Search Documents

By M. Patel, G. Djambazov, J. Shrimpton

"Removing zinc by distillation can leave the lead bullion virtually free of zinc and also produces pure zinc crystals. Batch distillation is considered in a hemispherical kettle with water-cooled lid, under high vacuum (50 Pa or less). Sufficient zinc concentration at the evaporating surface is achieved by means of a mechanical stirrer.The numerical model is based on the multi-physics simulation package PHYSICA. The fluid flow module of the code is used to simulate the action of the stirring impeller and to determine the temperature and concentration fields throughout the liquid volume including the evaporating surface. The rate of zinc evaporation and condensation is then modelled using Langmuir's equations. Diffusion of the zinc vapour through the residual air in the vacuum gap is also taken into account.Computed results show that the mixing is sufficient and the rate-limiting step of the process is the surface evaporation driven by the difference of the equilibrium vapour pressure and the actual partial pressure of zinc vapour. However, at higher zinc concentrations, the heat transfer through the growing zinc crystal crust towards the cold steel lid may become the limiting factor because the crystallization front may reach the melting point.The computational model can be very useful in optimising the process within its safe limits.IntroductionLead bullion is commonly refined by removing various impurities (e.g. copper, silver, bismuth, antimony, etc) sequentially. This in normally achieved by the addition of reagents which selectively react with the impurities and the resulting compounds removed by various means. To aid efficient mixing (ensure uniform reactions), batch mixing of materials via the aid of impellers is common practice in a number of industrial sectors. Excess zinc, added during the desilvering process can be removed by one of three methods: (1) Vacuum dezincing - During vacuum dezincing, a vacuum is drawn on the agitated molten lead within a hemispherical vessel (Figure 1). Vaporized zinc condenses on the inner top surface of the vessel. The temperature at which zinc commences to vaporize lowers owing to heating under a vacuum. This enables vaporized zinc to be recovered in the form of high purity crystals without oxidation. The zinc crystals are recovered once the vessel lid is removed and the vacuum is broken. (2) Chlorine dezincing - In chlorine dezincing, molten desilvered lead is reacted with chlorine gas, forming a surface layer of zinc chloride contaminated with small amounts of lead chloride."

Jan 1, 2004

By David Dreisinger

The cyanidation of copper containing gold ores results in the co-dissolution of copper along with gold. Copper dissolution results in elevated cyanide consumption that may make the treatment of the gold ore uneconomic. Copper-cyanide species in gold mill effluents may increase the environmental toxicity of the gold mill solutions. The objective of this study was to examine the use of solvent extraction to recover the copper cyanide species from gold mill effluents. Solvent extraction with Cognis (formerly Henkel) reagents LIX 79 and LIX 7950 was studied. Excellent extraction of copper and cyanide was achieved using pH control in extraction. Copper and cyanide may be stripped from the reagents using basic eluants. Various routes for copper and cyanide recovery from the strip solution were studied. Excellent results were obtained using electrowinning in both divided (Nation membrane) and undivided cells. Cyanide recovery was obtained by AVR treatment of a bleed stream from electrowinning. Full results of solvent extraction, copper and cyanide recovery are reported.

Jan 1, 1998

By Mansoor Barati

The present paper is based on a term project for final year undergraduate students, requiring them to evaluate a process for producing silicon from rice husk. The traditional method for production of silicon involves carbothermal reduction of quartz in electric arc furnaces at temperatures exceeding 2000 °C. The technology consumes a considerable amount of electrical energy as well as fossil fuels, resulting in significant CO2 emissions. A flowsheet for production of silicon metal from rice husk is laid out in this paper. The technology will consist of combustors, which will generate steam using the rice husk biomass, power generator, and electric furnace for reduction of the rice husk. Materials and energy balance calculations presented here indicate that such process can be operated independent of external electricity.

Jan 1, 2014

By R. G. Reddy

Reduction of different chromite ores with carbon was studied as a function of C/FeO ratio and temperature in the range 700 °C to 1100 °C by thermogravimetry (TGA) analysis. Powders of chromite ore(-150 mesh) and carbon(-150 mesh) were thoroughly mixed in a desired proportions and were placed in the reaction crucible. The reduction rates of reactions were determined by continuously monitoring the weight loss as a function of time at constant temperature using TGA set up. The analysis of results suggest that FeO present in the chromite ores is reduced to Fe involving gaseous intermediates CO and CO2. The overall rate of FeO reduction is controlled by the oxidation of carbon. A kinetic equation, that of random nucleation, was proposed. The activation energies for the reduction of FeO, present in Roast Movat and Transvaal ores, with carbon were determined to be 55800 and 23000 J/mole, respectively. The results of the present study are compared with the data available in literature. The low activation energy values as determined in this study suggest that the carbon oxidation reaction is catalyzed. It is concluded from the present investigation that the low grade chromite ores can be significantly upgraded to higher value added chromite that can be used as a feed source for economical smelting.

Jan 1, 1998

By Binxu Zeng, Mark Jolly, Xiaojun Dai

"The traditional investment casting foundries use batch melting and chunky running systems to produce casting components. This method leaves the energy saving issue as subsidiary one. In our research project, one of the partners, the AEROMET international PLC provides the thin wall aluminium component ""filter housing"" for test. The AERO MET uses traditional casting route to produce the filter housing, which only gives 5% --10% yield. In this paper, numerical simulation method is used to analyse filling and solidification of the casting running system. The CRIMSON running system of the filter housing is designed by using casting simulation software, MAGMAS and Flow3D. By working with AEROMET, various configurations of the casting running systems were tested and analysed. Using them ultiple life cycle approach, the energy content of new process is compared with traditional one. It indicates that the CRIMSON process only uses 36% of energy consumed by the traditional route.IntroductionThe investrnent casting is a metal for ming process using expendable patterns, which is a standard casting technique and is widely used to produce quality parts. Its accuracy, versatility and integrity tie itself to important and precious engineering components in Aerospace industry. However, traditional investrnent casting process usually uses chunky runner system and gravity filling method. It not only reduces the casting yield of the product but also causes the pouring defect during the casting. As author's previous research showed that gravity filling method pouring basin and down sprue are two main resources of entraimnent defects generation. No matter how good the running system is, entraimnent defects such as double oxide films (DOF) and bubbles will I get into the casting to cause problem."

Jan 1, 2013

By Augusto Viana Leandro Teixeira

Rare Earth Elements (REE) are fundamental for modern life products and green technologies. Supply constraints and the price peak of 2011 boosted intensive research for alternatives for processing and separation. Complex monazite- type, rare earth ores usually contain high acid consumption impurities, such as iron and aluminum, and radioactive thorium in their composition. These impurities are not removed by conventional concentration processes due to fine, micro-level association between the REE carrying minerals and the gangue minerals. This work presents a selective process route for REE extraction from iron-rich, monazite ores. The process involves sulfation by addition of concentrated sulfuric acid and pyrohydrolysis at temperatures of approximately 700–750 °C. Experimental results show REE extraction higher than 70% and low iron (below 5%) and thorium extraction (below 10%). A method based on thermogravimetric analyses was shown to be adequate to predict the behavior of a given ore sample in the sulfationselective pyrolysis-leaching process.

By Michele L. Bustamante, Gabrielle Gaustad

In recent years, t h e future supply of tellurium has been called into question due to the anticipated rapidly increasing demand from thin film cadmium telluride photovoltaics. Since tellurium is produced as a byproduct of other extractive processes – principally, the electrolytic refining of primary copper sulfide ore – it is important to explore the dynamics of the parent metal extraction and processing – in this case copper – when attempting to answer this question. This research explores the changing landscape of global copper production; introducing system diagramming and the concept of byproduct intensity (BPI) to illustrate concerning downward trends in tellurium supply potential. Upon closer inspection, it is concluding that, while a likely contributor to these downward trends, the increased use of non- traditional copper production techniques alone are not responsible; other factors include market substitution and incomplete data reporting. Additionally, a review of literature on tellurium recovery processing reveals a promising outlook for future supplies; highlighting potential for improvements in yield, which allow producers to make better use of what is available, even in the face of suppressed BPI.

Jan 1, 2014

By J. K. S. Tee

Using a novel method, zinc has been selectively removed from galvanized steel scrap on a laboratory scale. The separation is based on thermodynamic principles: during chlorination in air-chlorine (10:l) mixtures at 800 OC, zinc forms a volatile product (zinc chloride) while iron does not chlorinate as its oxides are more stable than the respective chlorides. As much as 92 % of zinc is removed from the surface of steel within 10 minutes. This process overcomes tedious and costly preparatory stages associated with leaching - electrowinning methods.

Jan 1, 1999

By L. A. André Santos

Atmospheric processing of nickel lateritic ores with low costs has been encouraged. In this work the kinetic of atmospheric acid leaching of a northern- Brazilian ore with 1.63% Ni and large amount of fine particles (d50 ≈ 0.075 mm and 40% below 0.038 mm) is presented. Chemical analysis showed a trend of Ni and Fe concentration in finer fraction (−0.075 mm) and Si and Mg in the coarsest one (−0.500 + 0.150 mm) associated to distinct mineral phases. Nickel is widespread in the mineral matrix. Distinct behaviors were observed as a function of particle size associated to the distribution of silicates and iron oxides in the ore. The kinetic modeling indicated that leaching is controlled by porous layer diffusion at 65 °C, but at 95 °C exhibits a mixed control by porous layer diffusion in initial minutes (60 min) and by chemical reaction or diffusion through the pore layer in final minutes (60–240 min) depends on metal evaluated.

By A. J. van der Zeeuw

The use of SME 529 in the extraction of copper from acidic liquors and of copper and nickel from ammoniacal solutions, is illustrated with results of laboratory and bench scale mixer/settler experiments. Special features of SME 529 are its high loading capacity and the ability to keep the complexes dissolved in the organic phase up to quite high concentrations.

Jan 1, 1976

By S. W. White

Plasma arc technology is increasingly being used to process a number of waste materials. In present research, plasma technology is being investigated to treat waste magnesium baghouse dust, which is a waste material from the Magnetherm process. This dust contains mostly MgO, but also contains NazO, CaO, and KzO. Plasma energy is to be used along with a reducing agent to produce pure gaseous magnesium while keeping the other materials in a slag. The magnesium will then be collected by rapid quenching. A non-transferred arc plasma torch is ideal for this reaction because of its high enthalpy and improved energy efficiency over conventional methods. Another advantage of plasma is that it allows for the pre-heating or pre-reacting of fine particles before contact with the melt. Thermodynamic calculations using the Gibb energy minimization method were used to determine the most stable compositions of the materials at various temperatures. Energy balances have also been calculated. These results conclude that we can recover approximately 98% of the magnesium with a proper quenching technique. The calculated results are compared with the experimental data, and good agreement between them was observed.

Jan 1, 1999

By Versiane A. Leão

The hydrochloric leaching of chrysotile tailings and soapstone powders) is discussed. This two materials are magnesium compounds associated with carbonates and iron oxides. In this work the chemical and physical characterization of formers is presented and the thermodynamic analyses of leaching is carried out. Magnesium extraction is almost complete for chrysotile tailings while, for soapstone powders, one can be reached 60%. The behavior of iron and calcium impurities is discussed.

Jan 1, 1997

By László I. Kiss, Verena Mackowiak, Alexandre Perron, Dominic Toulouse, Alicia Liedtke, Sándor Poncsák

"Bubbles play a very important role in different metallurgical applications like for example in electrowinning. During heterogeneous nucleation, the maximal size of the bubbles growing at the nucleation sites as well as the nucleation frequency is determined by the so-called detachment condition. Detachment occurs when the external forces acting on the bubble exceed the retaining forces along the solid-gas-liquid triple interface line. The phenomenon depends strongly on the shape and orientation of the solid surface and on the nature and strength of the external buoyancy and drag forces. In the present study the detachment conditions of bubbles from downward facing horizontal and inclined plates were studied experimentally under the effect of gravitational and hydrodynamic forces. The results show the deformation of the bubbles under the effect of the external forces and the detachment conditions as function of the bubble volume.IntroductionIn heterogeneous nucleation bubbles are generated at the so-called nucleation sites along the solid-liquid interfaces. They continue to grow there and after they reached a certain size they detach from the solid surface and leave the nucleation site. This scenario is well known both in boiling and electrolysis. During the growth period a stable equilibrium exists between the forces that retain the bubble at the nucleation site and the forces that try to remove it. This equilibrium evolves with the increasing volume of the bubble to the point when the detachment forces overcome the retaining forces.The life of a single bubble generated by heterogeneous nucleation can be divided into two periods separated by the detachment - or in other words by the departure - of the bubble: first the growth at the nucleation site and then the movement away. The knowledge of the detachment conditions makes possible the determination of the maximal volume of the bubble at the nucleation site that, in tum, makes possible the determination of the nucleation frequency. This is why so many researches have been directed toward the clarification of the details of the bubble detachment in the past decades. The equilibrium between the attaching and separating forces depend on the presence of body, surface and flow induced forces in the liquid, on the geometry and orientation of solid surface, on the properties of the solid-liquidgas system etc."

Jan 1, 2004

By Shadia J. Ikhmayies

SnO2:F/CdS:In bilayers were produced by the spray pyrolysis technique on glass substrates. The structures were characterized by recording and investigating their transmittance curves, I-V plots, X-ray difractograms (XRD) and by observing their scanning electron microscope (SEM) images. From the I-V plots it was found that the SnO2:F forms an ohmic or quasi-ohmic contact with CdS:In. XRD patterns show the polycrystalline nature of the films and show that there is a small shift in the position of the (200) line of SnO2:F without the appearance of new peaks. The morphology of the structures are compared with those of SnO2:F alone and CdS:In alone on glass substrates.

Jan 1, 2009

By T. R. A. Davey

A simple model for metal solution behaviour may be derived, on the basis of dilute solution solubilities (where? log concentration of solute varies linearly with reciprocal temperature) and not-so-dilute region solubilities (where the log of the alpha-function at saturation frequently varies linearly with reciprocal temperature) and assuming activity to vary according to the quadratic formalism in between. Matte binary systems usually exhibit regular .solution behaviour when the constituent species are chosen appropriately. In many recent papers, metal solubilities in .slags are expressed as the sum of several different and supposedly independant molecular species (e.g. oxides, sulfides, chlorides), Such a view is untenable because of the now proven ionic nature of slags. Some possible reasons for the great effect of sulfur on copper solubilities in slags are discussed.

Jan 1, 1985

By M. C. Flemings, S. B. Brown

"Metallurgy, as all of material science and engineering, rests on the intellectual foundations of processing-structure-property-performance relationships. Today it is widely recognized that processing has been too long neglected and presents exciting opportunities for exploitation. New processes, many of them already in the laboratory, will be exploited in the year 2000 and beyond, for near net shape forming and for achieving-new metallurgical structures and composite structures. Process modelling will alter the way we think about process and product design. Processes themselves will increasingly be automated and controlled by computers, altering the nature of the workplace and the tasks of the metallurgical engineer of the future. IntroductionInnovations in metal processing is hardly a new phenomenon, with the field thousands of years old. Nonetheless, the next few decades offer particularly important opportunities to improve our ability to process these materials. We appreciate today the variety of processing paths available to us, including vapor-, plasma- and electro-deposition, multiple phase and casting technologies, and non-equilibrium processes, and how these affect structure at the atomic level and at higher levels of aggregation. We understand the basic physical mechanisms involved far better than even before and have remarkable new abilities to predict, control, and simulate the kinetics underlying processes, and the processes themselves.The following sections describe these new opportunities in greater detail. First, we examine developments in the modelling of metal processing. We then consider some implications associated with process control and automation. Finally we present what we consider to be particularly promising metal processing technologies, and conclude with a few summary comments."

Jan 1, 1988

By Travis Knight

Mixed uranium and refractory metal carbide systems have been proposed for space nuclear power and propulsion applications. Solid-core space nuclear reactors could be utilized for low- earth-orbit (LEO) to geosynchronous-earth-orbit (GEO) transfers, manned missions to the moon or mars, and orbiter missions to the outer planets. However, these high performance space nuclear reactors present some challenging materials engineering requirements for operating in a high temperature, high radiation, and hot hydrogen environment. Since the RoverNERVA programs were concluded in 1973, significant advances in ultrahigh temperature materials technology have been made which can be applied to the development of an advanced solid-core nuclear fuel. Nuclear thermal propulsion (NTP) was first studied in the U.S. beginning in the mid-1950's during the RoverNERVA programs. During that time, about 20 rocket reactors were built and tested. More recently, Russian nuclear rocket reactor tests with pseudo-ternary carbide nuclear fuels (U, Zr, Nb)C and (U, Zr, Ta)C have been operated at temperatures as high as 3300 K for one hour. This study examined the processing parameters for fabricating the pseudo-ternary carbide, (U, Zr, Nb)C.

Jan 1, 1999

By C. Gasparrini

Mineralogy may be applied to the selection of appropriate separation techniques, as well as to assist in the evaluation of problems causing loss of metals and other economically important elements during plant processing. Mineralogic studies may thus help develop techniques to optimize metal recoveries. The present paper describes how such factors as the minerals in which the elements of interest are concentrated, their chemistry, the chemistry of the associated minerals, grain size and textural associations with other minerals in the ore, may affect decisions on separation techniques for the recovery of economic elements. A number of case studies are described in which the mineralogical observation of ore samples has revealed the cause of problems experienced in the extraction of select precious and base metals, or has been decisive in the choice of appropriate techniques for recovery.

Jan 1, 1981

By Steve Johnston, Mowafak Al-Jassim, Fei Yan, Omar Sidelkheir, Alain Blosse, Katherine Zaunbrecher

"Imaging techniques are applied to multi-crystalline silicon wafers and solar cells throughout the production process. Photoluminescence imaging, both band-to-band and defect-band, is used to characterize defects and wafer quality at all process steps. These steps include bricks sawn from ingots, wafer sawing, cleaning and texturing, emitter diffusion, edge isolation and glass removal, anti-reflective coating/passivation, and metallization of finished cells. Bricks, wafers, and cells can be imaged at a rate commensurate with in-line measurement, giving spatial information to characterize quality and defect content. Photoluminescence images on silicon bricks can be correlated to lifetime measured by photoconductive decay and could be used for high-resolution characterization of material before wafers are cut. The defect areas in as-cut wafers are compared to imaging results from electroluminescence and lock-in thermography, and cell parameters of near-neighbor finished cells, showing correlations to efficiency, open-circuit voltage, and short-circuit current.IntroductionImaging techniques can rapidly characterize material quality and defect density. Photoluminescence (PL) imaging can be applied to silicon from the brick level to all wafer process steps [1-8]. At the brick level, material thickness allows for measurement and correlation to lifetime where surface recombination effects are minimized [6, 7]. At the as-cut wafer level where thin unpassivated wafers prevent accurate lifetime assessment due to surfaces, defects can still be categorized and quantified to predict finished cell performance [3-5]. Defect regions can be identified by recombination-limited band-to-band PL or by defect-band emission [9-12]."

Jan 1, 2012

By Nural Kuyucak

Acid mine drainage (AMD) occurs at operating and abandoned mine sites as a result of oxidation of sulphide minerals, and is characterized by low pH and heavy metal contamination (e.g. Fe, Zn, Cu, Cd, Al, Mn). It usually requires treatment before release in order to meet regulatory requirements. Chemical methods, such as lime neutralization and sulphide precipitation, are commonly used to treat AMD. However, the conventional processes require high capital and operating costs, and constant attention for many years into the future. In addition, the amount of sludge produced by conventional lime treatment processes poses an increasingly significant disposal problems at decommissioned mining operations. There is, therefore, an urgent need to develop passive, cost-effective processes for mitigating AMD and seepages originating from tailings and waste rock areas. Noranda Technology Centre (NTC) has been evaluating various methods being developed by other institutions, and exploring new ideas, to achieve passive in situ processes for treating AMD. These methods include anoxic limestone (ALS), lime-organic mixture (LOM), biosorbents (BIOS) and biotrench (BT). Current investigations at NTC involve preliminary bench-scale testing. Based on the outcome of the bench tests, a field test will be performed at a selected site. Details of the bench tests are discussed in the paper. Key Words: Acid mine drainage, treatment, metals removal, passive treatment, anoxic lime, limestone, biological treatment, sulphate reducing bacteria, biosorption, biosorbent

Jan 1, 1993