Search Documents

By D. D. L. Chung

"In-situ network composites are composites in which the filler network is formed during composite fabrication, in contrast to ex-situ networks which are formed prior to composite fabrication. A homogeneous in-situ network composite has the entire network at the same composition; a heterogeneous in-situ network composite has different parts of the network at different compositions. The homogeneous network composite is made either by the Method of Molten Filler Flow or the Method of Dissolution and Deposition; a heterogeneous network composite is made by the Method of Liquid-Phase Networking. Examples include polymermatrix and metal-matrix composites.IntroductionNetwork composites refer to composites containing a continuous three-dimensional network as the filler. These composites are attractive in their lack of delamination failure, which is usually characterised by two-dimensional composites. The filler and matrix in a network composite can be considered two interpenetrating networks. The mechanical interlocking of the networks adds to the cohesion of the composite. In cases where the filer is much better than the matrix in a certain property, the network nature of the filler makes the filler highly effective in improving that property in the composite in all directions. The property desired in the composite may be high strength, high modulus, low coefficient of thermal expansion, high thermal conductivity, or low electrical resistivity."

Jan 1, 1994

By Rameshwar Sreenivasan

This paper presents a sustainability analysis of Selective Laser Sintering (SLS) from an energy standpoint. Data of electrical power consumed by the system over an entire build were acquired using a LabVIEW 8.6 circuit. The power drawn by individual subsystems was also measured, and an energy balance was performed. These data were then used to arrive at a Total Energy Indicator of the process with the help of a specific type of Environmental and Resource Management Data (ERMD) known as Eco- Indicators, which indicates the level of sustainability of the process.

Jan 1, 2010

A three?stages countercurrent fluidized bed prototipe reactor to neutralize the SO2from smelter gases has been developed. For gases with 8 vol-%SO2, at 800°C and for 4 h mean reaction time of the limestone, the capture of SO2 is 99%, with off gases with 0.07 vol-%. For 2 vol-%SO2, the total capture of SO2 can be obtained at 750°C and 4 h reaction time. The calcine obtained contain a blend of unreacted limestone and calcium sulphatewith minor amounts of residual lime.

Jan 1, 2006

By Sadegh Firoozi

Experiments measuring the kinetics of oxidation and making visual observations of the oxidation of approximately 6 g static lead baths containing arsenic, antimony and tin were conducted in the temperature range from 500 to 600 oC. A range of repeatable behaviours were observed, notably: the formation of a coherent, solid oxide layers on pure lead and lead-tin alloys; the formation of liquid oxide droplets during the initial oxidation of lead-arsenic and lead-antimony alloys and the eventual formation of a complete oxide layer covering the entire free surface of these alloys. Thermogravimetric measurements revealed that the rate of oxygen uptake was strongly influenced by the form of oxides being generated at the melt/gas interface. Compared to the rates of oxidation of pure lead, arsenic increased the rate of oxygen uptake throughout the temperature range via the formation of liquid oxidation products. The presence of antimony resulted in a moderate increase in the rate of oxygen uptake as compared to arsenic. Tin was effective in lowering the rate of oxidation even in the presence of arsenic because the oxidation product was always a coherent layer that acted as a physical barrier to oxygen transport to the underlying alloy.

Jan 1, 2006

By Art Cooper

Granulation systems are common in the metals industry. The process of granulating slags, mattes and metals is more than a century old, and a number of different systems have been developed to accomplish this task. These systems have followed an evolutionary path, and may be characterized by common elements in terms of molten material handling, granulation methods and post-granulation processing. This paper will summarize the more common systems used in the metals industry, with particular reference to non-ferrous applications.

Jan 1, 2006

By Takashi Ikeda, Masafumi Maeda

"Demand for solar cells is increasing linearly throughout the world. Last year production totaled 3000 tons worldwide. The market size of solar silicon is expected to increase further because of international ""political"" demand to reduce carbonaceous emission from energy consumed. Most elemental silicon is produced by the carbon reduction of Silica in an electric arc furnace. Purity of silicon at this stage is 90-99%. Major impurities are Fe, Ti, Ca· and Al, and minor ones are P, B and carbon. The oxidizing metallurgical process is no longer effective to remove transitfon metals because those are less noble to silicon. Nonmetallic impurities such as phosphorus and boron must be reduced to 0.001ppm for semiconductor use. The most common process for high purity silicon is the Siemens C process, which is basically distillation of hydro-chlorinated silicon followed by CVD of SiHCl3. The cost of such silicon is expensive to allow its popular use in solar cells. Currently scrap silicon -of semiconductors is used for this; however, the supply-of that scrap is limited to just a portion of semiconductor production.In this paper world demand for silicon will be reviewed and some of the processes proposed summarized.IntroductionSilicon is element 14 in atomic number and has an atomic weight of 28.0855. Little elemental silicon is found in the earth, and it is mostly found as oxides or silicate. The Clark number of silicon is very large and the second in its number. If we were discussing the volatility of silicon element on the globe, we would never worry about it. However, it is very difficult to obtain pure elemental silicon because a high purity silicon compound is very rare. In most cases these are silica (silicon oxide SiO2). As shown in Table 1, there are many grades of silica ore classified mainly by their content of iron and alumina."

Jan 1, 2000

By Marcio Toshio Tanaka, Marcelo Breda Mourao, Cyro Takano, Cesar Yuji Narita

"The concerns in questions related to the environmental impact in the steelmaking industries caused mainly on the gas emissions such as the dioxide carbon are due to its raw material such as the coal, a fossil and non renewable resource. The purpose of this paper is to replace from 10% to 50% of the coal used in cokemaking by mixing it with a renewable source (wood charcoal). The powder (- 325 mesh) from both raw materials (coal and wood charcoal) were mixed in order to obtain a briquette that was then heat treated at 1100°C to obtain the biocoke. Results of usual analysis (coke reactivity index, coke strength after reaction and cold crushing strength test) were employed to compare to regular coke briquettes. It was found that biocoke with different amounts of wood charcoal present features enabling it to be used in some ore reductionprocesses.1. IntroductionThe iron and steelmaking industry is a heavy emitter of carbon dioxide; according to the World Steel Association, 6.5% of global emissions of this greenhouse gas is due to the production of ferrous materials [ 1]. This is due to the fact that the fuel and reductant employed in the blast furnace is metallurgical coke, obtained from fossil coal. There are some projects aiming to reduce or even eliminate the emission of fossil GHG in the iron and steelmaking process [2]. Most of them propose the capture and storage of the gas (CCS) [3], a technology not yet proven. Other studies point out that the coke consumption in the blast furnace could be reduced by using high reactivity coke; this could lead to lower temperatures in the thermal reserve zone of the blast furnace and consequently less fuel rate in the furnace.The use of biomass in the iron ore reduction process is known as an environmentally accepted solution, as biomass does not release already fossilized carbon."

Jan 1, 2013

By Carl W. Dalrymple

A wide variety of contaminants (heavy metals, suspended solids, colloids, oils, organics) have been successfully removed from wastewater using an electrocoagulation process. An innovative electrocoagulation system is described. This process involves a procedure which subjects dissolved and suspended wastewater contaminants to the simultaneous addition of metal ions in the presence of direct current. During the treatment process Ionic and other charged particles in the wastewater are neutralized with oppositely charged ions generating the coagulation of contaminants: The process Is called CURE, and' presented here with application to wastewaters containing mainly heavy metals.

Jan 1, 1995

By Richard P. Roberts

This paper will discuss the methods for the cooling of aluminum melting furnace? dross .and their impact on the environment. Also discussed will be a case history of an AROS Dross Processor installation, which is designed to maximize the recovery of metal content of the dross in a manner which is not only environmentally cleaner, but which also prepares the output in such a way as to facilitate downstream processes. Handling of the discharged material will be discussed in regards to the recycling of the preserved metal content and deposition of the unusable-materials.

Jan 1, 1992

By Lakshman D. Jayaweera

Today's rapidly developing and changing technologies and industrial products and practices frequently carry with them the increased generation of materials that, if improperly dealt with, can threaten both public health and the environment. Mercury is an element that poses great problems in the many forms in which it is to be found in the mineral processing industry. These forms are often contained in hazardous wastes and residues which may be unstable, and in which the contained mercury has value. This paper presents some of the stabilisation and recovery methods which are based on hydrometallurgical techniques and thermodynamic stability considerations.

Jan 1, 1994

By I. U. Onyenanu, C. E. Ilochonwu, E. I. Nwonye, C. O. Nwajagu

This work shows how pure silica was derived directly from rice husks ash (RHA) in different temperatures for reduction to Silicon (Si). The processes to form Si materials are usually complex, costly and energy-intensive. The silica in the ash undergoes structural transformations depending on the conditions of combustion. A high purity silica was produced at 650oC after burning the rice husk (RH) for up to 7 hours. The purity of the silica was determined by dissolving the RHA with alkali solution to form sodium silicate solution of pH 11.0. This was added to hydrochloric acid of pH 1.5 which lowered the pH of the solution to 4.0 to form silica gels. The silica gels produced were washed and dried to powder and then characterized using XRD and EDX techniques. This study was done to reduce energy waste and environmental pollution in Nigeria as silica is used to develop many materials.

Jan 1, 2015

By R. G. Hilton

This paper deals with application of Super Detox? stabilization technology to the treatment of electric arc furnace dust (US-EPA listed hazardous waste KO61 ). The process has been used on approximately 170,000 tons of electric arc furnace dust. In addition to the nearly four years of commercial experience at Sterling, Illinois, the process is now being permitted for application at two other locations. The process was originally developed by the Bethlehem Steel Corporation and then further improved by Conversion Systems, Inc. (Bethlehem Steel's Licensee). The treatment process offers many unique bases for its selection, including: A) Low cost compared to the treatment alternatives; B) Lowest available TCLP leachate levels for any process treating K061. Many other processes leave some residue that represents a disposal requirement, although often not addressed; C) Produces minimized final waste disposed, including the fact that the total volume of dust generated and less than the volume occupied by the residue slag from HTMR; and, D) Opportunities for the beneficial utilization of part or all of the waste stream through the development of chemical and physical characteristics. Each of these aspects will be specifically discussed in the paper, including that status of the operations now under permit.

Jan 1, 1994

By Alessandro Blasi, Massimo Morgana, Corradino Sposato, Pietro Garzone, Giuseppe Devincenzis

The rare earth elements are essential for a diverse and expanding array of high-technology applications, which constitute an important part of the industrial economy of the 21st century. As a matter of fact, rare earth has been listed in the category of strategic elements in many countries becoming a core business for international research. Experimental tests have been carried out on a bench scale battery of mixer settler composed of 24 stages, each one with a volume of 150 ml. These trials have been performed at room temperature checked by a micro-climatic control system. The battery was setted in two sections: extraction and scrubbing section. Rare earths concentrations were obtained by ICP-OES analysis made on aqueous phase and on the stripped from organic phase. We obtained a complete separation of light rare earth (La, Ce, Pr, Nd) in two sub-groups: La/Ce and Pr/Nd.

Jan 1, 2014

By G. L. Pedroti

With the development of industrial processes and the consequent emergence of numerous products that quickly become necessities, industrial activity has acquired an essential character today. Although its importance is unquestionable, industrial activity is responsible for generating quite a large number of residues, with different shapes and characteristics. It has been observed, in particular the grits (Kraft process in the cellulose industry) and the residue from the processing of granite. And, given the importance of Portland cement as a building material, its vast employment and waste properties that resemble components of the clinker, it was decided to produce cementitious compounds from these industrial wastes. The residues were subjected to mineralogical, chemical, physical and morphological. And, the mixing ratio between the residues in the 70% and 30% grits residue granite was sintered at 1250 ° C furnaces to burn threshold of 6 hours forming new compounds observing tri-calcium aluminate and di-calcium silicate that are compounds found in portland cement.

Jan 1, 2015

By C. M. F. Viera

In this work the properties of a clayey ceramic incorporated, up to 10 wt.%, with three types of wastes from a water treatment plant was evaluated. To determine the physical and mechanical properties such as linear shrinkage, water absorption and diametrical compression, specimens were prepared by 18 MPa uniaxial pressure and then fired in laboratory furnace at 700oC. The results indicated that the wastes incorporation changed the properties of the clayey ceramic. From the results it was found it possible to recycle these wastes into clayey ceramic in low amounts to avoid deleterious effect on the quality of the fired product.

Jan 1, 2008

By Zemin Ma

A novel chromate [Cr(VI)] reducing bacterium was isolated from chromite ore processing residue disposal site of China and identified as a Leucobacter sp. by 16S rRNA gene sequence homology. The minimum inhibitory concentration of strain CRB1 was 820 mg l-1 of Cr(VI). The reduction of Cr(VI) occurred only under aerobic conditions. With an initial concentration of 2.5×108 cells ml-1, 1800 mg l-1 of Cr(VI) was reduced entirely within 38 h under the optimum conditions, at 30 °C and pH 9.0. Increasing Cr(VI) concentrations prolonged reduction process and higher cell densities meant quicker reduction. A blue precipitate was produced during chromate reduction of strain CRB1, which was binding to the surface of bacterial cells and determined as trivalent chromium with electron paramagnetic resonance (EPR) spectrometry. The conspicuous chromate reduction ability of Leucobacter sp. CRB1 suggested a potential for bioremediation of Cr(VI) containing wastes.

Jan 1, 2008

By Muammer Kaya

The purpose of this review is to raise awareness about e-waste problem in the World. Whether generated at our home or our office, e-waste is most rapidly growing waste problem in the world. Even though there are conventional disposal methods (such as landfill and incineration) for e-waste, these methods have both economic and environmental disadvantages; recycling is a new waste management option which diverts end-of-life (EOL) electrical and electronic equipment (EEE) from landfill and incineration [1, 2]. Successful diversion strategy must be based on economic sustainability, technical feasibility and social support [3]. Recycling infrastructure includes transportation, collection, recovery and resale establishments. The first part of this paper describes the e-waste facts, how big is the e-waste problem and existing recycling programmes and collecting methods in the USA and EU; second part, describes various methods available to recover valuable materials (glass, plastic and metals (Pb, Cu, Al, Steel, Ni, Au, Pd, Cu etc)) in e-waste for a safe and environmental friendly disposal

Jan 1, 2009

By Zhigang Liang

Investigation into the mixing of 150t ladle furnace by two-nozzle jetting was performed by a water model simulation of 1:4. The effects of nozzle arrangements including separation angle, radial position and asymmetry as well as tracer adding position on the mixing time were studied. The most favorable mixing is achieved when the two nozzles are symmetrically arranged at half radii in the ladle, with 45o separation angle. The empirical relationship between the mixing time and stirring power intensity has been established for two-nozzle jetting based on the present experimental results. In addition, the swelling above bath surface is also investigated with two-nozzle jetting.

Jan 1, 2009

By Qingzhu Li

The brewing industry byproduct, spent grain (SG), was evaluated for its ability to adsorb Ag(I) from aqueous solutions. Ag(I) adsorption was dependent on solution pH, contact time, adsorbent dose, initial Ag(I) concentration and temperature. The kinetic data were well described by pseudo-second-order kinetic model, indicating that chemical adsorption was the rate-controlling step. The equilibrium data followed Freundlich isotherm rather than Langmuir isotherm, suggesting heterogenity of the adsorption sites on spent grain. Ag(I) desorbed from Ag(I)-loaded spent grain was also evaluated in this study. HCl, NaOH, Na2S2O3 and ultrapure water were chosen as eluants and desorbed Ag(I)-loaded spent grain for 30min, Ag(I)-loaded spent grain desorbed in 0.1M Na2S2O3 exhibited higher elution efficiency as compared with other eluants. The results indicated that application of spent grain for adsorption and recovery of silver from aqueous solutions was feasible.

Jan 1, 2009

By Yunnen Chen

The test and use of natural materials as biosorbents for the removal of heavy metals from industrial wastewater is under constant development. In the present study, the biosorption capacity of waste microzyme was studied for cadmium The cadmium removal study has been carried out batchwise where the influence of physico-chemical key parameters such as pH value of solution, contacting time and initial cadmium ions concentration have been considered. The influence of metal ion concentration was evaluated and the results were fitted using adsorption isotherm models. The kinetic of cadmium biosorption was also investigated. The maximum percent removal was attained at the pH 7.0 after about 30 min. Waste microzyme was a potential biosorbent for the removal of Cd(II) from the effluent of electroplating industry.

Jan 1, 2009