States [1]. The majority of fly-ash which was used that year was consumed concrete, structural fills, and cement. It is also used in road base, aggregate, and other applications. However, 55.2% of the fly-ash produced in 2006 was not utilized and ended up being sent to a landfill. Essentially all of the land filled fly-ash could be a suitable binder for pelletizing desulfurization slag and other steel plant waste oxide materials. Fly-ash based binders (FBB) have been shown in laboratory studies to be suitable for producing iron ore concentrate pellets of equivalent strengths as those bonded with bentonite [2,3,4]. The utilization of highcarbon fly-ash within the market is important for reducing the volume of currently unmarketable and land filled fly-ashes. FBB would be a much cheaper alternative to the current bentonite binder or organic binders used for iron ore concentrate and would help to reduce pellet costs. Currently, transportation more than doubles the final cost of bentonite since it is produced hundreds of miles from the pelletizing plants, while fly-ash is produced from power plants located nearby pellet plants and steel mills. FBB’s also show promise for use in other high volume applications such as foundry sand mold binders."

Jan 1, 2008

By Adam Gesing, Paul Marchwica, Jerry Sokolowski, Sharon Lackie

"Often referred to as SEM-EDX, energy-dispersive spectroscopic analysis of characteristic fluorescence x-ray is a standard technique for semi-quantitative elemental composition analysis in scanning electron microscopy. It is quick and extremely useful for identification of phases in the sample microstructure, as long as the constituents are significantly larger than the probe volume from which the fluorescence x-rays originate. The probe volume ranges from a few to several microns, depending on the electron beam spot size and the acceleration voltage. We report on a new variant of an EDX technique developed to overcome this limitation and allow quantitative elemental analysis of smaller phase constituents, down to a size of several nanometers. This variant involves the calculation of compositions of individual phases from multiple analyses of areas containing phases of interest. This significantly increases the usefulness of EDX for quantitative analysis of new nano-structured materials.IntroductionIn any elemental micro-analytical method, the sample material is illuminated by a probe beam that excites an interaction volume of a sample to emit a characteristic signal. This signal in turn interacts with the sample material through absorption and fluorescence mechanisms before a portion of it is collected by a suitable detector and analyzed for elemental composition. The spatial resolution of the method depends on the minimum interaction volume between the probe beam and the sample material.Laser light beams can be tightly focused to a spot size limited by the photon wavelength and can be used to sample the surface of any material. In micro-LIBS (laser-induced plasma spectroscopy) a focused laser beam ablates and vaporizes a small volume of material from the sample surface, creating a plasma spark. Spectral analysis of the light emission from the plasma spark allows the semi-quantitative determination of the elemental composition of the material removed from the sample surface. The smallest reproducible craters achieved are ~ 3mm in diameter and a few nanometers in depth. [l]Particle probe beams of ions or electrons can be focused to a diameter of a few nanometers at the point of impact on the sample. Ions sputter the sample atoms from the point of impact, and the sputtered ionized material is analyzed by mass spectroscopy in a secondary ion mass spectrometer (SIMS). [2] This gives SIMS resolution in a nanometer range. SIMS equipment, however, is expensive and not readily available."

Jan 1, 2013

By T. A. Chepushtanova, B. Mishra, E. O. Kilibayev, V. A. Luganov

"The paper contains the results of studying about modification of pyrite and arsenopyrite specific surface and porosity at their thermal decomposition. The studying of specific surface was carry out by B.E.T. – adsorption of nitrogen at his boiling-point. In our work were using the electron-microscopical, X-ray structure analysis and chemical analysis. There was established that the decomposition of pyrite and arsenopyrite accompany by increasing of pores volume from 0.303 · 10-3 to 1.23 · 10-3 at increasing of pyrite degree of decomposition about 41 % and then decrease about 0.131 · 10-3 m3/g at degree of decomposition near 100 %. The surface area of pores increase from 0.31 to 1.085 m2/g with following lowering due to enlargement and confluence of minor, small pores. Increasing of porosity accompany with increasing of particles windage that appear the result of heightened dust-furnace partially decomposing pyrite and arsenopyrite particles by air flow from furnace reaction zone. This explains heightened contention of sulfide sulfur in roast dust of sulfide concentrate. 1. INTRODUCTION As a result of ore base exhaustion of ferrous and nonferrous metallurgy at metallurgical treatment are involving more complicated and less qualitative ores. Magnetiting ores content considerable quantity of pyrite complicative the technology of iron extraction. At the same time the pyrite concentrates wining at dressing content different nonferrous metals in industrial quantities. Extracting ores of nonferrous metals are contenting considerable quantity of arsenic at the present time. Extraction of base metals from complicated raw materials demands new technologies. Arsenic contenting in ores is necessary to utilize (waste burial) in more ecological compatible form. Arsenic on acting metallurgical and chemical enterprises from technological cycle is withdrawing in the form of arsenate – arsenite cakes, burial of their may lead to seriously ecological problems as times goes by. In Kazakh National Technical University is carry out the cycle of researching by pyrite, arsenopyrite and arsenate – arsenite cakes treatment with the object of arsenic withdrawal in sulfide form – in more ecological and safe form and with the object of preparation of initial ore raw materials to following pyro- and hydrometallurgical treatment. As a result of sulfidizing of arsenate – arsenite cakes by pyrite are forming the volatile arsenic forms and pyrrhotite of variable structure."

Jan 1, 2008

By D. Q. Cang, G. Duan, H. X. Li, H. Bai

"Life cycle assessment (LCA) is a valid environmental evaluation method and enterprise environmental management tool used in industrial ecology areas. In this paper LCA was newly used to evaluate the environmental impact of manufacturing of alumina by Bayer process in china from two aspects of logistics and energy flow, GaBi software acted as analysis tools with evaluation model established, and several environmental impact assessment criteria were selected based on the actually typical date of Bayer alumina producing process. Evaluation results show that alumina manufacturing by the Bayer process has a great impact on the global warming and human health of respiration, even roasting process gives rise to the greatest impact of winter fog index. Scenario analysis proposed ways of reducing environmental load caused by Bayer process including: (1) the economic and efficient use of mineral processing technology; (2) optimization of energy use, saving power consumption or the use of new more economical source of energy; (3) actively promote the use of innovated technology and equipment in alumina manufacturing and waste such as red mud utilization process.1 IntroductionSince 2002, China is already the world's biggest producer of aluminium, in 2007, China aluminum production has accounted for above 1/3 all over the world, 2009 for 13 million tons and to the end of 2010, China aluminum production is expected increased to be over 15 million ton [1,2,3]. While as the raw material for producing aluminum the alumina production in china has up to 19.46 million tons of the world's total quarter in 2007, by the end of 2009 China alumina production has achieve to 23.78 million tons [4,5]. China has rich bauxite resources with proven reserves about 23 million tons, but the great majority of china bauxite is hard monohydrate diaspore type with low ratio of aluminium silicon, high impurity content and poor aluminum dissolution performance, that cause high energy consumption, long and complex process, high production costs and heavy environment load[6,7]. Before most used alumina production was sintering process rather than Bayer method in china, over the past decade Bayer method has been widely applied instead of sintering process or combination both forming joint process, premise is improving bauxite quality by mineral processing or adding imported rich bauxite mineral[6,8]. In general each ton production of alumina needs bauxite 1.6~2.20t, limestone 0.7~1.7t, soda 0.250kg, fresh water 12.30 cubic meters, in addition to consume large amounts of energy, and emission waste water over 8.0 cubic meters, dust 2.3~5.7 kg, red mud 0.8-1.5 tons. In china Red mud yield nearly 30.0 million tons every year, accumulated stock is approximately 0.2 billion tons, by 2015 accumulative total red mud is expected to reach 0.35 billion tons [9-13].We know aluminium industry and alumina production have produced large waste, make large energy consumption and its environmental impact could not be ignored. Expecting to optimize production processes and achieve resource recycling for this industrial process the proper environmental assessment is very necessary. Currently Life Cycle Assessment (LCA) is generally recognized as the approved tool to achieve the purpose. The essence of LCA tool is to examine, identify and evaluate a kind of materials, product, process, or a system of environmental impact in their whole life cycle. The life cycle of materials or products includes whole process from raw materials obtained to the final disposal, or more ideal with original or other forms of the whole process of recycling [14-17]."

Jan 1, 2011

By T. C. Goel, A. Venna, R. G. Mendiratta

"Processing of ferrites has gained tremendous importance in recent times to meet the high performance demands on ferrites in keeping with the fast emerging· technologies. The quality of ferrite powders has strong influence on ·the performance of final device. Fabrication· of high performing ferrite components requires starting ferrite powders of precise stoichiometry, purity and microstructure. It is difficult to obtain these attributes by the conventional ceramic method. The key to obtaining quality powders lies in the· solution techniques. With this in view soft ferrites have been prepared by a wet chemical process, known as the citrate precursor method, which involves the formation of citrate complexes of the constituent cations. The advantages of this process are the ease of preparation and close control of composition, homogeneity, purity and particle size. Electrical and magnetic measurements on lithium ferrites have shown resistivity higher by more than two orders of magnitude compared to that observed for samples prepared by the conventional ceramic method, and low magnetic losses, making the ferrites specially suitable for high frequency applications.IntroductionProperties of ferrites are known to be sensitive to .their processing technique. A small deviation in the compositional stoichiometry of the ferrite affects its properties greatly. Soft ferrites such as Ni-Zn, Mn-Zn and Mg-Mn. are well known ferrites covering wide-ranging applications [1,2]. Lithiiim ferrites have also assumed technological importance for microwave applications and are potential substitutes for the expensive garnets [3]. Lithium ferrites are often doped with zinc to tailor the saturation magnetization required at high frequencies. Lithium and lithium-zinc ferrites, however, present difficulty to processing due to the volatile nature of both the cation components, namely Li and Zn. These ions are volatile at temperatures > 1000°C which makes their processing difficult. One of the main considerations of high frequency performance of ferrites is the high eddy current losses which prevent the interaction of the magnetic field with the ferrite component and hence impair device performance. These losses can be reduced by having a material of high resistivity. Electrical conductivity in lithium ferrite has been attributed to electron hopping [4] between the two vaience states of iron, Fe2+ <=> Fe3+, on octahedral sites. Maintaining the + 3 valence state of otahedral- Fe ions is thus a prerequisite for achieving high resistivity. The resistivity of ferrites is normally found to be low when processed by the conventional solid-state or the ceramic method [5]. This is attributed to (a) extensive ball-milling employed in the method to mix the component oxides results in non-stoichiometric compositions due to introduction of additional Fe ions on abrasion of steel balls during milling, (b) high processing temperatures involved which result in significant volatilization of Li and Zn ions creating thereby oxygen non-stoichiometry which results in reduction of Fe3 + to Fe2 +, (c) large and non-uniform grain sizes. In the present work, preparation of Li and Li-Zn ferrites by a non-conventional method known as a citrate precursor method [6, 7] which requires lower processing temperatures and duration is reported. The method gives stoichiometric compositions on account of homogeneous atomic-scale mixing of the constituent cations via the formation of metal-citrate complexes mixed in solution state. The method is also capable of giving small grain size which aids the oxidation ofFe2+ ions."

Jan 1, 2000

By D. F. Suarez

Spontaneous nodulation leading to growth of well developed glossy spheroids (generally hemispheres) of up to 0.06 cm width in 120 min has been observed during copper electrodeposition with certain levels of glue, thiourea and C1-. Thiourea alone can produce spontaneous nodulation but addition of glue and/or Cl- is required for rapid and sustained growth. In most cases once the glossy nodules develop they consume the majority of the copper deposited; thus, the specific current densities (and hence copper electrodeposition rates) on the glossy nodules are about an order of magnitude or, more greater than on the adjacent planar surfaces. The texture of the adjaoent planar surfaces is not glossy in appearance but is well faceted showing the usual deposition grain structure for such additives. Cathode potentials when spontaneous nodulation occurs are about TOO my more negative than with usual copper electroplating. This fact associated with evidence of extremely high levels of cathode surface passivation based on cyclic voltammograms indicates that the conditions which lead to spontaneous nodulation result from a very tightly adsorbed additive surface film. This film breaks down in specific points initiating the glossy nodules which then grow at extremely rapid rates. Current density is also important in spontaneous nodulation. At equal deposition times a current density of 21.5 mA/cm produced much larger glossy nodules than at 48 mA/cm2. The surface concentration of the glossy nodules was much greater in the latter case, however. The role of current density is still not well understood. The role of it as well as the relative roles of the three additives, thiourea, glue and Cl- in spontaneous nodulation is presented. Preliminary results and some possible correlations of these to help explain spontaneous nodulation are presented. It is believed that tankhouse upsets where cathode nodulation occurs may be related to this phenomenon.

Jan 1, 1987