Search Documents

By Ting Liu, Qian Li, Peng Deng

The wastewater containing Hg2+ and Pb2+ does great harm to the environment and human bodies. Traditional wastewater treatment cannot fundamentally put a stop to heavy metals pollution for producing secondary pollution. In this paper, Hg2+ and Pb2+ in wastewater were removed and recovered by sulfide precipitation- flotation. Sodium sulfide was used as precipitant and butyl ammonium aerofloat was used as collector. Results indicated that Hg2+ and Pb2+ could be reduce to less than 0.03mg/L and 0.16mg/L respectively by both coprecipitation- floatation and fractional precipitation- floatation. In these two methods, fractional precipitation flotation could not only remove Hg2+ and Pb2+ from wastewater, but also could recover mercury and lead effectively. The infrared spectrograms showed that the adsorption between butyl ammonium aerofloat and mercury precipitate or lead precipitate is chemisorption.

Jan 1, 2015

By A. V. Kuznetsov, R. I. Kamkin, V. M. Paretskiy, A. Y. Mamaev, V. P. Bystrov, A. S. Vernigora

"Vanukov furnace technology is an efficient, proven pyrometallurgical injection technology, used extensively in Russia and Kazakhstan for a number of different applications. The technology was most widely adopted for processing copper sulfide concentrates for matte in smelters in Norilsk, Revda (Russia) and Balkhash (Kazakhstan). The following applications also were developed and tested at industrial scale: treatment of sulfide lead and lead-zinc concentrates, laterite nickel ore, production of cast iron, treatment of antimony gold-containing ores, and municipal solid waste. In this paper, current experience of Vanukov furnace application to these technologies is described with a number of general development trends and new areas of application.IntroductionAt the present time, the Vanukov process, developed at the Moscow State Institute of Steel and Alloys at the Department of metallurgy of non-ferrous, rare and noble metals with collaboration with other research organizations, is a highly efficient technological solution for processing different kinds of raw materials. The process was invented by Professor Andrey Vladimirovich Vanukov, whose research work began in 1949. From 1956 to 1975 test runs of the technology were carried out at the smelters in Norilsk and Balkhash. In 1976 a pilot Vanukov furnace was built in Ryazan. Furnace designs was modified to suit the various test programs. A major objective of each experiment was the determination of optimal working conditions for processing different types of raw materials such as copper, copper-nickel, copper-zinc, lead or pyrite concentrates, and materials containing secondary lead and zinc. After the death of Andrey Vladimirovich Vanukov in 1986, this technology and furnaces based on the technology were named after him: “Vanukov process” and “Vanukov furnace”. Today, the following furnaces based on Vanukov technology are either working or were tested at semi-industrial scale: three in Norilsk, two in Revda (Russia) and two in Balkhash (Kazakhstan) for treatment of copper sulfide concentrates for matte, one in Orsk (Russia) for processing laterite nickel ore, one in the Buruktal plant (Russia) for antimony gold-containing ores for antimony oxide sublimates and gold-containing metallic antimony, and one in China for processing sulfide lead and lead-zinc concentrates for production of black lead and zinc-containing sublimates."

Jan 1, 2011

By Donald P. Ziegler, James F. Klausner, Srinivas S. Garimella

"By 2015, nearly half the world's population will live in ""water stressed"" areas. Production of fresh water utilizing waste heat from industrial processes has been identified globally as a research priority.About 15% of the electricity required to produce aluminum is lost as waste heat in the off-gas. However, the low temperature (low grade) of the heat limits reuse. The off-gases contain 50-150 ppm SO2 ; tightening regulations coupled with increasing coke sulfur levels are motivating SO2 control, for which seawater scrubbing is attractive for smelters with suitable access.We describe a process that produces fresh water, utilizing the waste heat while scrubbing SO2 . It uses direct contact between seawater and off-gas to humidify the off-gas. The vapor is subsequently condensed. In smelter trials, a unit treating a slip stream produced high quality water in the anticipated quantity, attaining over 95% SO2 scrubbing. Future work involves scaling the process to be economically attractive.BackgroundPopulation growth, coupled with industrialization and urbanization, are increasing demand for water. Water scarcity already affects every continent. Around 1.2 billion people, or almost one-fifth of the world's population, live in areas of water scarcity, and 500 million people are approaching this situation. By 2025, 1.8 billion people will be living in countries or regions with absolute water scarcity, and two-thirds of the world's population could be living under water stressed conditions (< 1,700 m3 per person annually) [1]. An assessment by the U.S. General Accounting Office revealed that under normal conditions, by 2013, water managers in 36 states in the USA anticipate water shortages, and that the number might grow to 46 states under drought conditions [2].The obvious choice to alleviate water scarcity is the 97% of available water in the oceans, which is saline and requires desalination for use in biological, agricultural and industrial applications. Technologies developed for desalination include Thermal Distillation, Reverse Osmosis (RO), Electro-Dialysis, and Vacuum Freezing. Distillation and RO are the most commercially prominent. Thermal distillation technologies include Multiple Effect Distillation (MED) and Multi-Stage Flashing (MSF). The report commissioned by the World Bank [3] is one of the many excellent references on desalination technologies. According to the International Desalination Association working paper [4], there were more than 17,348 industrial scale desalination plants installed or contracted by 2004. The total production from these plants is on the order of 8.3 billion imperial gallons per day. RO provides 47.2% of the total capacity. The leading thermal process, MSF, provides 36.5% of the total capacity. Although MSF and RO technologies currently provide the most cost effective means for desalination, their drawback is that they are very energy intensive, and whether or not they remain cost effective strongly depends on energy prices and energy supply."

Jan 1, 2012

By Yutaka Shiraishi

Two methods were developed to measure the viscosity of the slag from the glassy to the liquid states in an ascending temperature process. The first method employs rotating parallel plates within which is placed a solid cylindrical sample in line with a sphere. The second method uses a tube which is pushed into a sample held in a rotating crucible. Both methods were tested using standard glasses, including boron trioxide and NBS standard glass #711. The main difference between these two methods is in sample preparation. Comparative measurements between two methods were performed using a sodium boro-disilicate glass containing 5%mol of alumina. The results showed good agreement in the mid-range of glassy viscosities, 105 to to7 Pa.s. In the liquid state, there were no significant differences between the two methods.

Jan 1, 2003

By Yutaka Shiraishi

Two methods were developed to measure the viscosity of the slag from the glassy to the liquid states in an ascending temperature process. The first method employs rotating parallel plates within which is placed a solid cylindrical sample in line with a sphere. The second method uses a tube which is pushed into a sample held in a rotating crucible. Both methods were tested using standard glasses, including boron trioxide and NBS standard glass #711. The main difference between these two methods is in sample preparation. Comparative measurements between two methods were performed using a sodium boro-disilicate glass containing 5%mol of alumina. The results showed good agreement in the mid-range of glassy viscosities, 105 to 107 Pa.s. In the liquid state, there were no significant differences between the two methods.

Jan 1, 2003

By Tang Chaoho

Laboratory research on the reducing and matte smelting of Jamesonite concentrate has been carried out. The influence of the process conditions such as the smelting temperature, the amount of pyrite cinder (the agent of fixed sulfur) and the amount of additives on the smelting process have been studied. Under the optimum condition the direct recovery ratios of antimony and lead are 83.26% and 68.50% respectively. The ratio of fixed sulfur is 98.97% but more than 15% lead and 30% silver remained in the ferrous matte. The key problem to be solved of this new process is how economical and effective is the recovery of silver and lead in ferrous matte.

Jan 1, 2003

By Tang Chaoho

Laboratory research on the reducing and matte smelting of Jamesonite concentrate has been carried out. The influence of the process conditions such as the smelting temperature, the amount of pyrite cinder (the agent of fixed sulfur) and the amount of additives on the smelting process have been studied. Under the optimum condition the direct recovery ratios of antimony and lead are 83.26% and 68.50% respectively. The ratio of fixed sulfur is 98.97% but more than 15% lead and 30% silver remained in the ferrous matte. The key problem to be solved of this new process is how economical and effective is the recovery of silver and lead in ferrous matte.

Jan 1, 2003

By Tianzu Yang, Weifeng Liu, Lin Chen, Deyu Wang

"Due to the gradual exhaustion of easily extractive gold ores, it is vital to make efficient use of refractory gold ores which hold 30% gold storage of the world. However, the disadvantage of current processing technologies for refractory gold ores consists of severe pollution, low gold extraction ratio, high investment, etc, thus great research interests were attracted during recent years. This article provides an overview of the distribution and categories of the refractory gold ores in the world. The state of art in processing refractory gold ores by pyrometallurgy, hydrometallurgy and biometallurgy techniques and their industrial applications are highlighted. Potential environmental conservative techniques for efficient gold extraction are also reviewed.IntroductionResources of Refractory Gold OresAs easily extractive gold ores are going to be exhausted with the large scale mining nowadays, refractory gold ores are becoming more and more important. Gold in the refractory gold ore cannot be fully extracted using conventional method (cyanidation) even with fine grinding. The amount of gold in the refractory gold ores is about 1500~2000t in China, which occupies 30~40% of the total gold storage [1]. Therefore, it is vital to make efficient use of refractory gold ores."

Jan 1, 2013

By Gavin Lind

The Minerals Council of Australia (MCA), through its Minerals Tertiary Education Council (MTEC), builds capacity in higher education in the core disciplines of mining engineering, metallurgy and minerals geoscience. Over the past fourteen years, this all-of-industry approach in securing the long-term supply of these critical skills (which remain a chronic skills shortage for the Australian minerals industry) through nationally collaborative programs across sixteen Australian universities delivers spectacular and sustainable results for the industry. These unique, world-first programs are built on a healthy platform of dedicated industry funding and in-kind support and forms part of the MCA’s broader uninterrupted, sustainable education and training pathway to increase workforce participation, workforce diversity and workforce skills, regardless of the business cycle in the industry. This paper will highlight the origins, iterations and current successful programs of MTEC, including its future vision, and presents a mechanism for industry and academia to collaborate to address future professional skills needs in the minerals industry globally.

Jan 1, 2014

By Pedro Morales

At present the Codelco´s smelter & refinery business have growing complexities, concentrates with lower copper grades, higher impurities contents, and environmental restrictions which have lead to refocus the Codelco business, not only by considering the isolated developments for each of the Codelco´s Smelt & Ref complexes, but also as an integrated corporative complex scheme which improve the economy of scale, optimize the synergies, and include new technologies for higher productivity and lower operational costs. Accordingly, for the 2008-2012 period, Codelco have prepared a Development Plan integrated to the smelters and refineries business units that improve its single potentialities of and include the advances for the Teniente Converter [1] and Continuous Converting [2] Technologies, and also include the concept of uncoupling the smelting process from the converting process allowing a higher operational flexibility, and a better control of its contaminants. Thus, processing the white metal generated in the Teniente Converter unit of the smelter A into the smelter B has comparative advantages. These changes in the business concept allow an overall increment of the smelting capacity by processing only white metal as a final product through a very marginal investment in this way the total or partial conversion of the white metal into blister copper is eliminated allowing to use the available gas capture-treating capacity, and available acid plants for increase smelting capacity as well.

Jan 1, 2006

By Ragnhild E. Aune, Mark William Kennedy, Shahid Akhtar, Jon Arne Bakken

"To determine the heating rate of billets using ‘short coils’, an appropriate correction factor must be applied to the theoretical relationship. In 1945, Vaughan and Williamson published a semi-empirically modified Nagaoka coefficient applicable for moderate frequency induction heating processes (10 kHz). Recently it was demonstrated that the method of Vaughan and Williamson gives <10% error in the estimated power when heating aluminum billets at 50 Hz.In the present study, experiments have been conducted on aluminum billets in order to verify an empirical frequency corrected ‘short coil’ equation. Measurements of electrical conductivity (<± 0.5%), current (± 1%), heat (± 1-3%), and magnetic flux density (± 1-2%) have been performed. The results are compared with 1D analytical calculations, and 2D axial symmetric FEM modeling using COMSOL 4.2®. The frequency corrected equation has proven to provide accurate predictions of power (<4% error) within the frequency range 50 Hz to 500 kHz.IntroductionInduction heating is commonly applied to the re-heating of billets before forging or extrusion processes. The resistive heating produced by eddy currents in the solid or semi-solid work piece during this procedure, is driven by the time varying magnetic flux density in the air-gap between the work piece and the coil. The flux in the air-gap is created by the current flowing in the induction coil, i.e. the magneto-motive force. In Figure 1 it can be seen that the currents present in the work piece are concentrated in the outer ‘shell’, or the first electromagnetic penetration depth (dw), and flow in a direction which opposes the magnetic field produced by the induction coil."

Jan 1, 2012

By Chao Li, Hongxu Li, Yang. Xie, Meng Wang, Xiangxin Hao

"With the development and utilization of resources of gold, high quality gold mine resources gradually exhausted, and refractory gold ore has become the main raw material for gold smelting, while the smelting pollutants impacting on the ecological environment is growing, in recent years there have appeared several methods of green extraction of gold such as bio-oxidation. In this paper, the life cycle assessment models about three different gold extraction technologies have been put forward. Material consumption, energy consumption and emissions during each gold production process are analyzed by using GaBi 6 software, and the environmental impact of each process is also evaluated by means of CML2001 methodology. Calculation and analysis results show that the energy consumption and material consumption are the main factors causing the environmental load; and the environmental impacts of the production process mainly attribute to the category of greenhouse effect, resources consumption and environmental acidification. Based on the evaluation, some optimization tips are proposed.IntroductionOver the past decades, as the industry policy environment continues to improve as well as gold exploration and mining smelting capacity continues increasing, gold production shows a prospecting tendency. With the wide use of gold, the demand for gold is growing, while easy smelting gold mine resources become exhausted and refractory gold ore has become the main raw material for gold smelting. In addition, pollutants impact on the ecological environment is also growing year after year.LCA (Life Cycle Assessment) makes evaluation of product “from cradle to grave” as its whole process, up to finding the sources of environmental impacts and solutions, to comprehensively account the use of resources and lower emissions. In the industrial field, life cycle can compare different technologies from different aspects of resource use, energy consumption and environmental emissions [1]. In recent years, using LCA to evaluate metallurgical industry process also has more development. The paper mainly uses LCA and scenario analysis for the gold metallurgical process by GaBi 6, to investigate the environmental impact of three different technologies of gold extraction metallurgical process. The established three evaluation models include the hydrometallurgical, pyro-metallurgical processes and bio-oxidation pretreatment methods respectively. Several environmental indexes would be selected to evaluate the environmental impact in order to find which process has smallest environmental load and some suggestion of reasonable way gold resource utilization."

Jan 1, 2014

By Shijie Wang

In pressure oxidation leaching of copper anode slimes, than 65% of the tellurium is m&apos; cxtraoted during decopperizing. About l0- 15% of the selenium is also dissolved simultane¬ously by severe leach conditions. Current operation for the treatment of the leachate is to constantly recirculate the leach solution through a bed of copper turnings. The tellurium and sele¬nium are precipitated from the leach liquor as copper telluride and copper selenide and sepa¬rated from the solution by filtration. In order to improve the reaction efficiency and reduce the process cost, viz, minimize the copper addition, cut retention time, and reduce the energy consumption; a chemical reducing agent is studied and the cementation process tested in the laboratory. In this paper, the test results are presented and the process chemistry is discussed.

Jan 1, 2003

By John W. Cash

The mineralogy and textures of cyclone dust, sludge, and occasional build-ups in the American Iron and Steel Institute (AISI) direct ironmaking pilot plant at Universal, Pennsylvania have been studied by reflected light, transmitted light, and cathodoluminescence microscopy, and phase compositions have been determined by SEM-EDS. The cyclone dust consists of particles of carbon, metallic iron, sulfur-bearing iron, and wustite. Measurements of particles in the sludge indicates that 69% are less than 2.5 um across, 21 % are 2.5-5 um, and 10% are larger than 5 um. Mineralogically the sludge particles are mainly carbon and metallic iron, with minor wustite and sulfur-bearing iron. Build-ups that sporadically develop in the furnace consist of olivine, hercynite spinel, metallic iron, wustite, pyrrhotite, pseudobrookite, akermanite-ferroakermanite and gehlenite. The microtextures shown by the build-ups indicate that much of that material has precipitated at the build-up loci. This study has been supported by AISI and the U.S. Department of Energy.

Jan 1, 1995

By Denise C. R. Espinosa

The amount of secondary batteries are increasing about 15% by year. Among these batteries, it can be highlighted the NiCd ones, due to their high consumption. In Brazil, the consumption of NiCd batteries grown quickly in the last 5 years, due to the dissemination of cellular telephones and other electronic devices. The first step of a process to recycle spent NiCd batteries is the pretreatment through unit operations of mining treatment. The aim of this work is to define a physical pretreatment to conditioning the waste to a pyrornetallurgical recycling process of spent NiCd batteries used in cellular telephones. Batteries were disassembled by hand to release the different components. The studied batteries are basically composed (by weight) of: 78% nucleus, 18% plastic case and 2% circuits. The grinding of the batteries was performed by knife mill and also by hammer mill. After grinding the material was screened and submitted to a magnetic separator.

Jan 1, 2001

By Olexandr Gydin

The evolution of grain and dislocation structures during cold deformation of the new steel LH800 of Salzgitter AG is investigated in the frame of this work. The main feature of this material is its ability to air-harden by carbon content of about 0.1%. The initial ferrite structure of the metal provides high plasticity at cold deformation and subsequent heat treatment increases tensile strength approximately two times. Described are results of in-situ tensile tests in the SEM. SEM and TEM analysis of grain and dislocation structures evolution in samples, which have been uniaxially deformed to certain strains, are carried out. After statistical evaluation of results the grain elongation against strain is determined. A microstructure of a deep drawn cup is analyzed by means of SEM. A quantitative evaluation of grain elongation on the different cup zones and comparison of these data with prediction results based on tensile tests are carried out.

Jan 1, 2009

By Liang Wang, Sheng-Kai An, Bing Xie, Hong-Yi Li, Cui Li

In order to develop an environment-friendly method for extracting vanadium effectively from aqueous solution containing vanadium, the dynamic adsorption behavior of V by a continuous fixed-bed column which was filled with macro-porous weak base anion exchange resin was studied. Effects of conditions including the bed depth, flow rate, concentration of vanadium ions on dynamic V adsorption were investigated. The optimum adsorption conditions were established at flow rate of 6 ml/min with bed depth of 20 cm. Isotherms studies demonstrated that the column adsorption of V was a favorable chemical ion exchange process in monolayer. Several kinetic models were applied to analyze the adsorption characteristics. Analysis results of the Bohart-Adams model indicated that the adsorption process was dominated by external mass transfer in the initial stage. The Thomas model was appropriate to describe the column behavior, revealing that both external and internal diffusions were involved in the limiting steps.

Jan 1, 2014

By S. Motoiu

Data acquisition is widely used for controlling flash smelting furnaces. A Romanian smelter from which a large amount of data can be collected uses such a technique. A computer program was developed for interpretation of the data. Inputs to the program are the process data files. Abnormal data are identified using standard statistical techniques; they can be edited if necessary. The following methods can be used for the analysis: linear correlation (single or multiple), polynomial correlation or comparison of two average values. Time variation graphs and histograms can be displayed. The random balance method was used for determination of significant parameters influencing the process performance. Not all process parameters are recorded, and some of them are not even measured. The software can compute some of these parameters such as: air flow rate required and the oxygen content of the gas: exiting the reaction tower. The software was used for the interpretation of a large amount of process data. The analysis showed that the process did not operate properly at some times.

Jan 1, 1999

By Steven I. Baskin

Cyanides are utilized in many industrial applications including preparation of chemical intermediates, electroplating, and&apos; mining, Cyanide has been utilized in chemical warfare operations as well Cyanide is also synthesized and found in plants and animals including man where it is thought to perform multiple functions. A variety of enzymes are known to detoxify cyanide under different conditions. These include rhodanese, 3-mercaptopyruvate-sulfur transferase, thiosulfate reductase, cystathionaseand albumin. Cyanide appears tQ exert its toxic effect primarily by inhibiting cytochrome oxidase? although other enzymes are also inhibited. Therapeutic antagonist categories to treat cyanide include methemoglobin formers such as nitrite, sulfane-sulfur donors such as thiosulfate, metal salts or complexes such as cobalt and cyanohydrin-forming compounds such as dihydroxyacetone or alpha keto-glutaric acid. Advantages and disadvantages of each category will be discussed. Newer compounds under development have been found that may allow for prophylactic therapy for cyanide poisoning with minimal side effects; In addition, portable co-oximetry devices may provide real-time measurement of cyanide in field units.

Jan 1, 1998

By J. Huot

It has been shown that magnesium-based metal hydrides such as Mg2Ni could be synthesized by high energy mechanical alloying. This process creates a nanocrystalline alloy that has enhanced hydrogen sorption properties due to the high density of defects and grain boundaries. Unfortunately, this process also requires a long synthesis time (up to 100 hours in some cases). In order lo reduce processing time and cost of synthesis, we have investigated the effect of milling at elevated temperature under an inert atmosphere. Milling at high temperature improves interdiffusion of the elements and reduces the number of structural defects such as vacancies, dislocations and internal strain. It was found that by milling elemental powders at 200°C. a complete synthesis of Mg2Ni could be achieved in 8 hours. This synthesis time is roughly an order of magnitude lower than that of the process conducted at room temperature. The hydrogen sorption kinetics and capacity of this material are comparable to Mg2Ni synthesized at room temperature.

Jan 1, 2002