Search Documents

By Patrick Clark

As part of the Mine Waste Technology Program (MWTP), a large-scale column test using bacteria and a sulfide ore was conducted at McClelland Laboratories, Inc., in Sparks, Nevada. Four technology providers participated in this demonstration. A mining company in Nevada provided the sulfide ore, process effluent and make-up water. A process effluent column, a chemical oxidation column, and the four biological treatment columns were set side by side on a test pad outside the laboratory building. The process effluent and chemical oxidation columns were used for experimental control. The goal of this project was to evaluate the viability and feasibility of using these biodegradation technologies to reduce the cyanide to the regulatory level of 0.2 parts per million (ppm) within an acceptable timeframe and with low operational costs. The column testing began on December 3, 1998 and operated until May 17, 1999. One technology provider reached the regulatory level within the 158 days. The remaining three biotechnology columns were approaching the regulatory limit at completion of the demonstration. The MWTP is funded by the U.S. Environmental Protection Agency (EPA) and is jointly administered through an interagency agreement with the U.S. Department of Energy (DOE).

Jan 1, 1998

By James Bennett, Jinichiro Nakano, Anna Nakano

Efficiency of the chemical looping combustion technology is adversely influenced by surface properties of oxygen carrier materials during oxidation–reduction process changes at elevated temperatures. In this work, natural hematite (Fe2O3) and alumina (Al2O3) supported Cu-spinel (CuFe2O4) oxygen carrier particles were isothermally exposed to redox gas cycles (air and 10 vol% CO–90 vol% Ar) at approximately 800 °C and studied using a high temperature confocal scanning laser microscope for real time alterations in surface morphology, roughness, and particle volume. 3D topological scans from each cyclic gas exposure indicated hematite particles exhibited noticeable volume expansion in reduction and shrinkage in oxidation, corresponding to respective phase transformations. Materials surface changes during the redox gas cycles are discussed.

Mar 1, 2017

By Edward P. Hagarty

The Hazardous and Solid Waste Amendments (HSWA) of 1984 added Subtitle I to the Resource Conservation and Recovery Act (RCRA), authorizing the Environmental Protection Agency (EPA) to develop and implement a new regulatory program for Underground Storage Tanks (USTs) containing petroleum and other regulated substances. Technical standards required for release detection, prevention, and correction as necessary to protect human health and the environment were promulgated as described in 53 Federal Register 37082 (September 23, 1988). Virginia State Regulations (VR 680- 13-02) and U.S. Army Regulations require that a Corrective Action Plan and a Site Clearance Report be prepared to explain the details of remediation of any contaminated media. Construction of new buildings is proposed in two different areas at Fort Myer in Arlington, Virginia, where USTs containing gasoline, diesel and heating oil were located. Tightness testing performed on these USTs in September 1991 indicated that some of the tanks were leaking. Many of the tanks were removed for permanent closure. Initial Abatement (excavation of contaminated soil) was &ed out immediately. A detailed Site Characterization Study which included Hydropunch", field screening using immunoassay, and pilot test - dual phase (water and soil gas) extraction was conducted. Environmental media were analyzed for volatiles, semi-volatiles and metals. A detailed risk analysis (RA) was performed to determine risk-based clean up levels for benzene, toluene, ethylbenzene, xylenes (BTEX); polycyclic aromatic hydrocarbons (PAHs); and methyl-tertiary butyl ether (MTBE). The RA also discussed the presence of lead in the soil. Before constructing any buildings in these contaminated areas, remediation must be conducted in accordance with the State, Federal and other applicable regulations. The remedial alternatives evaluated included Vapor Enhanced Groundwater Extraction, Soil Vacuum Extraction, Soil Washing, Soil Steaming, Active and Passive Ventilation SolidificationlStabilization, Vapor Barrier Construction, and Excavation with Off-site Disposal. This paper discusses: (a) delineation of soil contamination @) risk analysis (c) evaluation of remedial alternatives and selection of the most appropriate technology and (d) consideration of various regulatory issues.

Jan 1, 1994

By Garg. D.

Premixed bronze powders are widely used to produce a wide variety of P/M components including bearings and bushings by the powder metal industry. The physical and mechanical properties of sintered bronze components such as dimensions, strength, microstructural characteristics, and sintered density are well known to change with sinlering furnace design, particle size distribution in powders, green density, preheating and sinlering time" and temperature, and protective atmosphere flow rate. " However, not much is known about the effect of protective atmosphere composition on physical and mechanical properties of sintered bronze components; This paper describes effects of protective atmosphere composition and sintering temperature on physical and mechanical properties of sintered bronze components

Jan 1, 1996

Al2O3,-WC Composite powder for cutting tools was synthesized by self-propagating high-temperature synthesis using A1 powder as a reducing agent. WC, W2C and Al2O3 were concurrently formed in WO3Al-C system. It was found that the complete reaction was achieved with excessive addition of carbon and appropriate processing parameters such as degree of dilution, particle size of aluminum, compaction pressures of green pellets and carbon source. The final product which was leached by 50% HN03+HF diluted solution was consisted of Al2O3-55wt% WC having 2-3um of mean particle size.

Jan 1, 1999

By James P. Bennett, Jinichiro Nakano, Anna Nakano, Hani Abu El Hawa

Carbon feedstocks used in power, chemical and metallurgical industries typically contain numerous minerals or impurities that liquefy during high temperature processing to form slag as a byproduct. Slags have many industrial applications, for example, as construction materials and for element recovery. In addition to other variables, the extent of slag utilization is dependent on its com- position and post treatments. In this work, the in fluence of temperature and phos- phorus additions on phase evolution in coal slag was investigated. Synthetic slag mixtures with varying AlPO4 contents (0–14 wt%) were heated from 1380–1470 ° C in air, then water-quenched to preserve the phases formed. SEM/EDS, XRF and XRD analyses were performed before/after testing to gain insight about slag chemistry and phases present. It was found that coal slag exhibited a large solubility of phosphorous, affecting morphology of mullite formed under the conditions studied. Results obtained and their significance are discussed.

Mar 1, 2017

By James Bennett, Jinichiro Nakano, Anna Nakano

Previous empirical research demonstrated that by mixing gasification and metallurgical slags at a specific composition in a CO2 enriched environment, enough exothermic heat would be generated to transform CO2 to CO. The process capacity may be limited by the availability of the slags, however, it could be used to supplement existing energy or chemical production to reduce overall carbon emission. In this study, computational simulations were performed to explore optimal process conditions based on effects of individual slag constituents and thermal input for maximal gas conversion rate, heat production, and volume increase. In simulated conversions of CO2 to CO and H2O to H 2, comparisons were made by varying CaO, FeO, versus V2O3 slag constituents. The result indicated the optimal slag composition may be obtained by appropriate source selection and mixing of gasification and metallurgical slags in order to maximize carbon reduction and/or H2 production.

Mar 1, 2017

By Patrick R. Taylor

In the search for the development of more "environmentally friendly" and more intensive waste disposal approaches to meet more and more stringent environmental regulations, thermal plasma-based processes? are considered one of the most promising alternatives to well-established technologies such as incineration. This paper presents an overview on the research and development status of thermal plasma-based waste remediation technologies. The properties of thermal plasma are described. Due to its unique feature of high-energy intensity and super high temperature, thermal plasma is particularly capable of destroying organic-containing wastes. Its potential and promising application to waste remediation may include: treatment of incinerator ashes; metallurgical dusts (especially, electric arc furnace dust); medical wastes; radioactive wastes; and other Resource Conservation and Recovery Act (RCRA) listed hazardous wastes. Many research institutes and vendors have been involved in the development of thermal plasma-based waste treatment-technology encouraged by the cleanup programs supported by the Environmental Protection Agency (EPA), the Department of Energy (DoE) and the Department of Defense (000). More recently, thermal plasma-based waste treatment technologies (sometimes called plasma-enhanced pyrolysis) are focused more and more on not only just destroying organic wastes but also on how to practically, and economically recover energy contained in the organic waste materials in addition to the recovery of metals in order to offset the high operating costs.

Jan 1, 2003

By Donna Post Guillen

"Cyclopentane, a flammable hydrocarbon, is being considered as a working fluid for waste heat recovery applications using Organic Rankine Cycles with Direct Evaporators. A postulated failure mode consisting of a pinhole leak in a heat exchanger tube raises safety concerns due to autoignition of the working fluid. Experiments were conducted to determine the ignition delay time (IDT) of cyclopentane using an Ignition Quality Test™ (IQT™) device. Two sets of experiments were conducted per ASTM D6890 (with exception to charge pressure and temperature) to determine ignition delay of the fuel at atmospheric pressure for standard air (-20.95% oxygen) and vitiated air (13.3% oxygen) at a temperature of 803 K. Operation of the IQT device at a much lower pressure (1 bar) than normal operation (21.4 bar) with a standard injector led to very rich conditions and wetting of the stainless steel chamber walls. Catalytic effects are postulated to produce the small IDTs observed. Experiments were repeated with a modified injector to prevent wall wetting, resulting in average IDTs that are substantially longer.IntroductionCyclopentane is being considered for use as a working fluid in a Direct Evaporator of an Organic Rankine Cycle (ORC). In this configuration, the heat exchanger is placed directly in the flow of the hot exhaust gas, rather than using a secondary heat transfer loop to isolate the flammable working fluid from the heat source. This configuration offers the advantages of approximately 15% lower cost and improved efficiency over a standard ORC. However, placing a heat exchanger operating with a flammable hydrocarbon in the hot exhaust gas stream presents potential safety risks. If a pinhole leak were to occur in the heat exchanger, working fluid could leak into the hot exhaust stream. Gas turbine exhaust is provided to the Direct Evaporator at a temperature of approximately 803 K, whereas the autoignition temperature of cyclopentane is 634 K (Gallant and Yaws, 1993). Autoignition of the working fluid has been identified as the key risk for this type of system.Autoignition occurs when sufficient self-heating by chemical reactions takes place to accelerate reaction rates to produce full-scale combustion. This is in contrast to forced ignition, in which an external source (e.g., spark) is employed to initiate the combustion process. For combustion to occur, the fuel to oxidizer concentration must be between the lower (lean) and upper (rich) flammable limits. The reaction rate depends on the species concentration of the fuel and oxidant, the local temperature and pressure. Ignition processes are comprised of steps that take a fmite amount of time. This latent period prior to the start of combustion is referred to as ignition delay time (IDT)."

Jan 1, 2012

By Funsho K. Ojebuoboh

With several "green" applications in the horizon, bismuth has become an even more important minor metal in the smelting and refining of lead. Smelters with a complex sulfide feed invariably deal with bismuth. Its behavior during the smelting of lead in conventional sinter - blast furnace operation is discussed. Because it readily deports to the lead phase during the refining of lead, its separation from refined lead remained unsatisfactory in early lead production. When commercial requirements of bismuth in lead became more stringent early this century, the procedure whereby calcium and magnesium is used to debismuthise lead was developed. The present conduct of this 1936 process, the Kroll Betterton process, is discussed with emphasis on operational improvements.

Jan 1, 1995

By R. L. Nyirenda

The use of ammoniacal ammonium carbonate (AAC) leaching for the treatment of carbon steelmaking EAF dust has been investigated on a laboratory scale. The experiments have been conducted on dust samples obtained from three European steelmaking companies. As received, the dusts were found to be toxic when tested according to current EPA toxicity testing procedures. Toxicity was on account of the leachability of one or more of the following elements: Ag, Hg, Pb, and Cd. Leaching experiments with concentrated AAC solution at 40 " C showed that zinc oxide present in the three dust samples, 60-80% of the total contained zinc, was rapidly solubilized. Data on the dissolution characteristics of Cd, Fe, Pb, Mg, and Mn are also presented. Toxicity tests conducted on residues of the leaching experiments found these to have leachates below past and current EPA toxicity threshold limits.

Jan 1, 1993

By Z. Yang

The flotation behavior of the. green algae Chlorella vulgaris and a wild Chlamydomonas spp. was studied in the presence of Zn(II) using dodecylammonium chloride as collector. At about pH 6. both organisms readily float as amine concentration approaches lx10-3 kmol/m3. In addition, electrokinetic measurements were made on the organisms as a function of pH in both the presence and absence of Zn(II). It was found that the Zn(II) has a considerably greater effect on the zeta potential of C. vulgaris than on Chlamydomonas. Zn(II) adsorption studies also indicated that C. vulgaris is able to accumulate more Zn from solution than the Chlamydomonas.

Jan 1, 1991

By Jay S. Gunasekera

Since great emphasis is being placed on the manufacturing science and processing science programs in the Department of Defence and other government research agencies and industries; currently, extensive research on computer aided design(CAD)/ computer aided manufacturing (CAM)/ and computer aided engineering (CAE) is being conducted at Ohio University (OU) . OU has invested over a million dollars in CAD/CAM hardware and software. Design and analysis packages like ALPID, NIKE, STREAM, SHEAR, POLY_FLON, RINGROLL have been developed or modified at OUusing finite element method, finite difference techniques or enhanced slab analysis. Packages like ABAQUS, FLUENT, and NASTRAN have been extensively used.

Jan 1, 1990

By Michael S. Moats, Jan D. Miller, Wlodzimierz W. Zmierczak

"For many, hydrogen in a pure hydrogen economy would be like natural gas in today’s energy economy. Unfortunately, hydrogen’s physical properties are unsuited to the energy market’s requirements in terms of packaging, storage, transfer, and delivery. In this paper, a hybrid energy economy that packages hydrogen chemically on carbon atoms from various sources including recycled carbon dioxide is introduced and discussed. For this new hybrid energy economy to become a sustainable reality, the ability to recycle carbon dioxide and use hydrogen to create an appropriate energy product, such as dimethyl ether (DME), is needed. DME is recognized as a potential next generation, “beyond-petroleum”, environmentally benign commodity for energy storage and distribution. It is expected that to maximize the sustainability of the proposed hybrid energy economy, “green” hydrogen will be utilized. The “green” hydrogen would be created by the electrolysis of water powered by renewable energy sources, such as solar, wind or geothermal heat.IntroductionWith the growing concerns surrounding trends in global warming and increasing concentrations of “greenhouse” gases, such as CO2 and CH4, efforts to mitigate the emission of these gases from industrial sources are growing. With respect to CO2, the demonstrations of various capture and sequestration methods are underway around the world.The sequestration of CO2 is mainly focused on storing the gas underground or deep in the ocean. The Intergovernmental Panel on Climate Change (IPCC) estimates that 2000 Gtonnes of CO2 can be stored underground in depleted oilfields, un-minable coal beds and other geologic features [1]. Additionally CO2 may be stored at the bottom of the ocean. The lure of storing carbon dioxide in depleted oilfields or un-mineable coal seams is that an economic benefit (enhanced oil or methane recovery) can offset the costs of gas capture, transportation and storage. Unfortunately, all of these storage methods have potential for the release of CO2 or CH4 back into atmosphere or creating environmental damage (mobilizing heavy metals, disrupting deep sea ecology)."

Jan 1, 2008

By LeRoy C. Prichard

The scrap based steel producers in the United States generate an estimated 650,000 tons of electric arc furnace (EAF) dust annually which is classified as hazardous waste, K061. These scrap based producers commonly referred to as mini-mills represented 39% of the steel produced in 1994. Based upon the EAF plants being installed or planned today, it is a reasonable projection to anticipate 50% of the steel produced in the United States will be by EAF's. Using a straight line projection of percent of steel produced to tonnage of EAF dust generated, this will result in 833,000 tons of dust being generated upon the completion of these new EAF producing plants, presumably by the year 2000. Because the United States is a capitalistic economy, a steel producer is in business to make a profit therefore dust management becomes a very important variable in the cost of making steel. An EAF mini-mill dust management program must consider at least three components. First the handling of the dust must be in accordance with the law; i.e., the Environmental Protection Agency rules and state and local municipalities guidelines governing K061. Second, it must be an economical solution that allows a company to manage its dust processing costs, a component of its total steel production costs while producing steel at a profit. Third, the dust management program should be one that is environmentally responsible; viz., the program should reclaim or recycle the dust constituents, as feedstock materials or saleable products. The first component, obedience of the law seems to be a relatively straight forward, common sense objective; however, as nearly every mini-mill operation will testify it has been a area of changing laws with confusing variations when it comes to K061. Even more frustrating is the fact that obedience or compliance today does not mean that the company will be considered law abiding in the future.The liabilities associated with

Jan 1, 1995

By Yunqing Tian, Wenbin Huang, Weidong Zhang, Xiaopeng Wang, Gele Qing, Xiangjuan Duan

Pellet production requires iron ore concentrates have fine particle size, high specific surface area and good balling performance, so iron ore concentrates appropriate for pelletizing is limited compared to sintering. In order to extend the iron ore resources for pelletizing, the iron ore fines for sinter are studied in this paper.The effect of grinded iron ores o npelletizing, roasting and pellet quality were studied in this paper. The bond grinding index of iron ore fine is between 12.5 and 16.98 kwh/t. The grinded iron ore fine has good balling performance, the drop number and compressive strength of green pellet were improved with increase of grinded iron ore fine ratio. The compressive strength of roasted pellets were decreased with increase of grinded iron ore fine ratio, however it can be reached 2500 N.P −1 while proportioned with more than 80% of magnetite iron ore concentrate.

Mar 1, 2018

By Ann E. Visser

Aqueous Biphasic Systems (ABS) form upon the admixture of certain water-soluble polymers or polymers and salts above critical concentrations, and thus represent liquid/liquid extraction systems whose nature is entirely aqueous. We are currently investigating the utility of ABS (and its solid phase analogs) as "green" alternatives to the use of volatile organic diluents in separations of metal ions. Chaotropic (water-destructuring) metal ions with small negative AGhyd (e.g., Tc04) tend to partition quantitatively to the PEG-rich phase of an ABS, but even hydrated metal cations can be partitioned to the PEG-rich phase if a suitable extractant (e.g., halide, dye, crown ether, etc.) is used to produce a more chaotropic ion-complex.

Jan 1, 1999

By S. N. Monteiro, C. M. F. Vieira, A. P. N. M. de Sa, J. P. D. Vitorino

"This work has as its objective to characterize an ash waste and to evaluate its incorporation into a clay to produce bricks and roofing tiles. The waste is a type of fly-ash resulting from the incineration of a selected part of urban garbage, which is basically constituted of organic matter and plastics. The waste was submitted to mineralogical and chemical characterization. Compositions were prepared with incorporation of the waste in amounts of up to 20wt.% into athe clay. Rectangular specimens were prepared by extrusion and fired in a laboratory furnace at 900°C. The physical and mechanical properties evaluated were: linear shrinkage, water absorption and flexural rupture strength. The results showed that the waste is predominantly composed of quartz and calcium compounds. The incorporation of the ash was deleterious to the evaluated properties of the clay. It is suggested that the incorporation should be made in amounts below 5wt. % to avoid deleterious effect in the mechanical strength and water absorption of the clayey ceramic.IntroductionThe world attention has turned to a subject of great concern today, the production and disposal of large amounts of industrial wastes as well as wastes of various sources. When deposed in an unsuitable place, these wastes can cause considerable harm to human health and to the environment. Our planet suffers with air pollution, groundwater and soil contamination as well as silting of rivers and lakes with the growing amounts of our society wastes.The recycling of waste materials is of great interest to the industries, mainly due to the environmental agencies legislation. One of the practices for correct disposal of these wastes being investigated is to incorporate into red ceramics, such as bricks and roofing tiles. The natural variability of the characteristics of the clays associated with the relatively simple processing techniques and also the low performance required for the products allow the presence of relatively high levels of impurities in clayey ceramics."

Jan 1, 2011

By Luciano B. Oliveira, Alexandre M. Stumbo, Luis G. C. Marques, Valdo S. Marques, Sergio N. Monteiro

"Similar to the ethanol program, initiated more than 30 years ago, the recently created biodiesel program in Brazil is expected to rely on private initiative based on agribusiness for vegetable oil production. Campos dos Goytacazes is a large county in the northern of the state of Rio de Janeiro with land still available for oily vegetables plantation in addition to the land traditionally occupied by sugar cane plantation, which is used to produce ethanol. In order to extend the biodiesel program to Campos dos Goytacazes, the State University of Northern Rio de Janeiro (UENF) is conducting a technical project for the development of the infrastructure for biodiesel production. In this work, the infrastructure based on versatile equipment for biodiesel esterification built in the Center for Alternative Energy of the UENF is presented.IntroductionBiofuels are gaining worldwide attention as a possible economical solution for the prediction of declining reserves of petroleum and related increase in price of barrel. However, nowadays, a more relevant question is the climate changes caused by burning fossil fuels. This is especially the case of coal and petroleum based fuels, mainly gasoline and diesel that propel the majority of vehicles and generate a large amount of CO2 emissions responsible for global warming. This combination of economical an environmental problems is already providing a strong motivation to substitute conventional fossil fuels by renewable biofuels. More than just the interest of the market financial forces, government legislation is imposing a new order that obliges the use of biofuel. Many countries including the USA, the European Community, Japan and Brazil are committed to gradually substitute biofuels into their fleet of vehicles."

Jan 1, 2008

By Yuanbo Zhang, Zhaokun Tang, Mingjun Rao, Guanghui Li

The ballability of hematite ore with addition of a certain amount of pulverized anthracite and the induration features of anthracite–containing hematite pellets were studied. The results indicate that adding a certain proportion of anthracite can improve the quality of green pellets as well as the roasting performance of roasted pellets. The suitable mass dosage of anthracite is 1.0%–1.5%. Under the conditions of roasting temperature 1280 oC–1350 oC and roasting time 15 min–20 min, the compressive strength of roasted pellets is found to be more than 2500 N/P. Compared with hematite pellets in the absence of anthracite, the proper induration temperature is diminished by 20 oC, whereas optimal induration temperature range expands by 50 oC, and induration time is shortened by 5 min–10 min. Adding anthracite is an effective measure to improve the pelletization of hematite.

Jan 1, 2015