Search Documents

By A. Galvan

High rate compressible media filter (CMF) tests produced exceptional total suspended solids (TSS) removal at hydraulic loading rates ranging from 97.8 to 122.2 m/h. The compressible media is manufactured from a robust resin fiber that can withstand low pH and temperatures up to 149 °C. The media porosity can be varied by applying compression onto the media. At 40% compression, the CMF can remove particles greater than 4 μ. Three synthetic test-samples were generated by Hazen Research Inc., (Golden, Colorado) to simulate the copper Pregnant Leach Solution (PLS), Raffinate and Electrolyte solutions used for the testwork conducted at their facility. The preliminary results showed that the CMF was very effective in removing TSS without the use of chemical conditioning from the above test-solutions with efficiencies of 98%, 97%, and 96%, respectively. Given the remarkably high hydraulic loading rates, the industrial equipment footprint would be minimized appreciably over conventional clarification and alternative filtration systems.

By Chengyi Ding, Xuewei Lv, Changyang Ji, Rende Zhang, Xiangwei Zheng

Inexpensive and high-quality sinter has an extraordinary position in iron making, and there are many factors influencing the sintering. This research takes the basicity and coal dosage as research subjects to do the experiments based on cost analysis with sinter pot experiment system. Linear program is taken to make the schemes of ore blending. During the experiments of changing basicity from 1.6 to 2.3, the properties and microstructures of the sinter are studied. It comes to a conclusion that increasing the basicity is beneficial to sinter quality but leads to higher cost. To further ascertain the cost of sinter and the potential of saving coke, the work of improving coal dosage is taken on the basis of experiments of changing basicity. Through analyzing the results, a formula (Y=1849+261.1R-130.6C) is proposed which indicates the relation among the cost, basicity and fixed carbon content. And it works well for actual production.

Jan 1, 2015

By Chengyi Ding, Yangyang Xie, Xuewei Lv, Senwei Xuan, Chenguang Bai, Kai Tang, Gang Li

Dicalcium ferrite (2CaOFe2O3, C2F) is one of the most significant bonding phase of fluxed sinters. Reduction of C2F was investigated via thermal kinetics analysis. The isothermal reduction behavior of C2F by 30% H2 and 70% N2 at 1123 K (850 °C), 1173 K (900 °C), and 1223 K (950 °C) were discussed by thermogravimetric analysis in this paper. The results revealed that the C2F reduction was typical one-step reaction. The apparent activation energy of the C2F reduction was 27.40 kJ/mol. The rate-determining steps of the C2F reduction were the first inner gas diffusion, then the inner gas diffusion and interface chemical reaction mixed controlling. The ln-ln analysis implied that the C2F reduction was described by the Avrami–Erofeev (A-E) equation, thus appeared as a 2D A-E equation kinetics reaction.

Mar 1, 2018

By Slobodan Radosavljevic

The polymetallic W-Pb-Bi-Ag ore from the ?Nova jama? ore zone of the Rudnik ore field have been investigated. Contact-pneumatolytic (skarn), pneumatolytic-hydrothermal, and hydrothermal mineralization phases are defined in this ore zone. The most significant mineralization phase that gave compact ore bodies is pneumatolytic-hydrothermal phase. A relatively pure Mo-free scheelite is the only tungsten-bearing mineral. Lead minerals are mostly presented by Pb-Bi sulphosalts and much less with galena. The image analysis coupled with Energy Dispersive Spectrometry (EDS) analysis on a Scanning Electron Microscope (SEM) was applied to the characterization of a W-Pb-Bi-Ag ore as an efficient tool for mineral quantification. Results of EDS (Energy Dispersive Spectrometry) analyses gave the empirical formulae: Pb1.91Ag0.05Cu0.08Bi1.93S5 for cosalite, Pb0.98Ag0.03Cu0.05Bi1.99S4 for galenobismutite and galena Pb0.99Ag0.03S.

Jan 1, 2006

By Michael P. Sudbury

Non-ferrous slags are granulated and stockpiled as an alternative to pit cooling or transporting molten slag to a dump. The chemical composition of such slag is determined by the pyrometallurgical process in which it is produced, while the size distribution is set by safety concerns or a desire to reduce wear of pumps, pipelines and other equipment. Relatively few operations give consideration to the effect of granulation conditions on other properties of the granulate as the material is typically accumulated on the smelter site. It is becoming recognized that slag has many potential commercial uses and carries much of the energy applied to the smelting operation. This paper outlines the findings of extensive work to identify uses for granulated non-ferrous slag, the importance of preparation conditions on the properties, impediments to more extensive use of granulated slag, the real costs of slag stockpiling and the opportunities for further productive research.

Jan 1, 2006

By Sergio Neves Monteiro

This work had as its objective the characterization of a waste material, steel slag, generated from an integrated steel plant, with a view to its recycling and incorporation into red ceramics fabrication. The characterization was performed in terms of chemical composition by X-ray fluorescence (XRF), particles size distribution, X-ray diffraction (XRD), thermal analysis (DTA/TG) and scanning electron microscopy (SEM). The results indicate that the steel slag presents high amount of Ca, Fe, Mg and Si. The weight loss of the steel slag at temperatures above 800oC is associated with calcium carbonate decomposition. The coarse particle size of the steel slag is inadequate for its direct recycling into red ceramic fabrication. It is necessary to screen or to grind the waste. As a possible solution, it is suggested that screening or grinding the steel slag to a convenient particle size distribution would allow its successful industrial incorporation into red ceramics products.

Jan 1, 2006

By J. Jakumelt

The coupled simulation of mold filling and solidification for an investment casting process presents difficult. This is due to the complexity of the carious physical process and the geometry, To achieve this task in a precise way, the CFD program FLUENT and the casting simulation tool CASTS were closely coupled. Any physical quantity, such as velocities or temperatures, can be exchanged via files after each time step of the simulation. The communication and operating sequence of the programs is controlled by PERL-scripts. This enables the expertise of FLU ENT for flow simulation and the strength of CASTS, for casting simulation to be combined. The coupled simulation was successful applied to an aerospace investment casting. Several physical models were tested for correct treatment of the casting filters, the porosity of the mold and the viscosity of the liquid metal. The results demonstrate that even complex investment casting geometries can be investigated using CASTS-FLUENT.

Jan 1, 2003

By Leon H. Bruner

This paper presents a case study describing how a global consumer products company with 138,000 employees that markets over 300 brands in 180 countries is building sustainability into the rhythm of its business. This strategy extends beyond social investment programs by incorporating sustainability into the fabric of product design, manufacturing operations, employee engagement and stakeholder partnerships. During the implementation of this program it has been necessary to be explicit about sustainability and its importance to the business, to broadly define sustainability, to ensure that sustainability is not added work, to eliminate trade-offs between performance, value and sustainability and to implement programs to ensure that sustainability is incorporated into the DNA of the company. Our program continually emphasizes the importance of making no tradeoffs between consumer acceptance of sustainable products and sustainability investments. We also work diligently to overcome the challenges of engaging employees around the world to implement a single coherent sustainability strategy that delivers great results.

Jan 1, 2010

By Yanjie Liang

Elemental sulfur and volatilization kiln slag(VKS)containing heavy-metal produced by smelter factories were used to produce sulfured building material. The effects of heating mode, material proportion (MSulfur:MVKS), size of waste particles and ratio of aggregate to filler(A/F) on the mechanical properties and leaching toxicities of solidified stuff were investigated. The optimal conditions for the solidification are stepped heating mode, 3:7 ratio of MSulfur to MVKS, particle size less than 150µm and 3/17 ratio of A/F. Under the above optimal conditions, the compressive strength of solidified stuff rises to 35 MPa, and water absorption is down to 4%-6%.Furthermore, when NaOH is applied as an additive in the process of solidification, the 2+concentrations of most heavy metals except Pb have reached the national leaching toxicity standard. The results of X-ray diffraction reveal that sulfured solidification is caused by the physical encapsulation rather than chemical transformation.

Jan 1, 2010

By Tsisana Gagnidze

A processing of technogenous wastes, which involve a gold-containing sulphide minerals, is a potential source to supplement the gold reserves. Hence, searching of ecologically safe and economically reasonable methods for processing of gold-containing technogenous wastes is a topical problem. To increase a parameters of gold extraction and to simplify a technology of the processing of above-mentioned wastes of sulphide minerals, an investigations have been carried out in the direction of the use of the method of electrochemical leaching without any preliminary processing of the mineral. It was established experimentally that an introduction of nitrogen containing organic additive into chloride solution favours to reduce a Red/Ox potential of the solution from 0,8÷1,2 V to 0,35÷0,5V, which permits to conduct the process of direct electrochemical leaching at ?soft? oxidation regimes at temperatures 20-300C C without an environmental contamination by molecular chlorine and with a high degree of a gold extraction up to 80-90%.

Jan 1, 2008

By S. Y. Tan

As CMOS devices are scaled down into nano-region, SiO2 dielectric is approaching its physical and electrical limits. High-k material has been investigated widely in recent years, and gate oxide take place growth oxide with Hf-based below 45nm gate length technology node has been shown. The phenomenon of interfacial property between bulk silicon and gate dielectric materials (HfO2 and HfSiO) was focused. A comparison of capacitance-voltage (C-V) characteristic of gate insulator was presented. Furthermore, the electrical property and thermal stability of high-k dielectric materials at various post deposit anneal (PDA) temperatures were established. The X-Ray diffraction technique was (XRD) utilized to analyze crystallization of the thin films, and the X-ray photoelectron spectroscopy (XPS) was applied for surface chemical bounding energy to identify the silicon and dielectric layers. Results show that HfSiO films have exhibited a superior performance on both thermal stability and electrical performance.

Jan 1, 2009

By Tianjiao Luo

The electroless copper plating process for continuous carbon fiber using CuSO4?5H2O as the main salt and formaldehyde as reducing agent was experimentally studied, including the effects of pH values and concentration of chelating agents, stabilizing agents and reducing agent on the electroless plating process. The surface morphology and the composition of coating were investigated by means of Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS), and deposited the coating thickness was measured by way of dissolution. The results indicated that the pretreatment of carbon fiber before plating was so important. This pretreatment could prevent the formation of the black cores, furthermore, it could form many active absorption cores with Ag as the center on the carbon fiber surface. Used the optimized parameters in this process, which led to a stable solution for plating, a homogeneous copper coating was conducted with the carbon fiber plated with favorable mechanical performance and high adhesion strength.

Jan 1, 2006

By X. J. Wu

Effects of various factors such as diaphragm materials, composition of electrolytes and current density on copper electrowinning from cupric chloride solutions was investigated. It is found that the crux of this process is to prevent the dissolution of copper by cupric ion and the formation of suspended CuCl precipitate. A process with high difference of copper concentrations between the feed solution and the spent electrolyte was selected. With this process, in which the feed solution contains 90 g/dm3 [Cu"], 3M NaC1, and 10mg/dm3 bone glue, and the spent electrolytes contains 10 g/dm3 [Cul, a very smooth and dense copper cathode can be produced with current efficiency above 93% and energy requirement less than 1.7 kwh/kg Cu at 25°C with N2 sparging. If a slightly higher energy requirement is permitted, smooth and dense copper cathodes can be produced at the current density up to 800 A/m2 with the identical solutions.

Jan 1, 1991

By Zhihong Liu

Monodisperse micron size nickel oxalate particles with rhombohedron morphology were prepared from condensed Ni(OH)2 suspension by a novel gel-sol process proposed by one of the authors. Firstly, condensed nickel hydroxide gel was formed by fast adding 1 mol dm-3 NaOH solution into 0.2 mol dm-3 nickel chloride solution, and then oxalic acid solution with a concentration of 0.25 mol dm-3 was dropped into the gel drop wise through a pump equiped with a pH controller under preset pH value, and in this process, Ni(OH)2 gel was converted gradually into monodisperse nickel oxalate sol. The formation of the nickel oxalate particles was found to proceed through a dissolution-recrystallization mechanism from the nickel hydroxide gel. The product particles exhibited rhombohedron like shape with micron size long axis and sub-micron size short axis. The effects of such factors, as temperature, surfactants, et al, were evaluated experimentally on the particles sizes and morphologies.

Jan 1, 2006

Sodium is added to aluminum-silicon eutectic alloys to modify the structure. The ideal amount is about 100 ppm but due to the fact that sodium is lighter than aluminum and can float to the surface where it bums, oxidizes ad volatilizes, a far greater amount is usually added. Furthermore, as the sodium is continually lost from the alloy the optimum amount is only present for a limited time. The net result is a process which is hard to control, produces fumes and a considerable amount of dross. It is shown that by electrochemically titrating sodium through a tube of sodium beta alumina electrolyte that the sodium can be added continuously in a controlled way. As the sodium is added to the bulk of the aluminum, there is no sodium on the surface of the alloy so that little surface oxidation occurs, and no fumes and dross are produced. This leads to an improved product and working conditions.

Jan 1, 1995

By Peter Willbrandt

Norddeutsche Affinerie's routes date back to the 18th century. NA was established in 1866 as a joint stock corporation. NA's core business covers the production of copper cathodes from primary and secondary raw materials and the processing of them into wire rod and shapes. Part of the shapes are processed into pre-rolled strip and shaped wires within the Group. With some 3,200 well qualified and highly motivated employees, the NA Group produces some 560,000 tonnes of copper cathodes, 370,000 tonnes of wire rod, 230,000 tonnes of shapes, 130,000 tonnes of pre-rolled strip as well as 70,00 tonnes of strips and shaped wires annually. NA's product range is complemented primarily by precious metals, selenium, sulphuric acid, lead and nickel sulphate. The paper will give an insight into the performance of NA and its business units with regard to production, environmental and health protection and occupational safety.

Jan 1, 2006

By Ashok D. Dalvi

Production of nickel from laterite ores has occurred for over 100 years beginning with processing of garnieritic ores from New Caledonia. However, until now the world nickel supply has been predominantly from sulfide sources. Going forward, the authors project that the production of nickel from sulfide ores will remain more or less constant. Most of the expansion in nickel production capacity over the next ten years will come from processing of laterite ores. Thus the capital and operating costs of new laterite projects will have significant impact on the nickel supply and therefore price. The authors have reviewed the history and capital and operating costs of various recent laterite projects and capital and operating costs of these projects and those "on the drawing board". The authors have also evaluated the risk associated with such projects. The paper will discuss the impact of this and the recent history on the future development of laterite nickel projects.

Jan 1, 2004

By J. W. Whitney

Itronics Inc., through its wholly owned subsidiary Itronics Metallurgical, Inc. (IMI), has successfully developed technology that allows it to be fully integrated as a photochemical recycler. IMI is now using this technology to expand its regional operation, which collects used photographic chemicals, chemically removes 99.997% of the silver and uses the residual to make a line of high quality liquid multinutrient liquid fertilizer products. Elevated silver discharges from the Reno-Sparks sewage treatment facility, that were traced back to incoming waste photographic chemicals and which were seriously impacting the sensitive fishery, provided the impetus for this project. This paper is updated from a paper presented at the Twenty-Second International Precious Metals Conference Toronto, Ontario, Canada in June 1998. It presents an overview of the scope of the problem solved by the technology, some of the permitting and development issues, and some of the specific fertilization formulations that are now being marketed.

Jan 1, 2000

By I. Sofia Fernandez del Rio

This paper describes a process for the treatment of the dusts generated during the operation of blast and reverberatory furnaces in the lead smelter, to remove zinc, cadmium, arsenic and halides from the circuit. The process consists of a Pefloles' developed leaching/purification stage and a solvent extraction process developed by Lurgi. The plant capacity is 5,000 tonnes Zn/year. The feed to solvent extraction contains 8 g/1 Zn. Impurities such as copper, iron, arsenic and cadmium are removed by conventional cementation processes. The cadmium product is 99.99 % pure. The solvent extraction process consists of two extraction stages, one washing stage and two stripping stages. D2EHPA is used as the extraction agent and 25% ammonia as the neutralizer. The rich-zinc solution is sent to the electrolytic zinc plant for zinc recovery. The raffinate produced, which is a mixture of ammonium sulfate and chloride, is used for agricultural applications.

Jan 1, 2000

By Corby Anderson

The efficient separation of palladium from the transition metals copper, nickel and iron can be effected by passing a leach solution of these metals through a column of the silica polyamine composite material, WP-1, patented by Purity Systems Inc (PSI), Assignee, University of Montana with exclusive license to PSI. The separation can be done at the intrinsic pH of a nitrogen species catalyzed (NSC) oxidative pressure leach solution (~0) and stripping of the palladium from the composite can be effected with hydrochloric acid/ammonium chloride solutions at 50oC. Batch capacities of the composite for palladium are ~ 1.8 mmol/g resin. The possibilities for isolating the metal from the strip are discussed. Given the proven longevity and rapid capture kinetics of the polyamine composites, this new approach should prove to be an economically viable alternative to the multi-step concentration processes practiced in the PGM industry to date.

Jan 1, 2003