Search Documents

By Gabriel Riveros

Fire refining of copper consists of two stages copper oxidation and copper reduction. Very frequently the capacity of the anode furnace is determined by the rate of copper reduction. The analysis of factors affecting the rate of the oxygen reduction from a liquid copper with solid carbon or injected hydrocarbons pointed out the role of the mass transfer in a liquid copper in final stage of the reduction. Experimental results of copper reduction with graphite and injected natural gas in laboratory- scale crucibles showed two stages of the reduction process with a sharp change of the controlling mechanism. The estimated dynamic surface area of gas bubbles based on the measured bubble frequency and the gas flowrate allowed for the detennination of the reaction constant as a degree of the partial pre-combustion of the air/natural gas mix. The variation of the used reductant as a function of the oxygen concentration and temperature has been evaluated based on the detennined kinetic model. The intensification of copper reduction in fire refining has been discusses on the basis of obtained kinetic data and analysis of various factors detennining the time of reduction.

Jan 1, 2003

By Yong Hack Lee

Nonferrous smelting processes have been through a rapid transformation since the beginning of 1980. The copper smelting technology has changed from the conventional Blast Furnace process to the Flash Smelting and MIB process. In the field of lead smelting, the technology has changed from the Blast Furnace Smelting to the Direct Smelting such as QSL and KIVCET. In 1992, Onsan Refinery successfully commissioned Direct Smelting QSL technology for lead. The QSL could produce more than 160,000 ton per year of lead bullion from lead concentrate and various residues. Moreover, since the year 2000, the TSL (Top Submerged Lance) Technology utilizing the same Direct Smelting process has been successfully commissioned to treat lead concentrate as well as lead sulfate residue produced from a hydrometallurgical zinc plant. This paper presents and compares the energy flows of lead smelting processes such as a conventional process and the Direct Smelting Processes plotted on the Pb-O-S phase diagram. The oxygen potential diagram suggests how to control the oxygen potential in the furnace. Also, it describes the recent operational experience in the TSL plant of Onsan Refinery with necessary mass balance of key elements.

Jan 1, 2003

By Jiang Diao, Yong Qiao, Xuan Liu, Tao Zhang, Bing Xie

The equilibrium experiments between the FeO-SiO2-MnO-TiO2-V2O3-Cr2O3-MgO slag system and solid pure iron were performed to investigate the vanadium and chromium distribution ratio under Ar atmosphere. The influence of w(FeO), w(V2O3) and w(Cr2O3) in slag on vanadium and chromium distribution ratios were studied at 1653 K. The experimental results were compared with calculated distribution ratios based on molecule and ions coexistence theory. Both of them showed that higher FeO content in slag would improve the distribution ratios of V and Cr between slag and hot metal. The distribution ratio of Cr or V increased with the increase of Cr2O3 or V2O3 content, respectively. To optimize the oxidation of V and Cr from hot metal, a high oxidizing slag and suitable content of Cr2O3 and V2O3 in the slag were recommended. The results provided reference for the further study on the extraction of V and Cr in VTi magnetite.

Jan 1, 2016

By Hu Long

Pyrite, as the host mineral in refractory gold ores and concentrates, has been treated by pressure oxidation in sulfuric acid solutions at temperatures above 180°C to liberate gold prior to cyanidation since the 1980's. However, no data is available on the kinetics of pyrite during acid pressure oxidation over the temperature range of 180 to 230°C which is the range employed by most commercial plants. The dissolution of pyrite (FeS,) in sulfuric acid solution under oxygen pressure was investigated at temperatures ranging from 170 to 230°C. The effects of temperature, particle size, agitation speed, oxygen partial pressure, and pulp density were evaluated. The effects of foreign ion addition and the concentration of sulfuric acid were also examined. The apparent activation energy was estimated to be 42.6 kJ/mol in the temperature range 170 to 230°C. The reaction orders with respect to particle size and oxygen partial pressure were found to be -1.5 and 0.5 at 210°C, respectively. Experimental evidence suggests that the kinetics are limited by the surface chemical reaction initially, and then also to some extent by the diffusion of ferrous ions away from the particle surface.

Jan 1, 1999

By Dale Zacherl, Andreas Buhr, Rainer Kockegey-Lorenz

"The microporous calcium hexaluminate insulating material SLA-92 has been introduced as an alternative to refractory ceramic fiber and other insulating refractory materials. Key properties associated with this product include: high chemical purity, long term high temperature stability up to 1500 °C, low thermal conductivity up to 1500 °C, and high thermal shock resistance. The properties of the new material and various applications in the steel and ceramic industries have been reported in previous papers. The current paper summarizes the industrial application experiences with innovative refractories based on SLA- 92 and discusses potential new applications in various manufacturing as well as energyrelated industries.IntroductionSLA-92 was introduced to the refractories industry in 1998 by van Garsel, et al. [1] as a new insulating raw material for high temperature applications, followed by investigations [2] of long term temperature stability for this new lightweight aggregate up to 1500°C.SLA-92 was developed as an innovative alternative to commonly used refractory ceramic fibers. It has unique properties regarding chemical purity and mineral composition and is a microporous, silica-free calcium hexaluminate (CA6 – mineral name: hibonite)."

Jan 1, 2010

By Joel Anderson

Allvac 718Plus is a newly developed superalloy with a good potential for use in fabricated aircraft engine structures when service temperatures exceed 650°C; the limit for standard alloy 718. Fabrication involves welding, where cracking usually is a prohibitive factor. Comparison of the solidification cracking behavior between these two alloys was made by Transvarestraint testing. It was shown that the total amount of cracking was significantly lower for 718Plus alloy, which was associated with a lower amount of ?/Laves or ?/NbC eutectic-type constituents. This in turn is believed to be due to the lower iron content of the Allvac 718Plus material. The analysis of alloying element segregation both within primary dendrite and interdendritic constituents clearly indicates that the segregation of Nb is the controlling factor in determining the final solidification microstructure in these alloys. The Nb concentrations of these constituents are significantly higher compared to the bulk alloy concentration. This was confirmed by the SEM-EDS analysis and calculations assessed with JMatPro, the latter also indicated that alloy 718 is more prone to form Laves and NbC eutectic-type constituents compared to Allvac 718Plus material.

Jan 1, 2008

By J. Vander Linden, R. De Ketelaere, M. Verhaege

In this paper, results are presented concerning the search to implement Supported Liquid Membrane (SLM) technology for the recovery of copper from electroplating effluents. Acid copper electroplating rinse solutions or effluents resulting from the post-treatment of, for example, cyanide-containing copper electroplating baths all contain copper (2+) in the lower concentration levels. A thorough study of the influence of the individual parameters and of their combined impact on mass transfer in small scale laboratory SLM modules has been performed, enabling to set forward the appropriate operating conditions for a pilot plant installation. The pilot plant, containing two SLM modules. of 18 m2 of surface area, has been tested extensively, including short and long term runs, with real process solutions. It was demonstrated that this installation is able to treat 40 l/h of acid copper sulphate rinse solutions· containing 500 ppm of copper. The final copper concentration in the effluent can be reduced to a few ppm while copper metal is recovered by electrolysis of the concentrate. This technology is also applicable to the treatment of solutions with low copper content of origins other than plating shops, such as tailings from copper plants or mine waters.

Jan 1, 2000

By J. P. Evans

The modem copper smelter today utilizes tonnage oxygen for smelting concentrates, generating a high strength S02 off-gas leaving the smelter vessel. This gas stream, which also contains any unreacted oxygen, plus C02, N2 and H20, also carries with it the volatilized portion of heavy metals in the feed, plus partly oxidized sulfide concentrates. The time/temperature history and subsequent treatment of this off-gas stream emerging from the smelting furnace exit up to the acid plant can influence the partitioning and segregation of heavy metals in the off-gas circuit. Depending on this history, the type and characteristics of the chemical and physical reactions which. occur in the gas handling system can be influenced. This fact can also be used as a tool to adjust the separation of copper from heavy metals. In this paper, the impact of different time/temperature histories of the gas, due to different furnace geometries .and design, on the subsequent formation and characteristics of the smelter dust is examined. Based on the available data, several case histories drawn from examples using both bath and flash smelting technologies are analyzed from this perspective.

Jan 1, 1992

By J. P. Evans

The modem 'copper smelter today utilizes tonnage oxygen for smelting concentrates. ,generating a high strength S02 off-gas leaving the smelter vessel. This gas stream. which also contains any unreacted oxygen, plus CO2; N2 and H20. also carries with it the volatilized portion of heavy metals in the feed, plus partly oxidized sulfide concentrates, The time/temperature history and subsequent treatment of this off-gas stream emerging from the smelting furnace exit up to the acid plant can influence the partitioning and segregation of heavy metals, in the off-gas circuit. Depending on this history. the type and characteristics of the chemical and physical reactions which occur in the gas handling system 'can be influenced. This fact can also be used as a tool to adjust the separation of copper from heavy metals. In this paper, the impact of different time/temperature histories of the gas, due to different furnace geometries and design. on the subsequent formation and characteristics of the smelter dust is examined. Based on the available data. several case histories drawn from examples using both bath and flash smelting technologies are analyzed from this perspective.

Jan 1, 1992

By D. G. Mason

During the design of copper refinery tankhouses, there is a need to develop mass balance calculations for many process components, so that optimum physical plant configuration is achieved. Each mass balance is complex, possibly with over 120 interactive variables as basic input data. Recent developments in tankhouse design (e.g. permanent cathodes) have greatly increased the design options available for any project, multiplying even further the requirement for calculations. In the past these calculations were tedious and susceptible to human error. A comprehensive computer program can now simplify the task of the process metallurgist, enabling more sophisticated and sensitive plant designs to be produced. The paper describes the successful development of a flexible mass balance program that originallly was used in a feasibility study which had to be completed within a short time schedule. The program has been further developed and used for design and energy calculations; it can be usefully applied to existing plants to assess the impact of variations in operating parameters. The software takes account of staged liberation, electrolyte purification bleed and generates a reliable process inventory listing: it can also cope with stripper starting sheet options and disparate commercial circuits.

Jan 1, 1987

By Bing Li, Miao Shen, Qiang Wang, Yuqi Chen

Electrochemical methods including cyclic voltammograms, square wave voltammograms, chronopotentiometry are applied to characterize the reduction potentials of Na+ and Li+ ions in LiCl-KCl melts. According to theoretical calculation, the reduction potential for Na+ is slightly more negative than Li+ in NaCl-LiCl-KCl melts at 450℃. However, by electrochemical measurements, the reduction potential of Na+ is slightly more positive than Li+ in the above melt and the potential difference between Na+ and Li+ reaches 0.16-0.2V on an inert W electrode in 1.0-2.0 wt% NaCl-LiCl-KCl melts. An active Pb electrode is used to improve the removal rate of Na+ from LiCl-KCl melts. The reduction potentials for both Na+ ions and Li+ ions on a Pb electrode shift to more positive values and the reduction currents become larger. After 6h electrolysis on a Pb electrode at -3.0V, the practical removal efficiency of Na+ ions reaches 90.12% and the reduced products contain metallic Na and Li with a Na/Li mass ratio of 4.25/1.

Jan 1, 2015

By F. Kongoli

Nonferrous and ferrous smelting industries have recently faced the unavoidable necessity of changing and/or improving the smelting technologies as a result of the use of new raw materials which are becoming available from different geographical areas. These new feed materials usually contain different ore composition and higher level of minor components, which adversely affect the smelting process. Due to the problems encountered in several processes as a result of this feed diversification some work has been undertaken in order to make uniform the feed and avoid later surprises in the smelting process. However this has proven to be very difficult and sometimes almost impossible. In this work a more viable approach is undertaken to deal with this problem. It consists of controlling not the cause of the problem i.e. the feed composition but instead the results of this feed change, i.e. the end-point of smelting technologies. It is shown that this approach, when carried out through advances physicochemical modeling and simulation tools is not only easier and less costly but it also helps the control optimization and automation of the smelting processes. Several examples are given and future work is underlined.

Jan 1, 2003

By M. Kawakami

In the blast furnace, the reduction of iron oxide and gasification of coke occur simultaneously. It is well accepted that the gasification reaction controls the simultaneous reaction. Therefore, it is important to develop highly reactive carbonaceous materials. It is also known that the reaction is accelerated catalytically with the addition of some materials. In the present work, the catalytic effect of iron, nickel and CaO on the gasification of graphite and coke was examined. The catalytic effect of iron, nickel and CaO on the reaction rate of graphite was noticed The effect was larger at lower temperature. At 1373 K, the effect almost vanished. The effect was larger in the order of CaO, iron and nickel. The reaction rate of de-ashed coke increased by the addition of iron and nickel. The effect of iron was larger than that of nickel. The effect was larger at higher temperature, which was contrary to the case of graphite. The reactive surface area increased also by the addition. Therefore, the catalytic effect on reaction rate might be attributable to the increase in the reactive surface area.

Jan 1, 2006

By Ken Baxter

The Sepon Copper Project is located in Laos and has a mineable reserve of approximately 16Mt of ore grading 5% copper with minor gold and silver values. The deposit is a clay-hosted secondary copper mineral suite, predominantly chalcocitic in nature with associated pyrite. The current project design is based on the production of 60,000t/a of LME Grade A cathode by an acid leaching process followed by solvent extraction and electrowinning. Significant metallurgical testwork was conducted as part of the Definitive Feasibility Study (DFS) with process challenges identified and overcome at each phase of testing. Flowsheet configuration is geared to autogenously generating sufficient acid and ferric iron to meet gangue acid consumption and to leach the copper. The ability to maintain acid and ferric levels in the process liquors is strongly influenced by the proportion of pyrite in the ore presented to the autoclave. This paper will outline flowsheet development from preliminary variability testing to pilot plant and DFS design. The Sepon process solution seeks a balance between operability and capital/operating costs, and provides insights into the basic mechanisms influencing flowsheet selection for these ore types.

Jan 1, 2003

By A. V. Tarasov

The insufficient scientific and technical level of a number of operations in the nonferrous metals industry encourages development of new processes and equipment, including smelting in liquid bath, flame-type sparged smelting unit for combined processes, electrothermal process with the use of alternating current (PDF furnace), electrothermal processing of complex raw materials and intermediate products at nonferrous metallurgical plants, etc. One of the most important aspects for development of new processes and equipment in the Gintsvetmet Institute is their environmental safety. Special attention is paid to environmental protection measures, which is also of important economic and social significance. This refers also to a complete extent to processing of reserves of man-made raw materials and wastes available at the existing operations with the use of innovative techniques ensuring not only resource conservation and environmental protection, but also abatement of negative impact on the nature due to accumulated industrial and domestic waste, reclamation of the land used for waste disposal and recycling of nonferrous metals. Technologies and equipment developed in the Gintsvetmet Institute and based on electrothermal processes determine the prospects for ensuring more integrated usage of ores and man-made raw materials.

Jan 1, 2006

By Alex Moyano

The Codelco-Chile is considering different processing options for the projected concentrate from the Alejandro Hales mine (former Mansa Mina mine with high arsenic and antimony content of 6% and 0.6%, respectively), that will produce complex blister copper with high impurities contents, higher than the present values produced at the converting process of the Codelco Norte smelter processing only Chuquicamata concentrates. In order to know both the anodic copper quality and the metallurgical implications when a complex blister copper is processed in the refining process of the CN smelter, the Codelco and IM2 ?task force? evaluated positively the refining process for the complex blister copper by addition of alkaline fluxes at laboratory and industrial scale tests. The promising results of the tests done at laboratory scale at the Tohoku University facilities, allowed a large scale test planning to validate the lab-scale results in 3 refining furnaces of 250 t capacity at the CN smelter. The obtained results demonstrate the industrial technical feasibility to process a complex blister copper in the refining furnaces producing an anodic copper quality suitable for the electrolytic process.

Jan 1, 2006

By M. Kane, O&apos

Operators and designers require a comprehensive model to predict performance of heap leach piles and provide input of reliable and defensible data for economic modelling. A conceptual, theoretical, or numerical predictive model addressing the required metallurgical, geological, biological, and operational considerations should be developed within the framework of the hydraulic performance of the heap leach pile. It is generally agreed that segregation, compaction, and consolidation are physical aspects which significantly affect recovery and in general hydraulic performance. Hydraulic performance of heap leach piles can be described through the application of unsaturated zone hydrology. Unsaturated zone hydrology describes the flow and storage of moisture and oxygen in a porous medium under conditions where the pore water pressure is less than atmospheric. The porous material is "unsaturated" if an air phase, in addition to the water phase and solid material phase, is present. These conditions describe the operation of a copper heap leach pile. This paper will focus on developing an understanding of hydraulic performance in segregated heap leach material and demonstrating that unsaturated zone hydrology can be used as the framework to improve understanding and prediction of heap leach performance.

Jan 1, 1999

By Alex Moyano

Due to very demanding environmental rules, and to the incrementing impurities contents in the processed concentrates, Codelco Norte smelter permanently faces new demands for planning the production program with the present fulfillment of the environmental regulation. Accordingly, the CN smelter along with IM2, developed an impurity distribution simulation model, M-DICE, which predicts the impurities behavior for each of the process units of the smelter under different process configurations and concentrates quality. The development of the M-DICE included the gathering of operational data for the process units of the CN smelter, including temperature, oxygen enriched air, matte grade, etc. Then based on a mass balance for each of the process units involved in the smelter a thermodynamic evaluation was done to derive the arsenic fractional distribution among the condensed (matte/white metal/copper/slag) and gas phases. Then, the validated M-DICE was able to predict the arsenic behavior in the Teniente converter processing complex concentrates with high arsenic content, among others. At present, M-DICE is in its last stage of development, and is expected to be a suitable environmental and process management?s tool for the Codelco-Chile?s smelters.

Jan 1, 2006

By Rodney T. Jones

Mintek has developed and piloted a novel process for the treatment of nickel-copper and PGM (platinum group metal) sulphide concentrates. The ConRoast process is based on the removal of sulphur by roasting, followed by smelting of the dead-roasted concentrate in a DC arc furnace using an iron-based alloy as a collector for nickel, copper, cobalt, and PGMs. The environmental benefits with respect to sulphur emissions are considerable, in that essentially all of the sulphur is removed from the enclosed roasting equipment in a continuous stream of SO2 of an appropriate strength for feeding to a sulphuric acid plant. This process allows great flexibility with respect to the selection of ore types, and does not impose limits on the minimum quantities of contained base metals or sulphur, and can tolerate very high contents of chromite in the concentrate. The furnace alloy is water-atomized prior to leaching. Iron may be rejected from the alloy hydrometallurgically, by precipitation as hematite for example. The ConRoast process achieves very high metal recoveries, and produces high-purity metals, and a clean high- grade PGM concentrate.

Jan 1, 2002

By C. J. Newman

In January 1999, a redesign of the Kennecott Flash Converting furnace settler was initiated to enhance furnace integrity and extend furnace life. This furnace uses Kennecott-Outokumpu Flash Converting technology to produce copper directly from copper matte. A detailed assessment was made of all technology available around the world before making a decision on the design features to be incorporated in the new design. The new design includes the following: redesign of all sidewall cooling elements to include the latest cooling element technology; redesign of the furnace hearth to include a stadium hearth at the reaction shaft end of the furnace; redesign of the furnace hearth to include a stepped hearth design adjacent to the furnace sidewalls; addition of flat settler roof cooling elements .around the reaction shaft; replacement of reaction shaft transition elements with an improved design and improvements to the furnace cooling element monitoring systems. The Flash Converting furnace was shut down on a planned basis in July 2001 to implement these improvements after 29 months of operation, converting more than 1,000,000 tonnes of matte. During the 30 day shut down, the improvements were successfully completed, with furnace start up in August 2001

Jan 1, 2002