Search Documents

By Alana Pereira Ramos, Walman Benicio de Castro

Amorphization and martensitic transformation (Ms) characteristics of Ti–Ni-Cu alloy ribbons prepared by melt spinning were investigated by means of differential scanning calorimetry and X-ray diffraction. In these experiments particular attention has been paid to change the wheel linear velocity from 21 to 63 m/s. Then the cooling rates of ribbons were controlled. The effect of this cooling rate and alloy composition on martensitic transformation behavior is discussed.

Jan 1, 2015

By Wan Pu

Chrysotile asbestos samples from different mines have been studied by SEM and TEM, including high resolution electron microscopy, to find reasons for differences in physical properties of different types of asbestos fibres. The results show that the inner diameters of fibre tubes and the lattice images of fibres are different for soft and hard asbestos fibres. These differences are related to temperatures and geochemical conditions during the growth of chrysotile asbestos.

Jan 1, 1989

By Kurt Westerlund

Three. years operating experience of the FLUXFLOW waste heat boiler (WHB) 20.000 nm /h at Boliden Ronnskar Sweden on a TBRC smelting palena (PbS). Operating experience from the Kivset flash WHB 11.900 nm /h at Samim, Porto Vesme, Sardinia, Italy. Conceptual features of the 93.600 nm3 /h FLUXFLOW (WHB) on the Isasmelt smelting in melt furnace for 180.000 t Cu/a at Mount Isa, Australia.

Jan 1, 1992

By Sugui Tian

By means of the T6 treatment, the measurement of creep curves and microstructure observation, the influence of T6 heat treatment on the microstructure and creep properties of Ti-6Al-4V alloy is investigated. Results show that the microstructure of the forged alloy consists of the banded-like a phase and networks b phase. After sub-temperture T6 treated, the microstructure of alloy consist of the block a phase and ?networks basket? structure. Under the conditions of the applied stress of 575 MPa at 4000C, the forged alloy displays a lower creep lifetimes, after T6 treated the creep lifetimes of the alloy is enhanced to 548 h from 66 h, which is attributed to the formation of the network basket structure in which the needle-like phase are dispersedly distributed. As creep goes on, the denser dislocations in the a phase are concentrated to occur the dynamic recrystallization for refining grain. which is a main reason of the alloy displaying a better creep lifetimes and plasticity. Thereinto, the creep mechanism of the forged alloy is thought to be the slip of the straight <a> and <a+c> dislocation are activated on the prismatic planes and pyramidal planes, while the creep mechanism of T6 treated alloy is that wave-like <a+c> dislocations are activated on the pyramidal planes.

Jan 1, 2009

By Yurniko Nakamura

Hydriding properties and crystal structure of a Ti-V- Mn solid solution alloy have been studied by P-C isotherm measurements and neutron and X-ray powder diffraction. The absorption P-C isotherm at 298K shows two plateau regions at 0.01MPa and 1MPa. The X-ray diffraction data have demonstrated that three phases with a BCC, a pseudo-cubic FCC and an FCC structure form subsequently with increase of the hydrogen content. Crystal structure of the latter two phases has been determined by Rietveld refinement of the neutron diffraction data. The FCC phase is the di-hydride of CaF2 type with hydrogen occupation in the T sites. The pseudo-cubic FCC phase is the mono-hydride of NaCl-type with hydrogen occupation in the 0 sites, which has not been reported so far. The lattice constants of the mono-hydride (Ti1.0V1.1Mn0.9)H_2.7 are a&apos;=0.407 nm for two axes and c&apos;=0.390 nm for the third axis. The a&apos;axis is shorter by 4% than the c&apos;axis. This pseudo-cubic FCC lattice is formed by contraction of 5% of the a axis and expansion of about 30% of the c axis from the original BCC lattice.

Jan 1, 2002

By Charles L. Richman

The effect of the addition of Silver Sulfide on the rate of Chalcopyrite (CP) of Sulfuric acid (H2SD4 leaching is discussed, Although Ag2S in an expensive addition, a theoretical explanation of it&apos;s use will aid in the development of a economic substitution. We have used cyclic voltammography to show the presence reaction species at different potentials. Cyclic Voltammography maps the surface reaction current peaks on CP, to regions on the CP Phorbaix diagram. AC Electro-lmpedance spectroscopy (EIS) models the surface impedance properties, which control the rate of electron and ion transfer, and the surface kinetic reactions, with and with out light. EIS and other measurements show that AgCuS u Photo-reactive material- The EIS results are compared with the SEM and EDXA results to show the presence of diffusion pores, and diffusion controlled reactions during CP leaching without the addition of silver sulfate. We hypothesize that AgCuS is an ionic conductor like Ag2S. EIS shows an imposed negative leaching rate greatly. Our theory shows how the formation of Silver Copper (1) sulfide layer at open circuit potential gives an effect similar to negative potential, that is enhanced with illumination. We verify that AgCuAS is an N-type semiconductor that forms a diode type junction with the electrolyte with the Mott-Schoottly relation.

Jan 1, 2001

By J. R. Donald

Surface and interfacial phenomena play a significant role in refractory performance. For example, the wettability of the refractory material with slag, matte, and metal influences infiltration and interfacial reactions. Yet, very little fundamental information regarding the surface properties of refractory materials and slag is available. Thus, in the present work, the sessile drop technique incorporating a high temperature furnace equipped with X-ray fluorescope was employed to investigate the surface and interfacial phenomena of fayalite-type slags on solid alumina at 1200?C. The iron to silica (Fe/SiO,) ratios employed were 1.4 and 2.0, and the oxygen potentials used were log p02 =-11 and log p02=-9 atmospheres. The contact angle between the fayalite-type slags and the alumina were determined to be relatively low, at about 16.9 to 19.6 degrees under the experimental conditions. The surface tension of fayalite slag (Fe/SiO2=1.4) at an oxygen potential of log -11 was 0.298, which agreed with the work of previous researchers. The surface tension of the fayalite was observed to increase with time. The spinel FeAl2O4. was determined to be the product of the interfacial reaction, and 8.8 to 15.8 mass percent alumina was dissolved into the slag after 40 minutes.

Jan 1, 1996

By Brandon R. Ball

An investigation of the effects of ozone and ozone-induced hydroxyl radical on reducing whole effluent toxicity is described and discussed relative to the application of ozone for industrial water treatment. Results from operation of an ozone system treating industrial effluent from a lead and zinc mine in Colorado are presented. The mine discharges 1,000 gpm of wastewater into a tributary of the Arkansas River and has historically exceeded Whole Effluent Toxicity (WET) limits and on occasion has exceeded numeric limits for copper, ammonia, and cyanide. Based on results of a Toxicity Identification Evaluation (TIE) conducted on the effluent and individual process waste streams, the source of effluent toxicity is believed to be primarily associated with organic reagents used in the milling process. Based on test results, an applied ozone to COD ratio of 3: 1 by weight and a contact time of 30 minutes was found to be effective for reducing whole effluent toxicity at pH 11 but not at pH 7, indicating oxidation by hydroxyl radical to be the dominant mechanism responsible for toxic-ity reduction. At an applied ozone to COD ratio of 3:1 and a pH of 11, toxicity was improved from 0 percent survival to 100 percent survival for Ceriodaphnia dubia and fathead minnow (Pimephales promelas) based

Jan 1, 1996

By Xin Zhang, Mengqi Li, Hongxu Li, Xinrong Zhang, Hao Bai, Ning Li

"Organic Rankin Cycle (ORC) is an effective technology to transform low-grade energy resource into electricity. In this paper, based on thermodynamic principle, considering the waste heat resource lower than 120°C, thermodynamic properties of ORC with working fluids ofR245fa, mixed R21/R245fa and mixed Rl52a/R245fa were assessed. The results show that high evaporation temperature contributes to improved system performance. The Rankine Cycle that uses R21/R245fa can increase net cycle output, thermal efficiency and exergy efficiency by 3.02%, 2.35%, and 4.44%,respectively, as compared to that with pure R245fa. When using Rl52a/R245fa as working fluid, the net cycle output can increase by 3.83% at most, while the thermal efficiency decreases by 8.7%. These results indicate that R21/R245fa has a good advantage in improving the cycle thermodynamic performance.IntroductionOrganic Rankine cycle is usually used for low temperature power generation, and is applied to the conversion of geothermal energy, low-temperature solar energy, ocean thermal energy and industrial low-temperature waste heat etc. Traditional Rankine cycle is quite mature already, however, organic working fluids would affect significantly the general efficiency of the entire thermodynamic system. Thus, selection of proper working fluids and development of new highperformance cycle is becoming important."

Jan 1, 2013

By Yuanbo Zhang, Mingjun Rao, Weiguang Tian, Huimin Tang, Guanghui Li, Lei Ye, Guoshen Liang, Zhiwei Peng, Foquan Gu, Tao Jiang

The amount of slag produced from a typical ferronickel smelting pro- cess is 4 to 6 times that of the metal product, and handling this slag is a huge challenge to the ferronickel industry. The feasibility of a technological route for preparing refractory materials from a ferronickel slag was verified in this study. Based on the thermodynamics analysis, the effect of the sintering temperature on the properties of refractory material from the slag was studied in the presence of magnesia. The results of thermodynamics calculation showed that the reaction of MgO with SiO generated forsterite and enstatite, whereas the reaction between 2 MgO and Fe O /Al O produced corresponding magnesia spinels. The experi- 2 3 2 3 mental results showed that a refractory material with refractoriness of 1580 °C, bulk density of 2.88 g/cm3, compressive strength of 106.9 MPa, and apparent porosityof 5.8%was obtained under the conditions ofmagnesia addition of 15 wt %, sintering temperature of 1350 °C and sintering time of 3 h. With increasing sintering temperature, the bulk density and the compressive strength of refractory material increased but the apparent porosity decreased, mainly attributed to the formation of the liquid phase which promoted the densification of the refractory material. (cid:1) (cid:1) (cid:1)

Mar 1, 2018

By Kenji Monden

A thermal solution composite is made by incorporating dense inorganic fillers with high thermal conductivity into a resin. Silica, alumina, aluminum nitride, silicon nitride, and boron nitride are used for fillers of thermal solution composite. The thermal conductivities of composites are measured and the effect of inorganic fillers’ volume fraction is analyzed. The influence of percolation on thermal conductivity is considered. When percolation by random filling is assumed, the thermal conductivity of composite materials is expressed by the predictive expression using the effective thermal conductivity of filler. The relationship between the effective thermalconductivity of filler and its mean diameter is estimated by the equation. In the case of irregular AlN filler with average particle size 45 lm, the effective thermal conductivity of filler becomes 20 Wm−1 K−1. When the volume fraction of the fillers is 0.75, the thermal conductivity of the composite has been reported to 8 Wm−1 K−1. If the thickness of the interfacial region can be lowered, an effective larger thermal conductivity of the filler appears to set in and the thermal conductivity of the composite can be largely improved. The thermal conductivity of BN can approach 600 Wm−1 K−1. The BN constitutes the matrix of composite by causing percolation without interfacial region; high thermal conductivity of 55–100 Wm−1 K−1 has been achieved.

Mar 1, 2017

By Run-boWang, Fan-yi Meng, Jian-Liang Zhang, ZheWang

To elucidate the influence of high Al2O3 content on sinter softening and melting behavior, heating-up reduction test under load was carried out. In addition, microstructure study of sinter bed structure change at a different temperature was also made and the mechanism that the effect of Al2O3 content on sinter softening and melting property was discovered. SEM results showed that the increase of Al2O3 content favored the formation of Al2O3-rich slag phase, such as the eutectic (2CaO·SiO2-2CaO·Al2O3·SiO2-FeO) and gehlenite (2CaO·Al2O3·SiO2), resulting in the decrease of sinter Ts temperature. Further, high Al2O3 content improved the concentration of metallic iron and lowered the dripping temperature due to the decrease of slag liquidus temperature and viscosity. At a fixed basicity, it was indicated that there was a relationship between Al2O3 content and sinter softening-melting property. Based on the results, counter strategies to cope with the adverse effect of high Al2O3 content on the cohesive zone property were also proposed. It could provide guidance for the blast furnace operation of sinter with high Al2O3 content.

Jan 1, 2015

By Geysen. Daneel

Better slag valorization is part of improving the sustainability of steel, stainless steel and non- ferrous metal production processes. Besides, it can improve the sustainability of other products and production processes as well. A sound and well established slag valorization is beneficial for the overall economics, marketing and appreciation of the metallurgical process and its products. On 6-7 April 2009, the First International Slag Valorisation Symposium was held in Leuven, Belgium. This paper gives a brief summary of the symposium, providing an overview of slag valorization opportunities. The authors believe that high temperature process slags can have interesting applications and that within the next 10 to 20 years slags will need such valorization options in order to compete with other materials and get general support for further production. On the other hand, the authors also expect a higher demand for slags for the production of various materials. High temperature processes should anticipate on the growing opportunities for valorization of slags and increase the resilience of their process by better understanding slag processing, slag quality and material requirements. More interdisciplinary research efforts are required to reach this level of knowledge for the different high temperature processes. Such an interdisciplinary research platform was recently established at KULeuven, Belgium, named SMART-PRO2 (Sustainable Materialization of Residues from Thermal Processes into Products).

Jan 1, 2010

By B. C. Curson

A comprehensive simulation of .the gas handling system in BHP Copper&apos;s San Manuel smelter was developed using AFT Fathom software, with the objective of minimizing SO2 emissions while maximizing smelter throughput. Once verified with plant data, the simulation quickly revealed&apos; the complex interactions occurring between individual converters and the flash furnace. The increased understanding provided by the simulation allowed novel, counter-intuitive control strategies to be developed and tested successfully.

Jan 1, 1999

By S. S. Bogomolov

The relationship between the magnetic properties and micro- structures of Pr-Fe alloys rapidly quenched by melt-spinning and highly undercooled by containerless processing in the Cambridge drop-tube was studied. The maximum measured coercivity, Hc, of as-cast samples was 4450 Oe for Pr-2 wt.%Fe. However, rapid quenching or melt undercooling decreases coercivity for hypo- eutectic alloys (<10 wt.%Fe) and increases Hc for hyper-eutectic systems.

Jan 1, 1992

By J. E. Dutrizac

The behaviour of the lanthanide elements during the precipitation of sodium and potassium jarosites at 98oC from sulphate media was systematically investigated. The lower atomic weight lanthanide elements (La to Gd) are characterized by the limited solubility of their alkali-lanthanide sulphates, such as NaNd(SO4)2?H2O, which commonly contaminate the jarosite precipitates. Hence, single phase jarosite-type compounds were precipitated only from solutions containing <0.4 g/L of the La to Sm lanthanides. The sulphates of the heavier atomic weight lanthanide elements (Tb to Lu) have significantly higher solubilities such that solutions containing up to 10 g/L of the individual lanthanides could be investigated without the precipitation of alkali-lanthanide sulphate species. Even at the highest lanthanide concentrations, however, none of the jarosite precipitates incorporated more than 0.3 wt% of any of the lanthanide elements. Comparable levels of lanthanide incorporation were noted in both Na-jarosite and K-jarosite. Although the mass of the jarosite precipitate increased with increasing ferric sulphate concentration or with increasing pH, the extent of lanthanide incorporation was not significantly affected. Clearly, the trivalent lanthanide elements do not substitute extensively for trivalent iron in the jarosite structure. This behaviour likely reflects the significantly lower hydrolyzability and larger size of the trivalent lanthanide ions relative to ferric ions.

Jan 1, 2003

By Johannes Boonstra

High rate bacterial catalyzed processes can serve to improve hydrometallurgical operations. These solutions are not only economical but also environmental sustainable. With references around the globe, the value of this new approach is recognized by industry worldwide. For instance, metals can safely and economically be separated from process and waste streams using biotechnologically produced sulfide, recovering a valuable metal sulfide product instead of a waste gypsum stream for disposal. Both the natural biological sulfur and nitrogen cycles offer bioconversions that are applied on industrial scale. The shared advantage of these processes is that waste compounds are converted in either a reusable raw material or in a harmless product. This way, natural product cycles can be closed. Applications based upon bioconversions are for example: Sulfur based: Bioleaching, reduction of oxidized sulfur compounds to elemental sulfur, metal recovery with biogenic produced H2S, SO2removal from gas streams, etc. Nitrogen based: Ammonia removal using the anammox-process, biological removal of NOxfrom gas streams, nitrate removal from water streams, etc. Metals: Bacterial processes for the reduction of metals such as uranium, selenium and manganese have proven to offer great potential for clean-up of groundwater streams. This paper contains a description of the above applications. Further, a short introduction on engineered high rate bioreactor systems and a description of industrial biotechnological applications will be provided.

Jan 1, 2003

By M. Oliazadeh

The present study was performed to develop a process for solvent extraction of molybdenum and cobalt from an acidic solution generated by an electrodeposition process of nanocrystalline cobalt alloys. Solvent extraction is a common practice in hydrometallurgical and refining processes to produce metals; however its application for separation of molybdenum and cobalt from this specific solution is new, because molybdenum and cobalt are not commonly associated together in nature. Five commercial organic extractants were examined for extraction of cobalt and molybdenum from synthetic acidic solutions with pH ranging from 1 to 5. Preliminary results showed that at pH 2, any of the Cyanex 923, Alamine 336, Aliquat 336 and Hostarex A327 could be used to extract 99% of molybdenum from solutions, while from pH 3 to 5, Aliquat 336 was able to extract about 100% of molybdenum. Cobalt extraction, on the other hand, varied from 15% to 23% at pH 3 and 30% to 53% at pH 2 using different extractants. Based on results obtained, Aliquat 336 was applied on mixed solutions of cobalt and molybdenum at various pHs. The results showed that molybdenum could be extracted as much as 99% from a mixture of molybdenum and cobalt at acidic pHs, while less than 1% of cobalt was separated at pH 2 to 4 simultaneously.

Jan 1, 2003

By Ilkka V. Kojo

This paper gives an overview of the primary copper smelting business during the years of flash Smelting in the light of various projects taking into account the sustainability of copper production. Also the future challenges of copper smelting are addressed with special emphasis on the environment. Flash Smelting connected with either Peirce-Smith converting or Flash Converting offers the most economical and environmentally friendly alternatives for the smelting of normal and lean copper concentrates. For rich copper concentrates the feasibility of Outokumpu Direct Blister Flash smelting is, understandably, beyond compare. When the total investment costs for building a smelter and acid plant are considered, it is clear that Flash Smelting is the more feasible option compared to bath smelting. Reduction of equipment and operating cost is further achieved by the LUREC-process developed by Outokumpu Technology for operating plants with SO2-contents up to 25 % by volume. As an example the Kennecott-Outokumpu Flash Converting Furnace (FCF) has been in operation at Kennecott Utah Copper for 10 years and has achieved excellent results both environmentally and production vice. The FCF treats the entire output of the Kennecott Flash Smelting Furnace and has excess converting capacity. Furnace life, initially projected at two to three years, is now projected to be more than 5 years. It is likely the life will be essentially the same as a well-operated Flash Smelting furnace.

Jan 1, 2006

By Keith E. Forrester

This paper presents results of laboratory and field optimization of a proprietary processes developed by FESI for the stabilization of heavy metal bearing wastes. The specific waste studies presented within the paper include foundry ash, aluminum sweat furnace ash and a heavy metal contaminated soil. The FESI process chemistry and engineered processes were found to be the most cost efficient demonstrated and available method of stabilizing heavy metals and highly successful in passing regulatory limits.

Jan 1, 1994