Search Documents

By J. Daniel Bryant

Deformation processing of rapidly solidified powder alloys presents a technical challenge different in several ways from the processing of ingot based alloys. The metastable phases formed during planar flow casting of aluminum alloy 8009 (FVS0812) must be safe-guarded from high temperature excursions during processing to avoid decomposition; this restriction prohibits liquid phase sintering of particles during consolidation. The development of strong particle-particle adhesion, therefore, relies on the imposition of very large strains during forming operations to insure sufficient mechanical meshing of the aluminum particles and break-up of prior particle oxide boundaries. These strains are generally much greater than those required for metallurgical transformations in ingot based alloys. In an attempt to quantify the deformation required to improve interparticle bonding, the finite element method (FEM) was employed. Preliminary results which predict the metal flow and strain distribution in several workpiece configurations are discussed. These predictions are then correlated to measurements made on experimental subscale forgings. Lastly, experimentally measured quantities which reflect the degree of interparticle bondingg are related back to FEM model predictions.

Jan 1, 1992

By Bowen Li

Andalusite is an excellent raw material for refractory applications due to its high aluminum oxide content and phase transformation to mullite at high temperature. Granular andalusite in particle sizes of about 1 to 2 mm was traditionally utilized for the manufacturing of refractory brick. However, if powder andalusite in micron particle size is utilized in high-alumina refractory products, reinforcement on the refractory brick can be obtained and the sintering temperature can be decreased. The phase transformation of powder andalusite plays a key role for the difference.

Jan 1, 2006

By Jerome P. Downey

The Indium Corporation of America - Colorado School of Mines Indium Separation Technology was evaluated as a potential means of treating smelter flue dusts stockpiled at the Pintlar Corporation property in Kellogg, Idaho. The patented technology represents a method for segregating the contained indium, lead, and other metals in forms acceptable for downstream processing and recovery. Separation is effected by treating the dust with metallic sodium in a bath of molten lead. Process effectiveness was measured by determining the relative distribution of key metals between the bullion and dross products at small pilot plant scale. The study indicated that application of the technology to the Pitlar samples results in a highly efficient concentration of lead in the bullion, while indium is collected in the dross. The distribution of other key metals between the bullion and dross products and the effect of varying selected process parameters are also discussed.

Jan 1, 1994

By Liyuan Chai

In this study, spent grain was used as an adsorbent for the removal of Hg(II) from aqueous solutions, the process parameters such as contact time, solution pH, adsorbent dose, and initial Hg(II) concentration were studied in batch experiments. The initial adsorption process was fast, 91.08% of adsorption occurred within 5 min and equilibrium was reached at around 30min. Adsorption process was found to follow pseudo-second-order kinetics. The equilibrium data were better fitted to Langmuir isotherm than Freundlich isotherm with the maximum adsorption capacity 41.36 mg/g. The structure and component of spent grain before and after adsorption of Hg(II) were investigated using scanning electron microscope(SEM) and energy dispersive X-ray analysis(EDAX), these analysis also confirmed the adsorption of Hg(II) onto spent grain. The results indicated that spent grain had potential as a new inexpensive adsorbent for Hg(II) removal from aqueous solutions.

Jan 1, 2009

By Hui-Gai Li

The fine Ti oxide inclusions precipitated during solidification are favorable for intragranular ferrite nucleation. The oxygen content before solidification affects the composition and size of inclusions. The composition of precipitated inclusions in Mn-Ti alloyed steel was studied by means of thermodynamic calculation and experiment in this paper. The micro-segregation of Mn, Ti and O during solidification was considered in calculation and unidirectional solidification apparatus was employed in experiment to ensure that alloy elements diffused along solidification direction. The results showed that: inclusions are mainly Ti oxide when oxygen content is 10ppm; they are Ti oxide and Mn-Ti oxide when it is 20ppm; Mn-Ti oxide dominates when it is 30ppm. With the increase of oxygen content, the size of inclusions increases. The maximum oxides size is about 3µm from statistical results of experiment.

Jan 1, 2008

By Vladimir Lobanov, Vladimir Skorohodov, Boris Radionov, Olga Makovskaya

"The synthetic sorbents and the activated carbons which are used for the metals extraction from weak process liquors are rather expensive. It is propose to use mineral and synthetic high-porous substances which sharply increased sorption properties by special processing. For achievement the desirable properties sorbents are impregnated by specially prepared solutions. Such solutions should contain the substances or its anionic forms which on the one hand are strong enough fixed in a supporter pores, with another are capable to form the insoluble compounds with extracting metals. Selectivity is provided by chemism of the reagent interactions with extracting metal. Due to the high concentration of a reacting ion in a sorbent phase the capacity and rate of sorption increases. Formed insoluble compound remains in a phase of the sorbent and necessity of its filtration disappears. For synthesis the sulfhydryl compounds which chemical properties allow to increase degree of extraction and capacity of the activated carbon were used. At hydrometallurgical processing of precious metals mineral raw materials the commercial solutions with the concentration of gold from 0,1 to 5 mg/dm3 are received. Commonly gold is precipitated from cyanic solutions by the zinc dust. The sorption methods are widely applicable. But the synthetic sorbents and the activated carbon using to these purposes are rather expensive. Expenses for sorbents even at its regeneration can reach 10-15 % from total expenses of gold extraction from ores. When sorbent regeneration, mostly for carbon, is not provided, this share increases to 30-40 %. Thereupon search of the sorbents combining availability, the sufficient capacity, demanded degree of extraction and the low price is actual. For the specified purpose it is offered to use the mineral and synthetic high-porous materials which sorption properties are sharply rose by special treatment. Among such substances are natural zeolites, silica gel, lignine et al. Similar treatment can improve the sorption properties of sorbents used in practice, particularly, the activated carbons. The simplest treatment of potential sorbents consists in its impregnation by specially prepared solutions. Such solutions should contain substances or its anionic forms - impregnating agents. These agents should be on the one hand strong enough fixed in a carrier pores, on the other hand are capable to form with extracting metals insoluble compounds. The more strong compounds are formed the high degree of metals extraction from solutions. The sorbents with similarly changed properties are named the impregnated sorbents."

Jan 1, 2008

By Julian Johnson

The effect of changing redox potential (Eh) on the high temperature sulfuric acid leaching of Western Australian dry-land nickel laterite ores has been investigated. In particular, the effect of added reductant (sulfur, sodium sulfite) or oxidant (potassium chromate) on Eh, leaching kinetics, metal extractions, acid utilisation and leach residues has been determined. Three separate ores - nonhonitic ores from Murrin Mumn and Bulong, and limonitic ore from Cawse - were used in the study. Sulfur addition varied from 0 to 7.8 kg/t ore. The total acid loading was kept constant at 430 kg/t (Murrin Murrin ore) and 330 kglt (Cawse ore), whilst acid loading for Bulong ore was varied according to the presence of either reductant or oxidant. The extraction of both nickel and cobalt from limonite ore remained unaffected when small amounts of sulfkr were added, but addition of even small amounts of reductant to nontronitic ore decreased both nickel and cobalt extraction. Increased manganese and iron dissolution were observed as the levels of reductant increased, accompanied by a decrease in chromium dissolution. As the iron dissolution increased, free acidity decreased, with a subsequent decrease in nickel extraction. In contrast, addition of oxidant lead to reduced iron and manganese dissolution and slower extraction of nickel and cobalt. Keywords: Limonite, Nonhonite, Eh, Nickel Extraction

Jan 1, 2004

By Jian Li

Corrosion resistance of materials is highly dependent on the microstructure of the specific material. Apart from general corrosion rate measurement using techniques like linear polarization and A.C. impedance, microstructural investigations are frequently needed to identify the root cause of corrosion. Advanced techniques, including scanning electron microscopy (SEM) and transmission electron microscopy (TEM), have been well integrated into routine characterization studies. Other microscopy techniques, including electron probe micro-analyzer (EPMA), Auger, X-ray photon spectroscopy (XPS) and secondary ion mass spectroscopy (SIMS), can provide detailed chemistry information on corrosion products. In recent years, focused-ion beam (FIB) microscopes have evolved into an important microstructural characterization instrument. In this study, corrosion of rebar encased in concrete was studied in great detail using advanced microscopy techniques. Corrosion product on the rebar surface was identified as ferrous oxide with relatively large crystal size. The morphology of this passive layer was thoroughly analyzed, and its formation mechanism is proposed.

Jan 1, 2009

By Reza Kamali, Mohsen Bashiri, Hadi Fanisalek

"Half of the input energy to aluminum reduction cell will be lost as waste heat which could be studied for possible recovery. Since price of energy is increasing and the main production cost in primary aluminum industry is energy, so waste heat recovery consideration will be interesting. One of the possible choices for recovering is from aluminum exhaust gases that needs minimum modifications for reduction cell and has no influence on cell heat balance which is vital for the operation. By using heat exchangers with in-line and staggered tube arrangements which placed before fume treatment plant (FTP) we will be able to recover enough amount of heat. The main challenging problem which is necessary to overcome will be the heat exchanger material and its design because of corrosive and dusty exhaust gases from potroom. In this paper, a desalination system with six effects of evaporator is proposed for producing distilled water by using recovered heat from hot exhaust gases. The calculated amount of produced distilled water is around 27,000 / in this specific suggested desalination plant. The suggested desalination plant is based on Hormozgan Aluminum Company data (Hormozal) in Bandar Abbas, Iran which is constructed by the Persian Gulf.IntroductionWaste heat losses arise both from equipment inefficiencies and from thermodynamic limitations on processes. The exact quantity of industrial waste heat is poorly quantified, but various studies have estimated that as much as 20 to 50% of industrial energy consumption is ultimately discharged as waste heat [1]. In order to achieve a final decision for establishing the waste heat recovery plant in any type of industry, a strong feasibility study is mandatory. Also, we need to remember that the possible amounts of energy and suggested process plant for recovery have to be investigated before starting any feasibility study. This kind of study which is important to be finished before moving to feasibility step is mainly a theoretical study, and was done for the Hormozgan Aluminum Company (Hormozal). In addition to the exhaust gases from the potroom, the exhaust gases from anode baking plant appear to have a better potential for waste heat recovery compared to potroom exhaust gases. The average temperature of exhaust gases from anode baking kiln is 120°C higher than the exhaust gases temperature in the potroom. This needs further investigation in a different study, because this study is just focusing on potroom exhaust gases."

Jan 1, 2011

By Jan Pan, Deqing Zhu, Xianlin Zhou, Yanhong Luo, Zixing Xue

"Magnetic roasting process, aiming at obtaining magnetite concentrate, is the principle method of exploiting siderite as a raw material in iron and steel industry. Study on preparing DRI from siderite through coal based reduction technology is sporadic. To make the process of how siderite is reduced to iron clear, roasted ore reduced from siderite by lignite under different time periods were analyzed. The results indicated that: at the temperature of 1050°C, siderite was rapidly decomposed into magnetite, and further reduced as Fe30r?FeO?Fe, the later step was slower than the previous one. A fracture of particles was found during the process of thermal decomposition and the reduction of newly formed magnetite. As the reduction proceeded, metallization rate of products increased, and the iron grain grew along with time.IntroductionWith the rapid development of economy, China demands more and more iron ores for the iron and steel industry. China has rich iron ore resources, but 97% of them are below 30% in iron grade, many are refractory and unutilized [1], therefore large quantities of imported iron ores are in a desperate need. China imported 686 million tons of iron ore in 2011 (data from the China Customs), accounting for nearly 60% of the total consumption. To guarantee the healthy development of iron and steel industry, domestic refractory iron ores have to be utilized both economically and environmentally."

Jan 1, 2013

By Albert F. S. Seboukens

A 5;6 MVA pyrometallurgical demonstration-scale pilot plant was commissioned at Mintek, South Africa, in 1994, using lead blast-furnace slag and coke as raw materials. The plant included a.d.c. power. supply, two plasma-arc furnaces' and an ISP lead-splash condenser. Slags containing typically 12 per cent zinc oxide and 3 per cent lead oxide are produced as a waste during the smelting of lead in a blast furnace. These slags are a potential: resource for the recovery of lead and zinc. During 1994, about 600 t of lead blast-furnace, slag was proceced through the pilot plant using the Enviroplas process. Zinc and lead oxides were reduced to their respective metals, volatilized, and collected in an. ISP lead splash condenser. Prime Western grade zinc and slags disposable in accordance with current US legislation, were produced. Zinc condensation efficiencies of about 80 per cent were achieved.

Jan 1, 1995

By W. -S. Hwang, R. A. Stoehr, P. Ingerslev

"The flow of molten metal entering complex two-dimensional foundry molds has been modeled using the Simplified Marker and Cell (SMAC) and Solution Algorithm (SOLA) techniques. The molds were for a series of four and three-spoke wheel designs. The computer calculations were compared to physical experiments in which molten cast iron was poured into C02-bonded sand molds. The metal was photographed with a high speed motion picture camera focused through a Pyrex glass window on one face of the mold. To get good agreement between the calculations and the experiments, it was necessary to accurately represent the velocity through the ingate. This was calculated by application of the Bernoulli equation to flow through the feed system. Some difficulties were experienced with mathematical instability, expecially in the three-spoke design with a narrow ingate. This was overcome by using 100% upwind differencing, and over relaxation parameter near 1.0 (i.e. no over relaxation), and variable mesh spacing.IntroductionModeling the flow of molten metal entering molds has the potential for making significant contributions to the design of feed systems. It will supply information to the computer-aided-design systems of the future that will enable the designer to optimize the placement of gates, dimensioning of passages, and designation of casting speeds. Such design criteria have generally been based on application of energy balance (Bernoulli equation) principles to flow in the sprues, runners, and gates. Indeed, this is the easiest way to determine the proper dimensions to give a suitable filling time for a casting of a given size. A number of computer programs, including one by some of the present authors, have integrated such calculations into CAD systems. l Modeling the flow of metal inside the mold cavity requires other techniques that will handle free-surface transient flow. Stoehr and Hwang reported on the application of the Marker-and-Cell (MAC) technique to mold filling problems at the previous conference in this series at Hennicker, N.H. in 1983. 2 Although considerable progress has been made since that time in improving the accuracy, stability, and convenience of these techniques, the shapes to which they were applied remained limited. Also, physical verification of the results of the calculations was limited to water models.The work to be reported in this paper was undertaken with two objectives: (1) to apply these techniques to more complex and realistic shapes, and (2) to verify the results by comparison with flow patterns observed in molten metal poured into actual sand molds."

Jan 1, 1986

By Jorge Alberto Soares Tenório, Viviane Tavares de Moraes, Denise Crocce Romano Espinosa, Franco Alves Lavacchini Ramunno

"The traditional process for recovery of metals from waste electric and electronic equipment (WEEE) usually involves pyrometallurgical processing. However, the application of this technology to processing waste printed circuit boards (WPCBs) might lead to the formation of dioxins and furans, due to thermal degradation of flame-retardants and polymeric resins present in the board substrate. Therefore, this paper proposes a hydrometallurgical route for the recovery of copper. The acid leaching behavior of copper has been investigated at three different temperatures (25°C, 50°C and 75°C) with and without the addition of an oxidizing agent (hydrogen peroxide - H202). The dissolution kinetics for acid copper leaching was calculated based on chemical analysis by ICP-OES (Inductively Coupled Plasma - Optical Emission Spectroscopy). At 50°C with 1 mol/L H2S04 added 10 mL H202 (30%) each half hour under pulp density of 1 g I 10 mL, 100% of copper was extracted after 3 hours. The dissolution kinetics of copper with H2SO4-H2O 2 followed 1 - (1 - X)113 =Ket, i.e. chemically controlled reaction model.IntroductionThe information regarding the generation of waste electric and electronic equipment (WEEE) are still difficult to obtain because the estimates should take into consideration the historical production and sale of various products and the rate at which they reach the end of their life cycle, whose duration depends on the behavior of consumers [1]. Thus, the estimated overall WEEE generation varies between 25 and 50 million tons each year, which corresponds to more than 5% of all municipal waste generated [2], and this amount will increase at a rate of 3 to 5% per year, approximately three times faster than other individual types of waste [3].Printed circuit boards (PCBs) are essential parts of electric and electronic equipment (EEE), being found in virtually all electronic products, as well as in weapons systems [4]. A PCB is a basic component, which consists of a board where copper tracks are deposited. While the board behaves as an electrical insulator, the tracks connect electrically the various components attached to the board [ 5]. In addition to glass fibers, paper and resins, the PCBs contain significant amounts of metals, such as copper, iron, nickel, lead, stain, silver, gold and palladium [6]. In general, the weight fraction of metal is around 28% and the remainder of the boards is composed of plastic (19%), bromine (as flame retardant - 4%) and ceramic material (49%) [7]."

Jan 1, 2014

By J. M. Demarthe

MINEMET RECHERCHE (IMETAL Group, formerly Le Nickel-Penarroya-Mokta) has studied on a laboratory scale and patented a new process to recover metal values -copper- from sulphide ores and concentrates. It combines a cupric leaching, solvent extraction and copper sulphate electrowinning according to the main following steps - A direct and selective leaching of copper sulphide ores or concentrates at atmospheric pressure with cupric chloride to form cuprous and ferrous chlorides and elemental sulphur. Pyrite remains in the sulphur residue. - The leach solution is separated into two parts -In the first one, air is injected to precipitate iron as goethite. The oxidation step can be easily realized at atmospheric pressure by maintaining an excess of cuprous and-ferrous chlorides in the liquor. Copper is extracted from the second part as cupric ion by an LIX reagent. Direct injection or air in the mixing chamber maintains good extraction conditions, so that only one mixer settler is required. - Iron, in the form of ferrous ion, is not coextracted. - Copper is stripped from the organic phase, transferred into a sulfuric phase and sent to sulphate electrowinning cells, which are now conventional in copper metallurgy. - Only electricity and air are required. After a feasibility study, the next step will be to develop it on a pilot and commercial scale.

Jan 1, 1976

By J. Szekely, S. Rhee

"A mathematical formulation has been presented to describe heat and fluid flow phenomena in CVD operations. In the statement of the problem, which included consideration of plasma enhanced CVD systems, emphasis was placed on identifying the parameters which play a key role in determining the rate and the spatial uniformity of the deposition process. This was done both through the appropriate dimensionless groups and by presenting an extensive set of computed results. The main conclusions that may be drawn from this work are that the deposition rate will be inherently non-uniform for atmospheric CVD systems; this may be somewhat ameliorated by inclining the susceptor or changing the vessel contours. Operation at greatly redeced pressures and for PECVD systems will give a much more spatially uniform deposition rate.1. INTRODUCTIONIn recent years, there has been a growing interest in chemical vapor deposition techniques for the preparation of thin films for semiconductor, photovoltaic applications and for coatings in general, as evidenced by numerous journal articles and symposium proceedings devoted to this topic (1-6). An interesting variant of this technique is to perform the deposition in a plasma or glow discharge at low pressures because this technology obviates the need for the thermal decomposition of the precursor at the substrate surface and permits operation at greatly reduced temperatures (7-10).By far, the largest portion of the reported work dealing with both these aspects of the technology has been concerned with the characterization of the deposit, quite properly so. However, in more recent times it has been realized that the transport aspects of these processes are also deserving of attention because the understanding of heat flow, fluid flow and diffusional phenomena may provide the key to the solution of problems associated with obtaining uniform deposits and the proper scaling of laboratory measurements in order to design industrial CVD systems."

Jan 1, 1986

By K. C. Mills, P. N. Quested, A. P. Day, R. F. Brooks

"Methods have been developed to measure the physical properties of molten materials relevant to the fluid flow in high temperature processes. Data for the densities, viscosities and surface tensions of Al-, Ni- and Fe-based alloys are compared with (i) values for the pure metals and (ii) estimated values obtained from models making use of chemical composition of the alloy. Experimental values for metallurgical slags are also given and compared with estimated values.1 IntroductionPhysical property data has proved very useful in improving process control and product quality. For instance, in the continuous casting of steel the viscosity (TJ) of the mould flux is important since it determines (i) the optimum casting conditions, nVc = 2.5±1 dPas (m min-1) where V c is the casting speed and (ii) the level of slag entrapment (which leads to inclusions) in the metal. Thus data for properties like viscosity are exceedingly useful in understanding the process and the problems encountered and the causes of defects and problems.Another interesting development which has helped to increase our knowledge of processes and improve process control and product quality is the development of mathematical models of the fluid and heat flow in the process. These models have been developed to the stage where one of the prime requirements is for good physical property data for the industrial materials involved. Recently, Oxley [1] has shown that the use of reliable, experimental, property values for the commercial alloy in a commercial software package produced a significant improvement in the prediction of casting defects. Thus reliable property data are required for liquid metals but also for (i) liquid slags since many processes involve the use of a slag to refine and protect the metal or to lubricate the mould and (ii) refractories, sand and investment moulds."

Jan 1, 1999

By G. Gomathi, K. Asokan, K. Subramanian

An electrochemical reactor with anode and cathode chambers separated by a composite perfluoro polymer cation exchange membrane was designed, fabricated and used for the reduction of dissolved carbon dioxide under ambient conditions to formate. The flow reactor enhanced the mass transfer of carbon dioxide compared to the batch reactor. Experiments were conducted using two different perfluoro polymer membranes - Nafion 961. Efficacy of CO2 reduction on various cathode materials (Cd, Pb, Sn and Zn plated stainless steel woven mesh) were determined. Optimum values of flow rate and current density were evaluated for the energy efficient formation of formate in aqueous KHCO3 (pH 7.5-8.5) buffer solutions.

Jan 1, 2008

By Jeffrey W. Fergus, Shiqiang Hui

"Aluminum is an important alloying addition to the zinc used in the hot-dip galvanization of sheet steel to control the properties and appearance of the resulting coating. Optimization of the galvanization process requires control of the alloy concentration which can be improved through the use of chemical sensors. Aluminum sensors based on molten electrolytes are commercially available but are not widely used because of their high cost. One approach to reducing the cost is to use a solid electrolyte which can simplify the sensor design and thus reduce the cost of fabrication. In this paper, the development of an aluminum sensor based on a solid fluoride electrolyte, specifically magnesium fluoride, will be described.IntroductionThe concentration of the zinc bath used in hot-dip galvanization affects the galvanization process as well as the properties of the resulting coating. Thus, accurate in situ measurement of the alloy composition can be used to improve process control. This paper describes a solid-electrolyte-based aluminum sensor for monitoring the bath composition during hot-dip galvanization."

Jan 1, 1997

By G. Taylor, S. Bounds, G. Moran, M. Cross, K. Pericleous

"A variety of interacting complex phenomena takes place during the casting of metallic components. Here molten metal is poured into a mould cavity where it flows, cools, solidifies and then deforms in its solid state. As the metal cools, thermal gradients will promote thermal convection which will redistribute the heat around the component (usually from feeders or risers) towards the solidification front and mushy zone. Also, as the evolving solid regions of the cast component deform they will form gap at the cast-mould interface. This gap may change the rate of solidification in certain parts the casting, hence affecting the manner in which the cast component solidifies. Interaction between a cast component and its surrounding mould will also govern stress magnitudes in both the cast and mould - these may lead to defects such as cracks.This paper presents a multiphysics modelling approach to this complex process. Emphasis will be placed on the interacting phenomena taking place during the process and the modelling strategy used. Comparisons with plant data are also be given."

Jan 1, 1999

By Leonid M. Lerner

High temperature aluminum Alloy 8009 is a rapidly solidified/powder metallurgy aluminum-iron-vanadium-silicon alloy. This alloy in combination with hard oxide aluminum film has unique engineering properties which may recommend its use in compressors and impellers for aerospace applications. Various anodizing processes (including Sanford Low Voltage DC+AC Process) for these task will be evaluated and normal chemical composition, physical properties, and macrostructures of 8XXX aluminum alloys will be presented.

Jan 1, 2006