Search Documents

By Luciano B. Oliveira, Angela O. Costa, Sergio N. Monteiro, Luis Guilherme C. Marques

"Biofuels are gaining a relevant role in today’s world not only as a solution for the decreasing petroleum reserves but mainly as a positive contribution to the efforts in global warming mitigation. In Brazil, since 1975, the replacement of gasoline by ethanol started a so-called PROALCHOOOL program, which is now being complemented with the replacement of petroleum diesel by biodiesel. This biodiesel program was officially created in 2005 with mandatory goals, supported by legislation, of 2% addition in 2008 and 5% addition in 2013 into all commercialized regular diesel. In this work, a critical analysis of the Brazilian biodiesel program is presented. The technical aspects related to the different raw materials, including wastes, available for biodiesel conversion as well as the economical conditions associated with production costs and market logistic are discussed. The environmental benefits associated with the retention of greenhouse gases are also discussed.IntroductionToday the commonly accepted fact that the petroleum world reserves are probably passing through a maximum and start declining in terms of the total amount that can be extracted by existing technologies is motivating significant changes in our society. The continuous increase in the price of gasoline and other liquid fuels is an immediate worrisome and visible consequence. However, more than an economical problem, our civilization is already facing the effects of global warming, due to CO2 emission from burning fossil fuels, mainly from coal and petroleum. It is now realized that a large scale solution for these problems demands the prompt substitution of non-renewable fossil fuels by others that, in addition of being renewable, have a relatively lower contribution to the greenhouse gases."

Jan 1, 2008

"EAF dust is categorized as a hazardous solid waste. EPA approves only two treatment methods: either sending the dust to zinc recycling facility, or stabilizing it first and then disposing it to a specially-lined landfill. Both treatment methods are costly to EAF steelmakers. In order to reduce the cost and even better to make profit from the dust, EAF steelmakers need to find a costeffective technology to separate zinc from EAF dust. This paper is dedicated to discussion of a novel recycling strategy: in-process separation of zinc from EAF dust. The concept of in-process separation of zinc from EAF dust is first defined, and then a simple Zn concentration model is developed. From this model, two approaches of in-process separation of zinc from EAF dust are derived: (1) prematurely capturing dust at very high temperature when zinc is still in vapor status, (2) prematurely collecting dust immediately after quickly cooling EAF off-gas from high temperature to low temperature. Next, thermodynamic analysis is conducted to understand zinc behavior in EAF off-gas. It is demonstrated in theory that zinc is in vapor status while it exits from electric arc furnaces. At last, recycling routes and economics of in-process separation of zinc from EAF dust are discussed.IntroductionElectric arc furnace (EAF) plays an increasingly important role in steel production. According to USGS, steel production from electric arc furnaces has long exceeded that from basic oxygen furnaces [JJ. In 2009, electric arc furnaces produced 64% of total steel in the United States.Along with the fast growth of EAF steel production, generation of EAF dust is also rapidly increasing. A survey by AIM Market Research showed that 10 - 20 kg EAF dust was generated for every ton of EAF steel produced [2] In 1999, the United States alone produced 770,000 metric tons of EAF dust [3] In Europe, annual generation rate of EAF dust is more than one million tons [4-5]. In Japan, about 450,000 tons of EAF dust is produced each year [6] Globally, total generation of EAF dust was estimated to be more than 5 million tons per year [5] EAF dust is categorized as a hazardous solid waste since it often contains heavy metals, such as lead, chromium and cadmium. US Environmental Protection Agency (EPA) approves only two methods for treating EAF dust: (1) recycling the dust by EAF-dust recyclers, and (2) specially landfilling the dust for disposal after it is chemically stabilized. These two methods of treating EAF dust are both very costly to EAF steelmakers. It was estimated that a fee of $150 to $200 per ton of EAF dust was paid for various treatment options, which added approximately $2 - 3 cost for every ton of liquid steel produced by electric arc furnaces [?J."

Jan 1, 2011

Accretions of dust on the walls of the offtakes from furnaces and in the waste heat boiler are a cause of significant operating and maintenance problems in non-ferrous smelters. The dust originates from entrained solids in the gas stream and vaporised species that condense during gas cooling. Control of dust formation is very important for minimising the formation of accretions and reducing the severity of environmental problems caused by toxic species, such as those containing arsenic, in the dust. The present paper discusses the formation of accretions and the condensation of dust in copper smelting from a thermodynamic viewpoint. Changes, in gas composition and the amounts and identities of the condensed species in the dust are calculated using computational thermodynamics. Interactions between dust species to form accretions are considered in the light of appropriate phase equilibria. The results show that the nature of the dust formed varies greatly, depending on the temperature and the amount of oxygen present during cooling. Control of the amount of oxygen is required if offtake and waste heat boiler accretion problems are to be minimised.

Jan 1, 2002

By S. Peng, Vaughan R. Voller

"Free boundary problems are a common occurrence in materials processing operations. An important example is the filling of material into molds. This paper looks at filling problems associated with polymer processing, in particular Resin Transfer Molding (RTM) and Compression Molding. A general, single governing equation is developed which on numerical solution provides predictions for the position of the polymer front in the mold during filling. Both fixed and deforming finite element solutions are developed. Application to polymer filling test problems reveal that the fixed and deforming grid scheme are accurate and compare closely with each other.IntroductionProblems arising from the analysis of material processing operations often involve the tracking of a moving boundary, on which a balance conditions needs to be met, or the locating of a free surface that defines the solution domain. Material processing examples of so called ""free and moving boundary problems"" include; the tracking of solidification/melting fronts[l], the tracking of the metal/gas interface during the filling of a mold[2] and location and shape of a skull (freeze line) in a melting furnace[3].Computational solution of free and moving boundary problems usually fit into one of two classes, viz.1. Fixed grid scheme: In which the spatial domain is covered by a fixed grid (mesh) of node points and the solution uses an auxiliary variable (e.g. a local liquid fraction) to track the moving boundary or locate the free surface.2. Deforming grid scheme: In which the grid in the spatial domain is continuously deformed (or adapted in a steady state problem) such that a specified set of grid points lie on the moving boundary or the free surface.Details on the basic underlying features in these two classes of solution can be found in the excellent monograph by Crank [4]."

Jan 1, 1994

By T. Shimizu

In Japan, the emission standard of selenium in effluent was set at a maximum of20 mgll in Feb. '94 for the first time, and it is scheduled to be further decreased to a maximum of 0.1 mg/I from Feb. '97 due to tightening of the Water Pollution Prevention Act. Selenium (IV) and (VI) are generally found in effluent from precious metals refineries. Although selenium (IV) can be easily eliminated by some reducing agents, selenium (VI) is more difficult to be reduced. Therefore, many smelters are having difficulty in complying with the new emission standard. At Mitsubishi Materials' Naoshima smelter, the behavior and the elimination of selenium in effluent have been extensively investigated. As a result, it was found that two strategies were particularly effective. One of them is improving the overall operation of precious metals refinery, that is, feeding uniformly the effluent to the waste-water treatment plant, reducing the effluent volume by recycling and recovering more selenium (IV) in the effluent. The other is eliminating selenium (VI) in the effluent from the precious metals refinery. It was found that selenium (VI) can be effectively reduced by using hydrazine under high? sulphuric acid concentration and high temperature conditions. By using these measures, it is considered that Naoshima Smelter will be able to comply with the new emission standard.

Jan 1, 1996

By A. McLean, S. Dawson, N. D. G. Mountford

"IntroductionIn order to predict the accepted industrial practice for the year 2000, it may be helpful to first consider the rate of development of scientific knowledge. If the speed with which man can travel on commercial vehicles is taken as a criterion for determining the rate of progression, then it can be seen from Figure 1 that advancement in our present century is very rapid. Likewise, if computer technology is used as a criterion for the measurement of scientific advancement, it becomes evident that technological evolution can be highly exponential. These two examples are sufficient to demonstrate that engineers and managers cannot afford to regard scientific development as being linear with respect to time if they are to avoid underestimating the needs of society.Within this framework of overall development, the time required for individual ideas to progress from inception to regular application has decreased considerably. For example, X-rays first discovered by Roentgen in the 1890's and now used widely in medicine and engineering, required a developmental period of some eighty years. The motorcar evolved from early beginnings at the turn of the century to a position of great social impact in sixty years. Rectifier materials used in high frequency radar to the present explosion in communications, required forty years. As illustrated in Figure 2, the period is shortening rapidly.The use of sound waves appears to be following a similar path. There is now a considerable body of knowledge concerning their behaviour and exceptional advances have been made. In medicine and engineering the sonic approach to examination is well established, and acoustic testing forms the basis of several diagnostic and quality control applications. With respect to metals engineering, ultrasonic testing has contributed to the understanding of the relationship between the size and number of internal defects and the probability of premature failure. This has allowed the designer to incorporate appropriate safety factors in his designs; but more importantly, the realization of the deleterious effect of inclusions on the performance of the final product has resulted in a continuous pressure on the material suppliers to reduce the number of defects in their products.It is not only the designer who is demanding defect free material but also the fabricator, as material breakdown during manufacture can be prohibitively expensive. Examples of this can be found in both the aluminum and steel industries where ultra clean sheet is required to ensure that rejections are minimized during beverage can manufacture and other deep drawing operations."

Jan 1, 1988

By Armando Valenzuela

Arsenic has been a common impurity in copper sulfide concentrates treated pyrometallurgically in Chile, which inevitably during the smelting-converting process reports in the final copper product affecting its properties, but also affecting environment as a very toxic occupational hazard. The enforcement of air quality standards, which regulate pollutants such as sulfur dioxide, particulate matter, and arsenic, has resulted in the implementation of pollution abatement plans and emission reduction schedules mainly by state-owned copper concentrate smelters. Investments associated with these plans incorporated gas-handling systems in order to capture polluting emissions. Electrostatic precipitators recover dusts containing mainly Cu and As which are leached to recover copper, while arsenic is disposed currently in the form of ferric arsenate. Gases containing high sulfur dioxide content are treated in plants to produce sulfuric acid, which is used in various classical and new hydrometallurgical processes. Additionally, smelters have effluents treatment plants for arsenic disposal either as ferric arsenate or calcium arsenate/arsenite. This paper reviews the environmental situation of the Chilean metallurgical industry, and the present trends for arsenic management are particularly emphasized since Chile is the world?s largest copper producer.

Jan 1, 2006

By Nagy El-Kaddah, T. T. Natarajan

This paper describes a novel approach for modeling three-dimensional electromagnetically driven flow in inductively stirred systems, and its application to modeling electromagnetic and flow phenomena in sub-mold rotary stirring of billets. It is based on a new T-\jf potential formulation of electromagnetic field, which does not require the calculation of the field in free space. A finite element algorithm has been developed for solving the electromagnetic field and Navier-Stokes equations in the fluid flow domain. The computed results have shown that the electromagnetic force field generates a strong rotational flow within the vertical section covered by the stirrer, and a relatively strong secondary flow beyond the stirrer. It has also been shown that the rotational and secondary flows were driven primarily by the vorticity of the force field at the billet corners. The induced flow in the molten pool was found to be turbulent and the effective mixing region in the molten pool was about three times the length of the stirrer. The mathematical approach presented in this paper provides the theoretical framework for quantifying these effects for any given stirrer configuration and operating parameters.

Jan 1, 1999

By Pinakin C. Chaubal

Today?s steel industry is in a vibrant and resurgent mode. This transformation has been in the making for some time now. Over the last few decades, the industry was steadily transforming itself into becoming a high tech industry. New technology was adopted, efficiencies were enhanced, lean manufacturing concepts were brought in and a strong customer focus was developed. Today?s mills employ sophisticated instrumentation, computerized monitoring, on-line smart systems etc. driving processes that are producing at rates of many tons/minute. All this is not possible without judiciously using the latest available technologies in various fields and developing a more sophisticated work force. Prof. Sohn has been a pioneer in driving the concept of process engineering in process metallurgy. In this paper the focus is on some aspects of process engineering ? primarily process modeling - as applied to iron and steelmaking processes. Examples are shown to demonstrate how problems have been addressed. Some thoughts on future directions are presented.

Jan 1, 2006

By N. J. Themelis

In the last two decades, the Outokumpu flash smelting process has become the dominant new technology for copper smelting and has? also been applied to the smelting of other metal sulfides. The application of oxygen enrichment and improvements in concentrate burner and furnace design have resulted in ever increasing smelting rates per unit volume of the reaction shaft. This paper examines the. rate phenomena taking place in the reaction shaft of the Outokumpu furnace and compares information obtained from a mathematical model of heat and mass transfer rates to results obtained in pi1ot tests conducted at Pori, Finland, and to actual performance of a number of flash smelters around the world. 2?

Jan 1, 1985

By June-Yong Eom, Jong-Jin Pak, Jung-Mock Jang, Min-Kyu Paek

The nitrogen solubility in liquid Mn-Si, Mn-Si-Fe, Mn-Si-C and Mn-Si-Fe-C alloys has been measured by the gas-liquid metal equilibration technique in the temperature range of 1673-1773 K. The additions of silicon, iron and carbon significantly decreased the nitrogen solubility in liquid manganese alloys. The experimental results were thermodynamically analyzed by the Wagner’s formalism to determine the first- and second-order interaction parameters of silicon, iron and carbon on nitrogen in liquid manganese. The thermodynamic parameters can be used to predict the nitrogen solubility in ferromanganese and silicomanganese alloy melts as functions of the melt composition and temperature at given nitrogen partial pressures.

Jan 1, 2014

By J. M. Rapkoch

In late October 1996, an acid plant at a major U.S. copper smelter was faced with unexpected and rapidly increasing pressure drop across the gas cooling tower in the acid plant, indicating a build-up on the packing. This threatened to halt operations if not resolved. Earlier that month, a smaller vessel in the acid plant was found to be completely plugged with lead sulfate. It was feared that a similar fate awaited the gas cooling tower unless the scale build-up was stopped. Although lead sulfate is present in most copper smelter acid plants, this accumulation was unusually severe. An investigation was launched to find the source of the lead, determine how lead is transported to the gas cooling tower, recommend operating practices to prevent such severe scaling, and seek ways to recycle the lead value in the scale covered polypropylene packing. Late in the investigation it was learned that the lead originated from an improperly executed recycling program.

Jan 1, 2000

By M. Okido, O. Takai, Z. Zhao, M. Ishikawa, R. Ichino, K. Kuroda

"Electrolytic method was applied to calcium phosphate coating on titanium plates as an excellent technique for high density and intensive contact of coated films on biomaterials. The effect of H2O 2 as oxidation reagent on coating characteristics was examined to obtain biomineral films. Solution was containing 7.0 X 10·3 mol/dm3 ofCaC12 and 3.0 X 10·2 of Ca(H2PO4)z, kept at 55 ""C. All deposits were hydroxyapatite (HAp) in this study, independent of H2O 2 concentration, applied cathodic potential and solution pH. In the case of H2O 2 addition, an increase in cathode current started at the low potential, namely, ca. -0.2 V (vs. SCE). In contrast, the current increased at more than ca. -1.4 V in the solution without H2O 2 addition. H2O 2 appeared to be an effective reagent for increasing nucleation density and improving adhesion of deposits on titanium plates.IntroductionIn recent years, many researches have been undertaken to develop the techniques of calcium phosphate coating on titanium or bioglass for medical implantation. High density and intensive adhesion of coating are necessary for adding bioaffinity to these materials and for inducing bone morphogenesis on them when implanted in human body.1) Electrolytic deposition has been a newly developed method as high-speed deposition process. By this method, the supersaturation of calcium phosphate can be increased just in the vicinity of metal substrates and the heterogeneous nucleation is promoted on them. In this process, H2O is reduced according to eq. (1) on the cathodically polarized electrode"

Jan 1, 2000

By Akira Yazawa

The continuous converting has attractive advantages, but further experimental studies on the slag are required, when the process is considered thermodynamically. The summarized experimental results, obtained with iron silicate slag and with ferrite slag and results relating to actual operation are described and discussed in this paper. At first, equilibrium relations at controlled oxygen potentials among three melts of silica-saturated iron silicate slag, white metal and copper are investigated. The results obtained for slag agreed with the thermo-dynamical predictions. Namely, to suppress a magnetite separation, the system should be at high temperature; in the case of the S02 gas of 10 kPa, for example, magnetite did not separate from the slag at 1300°C, but at 1250 and 1200°C the slag was saturated with magnetite even at lower SO2 pressure. Copper losses caused by dissolution of its oxide increased with increasing 5O2 pressure, and were slightly lower than those reported in previous papers without the matte phase. When the continuous converting slag does not contain any appreciable amount of silica - in contrast to the conventional smelting slag ferrite slag would form, but there was no published fundamental work on-ferrite slags. Hence, the melting behavior and activities of the system CaO-Cu2O-Fe2O3 have been investigated. The liquidus diagram in nitrogen atmosphere was, constructed using both thermal analysis and quenching method. The low liquidus temperature region without magnetite separation was found in the part of low content of Cu2O in the section Cu2O-CaO-Fe2O3 and Cu2O?Fe2O3¬CaO?Fe2O3. The activity of Cu2O in the system was also measured. Slags, composed-of CaO, Cu2O and Fe2O3, in platinum crucibles were equilibrated at 1250°C and controlled oxygen pressures. After quenching, the-composition of slag and platinum crucible were determined qualitatively. On the thermo-dynamic analysis of the results, iso-activity lines were drawn, and it was shown that the slag in the converting furnace of the Mitsubishi process exists in an adequate region of the composition triangle.

Jan 1, 1976

By E. Kuzeci, R. Kammel

"Lately various voltametric methods have gained increased attention as an analytic tool in hydrometallurgy. Voltammograms with mercury drop electrodes or glassy carbon electrodes provide information about the electrocrystallization of cathodic deposits and allow calculation of kinetic data by means of characteristic parameters like the peak potential and peak current and their variation with the voltage scanning rate.Cyclic voltammograms are also suitable for identification of reaction sequences. Voltammograms with carbon paste electroactive electrodes containing metal sulphide additions reveal information about the dissolution behavior. The stripping voltammetry can be applied to analyze metal ions and organic additives (e. g., thiourea) in extreme low concentration. Typical application of the various methods studied with microcomputer controlled measurement system are explained by examples selected from copper hydrometallurgy.IntroductionThe use of electroanalytical methods in metallurgical process control can be dated back to the starting period of industrial copper refining, when the deposition of the metal ions was followed electro-gravimetrically by weighing the electrode with deposits (1). The principles of metal deposition and dissolution have not changed but the methods to follow these phenomena were subjected to noticeable developments and especially the introduction of polarographic investigations by Heyrowsky (2) has greatly contributed to the progress in electro-analysis. A review about the fundamental work on the electrochemical kinetics in earlier time is compiled in a monograph of Vetter (2). With the steady improvements in the instrumental techniques, it is nowadays possible to apply several current and potential modulations for measurements with improved selectivity and sensibility. There is however, still a lack in theoretical interpretation of the data obtained. More theoretical information are already available for linear voltametric methods for systems where reduced as well as oxidized species are dissolved in the electrolyte (4, 5). Some recent investigations have also shown the reliability of these techniques to study electro-crystallization (6, 7). Main fields of the application in the hydro - and electro-metallurgy are:"

Jan 1, 1989

By R J. Singh, E. Z. Chacko, Devilal, S. K. Jha, Rina Sahu, Sheshank Shekhar

"Breakouts are one of the biggest problems encountered during continuous casting of steel billets. Billets get cracked locally or break completely in two parts during solidification causing the liquid part of the partially solidified billet to empty inside the cooling chamber. Proper control of important parameters is necessary to avoid break outs during continuous casting. In the present work, the nature of the break outs at a billet caster at Tata Steel was studied. Data analysis was also done for certain casting parameters and the Sulphur tracer test was conducted to understand solidification in the mould. It was found that to reduce the occurrence of break outs, it was necessary to tune the operations based on the grade being cast and the design of the mould tube being used.IntroductionA break out during the continuous casting process is a rupture of the partially solidified shell inside the secondary cooling chamber, causing the contained liquid steel to spill out. In the mid 1970s while continuous casting technology was still in early stage of development, causes of breakouts was not well understood. Today, with technological development much has been understood about breakouts but, most of the understanding has been in the slab casting process wherein due to the higher level of instrumentation, a lot of information has been gained. In billet casting however, due to the geometry of the mould housing with the tube mould, multiplied by the complexity of the multiple strands, instrumentation has not been used and obtaining data for analysis has been difficult.Breakouts at billet casters are still the main hindrances to production. A break out results in a loss in production since the strand which has had a break out is now not available to produce and thus a six strand caster would be reduced to a five strand caster, increasing the time for casting the same tonnage. Additionally extra set up time is required as more often than not a mould change is required in order to have the strand casting again."

Jan 1, 2014

By Pekka Taskinen, Hannu Johto

"Copper sulfide concentrates often contain impurities such as lead and iron. The phase stabilities of the sulfide impurity systems in metallurgical process conditions are in many cases unsatisfactorily known. Thermodynamic information of a system gives better understanding of its behavior of metal making processes, but also has effects on the economic and environmental factors of the production process. In this study, isothermal equilibrium and quenching experiments of the stable phases of the system Cu2S-FeS-PbS at 700 and 900 °C were carried out and based on the experimental results, Gibbs triangle of equilibrium phases of the system was outlined.IntroductionThe knowledge of stabilities of phases and the thermodynamic properties of many sulfide systems in the temperature range of 500-1200 °C are quite limited. Especially, the knowledge of liquidus surfaces of multicomponent sulfide systems is essential for making many metallurgical processes more environmental friendly and allowing the utilization of complex concentrates. In this work, the aim was to investigate the phase stabilities of the quasiternary system CU2SFeS- PbS using evacuated silica ampoules. Of greatest interest were the properties of the liquidus surface in the system, in order to be able to predict better the formation of a liquid phase in metallurgical processes."

Jan 1, 2012

By Pengkai Wang, Huimin Lu, Xiaoxiang Zhang

"In this paper, it was studied an electrochemical reduction process of carbon dioxide in ionic liquids such as 1-n-butyl-3-methylimidazolium hexafluorophosphate ([Bmim] PF6) as the electrolyte. The electrolysis experiments were carried out under current and potential controls. The cathode products contained carbon nanotubes, carbon nanofibers, nanographites, and amorphous carbon. To establish the actual current and potential ranges, the electroreduction of carbon dioxide dissolved in the ionic liquid was studied by cyclic voltammetry on glass-carbon (GC) electrode at room temperature. The electrochemical mechanism of carbon dioxide electroreduction was studied for explanation of all obtained results. Carbon dioxide in ionic liquids was electroreduced, similar to metals oxides being electroreduced in molten salts.IntroductionGlobal warming caused by the increase of carbon dioxide in the atmosphere has become one of the most concerning environment problems, so the solution to this greenhouse effect is very urgent. However, the carbon dioxide is also a cheap and abundant raw material that represents a potential source for the production of chemicals and fuels. Therefore, the development of the technologies that achieve simultaneous reduction and conversion of carbon dioxide to fuels is important. The electrochemical reduction of carbon dioxide is one of the effective approaches to transform CO2. Many investigations have been carried out on the electrochemical reduction of CO2 in both aqueous [1] and non-aqueous [2] electrolyte solutions with different electrodes. The solubility of CO2 in water is very low even under high pressure of CO2, and some investigators have brought focus into the electrochemical reduction of carbon dioxide in organic solvents, because they dissolved much more CO2 than water did. However, the hazardous or toxic properties of organic solvents hinder their use."

Jan 1, 2009

By Seyed Mohammad Taghavi

In this report, the efficacy of different factors such as temperature of reaction, time of reaction and depth of bed are investigated in a process of recovery of zinc oxide from zinc ore concentration residues in a fluidized bed furnace. Under optimum conditions, there was more than 93.5% zinc oxide in products.

Jan 1, 2006

By M. Sakamoto, S. Karaswa, Y. Yoneoka, Y. Ohmizo

"The Annaka Refinery has been processing leach residue by Waelz process for 17 years. Recently, the quantity of the leach residue has increased due to a decline in the quality ~f zinc concentrate. Meanwhile, negative factors (e.g. deterioration of water balance due to improved electrolytic power consumption rate) have increased· in the processing of the leach residue.We have implemented various measures in responses to this situation, while striving to increase ·processing capacity and achieve stable operation. AS we have largely completed our assessment of the efficacy of these measures, we report on our recent process improvements.IntroductionWe have been treating leach residue by the Waelz kiln process since 1981. At that time, treatment of only 50,000 tons of leach residue per year was anticipated. However, subsequent process improvements have revised this figure up to 75,000 to 80,000 tons per year.However, today's increased Fe zinc concentrate grade has resulted in increased amounts of leach residue. In addition, improvements have reduced electrolytic power consumption rate of zinc electrolysis, limiting the amount of water that can be used in ·the zinc refining processes and for deaning leach residue. Consequently, we encounter an increasing number of problems and factors adversely affecting leach residue treatment, including increases in water-soluble Zn (WsZn) and. S (S04) in leach residue.To solve these problems, we have taken several measures to ensure long-term continuous operation and treatment of this increased · amount of leach residue. This paper discusses these measures."

Jan 1, 2000