Search Documents

By Steven M. Puricelli

Sulfuric acid plants associated with smelters, have historically been an overworked and often neglected pollution control device. They could do little more than manage the wide fluctuations in gas flow and SO2 strength from the smelter. With the introduction of flash smelting, the picture began to change, but the fluctuating batch converters continued to dictate acid plant design. More recently, the commercial use of continuous converting processes utilizing high levels of oxygen enrichment has dramatically upgraded the SO2 strength and stabilized the gas flow to the acid plant. The SO2 gas now issues continuously and at concentrations that allow for compact and, cost effective acid plants. Relieved of the burden of excessive dilution air, the heats of reaction can also be recovered as medium pressure steam and used to drive a generator, making the acid plant a net producer of power and a valuable asset to balance sheets. This concept was put into practice at the Kennecott Utah Copper Corporation smelter modernization project, located in Salt Lake City, Utah. The new acid plant, which was commissioned in June of 1995, is a sophisticated, low environmental impact, energy producing plant, worthy of review. This paper examines the key features of this acid plant, such as controlling its tail gas, by catalysis alone, to an environmentally friendly, 100 ppm of SO2, while feeding the acid plant converter with an efficient 14% SO2. The acid plant is also a prudent steward of energy resources, recovering 220,000 lb/hr of 140 psig steam from process heat which is used to generate a substantial 20 MW of gross power. Also discussed will be some of the ongoing issues, such as handling of selenium and fluorine in the gas cleaning sections, as well as a review of some. of the problems that were identified and resolved. Today's modem acid plants, by necessity, are becoming a producer of quality, valuable products, making the acid plant an asset and not a liability. Plants like Kennecott are already gaining wider acceptance and are expected to be the vision of the future.

Jan 1, 1998

By Carla Lupi

Zinc electrowinning from sulfate solutions is the traditional industrial method to produce SHG zinc. Over the past few years several efforts have been done to improve process efficiency in order to reach high productivity with low energy requirement. The latter aim can be pursued both by means of a hard purification of the electrolyte and reducing the anodic voltage. This work is a comparative study of the results obtained in several previous researches on zinc electrowinning from both sulfate and chloride solutions. Zinc electrowinning tests on industrial sulfate solution have been carried out by using Pb alloy anodes and by adding organic depolarizers such as ethanol, acetic acid or ethylene glycol. Experiments on chloride solutions, obtained by purification of zinc exhausted electrolyte, have been performed by using DSA anodes and by testing the effect of additives such as TEACI and TBAC\. Comparing the best results obtained with the two methods it can be highlighted that a high quality zinc is electrowon in both cases with comparable energy requirements.

Jan 1, 2000

By Qiang Guo, Zongliang Zuo, Mengqi Wei, Qingbo Yu, Qin Qin

Activated carbons, derived from waste ion-exchange resin by CO2 physical activation, were applied to separate CO2 from flue gas against global warming. The BET specific surface areas of activated carbons at different activation temperatures and times were investigated. The CO2 adsorption capacity was tested under non-isothermal and isothermal conditions. The experimental results show that when keeping the activation temperature constant, the specific surface area increases firstly and then decreases with increasing activation time. For the given activation time, the specific surface area rises firstly and then declines with increasing activation temperature. The adsorption capacity decreases with increasing temperature. The maximum adsorption capacity is 51.46 mg/g under the condition of 298 K and pure CO2. Fractional order kinetic model is the best one to describe the kinetics of CO2 adsorption. The activated carbons show the potential to be an effective adsorbent for the removal of CO2 from flue gas.

Mar 1, 2018

By Carl C. Nesbitt

A study was conducted to examine the treatment of metal-bearing effluents by precipitating the metals as sulfides and simultaneously collecting the particles by flotation. The precipitant was hydrogen sulfide gas which was introduced into a bench-scale column cell with air. The study included experiments of various flotation reagents and column configurations in treating solutions containing dissolved copper, lead, mercury, iron, zinc and cadmium. An acidic laboratory waste from a local copper operation was used to test the column with a solution containing several metals and arsenic. Precipitates were observed to form at the gas/liquid interface when the gas mixtures were rich in H2S. Copper, mercury, lead, and cadmium were precipitated from solution as sulfides to concentrations near detection limits. The flotation of these precipitates was enhanced with small amounts of S-7151 promoter from American Cyanamide Company and Dowfroth 1263 mixed with the feed. The recovery of the precipitates in this manner produced a smaller volume slurry which was easier to dewatering than a slurry produced by conventional precipitation techniques. The low pH and high oxidation-reduction potential in the cell from H2S addition was not conducive to form precipitates of iron, zinc or arsenic. However, these ions were precipitated as sulfides by raising the pH of the column discharge.

Jan 1, 1994

By Yamei Han, Jiang Du, Jinhui Peng, Mengbi Fu, Libo Zhang, Zhengfu Zhang

"A continuously pilot synthesis by microwave-heating was used in preparing the cathode material LiNi113Co113Mn11302 for Li-ion battery, which used Ni1/3Co1/3Mn1/3(0H)2 and LizC03 as raw materials. Decomposition of the raw materials and synthesis of LixNi113Co113Mn11302 would be fmished in single roasting process. In addition, using microwave-heating would reduce the reacting time largely. Furthermore, the yield of LixNi1/3Co1/3Mn1/302 synthetized in single roasting process was 50 kg. Meanwhile, the effects of Li:(Ni+Co+Mn) molar radio (Li:(Ni+Co+Mn)=l.06, 1.075, 1.09, 1.15) was studied in this paper. XRD, SEM and EIS were used in characterizing the cathode material. The results showed that the best Li:(Ni+Co+Mn) molar radio was 1.075. It was found that the LiNi113Co113Mn11302 synthetized with Li:(Ni+Co+Mn)=l.075 had homogenous distribution of particles and ideal layered structure. The galvanostatic charge-discharge(O. l C, 2. 75-4.3V, vs. Lt /Li) tests showed that the initial discharge capacity of the LixNi113Co113Mn11302 was 159.5mAh·g-1, and the discharge capacity was 157.6mAh·g·1after10 cycles.IntroductionRecently, as the cobalt was expensive and the restriction of dynamic power, the commercial cathode Li2Co02 which was expensive, toxic, and high pollution had exposed its defects[1·2l. Since T.Ohzuku[3l first reported the layered LiNi113Co113Mn11302, this material had high reversible capacity and caused the attentions of researchers[4l. Its reversible capacity was l 60mAh/g and 200mAh/g in the voltage range of 2.75-4.3V[5-61. But for the present, preparing LiNiwCowMnw02 by traditional had lots of disadvantages, such as the long heating time, the high cost and the volatizing of lithium and so on[7-9l. According to these, traditional prepatation wasn't good for sustainable development and energy conservation."

Jan 1, 2013

By Wade L. Karlsen

"Revision surgery to replace joints in the human body requires materials that are strong, long-lasting, and biocompatible. Metallic implants made of cobalt-chromium-molybdenum alloys are already popular because of their proven corrosion and wear resistance properties, but there is an on-going effort to economically improve their performance. Alloying with inert nitrogen can enhance the mechanical properties of the alloy, enhance its corrosion resistance, and elevate the temperature at which the metallic implants can be thermally treated, without increasing the threat to the human body. The current work has produced a high-nitrogen Co-Cr-Mo alloy through HIP consolidation of metal powders that have undergone nitriding in a mechanically fluidized bed. The already fine microstructure of the powders combined with the increased nitrogen content resulted in significant property gains in the consolidated materials.IntroductionMetallic implants made of cobalt-chromium-molybdenum alloys are already popular because of their proven corrosion and wear resistance properties, but there is an ongoing effort to improve their performance. Research on a Stellite 21 cobalt-chromiummolybdenum alloy has shown that nitrogen alloying can be desirable from several standpoints [l]. Firstly, it has indicated that nitrogen can enhance the mechanical properties of the alloy, which could allow more demanding implant designs. The same work also demonstrated that nitrogen can elevate the temperature at which the metallic implants can be thermally treated, which is desirable in situations in which surface textures are to be sintered to the implant to enhance its fixation properties. Finally, that research work discovered that, not only does nitrogen not harm the corrosion resistance of the cobalt-chromium-molybdenum alloys, but it may in fact enhance it. Combining this with the fact that small amounts of nitrogen are not considered a threat to the human body, makes nitrogen alloying an attractive alternative for enhancing the properties of Co-Cr-Mo."

Jan 1, 2000

By Y. Kumagai, F. A. Souza

"Electroless plating process has been used in many fields such as automobile and electronic industries. Solutions used in these processes must be disposed or treated. Commonly, in these solutions metal ions, organic materials and others chemicals are in very high concentration. It is very difficult to keep the environmental regulations for disposal of these materials, and the cost of the plating process becomes higher.The objective of this study was to investigate the recovery of components of those baths in order to decrease the cost of the plating process as well as to meet the environmental regulation.In this study the recovery metal ions, sulfate ions, phosphite ions and organic compounds were investigated. Organic compounds used in electroless plating solutions are the organic acids. In this work the solvent extraction of the most used organic acids included citric, lactic, succinic, tartaric and malic was studied. The solvent phase considered in these studies was ethyl acetate.About 95% of the metal ion was recovered by chemical plating onto mica powder. The hypophosphite remained is oxidized to phosphite and with the sulfate ion, both are recovered as calcium salts by selective precipitation in pH 7 and 2 respectively. Organic acids were recovered by solvent extraction using ethyl acetate as solvent phase and the best results were for lactic acid and succinic acid.Along with this study, was developed the analytical parameters to perform wastewater analysis by using Ion Chromatography, High Performance Liquid Chromatography (HPLC), Fourrier Transform Infrared Spectroscopy (FTIR). Ion chromatography was used to perform analysis of sulfate and phosphite ions in liquid matrix, HPLC was used to perform analysis of organic acids in liquid matrix and FTIR was used for characterization of the solids obtained in the recovery processes."

Jan 1, 1997

By C. J. Newman

Prior to 1995, the smelting process at the Kennecott Utah Copper Corporation (KUCC) smelter consisted of Noranda reactors and Pierce-Smith converters. In the consideration of expansion opportunities, the existing process did not lend itself to a program geared towards processing the total output of KUCC mining and milling operations. During 1989 and 1990, a number of smelting options were evaluated. The final selection was the Outokumpu flash smelting process, coupled with the new Kennecott-Outokumpu flash converting technology. Facilities were designed and installed to process 1:0 million tonnes per year of copper concentrate, with the ability to expand to 1.2 million tonnes per year. Following the shutdown of the smelter facility utilizing the Noranda technology in May 1995, the flash smelting, furnace commenced operation in June with the flash converting furnace startup following a few weeks later. The smelter has achieved design production targets and environmental goals. Current operating rates are at or above design rates for concentrate and matte processing. Emissions are lower than the permit levels and equate to less than 3.5 kg of SO2 per tonne of copper. This paper outlines the design, construction, startup and the first two years of operation of the modernized KUCC smelter.

Jan 1, 1998

By Sayan Sarkar

HAMR (Hydrogen Assisted Magnesiothermic Reduction) process is a promising alternative route of titanium production, which is convenient due to reduction at relatively lower temperatures below 750 °C and usage of cost-efficient TiO2 as the starting material. A crucial step involved in this process requires the Mg reduction of TiO2 subjected to H2 atmosphere which produces porous TiH2 along with residual magnesium impurities. Before the final heat treatment and deoxygenation steps for consolidation of the Ti powder, leaching plays a significant role in the removal of Mg impurities. In this report, we present a systematic study on the role of acid concentration (HCl), temperature and the kinetics of MgO dissolution. In addition, we also report the controlling mechanism during kinetics of MgO dissolution in acid. This parametric study will provide a platform to ensure very low Mg content that meets with ASTM standards during production of Ti in the HAMR process.

By David G. Dixon

Although the kinetics of leaching processes are of paramount importance in the design and analysis of nearly all hydrometallurgical flowsheets, these concepts remain poorly understood and, as a result, are only rarely applied to mass and heat balance models. In this second of two papers, we demonstrate how simple yet powerful models of leaching kinetics and other rate processes may be added to mass and heat balance models, and apply these concepts using a spreadsheet model of a simplified pyrite autoclaving flowsheet. In particular, we focus on the interpretation and scale-up of batch leaching data, and on simple means for modeling other phenomena commonly associated with leaching, such as reagent depletion, gas-liquid mixing, and the precipitation of oxides and basic salts.

Jan 1, 2002

By Bo Björkman

Four different arsenic containing dusts from the Boliden plant, Boliden mineral AB, Sweden have been examined. A kinetic study of the As elimination was performed in a laboratory scale roasting furnace for roasting furnace ESP dust and smelting furnace ESP dust. Characterisation and thermodynamic calculations were carried out to determine the mineralogy, and the stability of compounds in the dusts studied. The characterisation methods used were chemical analysis, X-ray diffraction analysis and microprobe analysis. It was found in the experiments that a high degree of As elimination was obtained for roasting fumace ESP dust and a low degree for smelting fumace ESP dust. Derived kinetic models are given. A prediction of the As-elimation for settling furnace dust and converter ventilation dust is presented.

Jan 1, 1994

By Li Xi

This paper describes how a back-propagation neural network is built for predicting the properties of engineering materials from their other properties, compositions or processes. A predicted result of the impact toughness of a 12Cr-2Ni-1.5Mo stainless steel from its tempering temperature is presented. Furthermore, the combination of this neural network for prediction is able to supplement the unpredictability of the expert system outside its domain of expertise. An integrated system may perform more intelligently and solve more complex problems as well as human expert, in some case even better.

Jan 1, 1992

By Tapani Järvinen

Non-ferrous metals and metals in general are considered as being non-renewable natural resources. Metals are needed because of their excellent and irreplaceable properties. The consumption of metals, with the exception of carbon steel, is steadily growing by 1-3 % annually, and that of stainless steel as much as 3-6 %. This is a general trend, which is periodically disturbed by cyclical variations. In recent years so-called "New Economy" has become prominent in the public media and the market value of the traditional industry has been well below its real value and importance. Nevertheless, the modem society requires metals today and also in the future, and the companies using the most modem technology in a responsible way and innovative solutions not only in technology, but also in everything they do will survive. This paper describes the role of Europe as a producer of primary base metals and as a supplier of technologies in the base metals industry. It concentrates on the development and commercialization of technologies and project implementation in the metallurgical industry. As one example of a European approach to these matters the paper presents Outokumpu' s response to the future challenges in the base metals industry. Outokumpu Oyj is one of the leading metals and technology companies in the world of stainless steel, copper, zinc, and sales of technology in metals and minerals businesses. Outokumpu applies its knowledge of metals and processing to generate value for its customers and shareholder. Everything we do, we do in an economically, environmentally and socially responsible way.

Jan 1, 2003

By Xiaojie Gao, Shufeng Yang, Jingshe Li, Chengsong Liu

In the blast furnace process, the dust entrained in the blast furnace gas enters into the down-comer, flows through the gravity dust separator (to eliminate coarse particles) and then is collected in a bag-house. The powder collected by the baghouse is called bag dust, while both fractions are called blast furnace dust whose main components are C and Fe. The dust also contains small amounts of nonferrous metals such as Zn and Pb, which have some value. Also, due to the small particle size and low density the dust is easily suspended in air and so can endanger human health. Therefore it is necessary to develop a process to both treat the dust to recover the metal values and to dispose of the residue – preferably by recycling to the blast furnace itself via the sinter strand. These objectives will result in good economic, environmental and social benefits [1].

Jan 1, 2014

By N. A. Barcza

DC plasma-arc technology using a hollow graphite electrode (cathode) has been successfully implemented in the primary metallurgical industry in South Africa up to the 30 MW scale. Mintek has applied its expertise base, established over the past fifteen years, to testing the treatment of metallurgical wastes such as carbon- and stainless-steel plant dusts, lead- and zinc-containing slags, and residues from the base-metal industry. Favourable results have been achieved, and disposable products were produced. The evaluation of numerous wastes indicates that recovery of zinc as metal gives the best economic return from these sources. Direct recovery via a splash condenser or electrolytic zinc extraction from fume are the two preferred alternatives under review. In both instances dehalogenation is an important issue, but can be achieved by suitable treatment processes. The Enviroplas technology provides a flexible, commercially viable approach to the treatment of a wide variety of wastes. Mintek, together with its associate Pyromet CC, are installing a plasma- arc pilot-plant facility with both an ISP lead-splash condenser of about 5 t/d condensed zinc capacity and a combustion chamber to burn zinc vapour to zinc oxide. This will demonstrate the suitability of the Enviroplas technology for treating specific metallurgical wastes, so that customized industrial plants can be engineered based on large-scale testwork.

Jan 1, 1994

By Djona M. Gaballah I.

Selective chlorination of unroasted and roasted spent hydrorefming catalysts was studied between 300 and 600°C using the following gas mixtures : C12+CO, C12+N2 and CI2+air. Such materials contain Co, Ni and Mo compounds supported by alumina and/ or silica. They also contain variable amounts of V compounds, C, S, etc., accumulated during the life time of the catalyst. Direct oxychlorination of the C+S rich sample allows higher extraction rates than those obtained by the carbochlorination of the same roasted one. It seems that the roasting step doesn't favor the economic metals' recovery. Results of the chlorination of C+S poor spent catalysts, in the presence of CO, in the chlorinating gas mixture, or of carbon added to the sample, were comparable. Cobalt and nickel chlorides were .extracted from the chlorination residues by their dissolution with acidified water, whereas molybdenum and vanadium chlorinated compounds were recovered by selective condensation from the vapor phase. The recovery rates of valuable metals as well as the selectivity were higher for the chlorination of spent catalysts than results obtained by the hydrometallurgical processing of the same sample. Results of the scale-up of the oxychlorination of the unroasted sample confirmed those of the laboratory scale. The global recovery rates were about 88 pct of cobalt, 93 pct of molybdenum and 76 pct of vanadium. The carbochlorination was applied to the recovery of W and Ti from Denox catalyst that is a carbon and sulfur free one. Recovery rates higher than 99 pct at temperatures lower than 500 °C could be obtained. This may indicate that the chlorination process can be applied to the treatment of various industrial wastes or by-product containing transition and/or refractory metal compounds A flow - sheet for the pretreatment of these materials is proposed.

Jan 1, 1995

By Mark E. Schlesinger

Engineering design follows a six–step sequence. Demonstration of this sequence in materials engineering is less common. A case study is presented, using the 1989 paper by Gafner on the development of 990 gold-titanium alloy. This paper identifies a need, develops the problem, identifies alternatives, demonstrates the use of metallurgical principles to identify alternative responses, and shows how more favorable options are selected. The paper can also be used to illustrate engineering design as an iterative process. The paper is also useful as a starting point for more in-depth examination of specific elements of the design process, and lends itself to the creation of student exercises.

Jan 1, 2014

By Ma Lijuan, Zhang Yubing, Wang Bo, Sun Huilan

The effect of lime ratio on phase composition and alumina leaching property of MgO-contained calcium aluminate clinker were investigated by analytical reagent, the XRD analysis of its mechanism was discussed. The results showed that: when the sintering temperature was 1350 ℃, C/A was 1.4, A/S was 1.3 and the content of MgO was 4%, the increase of the C/A promoted the formation of C12A7 and restrained the formation of Q-phase. The alumina-leaching ratio of the clinker (A/S was 1.3) was increased from 74.33% to 91.34% when the content of CaO was 5.21%.

Jan 1, 2015

By Jafar Safarian, Gabriella Tranell, Stine Espelien

Hydrometallurgical treatment of silicon is an effective process for the removal of metallic impurities for producing solar grade silicon feedstock. In the present research, the removal of impurities from silicon is studied through the addition of Mg into a commercial silicon, its solidi fication, and acid leaching. The effect of concentration of HCl, temperature and leaching duration on the removal of impurities are studied. It is shown that the impurities such as P, Fe, Al, Ti, Ca, …are effectively removed through the applied method and Mg improves the segregation and the removal of the impurities. Scanning electron microscopy examination of the samples indicates the disintegration and dissolution of Mg2Si phase in acid leaching which causes the chemical and physical removal of the impurities existing in the phases between the silicon grains. It is shown that the leaching process rate can be optimized through the control of the acid leaching conditions.

Mar 1, 2017

By Roberto Parreiras Tavares, Frederico da Costa Fernandes, Guilherme Antonio Defendi, Vangleik Ferreira da Cruz, Júlio César de Sousa Pena

"Near-net-shape casting is an important area of research in the iron and steel industry today. Among the near-net-shape casting processes, the single-belt caster seems to be the most promising, since it is the only one that can achieve levels of productivity similar to those obtained with conventional continuous casting machines. One of the most important aspects in the single-belt casting is the feeding system used to deliver liquid metal over the belt. This system determines the velocity distribution and the levels of turbulence of the liquid metal and affects the quality of the strips. In the present work, a metal delivery system having a simple geometry was proposed. Using the CFD code CFX 5.6, a mathematical model to simulate three-dimensional turbulent fluid flow and heat transfer in that system has been developed. This model was used to analyze different configurations of the metal delivery system and the free surface shape of the fluid was also determined. A physical model of the feeding system was built and used to validate the predictions of the mathematical model. The fluid flow calculations have been validated by dye injection experiments and laser doppler anemometry. Measurements of the free surface levels have also been performed. These experiments provided supporting evidence for the predictions of the mathematical model.IntroductionTo maintain its competitiveness in the present market, the metallurgical sector, particularly the steelmaking companies, are developing new techniques of production. Some of these new processes are focussed on the strip casting technologies. Among these technologies, the SingleBelt process is considered the most interesting option, reducing the number of rolling steps and, consequently, the final cost of the product, especially the part associated to the energy consumption (fuel and/or electric energy). This process can also reach levels of productivity that can not be matched by other strip casting methods(1). One of the most important aspects concerning these new processes is related to the liquid metal delivery system. This system can have a significant effect on the final quality of the strips, since it determines the velocity distribution and the levels of turbulence of the liquid metal."

Jan 1, 2004