Search Documents

By T. Shoji

"The human history is characterized by social development based on mineral and energy resources, and many conflicts to take the resources by power. This is shown by not only world wars but also many local conflicts as well as international supremacy.IntroductionThe world population after B. C. 10000, which is summarized in several papers, is approximated by four straight lines on a semilogarithmic diagram as shown in Figure 1 [l]. The annual rates of increasing are 0.0041, 0.071, 0.53, and 1.85 % from the old and young periods. The boundaries among four periods are approximately B. C. 4600, AD. 1670, and 1930. The start of the second period seems to correspond to the beginning of agriculture and cattle breeding. Precisely speaking, the usage of natural energy resources such as woods and domestic animals already began, but is inferred to have become common after the age. The third and fourth periods are characterized by the common usage of coal and oil, respectivety. Not only energy resources but also mineral resources including gold, copper, iron and others are also important for the human history.Mineral and energy resources have supported the development of the .human civilization, and have caused many conflicts because of this reason. Every day newspapers report conflicts, such as Chechnya, East Timor and Ache. We can easily point out the facts that the conflicts closely relate to mineral and energy resources. Groznyj, Capital of Chechnya, is located on the western margin of Caspian oil field. Many mineral deposits occur in Kavkaz Mountains running south of Chechnya. Subsea oil fields occur in Timor Gap located between East Timor and Australia. Ache is also one of oil fields in Indonesia. It is very difficult to state present conflicts independently of a political view of point. For this reason let us try to historically review the relation between mineral and energy resources and international domination and conflicts [2] based on many papers [3]."

Jan 1, 2000

By Lev Levin, Sergei Lesokhin

"The formation of titanium carbide during hot filament assisted carburizing of NiTi alloy was investigated. Phase content and morphology of the diffusion zone were examined by X-ray diffraction, X-ray microanalysis, SEM, and Auger electron spectroscopy. The growth of stable and adherent TiC film was observed. A non-planarity of interphase boundary was noticed. The applicability of the chemical diffusion approach to the analysis of the experimentally observed interface instability is discussed. A criterion, taking into account the influence of growth stresses on the stability of the flat interface, is developed by means of linear perturbation analysis.Introduction.Equiatomic intermetallic NiTi belongs to a class of materials exhibiting the shape-memory effect. The unusual property of this compound promotes its application in many fields, from aerospace technologies to medicine. The relatively high ductility ofNiTi also permits its use as a matrix material in metal-ceramic composites. The objective of this work was to investigate the possible incorporation of a ceramic material (titanium carbide) into NiTi by gas carburizing.Free energy calculations indicate the potential to obtain TiC by carburizing Ni-Ti binary phases. The main obstacle to such a process is the high affinity of titanium to oxygen. At moderate temperatures the formation of TiC is preferable to titanium oxidation only if the partial pressure of oxygen is extremely low [1]. This problem was overcome in this work by the use of hot filament assisted gas carburizing. Due to chemical reactions occurring near the hot filament, the gas mixture, initially consisting of methane and molecular hydrogen, was enriched by atomic hydrogen [2], drastically decreasing the content of free oxygen in the carburizing atmosphere.The second part of this article concerns the theoretical analysis of reasons that lead to the development of the experimentally observed morphology of the diffusion zone. In particular, the influence of the growth stresses on the morphology of an interphase boundary is investigated."

Jan 1, 1996

By Cindy L. Williams

"The Blue Star subdistrict in the Carlin Trend, Nevada, includes multiple mines with 33.9 t Au in reserve and past production totaling 89 .1 t Au. The deposits are characterized by zoned alteration mineralogy and gold grades. From orebody centers outward the zones include: 1) a silicified core with erratic gold grade; 2) adjacent mill-grade (> 1.37 Au git) intense quartz-sericite-pyrite alteration; 3) enveloping leach-grade (0.21 Au g/t to 1.37 Au git) weaker sericite-kaolinite-quartzpyrite alteration; 4) surrounding decarbonatized and intensely argillized waste and leach grade ore; 5) pervasively decarbonatized waste rock; and 6) peripheral waste with weak decarbonatization and local propylitic alteration. Zoned alteration extends as much as 1500 m beyond orebodies.Understanding Blue Star subdistrict zoned alteration assemblages and gold grades has increased geologists' ability to provide practical and economically significant information to geotechnical engineers, mine planners and drill and blast personnel. Alteration influences geotechnical pitslope design because each assemblage has distinct rock strength. Geotechnical engineers use three-dimensional models of incompetent alteration types as a foundation for pit-slope design. In the drill and blast cycle, hard and soft alteration types require modified practices (powder column, blast hole spacing, delay design etc.) for optimum blast energy distribution. Further, geotechnically instable alteration types require careful blast procedures to prevent backbreak whic~ damages ultimate walls. In addition to mine planning and mining applications, zoned alteration assemblages extending beyond orebodies provide a useful exploration guide. Metallurgical character also varies with alteration type. Intensely quartz-sericite-pyrite altered or silicified ore has relatively high partical-size dependency and poor leach recoveries. Moderately sericite-kaolinite-quartz-pyrite altered rock, in contrast, shows little size dependency and good leach recoveries.The author sincerely thanks L. Schutz, P. Williams, C. Clode, W. Trudell, P. Herrera, M.DKunkel, M. Goings and numerous other Newmont geologists, metallurgist, engineers and support staff who made this paper possible."

Jan 1, 1997

By Marcela C. Santini, Luiz A. Teixeira

"Surface conditioning (also referred as etching) of plastics prior to metallization is generally conducted with sulfuric I chromic acid solutions. Although these baths perform well technically, the presence of Cr (VI) imposes serious operating problems of an environmental nature. The present work reports ·the results of a study of surface conditioning o(ABS using solutions based. on sulfuric acid, with hydrogen peroxide and/or nitric acid, replacing chromic acid, as oxidants. Process performance was evaluated by SEM and by the uniformity and adherence of electroless nickel coatings applied on selected conditioned samples. The results showed that the evaluated types of solutions could be optimized to perform as well as the chromic-based baths, with a much superior environmental quality.IntroductionMetallization of plastics is normally undertaken for either decorative or functional purposes. Through metallization, the specific properties of plastics such as light weight, design flexibility, and low-cost of manufacturing are enhanced by the addition of properties usually associated with metals. These include reflectiveness, abrasion resistance, electrical conductivity, and a variety of decorative effects (1).The available processes that can be used for metallization of plastics are vacuum metallization or vapoµr deposition; indirect metallization and plating (1). Plating can be sub-divided into electroless plating and electroplating. In electroless plating, metal ions in aqueous solution are deposited on the .activated plastic surface by oxi-reduction reactions without the aid of an external electric potential, forming a thin metallic layer. This electroless deposited film has two functions: (a) it provides an electrically conductive substrate that allows further coating by electroplating; and (b) provides a secure bond between the plastic substrate and the electroplated layer (1,2). In case the electroless metallic part requires an additional layer for finishing purposes, or just an increase in thickness, the part can be additionally electroplated with a· variety of metals - in most cases those are copper, nickel or chromium (3)."

Jan 1, 2000

By Marta Cabral, C. A. Nogueira, F. Margarido

"Physical processing of spent batteries which includes shredding and sieving operation is the first step for chemical treatment by hydrometallurgy. A laboratory study was carried out to evaluate physical processing efficiency, by analysing the resulting particle size, of alkaline and saline mignon-type Zn-MnO2 batteries. After shredding with a tip shredder, results obtained showed that alkaline batteries were more efficiently size reduced than saline batteries. Difference in particle size distribution was larger for granulometric fraction -20+11.2 mm and also higher for saline batteries. Average diameters (d50) for saline and alkaline batteries were respectively 9.1 and 6.2 mm. Chemical composition carried out on several granulometric fractions allowed to identify metals distribution through size categories. This analysis showed that zinc concentration with the grain size was almost constant, while manganese decreased when particle size increased. More than 95% of iron scarp from the battery cases had a particle size higher than 5.6 mm.IntroductionRecycling process of spent batteries includes physical unit operations which involves a fragmentation step in order to open the battery cases and to allow the access of chemical reactants to the electrode materials, on further chemical unit operations. Shredders are usually used for that purpose, using cutting mechanisms and allowing efficient fracture of residues in order to promote further processing of the contained materials. Batteries are complex products with a large variety of sizes and shapes which causes serious difficulties for predicting and carrying out its fragmentation.Domestic-type batteries are essentially of the Zn-Mn systems and with cylindrical shape, varying from the large size Mono (or D) type to the small size Micro (or AAA) type [1]. Recycling of batteries involves collection, sorting [2] and metallurgical processing [3, 4]. In some processes, the first step of metallurgical processing is dismantling and size reduction by shredding. Research work on spent batteries considering grinding/shredding and physical separation of fractions is scarce [5-7], but investigation in this domain is very necessary."

Jan 1, 2008

By Chang Wei, Zhigan Deng, Jiqiang Liao, Minting Li, Hongsheng Xu, Yan Song, Cunxiong Li, Xingbin Li

"Abstract: Direct ?otation of oxidized zinc-lead ore is characterized by recovery of zinc and lead only around 55% and 50%, respectively. Mineralogical analysis shows that the sample used in the present study is a carbonate hosted zinc-lead ore, with a zinc and lead carbonate content that accounts for 80.14% and 75.63% of the total minerals, respectively. The carbonate hosted zinc-lead ore was hydrothermally sulfidized with elemental sufur and the experimental data indicated that under the conditions employed up to 75% zinc and 82% lead sulfidation extent were achieved. As a result of pre-sulfidation followed by flotation, the recoveries of zinc and lead into flotation concentrate were over 90%. A flotation concentrate was obtained with 52% Zn and 37% Pb from the materials which was treated by sulfidation.IntroductionSulfide ores are the primary source of zinc and lead, and they are becoming depleted; thus, metallurgical investigators are interested in using abundant oxidized zinc-lead ore reserves. The high-grade zinc-lead oxidized ore, which normally has a zinc content higher than 15%, can be disposed of by acid leaching and electrolysis. However, the low-grade ore, which has a zinc content lower than 10%, is difficult to smelt with pyrometallurgy and hydrometallurgy, and the processes are very complicated and expensive in terms of production flow and energy consumption. Therefore, making the low-grade oxidized zinc-lead ore more beneficial has become more important in recent years. Flotation is the most common process, and the primary method of recovering zinc and lead from sulfide or oxide minerals. It is well known that there is a difference between sulfurized and oxidized minerals regarding their separation by flotation. Flotation of zinc and lead oxidized minerals is extremely complex because of the similarities in the physicochemical and surface chemistry of the constituent minerals. There are no known direct-acting collectors capable of producing single metal concentrates [1-3]."

Jan 1, 2012

By Robert W. Bartlett, Keith A. Prisbrey

"Natural biooxidation of shallow, refractory ore heaps, relying on gaseous oxygen diffusion from the heap surface is attractive because of its simplicity and potential low cost, especially without using a lined pad, which is possible if percolation of leachate through the heap is avoided. In this case, the excess oxidation enthalpy must be removed by water evaporation from within the wet ore heap, and the rising water vapor flux within it will impede the downward oxygen flux. An analysis of this process shows that for typical values of pyrite grades and limited temperature increases in the ore heap, the oxidation rate and penetration into the heap is reduced to values between about 30 percent and 50 percent of those obtained when leachate percolation occurs and water evaporation is not a significant mechanism of heat removal.IntroductionHeap biooxidation of refractory gold ores, needed as a pretreatment step to liberate the gold for subsequent extraction by leaching, requires large amounts of oxygen for the normal amounts of sulfide minerals that are typically present, one to two percent pyrite and/or arsenopyrite.The importance and potential limitations of oxygen transport into commercial ore heaps, which are much larger than encountered with column tests of ore and with pilot heaps, has been recognized111 • Commercial ore heaps using radial stacking conveyors are typically about nine meters high and may be 100 meters or more in lateral dimension. Three oxygen transport mechanisms have been identified and analyzed: ( 1) natural convection, which arises from an increase in buoyancy caused by the temperature rise and gas composition changes associated with the exothermic oxidation of the sulfide minerals within the ore heap, (2) forced air ventilation, using low pressure fans and air distribution pipes within the heap, and (3) diffusion of oxygen in the gas-filled void spaces within the ore heap driven by the oxygen concentration gradient from the surface of the heap to the mineral oxidation loci within it."

Jan 1, 1997

By F. Sanchez, A. Mejias, C. Frias, G. Diaz

"Crude zinc oxides are the major source of secondary zinc and are produced from fuming processes like Waelz kilns. The impurities of crude zinc oxides make difficult their processing in primary zinc refineries due to mainly high chloride tenor. Washing with sodium carbonate is a costly operation and chloride removal efficiency is not good enough, so further purification steps are required. The crude zinc oxides are easily treated using ZINCEX™ technology based on leaching, solvent extraction, and electrowinning. The ZINCEX™ process is commercially available and is designed to be a perfect barrier for metallic impurities and halogens, allowing selective zinc extraction in mixed chloride and sulfate leaching solutions. Other valuable components as lead and silver can be efficiently recovered from the leaching residue using PLINT technology in chloride media. Silver is recovered as silver cement and lead is precipitated as pure lead oxide or carbonate, which can be smelted at low temperature.IntroductionZinc is a fully recyclable metal and at present approximately 70% of the zinc produced worldwide comes from primary zinc while 30% originates from secondary materials. Nowadays, the zinc recycling rate is continuously increasing mainly through galvanized steel scrap processing, and crude zinc oxides are the major source of secondary zinc [1]. Secondary zinc oxides are obtained from fuming processes like W aelz Kiln, Rotary Hearth Furnace or Primus Furnace. Waelz is the dominant technology accounting for 80% of total crude zinc oxides production worldwide. In the Waelz process, steel dust is mixed with solid fuel reductant (coke breeze) and pelletized. It is then fed to the kiln and heated to a reaction temperature of l ,200°C. In such conditions, zinc, lead, and other non-ferrous metals are vaporized into the flue gas together with chlorides and alkaline metals. Mixed oxides are drawn from the kiln with the process gases and separated to produce typical crude zinc oxides [2]."

Jan 1, 2011

By Neusa Alonso-Falleiros, Aristeu Braz da Veiga, Marcelo B. Mourão, Adriano Pescarmona, Antonio Alberto Froes Schettino, Cyro Takano, Carlos A. S. Giraldo

"The Caron process of nickel extraction from lateritic ores produces a fair amount of an inert residue, the so-called “black sludge”, that is disposed in a dam according to the required environmental regulations. On the other hand, it represents an opportunity to resource recovery. This work presents the characterization of the residue, discusses some possible ways to recover the valuables, and presents experimental results of pyrometallurgical runs aimed at recover nickel as an iron-nickel alloy. It has been shown that the residue contains large amounts of silicon, iron, aluminum and magnesium, in the form of oxides and silicates, and small quantities of nickel, cooper and cobalt, besides several other elements. It has also been shown that gravimetric or magnetic concentration methods do not present promising results. On the other hand, it is possible to obtain iron-nickel alloys by high-temperature carbothermic reduction of the “black sludge”.IntroductionThe Caron process consists of a combined pyro-hydrometallurgical process to extract nickel from high iron limonitic lateritic ores, recovering also the cobalt present in the ore. The main steps are the reduction roasting of the ore, aiming at a selective reduction of nickel and cobalt to the metallic state, avoiding as much as possible iron reduction, followed by leaching with ammonium carbonate solution and the recovery of metal from the pregnant liquor [1,2]. As a result, significant amount of tailings are generated, that are disposed in appropriate dams. This residue, called “black sludge”, contains significant proportion of silica and iron, and also small amounts of nickel, cobalt, cooper and some other elements. Due to diminishing deposits of nickel ore, high metal prices and a significant amount of “black sludge “ available after several years of operation of the plant, Votorantim Metais, who operates a facility in Brazil that uses the Caron process, decided to explore the possibility of recover nickel from the residue. This paper presents the characterization of the residue, and the results of experimental work aiming recovery of nickel from it."

Jan 1, 2008

By Y. Fautrelle, F. Felten, O. Metais, Y. Du Terrail

"We deal with the prediction of electromagnetically-driven turbulent flows by means of a Large-Eddy- Simulation method (LES). The model is applied in the case of a liquid metal pool submitted to a polyphase linear electromagnetic stirrer. We investigate two cases: (i) the frequency of the magnetic field is equal to 50 Hz; in that case the effects of the pulsating part of the Lorentz forces may be neglected; (ii) the frequency of the magnetic field is low (f= 1 Hz), then the oscillating part of the electromagnetic forces is taken into account. The LES predictions agree well with the mean velocity measurements, as does the standard k-a model. However, as for the turbulent kinetic energy predictions, there is a large discrepancy between the two models. When the oscillating part of the Lorentz forces is taken into account, the computations show that the fluid flow is sensitive to the unsteady part of the forces. We find that the mean velocity is not affected by the fluctuating component of the force. As for the turbulence parameters, the presence of the pulsating part leads to a significant reduction of the turbulent kinetic energy, whilst the turbulence length scale decreases.IntroductionElectromagnetic stirring is commonly used in various metallurgical processes. In continuous casting for example, it may improve the structure of the solidified metal products. Fluid flows generated by electromagnetic stirrers have been extensively investigated (1 ). As for numerical predictions, many works have been published on the subject. In most of the previous works, onepoint closure models have been used. The most used model is the well-known k-i:: model. Those models yield fairly good results as for the mean velocity prediction. However, it has two main drawbacks:(i) the turbulence is not predicted accurately,(ii) it is not well fitted for unstationary flows as well as transitional turbulent motions, where theReynolds number is moderate."

Jan 1, 1999

By Robert W. Bartlett

"Economic and other factors, mostly outside of metallurgy, that strongly influence applied research, development and especially successful commercial adoption of new processes for producing primary metals and other commodity materials are reviewed. These factors, which can be both positive and negative in their influence, are often too lightly regarded in the research planning stage. They include continuing imperatives that have long influenced new process development as well as more recent trends. Both are discussed. Nearly all new materials eventually become commodities--products made to standard specifications with no producer control over price. Success requires being a low cost producer on a world wide basis. Composites and other complex material assemblages are unlikely to escape this fate as they mature.INTRODUCTIONThe adoption of new processes, beginning with research and development, for primary metals and other commodity materials is particularly difficult because each new process must supplant an existing process that is already being used commercially. There are many requirements besides technical innovation and cost superiority that must be met by the new process. Consequently, few innovations make it all the way from the research laboratory to commercial success.This paper discusses some of the factors that influence success in developing new processes for primary metals and commodity materials, based on the authors experience as a research metallurgist and industrial research manager. It begins with some of the factors that are always present and constrain successful process research and development, and proceeds to current trends that are expected to continue long enough to influence processes in the year 2000. Many of these trends are contradictory in their effect on new process development, and the future remains uncertain.The prevailing importance of these trends will vary with the material, process concept and other factors intrinsic to each case. Nevertheless, an awareness of these influences can help to avoid some of the R&D pitfalls and dead ends. Such awareness is deemed to be a necessary condition to avoid failure when commercial adoption of a new process is the goal."

Jan 1, 1988

By Takamasa Ishigaki, Gervais Soucy, Mohamed Rahmane

"The induction plasma jets employed for the in-flight nitridation of molybdenum disilicide (MoSi2) powders were investigated in terms of their flow characteristics. The present study shows the effect of the operating parameters of the plasma torch, as used for this process, on the plasma jet properties. The enthalpy probe techniques, along with mass spectrometry, were employed for the measurement of the jet temperature, velocity and concentration fields. The measured values were compared to the results of a numerical simulation performed on the plasma flowing inside the torch-reactor system. The process operating conditions studied were the plasma plate power, chamber pressure and sheath gas composition. The optimal conditions for effecting the nitridation process using thermal plasma are obtained at moderate plasma plate power, at around atmospheric pressure and by using a mixture of argon and nitrogen as the plasma torch sheath gas.IntroductionMolybdenum disilicide (MoSi2) based composites are considered to be one of the most promising candidates for high temperature structural material applications [!], especially because of their high melting points, good oxidation resistance and relatively low cost. However, the wide application of these composite materials is still limited by some factors such as their brittleness at room temperature and lower strength at high temperature (> 1500 K). To overcome such limitations, a number of researchers [2-4] have earlier studied various kinds of reinforcements for MoSi2, e.g. oxides, silicides and nitrides. More recently, Fan and coworkers [5-9] have demonstrated the possibility of in-flight nitridation and carburization of MoSi2, using a thermal plasma process. This work has confirmed the plasma synthesis route as one of the most promising methods for creating an in-situ second phase structure. Properties of the plasma flow, such as its temperature, flow velocity and composition, are of crucial importance for the nitridation of MoSi2 powders during their flight in the plasma. Therefore, the optimization of such a process involving plasma· generated reactive species necessitates a thorough understanding of the plasma flow characteristics."

Jan 1, 2000

Laminated ceramics have received widely scientific and commercial attention because their properties, such as mechanical properties and electrical properties, can be tailored by adjusting the structure, thickness and composition of the different layers. For example, ferroelectric Bi4T13O12 (BIT) which has a positive temperature coefficient of dielectric constant (TE) can be used to modify the negative of typical microwave dielectric ceramic BaNd2Ti4O12(BMT). However, BaNd2Ti4O12/Bi4Ti3O12/BaNd1Ti4O12 (BNT/BIT/BNT) laminated ceramics could not be prepared by the general method because the optimal sintering temperature of BaNd2Ti4O12 ceramic (around 1350°C was much higher than that of Bi4Ti3O12 ceramic (around /1100°C). in this research, a new method of spark plasma sintering (SPS) combined with post-sintering was successfully proposed to prepare BNT/BIT/BNT laminated divided proposed to prepare ceramics. It was divided into three steps. In first step, the BaNd2Ti4O12 ceramics were prepared by conventional sintering method. In second mop, the calcined and pre-pressed Bi4Ti3O12 powders were sandwiched between BaNd2Ti1O12 ceramic pellets and spark plasma sintered at 900'C for 10min to synthesize BNT/BIT/BNT composite ceramics. In the last step, a post-sintering was employed to reoxidize the partially reduced BNT/BIT/BNT composite ceramics. The results of scanning electron microscopy (SEM) and electron probe mircoanalysis (EPMA) showed that BNT layer and BIT layer were well bonded and no significant interfacial infiltration between them was observed. The sandwiched BNT/B1T/BNT ceramic with 10.7% BIT in volume has a dielectric constant of 92.8, a low dielectric loss of 0.0068 and a small temperature coefficient of dielectric constant v/35 ppm/C at 1 MHz.

Jan 1, 2003

By Yong .. Jun Wu

Laminated ceramics have received widely scientific and commercial attention because their properties, such as mechanical properties and electrical properties, can be tailored by adjusting the structure, thickness and composition of the different layers. For example, ferroelectric Bi4Ti3O12 (BIT) which has a positive temperature coefficient of dielectric constant (,E) can be used to modify the negative tE of typical microwave dielectric ceramic BaNd2Ti4O12(BNT), However, BaNd2Ti4O12/Bi4TiO12/Bi4Ti3O12/BaNd2Ti4O12 (BNT/BIT/BNT) laminated ceramics could not be prepared by the general method because the optimal sintering temperature of BaNd2Ti4O12 ceramic (around 1350°C) was much higher than that of Bi4Ti3O12 ceramic (around 1100°C). In this research, a new method of spark plasma sintering (SPS) combined with post-sintering was successfully proposed to prepare BNT/BIT/BNT laminated ceramics. It was divided into three steps. In first step, the BaNd2Ti4O12 ceramics were prepared by conventional sintering method. In second step, the calcined and pre-pressed Bi4Ti3O12 powders were sandwiched between BaNd2Ti4O12 ceramic pellets and spark plasma sintered at 900°C for 10min to synthesize BNT/BIT/BNT composite ceramics. In the last step, a post-sintering was employed to reoxidize the partially reduced BNT/BIT/BNT composite ceramics. The results of scanning electron microscopy (SEM) and electron probe microanalysis (EPMA) showed that BNT layer and BIT layer were well bonded and no significant interfacial infiltration between them was observed. The sandwiched BNT/BIT/BNT ceramic with 10.7% BIT in volume has a dielectric constant of 92.85, a low dielectric loss of 01068 and a small temperature coefficient of dielectric constant of 35 ppm/°C at MHz.

Jan 1, 2003

By P. Tapp, T. Evans, N. A. Molloy, J. Lucas

"Consideration of the protoype tuyere geometry for injection of inert gas through the bottom in a basic oxygen steel furnace and a requirement to specify an optimal flow for bottom wear and metal penetration led to experimental investigations[l,2] to apply the results of previous workers to this specific case, Flow velocity profile development within the tuyere was proposed as significant and the experimental scheme was designed to test this. It is proposed that the design criterion for the conditions of optimal flow of the prototype geometry be based on the non-dimensional mass velocity.INTRODUCTIONSharma[3] tested small diameter tuyeres in a laboratory hot model using molten iron to define a flow criterion for prevention of penetration of the bath liquid into the tuyere. Using argon, nitrogen and helium through a range of tuyeres (1 to 3 mm ill ) he proposed the jet Froude number C Fr' ) with the critical value being 2400 - 2500 or higher. Sonic or supersonic velocity was not a sufficient criterion. The tuyere design was a parallel tubular duct of moderate aspect ratio CAR) i.e. the ratio of length to diameter ranging from about 22 to 36 in the experimental furnace.Farmer et al[4] stated their their aim ""to develop a unifying explanation and procedure for the proper design of tuyeres"" but disagreed with Sharma's jet Froude number criterion. Recalculating Sharma's data they proposed instead a fully expanded Mach number of 1.75 with an initial expansion angle of ten degrees as the lower bounds of flow to meet the design requirement. They experimented with tuyeres in a water model using tubular, annular and convergent-divergent nozzles. The aspect ratio of the parallel duct tuyeres was from 533 to 762 using diameters of 1.4, 1.7 and 2.0 mm C the diameters being of tubes to be used full scale). Subsequently these results were applied to a prototype tuyere using a diameter of 1.7 mm with beneficial results in practice. This tuyere had an aspect ratio of 1067."

Jan 1, 1996

By Jie Ma, Bo Wang, Jieyu Zhang, Jian Zhao, Zheng Chen

"In this paper, solidification process of steel ingot was simulated by ProCAST software, based on cellular automaton-finite element (CAFE) model. A 22 t steel ingot was divided into continuous small zones (100x150x180 mm) in radial direction, then the temperature field, shrinkage cavity and porosity, particularly, the microstructure were simulated. The results show that: there was a columnar-to-equiaxed transition in microstructure on radial direction. Zones, closing to the center of the ingot, had a more developed and fined equiaxed zone, while zones closing to the periphery of the ingot had a more developed columnar zone. It indicated that temperature gradient has a great influence on microstructural morphology. Thus, the simulation results were highly agree with the experimental results, verifying the feasibility of this simulation method. It significantly reduces the time of simulation, and has important significance for predicting the microstructure of large steel ingot.IntroductionSolidification microstructure of steel ingot have a significant effect on the quality of the final steel products. Although many experimental works have been carried out in order to obtain the optimum condition for solidification process of continuous casting, it is also very desirable to establish mathematical models to simulate the evolution of solidification structure. The simulation methods can be divided into deterministic models and stochastic models, which have been developed rapidly over the last couple of decades. Cellular automaton method is one of the stochastic models. Rappaz and Gandin [1, 2], Nasatac and Stefanescu [3, 4] are the earliest researchers engaged in the this field. Moreover, Rappaz and Gandin simulated the solidification structure and CET (columnar grain to equiaxed grain transition) of metals using the CAFE method (cellular automaton-finite element method) for the first time [1, 2]. Recently, the CA (cellular automaton) model also considered the effects of fluid flow on the solidification process. Zhu, et al. [5-11] improved method of CA , they used the KGT model to describe the undercooling needed during the growth of the dendrite tip."

Jan 1, 2014

By Norihisa Iida, Yutaka Koshiba, Tsutoipu Masui

"Mitsubishi Materials has many years of experience in the production of oxygen free copper (OFC) and its alloys with a fully continuous-casting process. Four grades of OFC, commercial, electronic, superconductor, and ASTM class I are available according to user needs such as stabilizer for superconductivity, magnetron, and ultra-vacuum systems. Along with Cu-Ag and CuSn, we offer OFC based copper alloys such ·as Cu-Cr-Zr, Cu-Fe-P, Cu-Ni-Si and others, that are suitable for lead frame and connectors. Within the maximum sizes of 260mm X 1050mm for cakes and 385mm diameter for billets, we are very flexible and can adjust the ingot size to customer’s requirements. Other products that we can supply are semi-finished products such as hot rolled sheet, ·forged blank, extruded rod and finished products like mold for continuous casting of steel, ring mold for non-ferrous casting and backing plate for sputtering target.IntroductionMitsubishi Materials Corporation developed mass produced high quality oxygen free copper and. high copper alloy ingots in the 1960's. We produce 60,000 - 70,000 tons annually giving us 22 - 23% share of the world's market.Our oxygen free copper and. copper alloys are produced with a fully continuous casting process using only high-grade copper cathodes from our Naoshima and Onahama refineries. The raw material is melted and cast in' a carefully controlled atmosphere resulting in a product with low impurities and excellent properties.Using a controlled atmosphere it is possible to produce high quality copper alloys including active elements like chromium (Cr), zirconium (Zr), titanium (Ti), and magnesium (Mg) which are difficult to produce using standard batch casting methods.Using our own cakes and ·billets we produce and supply worldwide wrought materials like molds for ferrous and non-femous casting. These products receive special patented thermo-mechanical· treatments resulting in high strength and excellent conductivity with low cost."

Jan 1, 2000

By Xuling Chen, Zhiyun Ji, Min Gan, Wenqi Li, Xiaohui Fan, Zhiyuan Yu

"Specularite and vanadium-titanomagnetite are difficult to granulate, and with the increase of their proportions, the permeability of sintering bed is deteriorated together with the combustion velocity of fuel for the shortage of air through the sintering bed, which can lower sintering speed and specific production capacity significantly. The biomass fuel has a higher combustion velocity than coke breeze, therefore the productivity of specularite and vanadium-titanomagnetite ore can be improved remarkably by replacing coke breeze partly with biomass fuel .The results showed that, when the proportion of biomass fuel replacing coke is 40%,the sintering speed and specific production capacity of 35% specularite were improved from 19.06mm/min, 1.33 t/(m2·h)to 21.45mm/min, 1.47 t/(m2·h),and that of 55% vanadium-titanomagnetite were improved from 17.23mm/min, 1.11 t/(m2·h)to 22.80mm/min, 1.44 t/(m2·h). As a conclusion, biomass fuel is effective to strengthen sintering of refractory iron ore.IntroductionThe iron and steel industry of our country has achieved significant development in the recent years. In 2010, the output of steel has reached to 0.627 billion tons. The increasing scale of iron and steel has led to rigorous domestic iron ore environment, and the reserves of hematite and magnetite that have superior sintering characteristics are on the decline with continually exploiting and utilizing [1]. Therefore, the RIO (refractory iron ores) SP (specularite) and VT (vanadium-titanomagnetite) have to be applied vastly. However, the quality of sinters can be deteriorated when utilizing RIO in high proportion due to their poor granulation and metallogenic performances [2, 3]. Generally, the ratio of SP is 3~5%,which should not exceed 10% in our country currently [4]. Though high rate of VT is adopted in PZH steel for a long time, the productivity is obviously low compared with normal sintering [5]."

Jan 1, 2012

By Thomas Gliick, Jianming Lu, David Dreisinger

"The recovery of manganese from the Boleo project of Baja Mining is via an acid oxidation and acid reduction process in seawater. Manganese as manganese dioxide is leached into solution as manganese sulphate with the addition of sulphur dioxide gas as a reductant and then precipitated as a manganese carbonate. The use of the manganese carbonate intermediate to produce electrolytic manganese metal (EMM) has been extensively studied. The manganese carbonate can be used in place of natural (MnC03) or reduced ores (MnO) of manganese as a feed to the EMM plant. Manganese carbonate can be dissolved in spent electrolyte from manganese plating, followed by purification using ammonium sulphide precipitation of minor elements and then electrowinning in a selenium free process. The results of small cell testing of manganese electrowinning are reported.IntroductionThe Boleo Project of Baja Mining is a greenfields development currently under construction approximately 5 km north of the town of Santa Rosalia, Baja California Sur, Mexico. The Boleo property is held by the Mexican company, Minera y Metalurgica del Boleo S.A. de C. V. (MMB). MMB is owned 70% by Baja Mining Corp. and 30% by a consortium of Korean companies consisting of KORES - Korea Resources Corporation, LS Nikko Copper, Hyundai Hysco, SK Networks and lljin Copper.The Boleo deposit has Measured and Indicated resources of264.7 million tonnes grading 1.50% copper equivalent (CuEq) & Inferred resources of 159.9 million tonnes grading 1.15% CuEq. The calculation of copper equivalent is based on a combination of metal prices and predicted metallurgical recoveries (Table I). The metallurgical recoveries have been confined by extensive bench and pilot plant testing. Proven and probable reserves are available at Boleo to provide for more than a 30 year mine life. Initially, 25 years of mine life and 23 years of process plant operation have been scheduled in the February 2010 Technical Report Update (www.sedar.com)"

Jan 1, 2012

By Xavier Kleber, Aude Lamontagne, Veronique Massardier, Daniele Mari

"The thermoelectric power (TEP) technique was used to determine with high accuracy the strain ageing kinetics in heavily cold drawn pearlitic steel. Because of the very high sensitivity of the TEP to solute atoms, this technique allowed the strain ageing to be followed from the very first moments. The kinetics were followed during isothermal ageings performed between 20°C and 200°C for different strains. In order to avoid any ageing at room temperature, the samples were kept at -80°C immediately after cold drawing. TEP evolution versus strain highlights cementite decomposition occurring during cold drawing. During the ageing, a redistribution of the dissolved carbon atoms in ferrite occurred. The TEP increase with the ageing time was attributed to the departure of carbon atoms from ferrite (segregation to dislocations and/or carbide precipitation). The kinetics were analysed using the Johnson-Mehl-Avrami-Kolmogorov approach which enabled to determine activation energies associated with carbon atoms redistribution.IntroductionHeavily cold drawn pearlitic steel wires are commonly used as structural materials for their high strength and their acceptable ductility. However, several previous studies highlight the microstructural destabilization of pearlite mainly due to cementite decomposition during the drawing process, which induces changes of mechanical properties [1, 2]. This phenomenon was detected by several experimental techniques such as Mossbauer spectroscopy [3, 4, 5], themomagnetic analyses [6, 7], TEM [8, 9, 10] or atom probe tomography [9, 10, 11]. Nevertheless, the mechanism of cementite decomposition is still unclear. Several hypotheses were proposed in the literature. The first hypothesis relies on a strong interaction energy between carbon atoms and dislocations involving higher binding energy than that between carbon atoms and iron atoms in cementite [3]. The second hypothesis is the increase of the free energy of the interface between cementite and ferrite due to the fragmentation of cementite during deformation (Gibbs-Thomson effect) [8]. Some authors even suggest that the dissolution of cementite occur during a post-deformation ageing [12, 13]. It is worth"

Jan 1, 2013