Search Documents

By Asmo Vartiainen

The viscosity of liquid Fe-O-SiO2 -slag at copper smelting conditions was investigated using a rotational viscometer. The studied parameters were oxygen partial pressure (10" °-10"6 bar ); composition of slag (Fe/SiO2 ratio), and temperature (1250-1400°C). The viscosity values are presented as a function of Fe/SiO2 ratio and as isoviscosity curves in ternary FeO-Fe2O3-SiO2 diagrams. The increase in viscosity at high silica contents can be accounted for the polymerisation effect of SiO4/4- -anions. At high ferric iron contents, higher oxygen partial pressure, the viscosity values increase especially near the magnetite saturation. The viscosity values are highest at the double saturation of silica and magnetite. At lower silica and ferric iron contents the viscosity values are more uniform in the homogenous liquid slag area. The viscosity values were lowest at high temperatures and highest at low temperatures.

Jan 1, 1998

By Peter Hayes, Evgueni Jak, Ata Fallah Mehrjardi

Modern analytical tools, such as electron probe X-ray microanalysis (EPMA), are used in experimental characterization of phase equilibria and microstructures of complex slags. Integrated thermodynamic computer packages, such as FactSage, are used to provide more accurate descriptions of complex slag systems. These advanced methodologies have been applied to characterize dynamic steady state freeze linings in slag systems using submerged cold finger probes at controlled laboratory conditions, establishing the effects of bath chemistry, temperature, heat extraction rate and bulk fluid flow. It has been found that stationary freeze lining deposit interface temperatures at steady state conditions can be lower than the bulk slag liquidus temperature, and that stable operation below the liquidus is possible. A conceptual framework has been developed to explain the phenomenon and the range of interface temperatures that can be obtained in dynamic steady state conditions. These findings have important implications for the design of freeze linings and possible improvements to high-temperature metallurgical operations.

Jan 1, 2014

By cheng Peng-fei, TANG Hai-yan, guo Xiao-chen, LI Jing-she, Liang Yong-cang, Zhao Baojun

The origin and evolution of non-metallic inclusions for Al-killed casing steel during EAF-LFVD- CC process were studied by industrial tracer experiments. The formations of Al2O3 and MgO·Al2O3 micro- and macro-inclusions from ladle slag were analyzed by theoretical calculations. The results show that micro-inclusions were formed during deoxidation and temperature decreasing in the process of casting, most of the macro-inclusions come from entrapped ladle and mold slags. In addition, most of the Al2O3 formed were modified into 12CaO·7Al2O3 and 3CaO·Al2O3 inclusions which are liquid at steelmaking temperature. MnS cannot be fully modified to CaS and it was only wrapped outside the alumina or calcium aluminate in the form of (Ca,Mn)S with the amount of Ca-Si wire fed during the test.

Jan 1, 2016

By Yong-ming Chen, Chao-bo Tang, Yun Li, Long-gang Ye, Sheng-hai Yang, Hao-tian Xue

In order to achieve high recovery of Cu and Co during cobalt-bearing copper sulphide ore smelting process, reducing agent (coke) and sulphidizing agent (pyrite) were added into molten smelter slag for reducing-sulphidizing smelting to product Cu-Co matte. Effects of reductive atmosphere, pyrite dosage, smelting temperature and smelting duration on Cu, Co, Fe distribution behaviours were investigated. The results show that the distributions of Cu and Co are mainly enriched in Cu-Co matte, and the distribution ratio, LCu and LCo, improve with increasing of coke amount or pyrite addition, whereas above 6 wt.% coke or 20 wt.% pyrite, Cu and Co tend to transfer from matte to cleaned slag. A properly high temperature(1300) and smelting duration(3h) are beneficial to the enhancement of the distribution ratio of valuable metals, and under the given set of conditions, LCu > LCo generally. However, an undesired high Fe contents in matte limit further increase of LCu and LCo.

Jan 1, 2015

By Elli Miettinen

In Copper Flash Smelting operation disturbances may lead into dust build-up in the gas train and off-gas handling system causing reduced heat recovery efficiency and process availability. Flue dust of a Copper Flash Smelting process heat recovery boiler has been characterized and its thermal conductivity and diffusivity have been determined. Dust accretions consist of several layers possessing varying particle sizes, densities, and thermal properties, with the binding phase usually being sulphate. All the dusts can be regarded as effective thermal insulators with thermal conductivity values of less than 2 W/mK and thermal diffusivity values of less than 0.005 cm2/s. Porosity can be regarded as a fairly good indicator of the thermal transport efficiency of these types of materials, but the material microstructure must also be considered. The results can be used in the dimensioning of metallurgical heat recovery boilers and they also provide accurate input data for process models.

Jan 1, 2009

By Frank M. Kimmerle

Spent Potlining (SPL) contains recoverable chemical elements (C, F, Na and Al) which are lost in stabilization or immobilization processes primarily aimed at eliminating cyanides and reducing leach rates of soluble fluorides prior to landfiling. They can be recovered in a variety of mineral forms for recycling in the aluminum industry and elsewhere. Alcan has developed a cost-effective hydrometallurgical route, combining a number of proven unit processes to destroy cyanides, recycle the chemical values and provide a zero-discharge process. Pilot plant studies of this Low Caustic Leach and Liming (LCL&L) Process prove that the fluoride scan be converted to acid grade fluorspar, while the sodium and aluminum are recovered as a sodium aluminate and caustic feed to the Bayer Plant operations. The remaining brick and carbon fraction constitutes a high ash solid fuel which meets TCLP leach criteria and whose reduced sodium content enhances its value as a chemical reducing agent.

Jan 1, 1994

By Steven Wright

The reduction of a slag produced 6om the recycling of lead batteries was studied in a kilogram scale laboratory investigation by reacting with graphite at temperatures of 1180 and 1200°C. Simultaneous reduction of PbO, Fe203, Sb203 and As203 occurred with the Sb and As reporting to the metal while the lead content in the slag was above 2 wt%. The Sb and As distributions between metal and slag were strongly affected by temperature and slag oxidation state. The rates of reduction of PbO and Sb203 increased with increasing slag basicity and temperature and decreased as the PbO content in the slag decreased. The reduction rate of PbO from these slags was similar to other industrial lead slags at the same CaO/SiO2 ratio and temperature. The implications of the behavioural similarities of the antimonous slags during reduction with carbonaceous reductants and other lead slags are briefly discussed.

Jan 1, 1994

By Mark Jolly

"Over the last ten years or so many man hours have been dedicated to developing methods for simulating shape casting processes. The majority of the methods developed have been devised by a combination of computer, mathematics and materials specialists often with limited knowledge of foundries and foundrymen. As a result of this it would appear that although there are many software packages for the foundryman to use there still exist fundamental misunderstandings as to their usefulness and suitability within the foundry.The paper aims to identify how well current software packages perform. The relationships between physical phenomena, practical defects and software capabilities are presented. Some discussion of the use of criteria functions is also presented. Finally issues arising from the postprocessing of results are discussed as the presentation of the results to the lay-person in simulation techniques is possibly one of the most important aspects in influencing the adoption of this type of software in the foundry community."

Jan 1, 1999

By Zhen Zhang, Jiang Diao, Xuan Liu, Tao Zhang, Bing Xie, Hong-Yi Li

Extracting vanadium from vanadium containing hot metal by LD process has been proven an effective solution for the utilization of vanadium-titanium magnetite ore, but the systematic analyses of vanadium extraction rate and mechanism by basic slag are seldom reported. In this study, mathematical model of vanadium transfer from metal to slag was formulated and the rates of vanadium extraction of hot metal with basic slag were investigated. The results indicated that the apparent vanadium extraction rate constant, kp, were in the range of 1.33~9.07×10-4g/(cm3·s). And the rate constant was increased with the increase of final slag basicity, reaction temperature and stirring gas flow. The apparent of mass transfer parameter decreases significantly from 0.13 cm3/ s to 0 cm3/ s in 20min, and the data changed as negative due to the decrease of slag oxidation and recovery of vanadium from slag to metal.

Jan 1, 2015

By Pan Cao

The process of reduction roasting of nickel laterite with rotary hearth furnace combined with magnetic separation becomes a very potential way to prepare ferronickel alloy, especially for the low grade nickel laterite ore. In order to realize this new process, the effect of roasting temperature, time and additive on the reduction degree were investigated in the laboratory experimental. The results indicated that the recovery rate of Ni increased with the roasting temperature increasing to 1500°. Most of nickel and a spot of iron are selectively reduced with adding 25.19% SiO2, 6.42% coal, and roasting for 60min at 1500℃. Then conventional magnetic separation was carried out. The content of Ni and Fe are 7.50% and 59.08% in ferro-nickel nugget prepared by this method. And the recovery rate of Ni is 90.91%, which indicates that a high recovery of ferro-nickel from nickel laterite ore is achieved indeed.

Jan 1, 2014

By Sadi Medina

As it is characteristic from Custom Smelters, ENAMl Las Ventanas Smelter has to deal with different qualities and quantities of mining products from about 70 suppliers, that contain a variety of impurities that would be harmful for copper production. In order to increase the smelting capacity, an oxygen plant has been running since September of 1990. Moreover, to improve the environmental conditions, a new sulphuric acid plant started up to neutralize the metallurgycal off-gases from the Teniente Converter and partially from the Peirce-Smith converters. Based on the on-line operation among the reverberatory furnace and the Teniente Converter using oxygen enriched air to produce high grade matte, most of the volatilizing impurities, mainly arsenic, are collected as discarding compounds in the gas cleaning system of the acid plant. This paper describes the continuous performance of the Teniente Converter with acid plant, the results attained, the operation problems and how they were solved. The impurities distribution achieved in this process is also included.

Jan 1, 1993

By R. K. F. Lam

Unacceptable levels of impurity were noted in high purity chromium melting. Analysis of recent melting data determined that oxygen content in chromium is the critical parameter. Thermodynamics studies identify zirconia to be the most stable oxide in the presence of liquid chromium, followed by alumina and silica. Iron oxide reacts readily with liquid Cr. A certain degree of chemical reaction between liquid chromium and oxides does occur, contamination by the crucible is therefore unavoidable. Equilibrium constants indicate that a chromium oxide addition decreases 'ceramic dissolution and reduces impurity contamination. Safe operating conditions with oxygen content between 1190 ppm and 2500 ppm were identified. Additions of chromium oxide (Cr2O3) of 161 grams and 264 grams to liquid chromium yielded acceptable levels of impurity, and oxygen content was respectively increased to 1624 ppm and 2 179 ppm. A new process of melting high purity chromium with chromium oxide addition for controlling the activity of Cr2O3 is recommended.

Jan 1, 1997

By Stein Tore Johansen

The flow of a liquid through a large grain filter has been considered. An improved form of the fluid dynamic equations describing flows through porous media is proposed. The theory is applicable to all Reynolds numbers. Particulate inclusions are described by passive scalar fields where only very simple mechanisms for particle removal are included. However, the deposition of particles are allowed to change the "porosity" of the filter. Hence, the flow pattern through the filter will change as the filter ages. The theory is employed to the filtration of aluminum in an industrial grain filter. The model shows that the filter is not effectively designed and there is room for considerable improvement. The dynamic "aging" process of the filter is shown to change the filtration from bed filtration to cake filtration. Finally, the predicted inclusion collection efficiencies are compared to efficiencies measured in an industrial filter. The predicted initial efficiencies are in very good agreement with experimental results.

Jan 1, 1990

By Huanmei Yuan, Yuanyuan Wang, Hao Bai

Composite phase change materials are widely used in energy-saving and energy efficient process. Nano-encapsulated phase change materials are especially significant for making advanced working fluid applicable to waste heat recovery or storage. In this study, silica-coated stearic acid (SA) Nano composite phase change materials were prepared from tetraethyl orthosilicate (TEOS) and stearic acid (SA) via sol-gel process. The materials were investigated by Field emission scanning electron microscopy (FE-SEM), Transmission electron microscope (TEM), Fourier transform infrared spectroscopy(FT-IR) and Differential scanning calorimeter (DSC).The FE-SEM and TEM results show that monodisperse microspheres with stable core– shell structure were formed and SA was encapsulated in the silicon dioxide shell. The FT-IR results show that there were no chemical reaction between silicon dioxide and SA, which is the chemical property of the composite material, is stable. The DSC results show that the composite phase change material has favorable heat capacity.

Jan 1, 2016

By Gerardo Fuentes

The stoichiometry and kinetics of the hydrothermal reaction of enargite in copper sulphate solutions was investigated in the range 140–300 °C, and particle size under 15 and 50 μm. The stoichiometric experiment was performed at 300 °C, using one gram of sample (96% enargite, 4% tennantite) and 100 mL of copper sulphate solution (10 gpl) at 1.2 pH. Enargite reacted completely after 80 min. A solid product was obtained and characterized by XRD. The main product was chalcocite (M) and some traces of djurleite and chalcocite (Q). Tennantite did not react under these conditions. The kinetic experiments were conducted at 140 °C, 190 °C, 250 °C and 300 °C. From fitted data and Arrhenius equation the calculated activation energy (Ea) was 51 kJ/mol. According to the hydrothermal transformations studied, the reactivity of different phases found in the copper concentrates was bornite > chalcopyrite > covellite > sphalerite > pyrite > enargite > tennantite.

By R. G. Reddy

The effect of solid particles on viscosity behavior of Na2O-O-B2O3-SiO2 melts of composition XSio2/XNa2o =0.5 and in the temperature range of 900- 1150 K was studied. Samples were analyzed by X-ray diffraction and optical microscopy. The results showed that a crystalline phase (NaBO2) was formed and its amount increases with decrease in X,, from 0.50 to 0.25. The experimental viscosity values were compared with the predicted values using our viscosity model developed earlier. At low temperatures, for low content of B2O3 , the experimental values exhibits a large deviation from the predicted values. It was concluded that the deviation was due to the formation of solid particles in the molten slags. The existence of these solid particles increased the viscosity values significantly. A new viscosity model was developed to include the effect of solid particles.

Jan 1, 1993

By Zhang Yongzhu

The metallogeneticy and mineralogy of three types of Chinese refractory gold deposits (Au-As; Au-As-MeS; Au-As-C) which are somewhat different from those abroad are discussed. The modes of occurrence, the distribution of grain size, and the morphological features of gold in minerals and their influences on gold recovery by direct cyanidation are also discussed. According to the mineralogy of gold and minerals, bacterial leaching, pressure leaching and roasting technology are suitable for the pretreatment of arsenopyrite-Au, pyrite-Au and carbonaceous-clay-Au refractory gold ores prior to cyanidation, respectively. The most important sulfide pyrite bearing much gold is difficult to be oxidized, its crystalline structure, conduct-types , and minor elements in different mineralizing stages are also discussed. The pyrite aggregates in different deposits are very complicated and much different. Gold grade of arsenopyrite is much higher than that of pyrite for some deposits which have a high correlation coefficient of Au vs As.

Jan 1, 1992

By T. Tamagawa

Vaporization of zinc and mixing of zinc vapor with CO-CO2 mixtures were studied experimentally to prepare Zn(g)-CO-CO2-Ar mixtures with desired composition for investigating the condensation behavior and efficiency of zinc vapor. The vaporization rate of zinc was generally constant under given conditions, and could be increased by raising the flow rate of the carrier gas, temperature and vaporization area. The Zn(g)-CO-CO,,-Ar mixtures were quenched by a water-cooling sampling tube for measuring the actual composition of the mixtures in the reactor. The oxidation extent of the zinc vapor in the CO-CO2 mixtures had relation to the CO2/CO ratios and the temperatures. Under current conditions, it was necessary to employ the CO2/CO ratio below 0.125 for mixing the zinc vapor with CO-CO2 mixtures without oxidation. In addition, the appearances and zinc contents of the condensed zinc on the sampling tube were also examined.

Jan 1, 2001

By Petrus Christiaan Pistorius, Ming Tang

Magnetite concentrate is pelletized and then hardened by elevated-temperature oxidation to hematite, to produce pellets for ironmaking. Previous work showed that the rate of oxidation is under mixed control of gaseous mass transfer of molecular oxygen through the pellet pores, and solid-state diffusion into the oxidizing grains. Because of the partially limiting role of solid-state diffusion, concentrate size distribution strongly affects pellet oxidation. Previously, a simple mixed-control model was formulated to describe isothermal oxidation. In that model, the main effect of concentrate size distribution was on the plateau level of oxidation which is reached at a given temperature. However, the extent of plateau oxidation increases with increased temperature, requiring a more complex model for non-isothermal oxidation. In this paper, predictions of the non-isothermal model confirm the strong effects of concentrate size distribution and oxygen enrichment. In particular, a greater fraction of coarse magnetite particles would be beneficial, decreasing the size of the macroscopic unoxidized pellet core.

Jan 1, 2015

By Jiangtao Li, Zhongwei Zhao, Xingyu Chen, Xuheng Liu

In order to produce good quality ammonium paratungstate, Sn needs be removed efficiently from the tungstate processing solution. The nascent hydrous ferric oxide has excellent adsorption ability and is often used as an adsorbent to remove metal ions from aqueous solution. In this paper, nascent hydrous ferric oxide is used to remove Sn from tungstate solution. Through experimental, the effects of pH value, reagent amount of adsorbent, reaction temperature and reaction time on the Sn removal are investigated. The study shows that 98% of Sn can be removed effectively from sodium tungstate solution and only 2% of W is lost during process under the conditions of pH 9~12, reagent amount of Fe addition 40 times Sn amount, reaction time 30min and room temperature. As the Fe addition reaches 90 times of Sn concentration in the ammonium tungstate solution, 99% of Sn is removed and APT with zero level purity national standard is obtained.

Jan 1, 2014