Search Documents

By Brian P. Atkin

The NISOMI-81 opaque mineral searcil and identification system uses quantitative color values (Pe, dA, y) and VHN as its determinative para-meters. The system is designed to operate on a Radio-Shack TRS-80 micro-computer which is interfaced to a motorised diffraction grating mono-chromator (WILSCAN). Using an interfaced monochromator/photometer combination a typical identification including the measurement of the photometer data on both specimen and standard, calculation of color values and a computer search takes about 6 minutes. The data file contains 240 minerals at present but can easily be expanded as reliable new data become available.

Jan 1, 1982

By Jing Lin, Yuan Xu, Qingcai Liu, Dengfu Cheng

"Smelting reduction technology has been developed greatly in recent years. But one of the key problems for this technology is about the refractory that used as lining material in the molten bath. Investigation and test shown that corrosion rate of refractory was much higher and the corrosion mechanism was much more complexity in the molten bath of smelting reduction with iron bath than that of the blast furnace and rotary furnace technology [l-5]. The corrosion behavior and corrosion rate of Al2OrC-ZrO2 series refractory in the melt of smelting reduction with iron bath have been studied by rotary immersion and quasi-static immersion test in this paper. The major factors that affect the interaction between the melt and refractory were investigated. The test results shown that the corrosion rate of AI2O 3-C-ZrO2 series refractory decreased with the ZrO2 increasing when ZrO2 content was from 3% to 10%. Ferrous oxides content, relative moving speed between the melt and refractory and temperature of the molten bath were the important factors that affect the corrosion rate. But the ferrous oxides concentration was the most important one. The corrosion rate was increased as a linear relation with the rising of ferrous oxides content of the melt. The corrosion rate in the quasi-static immersion was much less than that of the dynamic immersion (rotary immersion) for the Al2O 3-CZrO2 series refractory in the same testing condition. The corrosion mechanism of Al2OrC-ZrO2 series refractory is: graphite oxidized in advance, then interaction between the constituents of refractory and melt taken place and deteriorate layer of refractory and new compounds were formed, the properties of refractory was changed.IntroductionSmelting reduction with iron bath is a typical technology [3, 4, 6]. The obvious features of the melt for smelting reduction technology with iron bath are much higher ferrous oxides and much more complexity melt composition and structure than that of the blast furnace technology [2, 5-8]. The properties of the melt were changed dynamicilly and constantly in reduction process. On the other hand, the behavior of the melt depends on the activity and the reduction rate of ferrous oxides in the molten bath[9]. Because of the high concentration of ferrous oxides in slag and high reduction rate in the molten bath, the corrosion behavior and corrosion mechanism of the refractory lining by melt are an important factor in development of the technology of smelting reduction with iron bath. Up to now, improving refractory quality to anti-corrosion of melt and developing high quality and long term refractory used as the lining refractory materials in the molten bath of the final reduction furnace are also the most important questions for developing smelting reduction technology."

Jan 1, 2000

By Joerg Hammerschmidt, Marcus Runkel, Andreas Wirtz, Kent Pope

"Fluidized bed reactor systems in the minerals industry have been progressively developed and widely implemented over a period of more than sixty years for a multitude of process applications. Their versatility is manifested in calcining, roasting and combustion treatment of minerals including solid fuels. Experiences from metallurgical processes have expanded to new applications in the oil shale processing, biomass combustion and renewable energy sector. This paper focuses on the most important aspects of fluidized bed technology for a variety of Outotec processes. Energy recovery is a major topic for all applications and will be addressed, as well as environmental aspects, particularly regarding the off-gas treatment. Outotec is one of the pioneers of roasting and the fluidized bed process including gas cleaning and sulphuric acid production where applicable. Process development is strongly supported by significant investment in R&D, thus enabling process adaptation and scale-up to meet specific customer/market requirements.Introduction to Fluidized Bed TechnologyThe early days of fluidized bed technology were characterized by the use of bubbling fluidized bed reactors (BFB). This technology was popular for roasting zinc and copper ores. The introduction of circulating fluidized bed technology led to increased plant capacities and improved process control for the traditional processes. Furthermore, the technology has been applied in many other industries, including the renewable energy industry, which will be part of this design and process comparison. The paper starts out with the fundamentals on particle fluidization as the main common design parameter, leading to the importance of heat recovery and offgas treatment.In fluidized reactor systems, the particle concentrations can reach several hundred kilograms per cubic meter of fluidization gas. This high solid concentration leads to large surface areas and enables direct contact of gas molecules with particle surface molecules. Excellent conditions for enhanced heat and mass transfer thus provide nearly ""ideal"" heat exchange conditions and better reaction kinetics. The bubbling bed exhibits a better heat transfer coefficient within the bed in comparison to the circulating fluidized bed (CFB). The different conditions of gas velocities and solid concentrations allowing the classification of fluidization reaction regimes are shown in the Reh diagram in Figure 1."

Jan 1, 2014

By C. -S. Jiang

In most copper refineries, addition agents are added at predetermined rates with no further monitoring of their activity or concentration in the electrolyte. Increasingly stringent cathode quality requirements, and a desire for better process control in tankhouse operations, have recently directed a number of refineries to search for a better addition agent control strategy. Extensive development work has been carried out at the Noranda Technology Centre for the monitor in of glue and thiourea in copper refinery electrolyte using cyclic voltammetry (cv~. Data from both synthetrc and commercial electrolytes are presented, showing the ability of CV to produce reliable and easily identifiable fingerprints of addition agent concentrations in copper refinery electrolyte.

Jan 1, 1991

By Y. Z. Zhang

Electrochemical oxidation of arsenopyrite in ferric sulphate media in the absence and presence of bacteria T jerrooxidans has been investigated for the purpose of understanding the dissolution chemistry of arsenopyrite and the bacteria attack mechanism. Mixed potential, polarization resistance measurements, polarization curve, cyclic voltammetry experiments were conducted in a ferric sulphate medium of 10g/L FeH, temp.25-35°C, pH 1.5-2.5 in the absence and presence of bacteria Tjerrooxidans, respectively. For the anodic process, a two-step reaction sequence is suggested by the electrochemical measurements. The initial step at a low potential is described by:

Jan 1, 1996

By D. S. Barr

Mineralogical, lithological, and metallurgical studies were conducted on various gold ore deposits currently controlled by Freeport-McMoRan Gold Company. Ore samples were first lithologically and mineralogically categorized, then subjected to chlorination, roasting, and autoclaving pretreatments to determine their effects on gold recovery in a subsequent alkaline cyanide carbon-in-leach extraction. The studies indicate that, while organic carbon and sulfide sulfur are the primary refractory components, their effect on process response must be interpreted with respect to the deposit's geology and mineralogy. This approach has proven to be an effective method for evaluating metallurgical alternatives and fore-casting future mill performance.

Jan 1, 1987

By M. Demuth, B. Holleis, M. Potesser, D. Spoljaric

"In 2005, Messer Group established a technology competence centre for metallurgy in Gumpoldskirchen (Austria), with the aim to develop oxygen burners which satisfy today's and upcoming standards of legislation as well as customer requirements. With the assistance of the Development Sponsorship Fund (FFF) of Austria, cooperation with the University of Leoben was agreed on. With the long term experience of the Gas-Warme-Institut ""GWI"" in Essen (Germany) and the University of Leoben, different new burners have been developed.The efficiency of industrial combustion processes can be increased in two ways (which can be seen in Figure 1 ), either by preheating the fuel and combustion air or by adding oxygen. Due to the high 79 % Nz ballast in air combustion, only low flame temperatures can be reached. This results in high heat loss in the exhaust gas, caused by the low combustion efficiency. Oxygen can be introduced into the combustion chamber using different techniques:• Oxygen fuel burners• Direct oxygen injection into the fuel air flame• Underlaying of the fuel air flame• Enrichment of the combustion airIn Figure 2, the theoretical flame temperature for the stoichiometrical combustion of natural gas is plotted as a function of oxygen enrichment. Therefore, it can be concluded that even low enrichment values produce higher flame temperatures and result in higher combustion efficiency."

Jan 1, 2012

By Peter Sylvén, Darwin Morales

Despite being crucial for the smelting process, furnace tapping using oxygen lances has not been considered an operation that brings value. Therefore, these important tools have not seen a significant change in over 100 years. Problems related to the use of oxygen lances include: • Inaccurate tool: causing damages shortening the life of the taphole refractories. • Safety: extended exposure to the operator in an unsafe area of the furnace. • Cost: high oxygen consumption & high lance consumption. • Time consuming and frustrating to connect one lance to another. This paper will suggest a very good solution; new concept thermal lances. We will show how these provide an outstanding performance for a more efficient, faster and cost-effective furnace tapping operation. These new lances are very accurate tools that enable the operator to perform a more controlled operation; resulting in longer taphole life, fewer repairs and less down-time.

Jan 1, 2016

By I. M. S. Moraes

Caraiba Metais has a plant for the purification and the cristallization of the crude nickel sulfate removed from its copper electrolyte purification system. In November 1994, an interdepartmental group was formed to study the Q.F.D. method, through its application on the improvement of the quality of the nickel sulphate hexahydrate. The team, formed with representatives of the following areas : production, technology, marketing, sales, maintenance, laboratory and TQC office, had also the task of checking the applicability of the method to other products of the comp any. This paper describes the main steps such as the survey of customer's demands, the preparation o1 the quality matrix, stablishing the planned quality matrix, the planned and the designed quality, and the consequent identification of the engineering bottlenecks. It is also shown how these bottllenecks were studied and solved. The application of the method allowed the team to identify means of increasing the production capacity by 40%, to improve the intrinsic quality of the product (including packaging), and to increase the reliability of the process.

Jan 1, 1997

By P. N. Anyalebechi

A comparative study of the mechanical properties of automotive steering knuckles produced by three different shape-casting related processes has been conducted. It involved the characterization of the tensile and fatigue properties of aluminum alloy A356 knuckles produced by the vacuum/pressure riserless casting (VRC/PRC), pressure counter pressure casting (PCPC), and the hybrid Cobapress (a casting-forging) processes, in accordance with the appropriate ASTM standards. Surprisingly, the knuckles produced by the hybrid Cobapress process exhibited the lowest strength. For example, the average 0.2% yield strength of the Cobapress knuckles was 31 MPa and 40 MPa less than that of the VRC/PRC and PCPC knuckles, respectively. However, between stresses of 150-200 MPa, the fatigue lives of the VRC/PRC, PCPC, and Cobapress knuckles were comparable. But above 200 MPa, the Cobapress knuckles exhibited the lowest fatigue life. The observed differences in the mechanical properties are attributed to the inherently different microstructures of the different knuckles.

Jan 1, 2009

By Evgueni Jak

Pyrometallurgy is an important sector of modern industrial society actively participating in solving current environmental, economic, materials scarcity and other challenges. Recent advances in analytical methods, experimental techniques, thermodynamic, phase equilibria and process modelling tools provide new opportunities to increase the productivity of pyrometallurgical reactors, the treatment of complex feeds and metal recoveries. Fundamental theoretical models can now be used to make a significant next step towards the development and implementation of computerised models describing real industrial processes—Virtual Reactors, and computer-aided smart-decision-making systems that may be called Pyro-GPS by analogy to GPS; these developments can facilitate knowledge-based improvement and optimisation strategies. The implementation of these improvements require ongoing collaboration between researchers, industry and government.

By Jr. Langhans, J. S. McPartland

"The presence of zinc in cyanide solutions is generally thought to not have an adverse effect on precious metal recovery or recovery rate by heap leach processing. However, analytical interferences of zinc in solution can cause problems in accurately determining and controlling cyanide concentration in the leach solution, leading to increased cyanide consumption. Analytical methods and the chemistry of cyanide in the presence of zinc are reviewed. The effects of solution pH and zinc concentration on the free cyanide determination were evaluated in detail. Use of the standard silver nitrate titration and a modified titration method for controlling cyanide concentration during heap leaching were investigated experimentally. The practical implications of cyanide heap leaching in the presence of cyanide soluble zinc minerals are discussed.IntroductionThe presence of zinc in precious metal cyanidation circuits is not uncommon. Zinc can be introduced into cyanide leach solutions through dissolution of various zinc minerals1>, or through the use of a Merrill Crowe (zinc precipitation) circuit. Zinc minerals typically occur infrequently and in low concentration in gold ores, but are more abundant in silver ores. Merrill Crowe systems are most commonly employed for recovery of precious metals from solution for relatively high silver ores. It is desirable to control the amount of dissolved zinc in a cyanidation circuit for several reasons. Excessive zinc build-up in cyanide leach solution can, under certain circumstances, inhibit precious metal dissolution and adversely affect solution recovery systems. Additionally, high zinc concentrations can lead to excessive in-process cyanide inventories and potentially, to higher cyanide consumption"

Jan 1, 1999

By Tom Lewis

The metal finishing and electronic industries are searching for ways to recycle materials · and reduce costs. The areas of heavy metal waste and water recycling has gained new interests with the potential of impacting the operation's bottom line. Lewis Environmental Services, Inc. has completed numerous heavy metal recovery and effluent recycling projects with its ENVIRO-CLEAN PROCESS for government and private sector clients. This patented process utilizes a proprietary chemically treated granular activated carbon with enhanced heavy metal adsorption capabilities combined with electrolytic metal recovery to produce a saleable metallic product. The process generates no sludge or hazardous waste and the effluent meets EPA .limits. This paper covers several heavy metal removal projects, two fullcscale commercial installations, and one treatability case study.

Jan 1, 2000

By Howard K. Worner

"In a rewarding career spanning nearly two thirds of a century, the author has worked at the frontier of such diverse fields as the creep of metals, structure properties and production of novel dental and surgical materials, molten salt electrolysis for titanium production, greatly improving the productivity of large iron blast furnaces and of oxygen steelmaking. While each of these has given great satisfaction, special thrills have derived from the development of new methods for the continuous production or refining of both ferrous and non ferrous metals. A rewarding segment was the evolution of various aspects of WORCRA technology. Unfortunately, several of these inventions have been ""ahead of their time"". Introduction""I am greatly honoured by the convening of this meeting to recognise my contributions to pyrometallurgy. My appreciation is the greater because this is the third Howard Worner Symposium; the first took place in the University of Newcastle in 1988, close to my 75th birthday. It was arranged by the local branch of The Australasian Institute of Mining and Metallurgy with the theme, ""Frontiers in Pyrometallurgy"". The second was organised by the University of Wollongong in conjunction with the Australian Academy of Science and the Australian Academy of Technological Sciences and Engineering; it celebrated my 80th birthday and, at my request, covered a broad range of topics under the heading of ""Recent Advances in Science and Technology"". Now, this very international meeting on ""Injection in Pyrometallurgy"" has been convened by the G K Williams Co-operative Research Centre for Extractive Metallurgy in my alma mater. I am both delighted and honoured that the cosponsors are the TMS (USA) and ISIJ (Japan).Dr Madhu Nilmani consulted me about the field to be covered and I readily concurred because ""injection"" has been of keen interest to me since the beginning of the 1960s when I began my pioneering work on sequential oxygen (or air) injection into flowing streams for both refining of blast furnace hot metal to steel and for the continuous smelting-converting of copper and nickel."

Jan 1, 1996

By S. Malinov, J. J. McKeown, W. Sha, S. McShane

"A model is developed for prediction of fatigue stress life S-N diagrams for Ti-6Al-4V alloy at different conditions, using Artificial Neural Network (ANN). Different factors which have influence on the S-N diagram are involved as input parameters of the NN, namely microstructure, environment, texture, test/work temperature, surface treatment and stress amplitude. As the output the S-N fatigue diagram is simulated and plotted.The model is based on standard multilayer feedforward neural network. The NN is trained with a comprehensive data set collected from the literature, using Levenberg-Marquardt training algorithm in combination with Bayesian regularisation. A very good performance of the trained Neural Network is achieved. Good correspondence between ANN"" prediction and experimental S-N diagrams is observed. Using the model S-N diagrams for different conditions are predicted and analysed. Graphical User Interface is developed for use of the model. We believe that the model will be important for practical applications in solving various problems on fatigue behaviour of the titanium alloy.IntroductionTitanium and its alloys have an increasing range of applications due to their very good combination of mechanical properties, corrosion and erosion resistance. They are currently finding widespread applications in many industries due to their desirable and versatile properties. Most important among the alloys is Ti-6AI-4Y. Jet aircraft manufacturers are the principal 'consumers of Ti-6Al-4V and it is often specified for critical parts, the failure of which could result in the loss of an entire system. A generic class of Ti-6AI-4V has been developed over the past years and it has become the best understood of all the titanium alloys. The advantages of titanium alloys include: (i) low densities, giving very attractive strength to weight ratios allowing lighter and stronger structures; (ii) superior corrosion and erosion resistance in many environments; (iii) high temperature capability. Although the titanium materials are still considered as expensive materials, for many applications the cost of titanium alloys can be justified on the basis of their desirable properties."

Jan 1, 2001

By Richard B. Diver, Mark D. Allendorf, Daniel E. Dedrick, James E. Miller, Roy E. Hogan, Andrea Ambrosini, Eric N. Coker, Anthony H. McDaniel, Nathan P. Siegel, Gary L. Kellogg

"Converting carbon dioxide and water to hydrocarbons is an attractive option for storing solar energy and, coupled with appropriate CO2 capture technology, for recycling carbon and impacting atmospheric CO2 concentrations. For any process, high solar-to-fuel efficiency is necessary for large scale viability and favorable economics. Thermochemical approaches for solar-to-fuel conversion are potentially highly efficient as they avoid the inherent limitations of photosynthesis and also sidestep the solar-to-electric conversion necessary to drive electrolytic reactions. Solar-driven two-step metal-oxide-based thermochemical cycles for producing the components of syngas, CO and H2, from CO2 and H2O are the basis of the “Sunshine to Petrol” project. Multi-cycle production of both H2 and CO has been demonstrated over several iron- and cerium-based compositions fabricated into monolithic pieces both in the laboratory and at the National Solar Thermal Test Facility. These compositions are being developed for deployment in a unique and continuous solar-driven reactor prototype, the counter-rotating-ring receiver reactor recuperator or CR5.IntroductionThe interconnected challenges posed by increasing global competition for petroleum and the increasing concentration of atmospheric carbon dioxide are now widely recognized. Meeting these challenges requires recognition that although hydrocarbon fuels are ideal energy carriers, they can no longer be thought of as primary energy sources. It is necessary to take the realistic view that our conventional fossil fuels are in fact “stored sunlight” in the form of “sequestered carbon.” This view leads to a search for options to use and store sunlight more directly.Sunshine to PetrolIn combusting hydrocarbons we unlock the energy for utilization, but we also release the carbon to the atmosphere. However, nature teaches us that with an appropriate persistent energy source, e.g. solar irradiation, it is possible to effectively reverse the combustion process and “reenergize” CO2 and H2O back into hydrocarbon form."

Jan 1, 2010

By Hiroshi Hashimoto

For the application of sodium carbonate slag treatment to product high purity copper on an industrial scale, the counter-flow batch process that reduces the amount of utilized slag is proposed from the viewpoint of the post-treatment of slag. Based on the distribution ratios of several impurities between the slag and molten copper determined previously, the effectiveness of this process is discussed using a mathematical model and confirmed experimentally. According to the model, the slag consumption to remove Sb to a required level in case of the counter-flow batch process with 3 reactors is calculated to be around 30 % of that in the case of an ordinary batch process, where pure sodium carbonate is used as a slag at every stage.

Jan 1, 2003

By Michael L. Sorokin

The behaviour of cobalt during processing of nickel raw material is analysed within the Ni-Co-Fe-S-O-SiO2 system using the computer model. For this purpose the thermodynamic parameters for "three-suffix" Margules's equations in Co-Fe-S and Co-Fe¬Ni-O-S1O2 systems were computed! Phase and iso-activity diagrams for Co-Fe-S system, and phase diagrams for the systems Co-O, Co-Fe-O, Co-Ni-O, C-oO=SiO2 and Co-Fe-O¬SiO2 are calculated using the developed computer programs and identified parameters. The diagrams are used to analyze cobalt behaviour at smelting and converting.

Jan 1, 1995

By Atinuke Oladoye, David Esezobor

"Particulate Copper Silicon carbide (Cu-SiCp) composites find application as wear and heat resistant materials in electrical sliding contacts such as in homopolar machines, railway overhead current collector systems where high electrical/thermal conductivity combined with good wear properties is required. However, challenges occur during machining due to the presence of hard reinforcement in the matrix. This may lead to high turnover of tool wear and poor surface finish. The adoption of near-net shape technology to produce such hard-to-machine metal matrix composites and subsequent finish machining with its attendant cost has reported limited success. This paper critically appraises the challenges and opportunities in the improvement of tribological characteristics of particulate Cu-SiC composites and identifies low cost reinforcement material that could be used to improve its tribological characteristics.IntroductionTribology consideration is increasingly becoming a decisive factor in the design and selection of materials for applications involving interacting surfaces in relative motion. The consideration is mainly on the combined effects of friction and lubrication on material's wear integrity and performance amongst other. Annual losses due to tribology in the US industries are estimated at between 1-2% of the Gross National Income [1], in Russia it is about 1-4% of the GDP [2]. Thus, the attributes of tribology has become imperative in modem machinery especially those applications involving sliding and rolling surfaces, and electrical contacts [3- 8].These are readily found in homopolar machines, internal combustion engines, aircraft engines, gears, cams, seals and railway overhead current collector systems [9-12]. In these systems, the dissipation of frictional heat arising from the interacting surfaces as quickly as possible imposes constraints on the choice of materials for such application to prevent softening, plastic and shear flow and the transfer of metal as wear debris onto the interacting surfaces. If these possibilities occur, system performance is compromised and premature failure may result. Materials for these systems are expected to possess high electrical and thermal conductivities, low coefficient of thermal expansion, good corrosion resistance and high melting point [3-8, 13]."

Jan 1, 2011

By William Petruk

The mineralogy of the primary and oxidized ores from the Malanjkhand porphyry copper deposit in India was studied to determine ore characteristics that affect metallurgy, and to assess applicable processes for recovering the copper. Three mineral assemblages were found. One occurs in primary ore, another in moderately oxidized ore, and a thir:d in intensely oxidized ore. Chalcopyrite, the main mineral in the primary ore, is relatively coarse-grained, with grain size increasing as the ore grade increases. High chalcopyrite liberations should be achieved at a relatively coarse grind, and good chalcopyrite recoveries should be obtained. The chalcopyrite, however, tarnishes readily and oXidizes to chalcocite in a relatively short time (several months). The presence of both the tarnished chalcopyrite and chalcocite may affect chalcopyrite flotation and reduce copper recoveries, The moderately oxidized ore occurs in an oxidized cap immediately above the primary ore, and stockpiled primary ore alters quickly to a moderately oxidized ore. Chalcocite is a major copper-bearing mineral in moderately OXidized ore. The concentrator processing this ore should be capable of handling a chalcocite-rich ore. The intensely OXidized ore contains a wide variety of acid-soluble copper-bearing minerals. Leaching may be required to recover the copper from them.

Jan 1, 1987