Search Documents

By Ivan Imris

The iron production has generated many tonnes of very fine residues with high concentration of iron. In addition, during the recycling of galvanised steel scrap in the steel making processes the zinc and lead are largely concentrated in the dust. These kinds of dusts are usually dumped beside the metallurgical plants and cause environmental problems. Therefore the metal recovery from the metallurgical residues has become a major interest not only from the viewpoint of metals recycling but mainly from the viewpoint of environmental land protection. The thermodynamic analyses and laboratory experiments suggested that the metals could be recovered from metallurgical wastes by reduction roasting and by plasma smelting processes. The iron rich pellets with very high metallization may be obtained from metallurgical wastes by the reduction roasting and the inert slag and pig iron could be produced by plasma smelting processes. In both cases the iron rich products are suitable for the steel production. During the reduction roasting or plasma smelting the high volatile zinc and lead metals were removed and enriched as a secondary dust, Zn-Pb concentrate, which is suitable for processing in zinc and lead smelters. Suggested processes are commercially feasible and environmentally friendly without any solid or liquid waste.

Jan 1, 2003

By M. C. Ruiz

The conventional pyrometallurgical methods to treat copper sulfide concentrates include generally, one or more oxidizing steps where the formation of SO2 gas can not be prevented. From the economical point of view and the nature of some of the processes in which SO2 is produced, its complete capture is not feasible; therefore an important fraction is released to the atmosphere as fugitive emissions. In this research, the reduction of chalcocite was studied in the presence of lime as an alternative method, which overcomes the pollution problems related to SO2 emissions. The effect of temperature, time, concentration of carbon and CaO on the reduction rate were studied. Among these variables, temperature affects most the reduction rate. Conversions over 95 % can be obtained in less that 20 minutes at temperatures over 1000 ° C. The measured partial pressures of the gaseous components indicated that the chalcocite reduction proceeded through the gaseous intermediate species CO, C02, and the overall kinetics was controlled by the Boudouard reaction. The kinetic model In(1-X)= kt fits well the experimental data. Apparent activation energy of 3 14 kJ/mol was calculated for the temperature range of 900 0C-1050 °C.

Jan 1, 1999

By S. Vukcocic

A long term research project is in progress to establish the parameters of an acid leach process to recover alumina 'froui' high-iron and/or low-iron white bauxites, kaolinite, coal. ash and copper mine tailing. In this paper the results of acid leaching of copper flotation tailing for the removal of alumina are presented. The tailing is very complex material which contains 25% Al203 in the -10 lim fraction. X-ray diffraction indicates presence of quartz, kaolinite and minor 'alunite. After classification and ,separation of the -10 lim fraction, the raw material is fired to 550GC and leached at 90GC. Filtration is applied for the separation of white silicate residue form leach liquid. After the purification step, aluminum salt is crystallized from the solution, and calcined to alumina. Kinetic correlation and regime, of the processes are defined and presented in the paper.

Jan 1, 1992

By Joseph C. Rota

The Carlin Trend is one of the most significant gold mining districts in North America. Located in northeastern Nevada, a total of over 17 million ounces of gold have been produced since 1965 at Newmont Gold Company's open-pit and underground operations. Oxidized portions of the sediment-hosted, disseminated gold deposits at Carlin generally consist of finely disseminated concentrations of sub-micron sized native gold particles hosted in Paleozoic siliciclastic or carbonate rock. Oxide ore is commonly amenable to dump leach or heap leach processing, yielding an average 50 to 70% recovery of total contained gold. Refractory unoxidized ore requires some form of pretreatment oxidation to ensure economic gold recovery. Geologic ore control is typically combined with standard assay and engineering techniques to maintain both grade and metallurgical control ofleach grade ores. Mine geologists provide a vital function through field observation and recording ofmineralogic data during daily, visual blasthole logging. Intricately mixed refractory materials must be separated from oxide ore to ensure highest possible gold recoveries. Geologic information is combined with assay data to create mine polygons in an engineering computer database. Mining selectivity is further enhanced by in-pit ore control geologists who are available to make production decisions based on direct mineralogic observations at active mine faces.

Jan 1, 1997

By John A. Mavrogenes

Reflected light microscopy and electron microprobe techniques were used to determine the mineralogy, phase percentages, grain sizes, and textures of Co-Ni-rich mattes. The mattes were produced by submerged bath smelting at the University of Missouri-Rolla Pyrometallurgical Center of a flotation concentrate with 4.S% Co and 5.1% Ni that was prepared at the United States Bureau of Mines Rolla Research Center by flotation up-grading of the cobalt and nickel content of a copper concentrate from the Magmont mine, Viburnum Trend, Southeast Missouri. Nine distinct phases were distinguished in the matte samples, and three of these contain cobalt and nickel. The phases that were free from cobalt and nickel are bornite, chalcocite, pyrrhotite, magnetite, metallic copper, and galena. Submerged bath smelting serves to segregate the cobalt and nickel into phases that can subsequently be recovered by flotation. These phases are: shandite (Ni3PbZSZ)' cobaltpentlandite ((Co,Ni,Fe)9SS)' and Co-bearing Fe-rich sphalerite ((Zn,Fe,Co)S). Most of the cobalt occurs in cobaltpentlandite, but some is present in sphalerite. High total air conditions during smelting favor the development and segregation of cobalt into cobaltpentlandite. Nickel occurs in cobaltpentlandite and shandite. Shandite contains lead, a deleterious constituent in the smelting of cobalt and nickel.

Jan 1, 1989

By David M. Beckwith

Increased globalization and outsource manufacturing complicate the procurement and enforcement of intellectual property rights on a worldwide basis. Recent legislative and case law developments in the United States highlight the importance of a multinational intellectual property strategy. IP lawyers David Beckwith and John Hankins will discuss planning and pitfalls in this rapidly changing trans-border environment. Topics to be discussed include harmonization with international patent laws, protecting your technology and market space with a comprehensive approach to IP, and patent enforcement issues relating to import/export of products and components in the United States.

Jan 1, 2006

By Chang Chia -Fu

The generic structure of our bimesogens is shown in and for a typical blue-phase mixture of the type we describe here. We use mixtures of the ratio 33.4% (n =2.6), 34.1% (n =6.57), 36.6% (n= 11.15) with of the high twisted power (HTP) agent BD H1381(available from Merck Chemicals and described in ref. We then studied the electric-field dependency of the selective reflection in BP I* at 20.7 °C by applying increasing and the decreasing pulsed alternating current (a.c.) electric fields (100 Hz).

Jan 1, 2006

By J. R. Addison

Commissioned in September 1987, the Phelps Dodge Morenci, Inc. (PDMI) Central Electrowinning (EW) Tankhouse bas undergone two major expansions in its eleven-year history. A third tankhouse renovation, which began in November 1998, entails complete conversion of the 548-cell facility from a copper starter sheet based operation to Mt. Isa Process stainless steel mother blank technology. This paper outlines the operating history of the Central EW Tankhouse and reviews the conversion process, the rationale that led PDMI to undertake this project, and describes various design optimizations which have been implemented during the conversion.

Jan 1, 1999

By G. Ríos

Atlantic Copper Metallurgical Complex in Huelva (Spain) was commissioned in 1970 with a capacity of 40,000 tpy of copper from concentrate. In 1975 the old blast furnaces were replaced by the Outokumpu FSF technology. During the last 30 years, through several expansions and technical modifications, the production has increased up to 300,000 tpy of new copper. This paper describes the developments on the control of impurities that have been made to fit new situations, such as a new artificial gypsum plant, a new electrolyte treatment plant or different secondary materials handling management.

Jan 1, 2006

By Orlando C. Gaspar

The textures of the ores, the fine mineral intergrowths, the complex distribution of the deleterious minor elements, and the low base metal contents in some ore types, pose many technological problems to the beneficiation of the volcanogenic massive sulphides occurring in the Iberian Pyrite Belt. In particular fine intergrowths of the base metal sulphides with pyrite impose extremely fine liberation sizes (Kao=15 to 25um). The mineralogical, textural and metallogenic studies have provided an understanding of the distribution of vertical and lateral metal zoning in the ore bodies. Mapping of the ore types, carried out by mine geologists, and the metal zoning patterns computed from data base have shown that ore types are distributed as ore lenses, and that vertical and lateral base metal zoning exists in several orebodies. Since ore processing efficiency is affected by ore textures, and because the same mineral often shows different textural features, a relationship between the textures of the feed ores and those of the middlings must be established for all ore types defined at the deposit scale. For supplying, on time, the information needed for the optimization of the concentration processes, empirical methods of determining the mineralogical and textural characteristics of the several ore types have been developed.

Jan 1, 1995

By Lucas Lopes da Costa

Bamboo fibers were characterized in terms of diameter distribution and tensile properties. Polyester matrix composites reinforced with these fibers were investigated for their flexural mechanical behavior. Specimens with up to 30% in volume of continuous and aligned bamboo fiber composites were bend-tested until fracture. The results showed an improvement in the composite strength and stiffness with the amount of bamboo fiber. A microstructure analysis by scanning electron microscopy revealed a reasonable adhesion between the fiber and the polyester matrix which justifies the improved mechanical properties of the composites.

Jan 1, 2010

By Jürgen Antrekowitsch, Thomas Griessacher

The recovery of valuable metals from residues like dusts and sludges is nowadays state of the art. Depending on the complex constitution, a recovery of different metals can – in the majority of cases – only be performed with considerable energy input in high temperature processes together with insufficient yields and newly generated residues. Often, the behavior of the dust or sludge in the process during melting or reduction is unknown. In this work, a detailed characterization of selected residues like steel mill filter dusts, cupola furnace dusts and leaching residues is done. The different steps of getting from solid particles into a homogenous liquid phase were investigated. Although high temperature processing leads to high reaction speeds, the complexity of residues keeps the system away from thermodynamic equilibrium. With this research program, some basics are generated to understand smelting and reduction and the gap between thermodynamical calculations and real behavior can be explained.

Jan 1, 2008

By J. Michael Canty

Over 25 years of US research in Mineral Recovery from Geothermal Solutions have lead to few commercial applications. With the World Bank program in Kamchatka, Russia in September 2005 a step was taken to vitalize and coordinate the many efforts to advance economic mineral recovery systems worldwide. The US Department of Energy is helping to spur on the interest and research needed to realize the many benefits of extracting minerals from geothermal solutions. The excitement of recovery of minerals from geothermal brines has many positive angles. The economics of certain geothermal site is improved if a revenue is arrived from a sellable commodity with the geothermal power. The use of cleaner geothermal brines also improves the capable use of the brine before reinjection. We will review the history of Geothermal in the USA and the opportunities for recovery of different minerals and the markets for them.

Jan 1, 2006

Convential smelting of copper - cobalt - iron sulphide concentrates result in th eoxidation of cobalt and iron, which are subsequently lost into the slag. The emission of SO2 bearing gas from smelting causes serious health and environmentsl problems. In this investigation, three different types of copper - cobalt - iron sulphide concentrates, derived from froth flotation, were investigated, the concentrates, each containing more than 40 wt % percent gangue material, were directly reduced in the presence of lime and corbonin the temperature rnage of 1073 K - 1573 K, fo rthe production of an alloy containing copper, cobalt and iron. We demonstrate the basic principles of process physical chemistry for the recovery of alloy by carrying out a detailed process analysis utilising the predictions from thermodynamic equilibrium and results from the kinetics of reduction reaction. The effect of temperature on the reduction kinetics and alloy formation were determinedand analyzed in detail.

Jan 1, 2012

By F. Tailoka

In order to decrease the voltage required for electrorefining, a recessed electrode cell has been developed in which the anode and cathode have recesses machined into their faces. The anode and cathode plates are separated by a thin refractory cloth and the cell is filled with fused salt. Bismuth containing 10 to 90 % lead with copper and silver as minor impurities has been electrorefmed at a current density of 10,000 to 20,000 Am-2. The cell voltage was between 285 and 635 millivolts and the bismuth was refined to a purity of 99.9 %. Flow patterns were observed in a room temperature model of the recessed channel cell using water and mercury to simulate molten metal and the fused salt electrolyte. The flow in the electrode recesses is characterized by discrete droplets when the liquid flow rate is low and thin streams and rivulets at higher flow rates.

Jan 1, 1995

By Javier Antoñanzas, Juan Carlos Múgica, Lourdes Yurramendi

The gasification of wastes containing an organic fraction is usually performed at low-medium temperature using different kind of catalysts. The off gas obtained is a mixture of carbon oxides, mainly carbon monoxide, and hydrogen and can be used for different energetic applications. The main problem is the production of tars in the off gas that has to be separated from the valuable gas flow and, finally, treated separately. An interesting alternative is the partial or total treatment of organics at high temperature. In this case, the off gas contains a higher content of hydrogen and elemental carbon as particulate matter. The energetic source to obtain a temperature in the range of 1,000 - 1,200 ºC is obtained by a plasma torch. In order to make de process attractive, an important issue to be considered is to commercialize the carbon obtained for different industrial applications.

Jan 1, 2008

By Kejun Liu

Platinum and palladium are usually dissolved together and followed by separation. In this study, the selective leaching of platinum and palladium from a secondary resource, such as dental waste, by using chloride solution (hypochlorite and chlorate) has been developed. Results indicate that about 100% of palladium could be initially extracted by the combination of 0.3 mol/L sodium hypochlorite (NaClO) and 0.068 mol/L sodium chloride (NaCl) at pH 1.2 and 298K in 1.5 hours, or the combination of 0.005 mol/L sodium chlorate (NaClO3) and 6 mol/L hydrochloric acid (HCl) at 298K in 0.5 hour. About 100% of platinum could be extracted from the residue by the combination of 0.47 mol/L sodium chlorate (NaClO3) and 12 mol/L hydrochloric acid (HCl) at 298K in 2 hours.

Jan 1, 2003

By Lætitia H. Delmau

SXFIT is the latest in a series of programs developed in our group to model solvent extraction systems of increasing complexity. SXFIT permits the user complete freedom to define the constituents from which the composition of each phase is to be specified in the data and from which all species of a model for a system are assumed to be formed. Activity coefficients in the nonaqueous and aqueous phases, water activity, apparent molar volumes of aqueous species, and solution density needed for the conversion of concentration from the molarity to the molarity scale are all taken into account by the program. Several extraction systems relevant to nuclear-waste treatment were modeled successfully using this program. As an example, the cesium extraction efficiency of the CSSX process chosen by the USDOE for cesium removal from high-level waste stored at the Savannah River Site can be predicted correctly for varying feed composition.

Jan 1, 2003

By Jung-Ah Kim

Precipitated Calcium Carbonate (PCC) is obtained through calcination, hydration, and carbonation. Thus, the change in each process condition determines the particle size or morphology of PCC. To date, studies on precipitated calcium carbonate have mainly focused on process manufacturing PCC, aimed matter. Still, few studies on calcination or hydration have been conducted. Therefore, this study sought to investigate the effect of hydration condition on the synthesis characteristics of aragonite PCC. Results showed that the particle size of calcium hydroxide changed based on the variation of the initial hydration temperature. In particular, higher initial temperature resulted in the larger particle size of calcium hydroxide used in synthesis. The particle size and yield of aragonite also increased when calcium hydroxide made at high temperature was used. The water/solid ratio or total amount at the hydration time had no effect on the manufacturing process of aragonite, however.

Jan 1, 2006

By Sung-Mo Jung

Experiments were carried out on a system with artificially prepared slags in a graphite crucible, in order to examine the possibility of recycling BOF slags produced in the steelmaking process. More than 80% of FeO and P2O5 was reduced within 20 minutes and the FeO reduction rate was greater than that of P2O5. P2O5 reduction began after more than 60% of FeO was reduced. Increasing slag basicity enhanced the reduction of FeO and P2O5. Temperature also improved slag reduction. The overall reduction rate was controlled by the chemical reaction at the slag/carbon interface. The reduction rates of FeO and P2O5 were second and first order with respect to their respective contents. Most of the reduced phosphorous is believed to vaporize in the form of P2 gas.

Jan 1, 2006