Search Documents

By R. Padilla

A thermogravimetric study has been conducted to follow the decomposition and volatilization of arsenic from enargite concentrate in nitrogen and slightly oxidizing atmospheres. Temperature has a large effect on the rate of volatilization of arsenic. Fractional volatilization of arsenic as high as 98% were obtained in less than 60 min at 650°C in nitrogen atmosphere, while in slightly oxidizing atmosphere the same volatilization could be achieved in 30 min. It was found that arsenic volatilizes as sulfide in nitrogen atmosphere and as 4xture of sulfide and oxide in atmospheres containing 1% oxygen. By using the pore blocking and the first order kinetic models, apparent activation energies of 213 and 200 kJ/mol for the temperature range of 780 - 900 K and 205 and 184 kJ/mol for the temperature range of 900 - 985 K were determined for enargite and copper concentrate, respectively.

Jan 1, 1997

By K. Adham

"Fluidized beds are utilized in a wide range of high-temperature applications throughout the metals and materials industry. Their main advantage is the fast and uniform heat and mass transfer between the hot combustion gases and the particulate solid feed. A further benefit can be the lowering of the processing plant's energy consumption, through heat recovery from the fluid bed processes used for solids heating. Here, the enhanced energy efficiency of fluidized systems is investigated and the modeling results are discussed for three configurations: the flash tube, the single bubbling bed and the multi-stage fluid bed. Key thermal design aspects of each system are identified based on results from process simulations, in order to benchmark their main operating features and overall energy efficiency. Suitability and applicability of each configuration is also discussed based on a number of process and material property considerations.IntroductionCombustion based heating of particulate solids is commonly done using three different types of fluidized beds. The flash tube (FT) is similar to a hot pneumatic transport system. The single-stage fluidized bed (FB) typically uses in-bed combustion. The multi-stage fluidized bed (MSFB) can have two or more stages stacked into a tower.Flash tube (FT) suspends the incoming solid charge in a high-velocity stream of hot combustion gases. To maintain the solids suspension in the FT, two parameters are required: high velocity for elutriation of the particles and adequate solid-to-gas ratio for avoiding high pressure drops and solids drop-out [l].The fluid bed (FB) works at much lower velocities than the flash tube. Therefore, most of the solids are not conveyed in the gas stream, but are only suspended in a liquid-like manner. At minimum fluidization velocity (Umr), the gas flow exerts just enough force on the solids to keep them suspended in place [2].Multi-stage fluid bed (MSFB) heats up the solids as they are transferred from an upper bed level to a lower one, counter-current to the rising flow of hot gases generated at the lowest stage. As the temperature and volumetric flow of the gases decrease from bottom to the top stage, smaller bed diameters can be used in the energy recovery stages [3]."

Jan 1, 2014

By V. A. Shumsky, I. P. Polyakov, N. M. Ospanov, M. A. Lyamina, N. N. Ushakov

Studies on the kinetics of the competitive processes of PbS volatilization and PbS oxidation, as applied to the heat and mass transfer conditions in the flame of the Kivcet furnace, revealed that the rate-determining factor is the supply of heat. Therefore, low yields of fume in the autogenous flash smelting of lead sulphide feeds are noted despite the high volatility of PbS at 1,300-1,400°C. Dust formation in the autogenous flash smelting of Kivcet-smelters does not exceed 5-7%, of which fumes amount to ~ 80%. Using extra fuel during autogenous smelting involves the mismatch of the sulphide oxidation rate and the release of heat in the flame, and increases the fume yield. This is a major cause of the high dust formation in pilot plant trials. The analysis of dust formation in the Kivcet smelting of oxidized lead feeds in an industrialscale smelter shows an overall increase of dust formation (up to 10% of the feed), with fumes constituting ~ 80% of the dust. A pronounced increase of the zinc component of the fumes is also noted. Lead

Jan 1, 2000

By Rodney J. Ishak

The reduction of Mn3O4 to MnO has been investigated in a thermobalance apparatus, The charge was composed of manganese ore (decomposed by heating/calcination or pre-reduction to mainly Mn3O4) and coke. The material was charged to a crucible, which was suspended in the balance. CO-gas was distributed through a grid in the bottom of the crucible. Two sizes of ores were used; 2.4-4.8 mm and 6,7-9.5 mm. Coke particles were in the size range 4.8-6.7 mm. Experiments were conducted in the 900-1100°C temperature range. The composition of the product gas was monitored continuously. External mass transport between bulk gas and particle surface does not seem to limit the rate of reduction. Assuming that both diffusion through product layer and chemical reaction at the interface between MnO and Mn)04 are rate controlling, the data was tried both in a shrinking core model and in a grain model using regression. The grain model gives the best physical description of the process, because the reactant is in fact a porous medium. With this model the effective diffusivity was calculated to be in the 1.5-6.10.5 m2/s range. The pore size was mainly between 0.1 and 10 um,

Jan 1, 2003

By Barry T. Kilbourn

A dominant characteristic of many derivatives of the lanthanides is stability at high- temperatures. Combine this with novel solid-state behavior under those conditions and there is the potential for new materials that can not only improve existing applications but also help create new technologies. These property themes will be traced through new uses ranging from efficient energy generation and raw material conversion to control of environmental emissions and temperature measurement. Conducting ceramics, methane conversion catalysts, sulfur oxide capture agents and phosphor hosts will be described. Some categories will account in the future for significant lanthanide consumption whereas others will remain commercially negligible but technologically vital. All uses will illustrate the versatility of those elements inappropriately termed rare.

Jan 1, 1992

By Stella Agatzini

Column leach tests were conducted to evaluate the amenability of poor Greece nickel laterites to heap leaching with dilute sulfuric acid at ambient temperature. The ore tested was a limonitic laterite with less than 1 % nickel and it was subjected to a suitable pretreatment with water prior to it being loaded into the columns, following findings of preliminary research work. The acid solution was recycled after suitable pH adjustment. Factorial designs were used to determine the effects and interactions of the following factors: sulfuric acid concentration, ore column height, ore grain size and ratio of leach solution volume to the ore quantity. The response which were investigated included nickel and cobalt recoveries, codissolution of iron, calcium, magnesium, aluminum, chromium and silica and also sulfuric acid consumption. Experimental error was also detennined. The tests showed that a nickel recovery of 88% could be achieved in 60 days.

Jan 1, 1993

By G. Cifuentes

It is known that the cathode purity and the electrolyte treatment are affected by the solids present in the electrolyte. Anodic slimes properties (e.g., chemical composition, crystalline composition, sedimentation) were studied in copper electrorefining. These properties were modified through anodic composition and current density. In this investigation, we have worked with anode material from the Ventana Smelting, Hernan Videla Lira Smelting (ex - Paipote) of ENAMI (National Mining Company) and El Teniente Smelting of CODELCO-Chile (National Corporation of Copper of Chile). The characterization of the anodic slimes was done as a function of current density and anodic composition.

Jan 1, 1999

By P. G. West-Sells

Recovery of gold from thiosulfate leachates can be accomplished by adsorption of the gold thiosulfate complex by a strong base resin. Two of the most significant impurities that can decrease this gold adsorption are tetrathionate and trithionate, which are produced as oxidation products of thiosulfate during gold leaching. This paper investigates gold adsorption on a strong base resin (Purolite A500C) as a function of the concentration of these impurities. It is shown that concentrations of tetrathionate and trithionate as low as 150 mg/L can decrease gold loading by an order of magnitude, and that of the two ions, tetrathionate has a stronger detrimental effect. The resin and solution gold concentration profiles were successfully fit using a Freundlich isotherm, which further shows the strong effect of tetrathionate. To counteract the decrease in gold adsorption by tetrathionate, a novel process was proposed. Sulfite was added to the solution to oxidize tetrathionate to trithionate, and a nitrogen blanket was added to ensure that no further oxidation of thiosulfate could take place. It is shown that by incorporating this process, gold adsorption was doubled from both synthetic and real gold thiosulfate leachates.

Jan 1, 2003

By R. K. Hill

The Hidalgo Smelter successfully reduced operating costs by 25% compared to the previous two years through a focused holistic approach to development of its entire workforce. The first phase involved basic team training skills for natural work teams. The second phase provided leadership training via breakthrough education to 40 of the smelter leader-both hourly and salaried. The third phase stretched out the teams training to include rewards for performance that resulted in hourly teams converting to salaried status-part of a company wide initiative. The fourth phase saw 1998 become the "Year of Safe Cost Reduction" where 7 breakthrough projects focused on different areas of expenditure. Implementation of lean manufacturing as a tool for teams to truly get their arms around what they controlled, introduced accountability and responsibility for operating results at the team level. This will allow the release of experienced supervisors from this role, to a pool of technical expertise, where our future breakthroughs will be designed and implemented.

Jan 1, 1999

By Zviad Kovziridze

Structure of celsian ceramics in BaO-Al2O3-SiO2system is studied with electron microscope in the entire temperature region of baking interval. The process of the pores filling and the full consolidation of material growth at comparatively high temperatures of baking intervals are described.

Jan 1, 2006

By Patricio Barrios

This paper discusses the revamp and expansion of Atlantic Copper's (formerly Rio Tinto Metal) copper smelter located at Huelva, Spain. The plant was expanded from 150,000 to 270,000 tpy new copper in anodes, and from 133,000 to 215,000 tpy cathodes. Lurgi successfully executed this contract on a lump-sum, turnkey basis in just 19 months. The Lurgi on-site task force performed this work in close cooperation with Atlantic Copper's personnel, with a minimum of disruption in the plant's ongoing operation. The contractual performance parameters were achieved to the client's satisfaction shortly after the mechanical completion of the respective plant sections.

Jan 1, 1998

By Akira Yazawa

Oxidic dissolution loss of metal in slag is discussed thermodynamically in terms of oxygen potential, activity coefficient and equilibrium constant. To understand basic principle, regular solution model is applied for model calculation of the activity behaviour of metal oxide in FeO-SiO2-CaO slag, and effects of slag composition, temperature, and basicity of oxide on dissolution loss are demonstrated. As: a simplified but practical conclusion, the dissolved metal loss in slag is inversely proportional to activity coefficient of metal oxide, and also to FeO content in slag when amount of slag is taken account.

Jan 1, 1994

By Shaolong Chen

Feeding dry sulfide concentrate into smelting furnaces enhances process performance and reduces the energy consumption and exhaust gas flow. Direct heated rotary dryers and flash dryers have being replaced by rotary steam dryers featured by very low wear rate of the pipe heating elements and long maintenance interval. Impact of the drying processes on the environment receives more and more attention as the emission legislation tightens. In this regard, environmental factors such as SO2, CO2, dust and gas flow among rotary dryers, flash dryers and steam dryers were compared. Selection of a rotary steam dryer for copper and nickel concentrate drying would be an ideal solution to reduce the pollution of exhaust gas, as drying is achieved by indirect contact to the steam at relatively low drying temperature and as the off-gas contains almost only water vapor and air. The emissions can be significantly reduced and only small and simple off-gas handling units are needed.

Jan 1, 2006

By Yanhui Liu, Xuewei Lv, Chenguang Bai

A thermodynamic model for determining the surface tension of molten slag by considering the surface tension and molar volume of the pure oxide component, and their ionic radii was extended to the slag bearing high TiO2 (varying from 80 to 67%) at 1973 K. The iso-surface tension curves for the FeO-TiO2-Ti2O3 ternary system at 1973 K are almost parallel to the FeOTi2O3 line. TiO2 plays a role of surface-active solute, and its surface-active effect is attenuating with increasing the TiO2 content. The iso-surface tension curve shifts away from the TiO2 corner, indicating that the surface tension of the ternary slag decreases along with the addition of SiO2. The reasons include the addition of SiO2 with lower surface tension and the decrease of the total ion moment at the surface. Both CaO and MgO can bring about that the iso-surface tension curve shifts towards the TiO2 corner, indicating that the surface tension of the ternary slag increases along with the addition of CaO or MgO. CaO has a more pronounced effect on increasing the surface tension of the ternary slag than MgO at an equimolar amount addition. The increase of the surface tension results from both the compositional change and the variation of the slag structure.

Jan 1, 2015

By E. García-Ramos, P. Flores-Sánchez, E. G. Palacios, B. Zeifert, A. Romero-Serrano, M. Hallen-López

Chromium containing slags from stainless steelmaking may eventually be leached by acidic environments, therefore they should be treated before being stockpiled or land filled. In this work, synthetic slags were prepared and the effect of CaO/SiO2, Cr2O3, MgO and Al2O3 contents on the stability of the mineralogical species formed was analyzed. The morphology and composition of the slags were analyzed by XRD and SEM-EDS, whilst their chemical stability was evaluated by leaching with an aqueous acetic acid solution. It was found that CaCr2O4 and CaCrO4 are present in slags prepared with neither MgO nor Al2O3. The Al2O3-based slags mainly produced Ca2Al2SiO7 and the Cr(VI)-containing oxide complex Ca4Al6CrO16, whilst MgO-based slags produced MgCr2O4 as main mineralogical species. Additionally, Eh-pH diagrams for the Ca-Cr-H2O and Mg-Cr-H2O systems at 25 °C were constructed. The lowest Cr concentration levels in the leaching liquors corresponded to MgO-based slags owing to the stable binding of Cr in spinel with MgO. It was also observed in the Al2O3-based slags that increasing the slag basicity from 1 to 2 the leachability of the slags are notably increased.

Jan 1, 2008

By Dinabandhu Ghosh

The stability diagram of the ternary system Ti-C-O is drawn in the present work for four temperatures, 1473 K, 1573 K, 1673 K and 1873 K, showing the stability fields of TiC, Ti, TiO, Ti2O3 and TiO2. An analysis of the system reveals that it is not possible to produce Ti in a carbon-saturated system; instead, the stable product is TiC. However, Ti can be an equilibrium product in a carbon-unsaturated system at prohibitively low values of pCO and pCO2; for example, at 1873 K, these limiting values are: pCO = 10-6.76 atm and pCO2 = 10-13.36 atm, which, when exceeded, produce TiC and TiO respectively. The magnesiothermic reduction is examined through the stability diagram (log pO2 vs. 1/T) of the system Ti-Mg-O, drawn for a number of pMg values, presenting the pairwise stability fields such as Mg(l) + Ti(s), Mg(v) + Ti(s), MgO(s) + Ti(s), etc. The diagram shows that magnesium reduction of TiO to Ti is possible only at T < 1641 K with pMg = 1 atm and only at T < 1569 K with pMg = 0.5 atm. An experimental scheme for Mg vapor reduction of TiO2 is proposed in which an argon stream is passed over a Mg(liquid) evaporator at temperature T1 (say, 1234 K); the resulting Ar-Mg mixture at 1 atm is subsequently flown over a bed of TiO2 at temperature T2. A thermodynamic analysis establishes that complete reduction to Ti is possible and that the best results are obtained when T1 = T2.

Jan 1, 2006

By T. Iriyama, Y. Fujita, R. Omatsuzawa, T. Nishio, N. Okochi

Sm-Fe-N hard magnetic materials are good candidates for high performance bonded magnets. Rapid-quenching method should be highly favorable for the fabrication of isotropic magnet powder with high coercivity. We report here the magnetic properties of Sm-Fe-N powders produced by a few kinds of rapid-quenching processes. Sm2Fe17 powders were prepared by gas-atomization (GA), rotating-disk atomization (RDA), or melt-spinning (MS) method. The Sm2Fe17 GA powder had dendritic solidification structure, while the RDA powder had micro crystalline structure with size of 3-5 µm. Coercivities (HcI) of their nitrides were 56 (for GA) and 217 ka/m (for RDA). The H cI of nitrided Sm2Fe17 MS powder with wheel velocity (V5) of 5-20 m/s, which had also microcrystalline structure, was 53 to 509 Wm. These coercivity values are not sufficient for bonded magnet applications. From the study of additive effects, it was found that C, C-Si, C-Ga, or C-Al addition decreased the crystal size of quenched Sm2Fe17 powder. Consequently, high coercivity was obtained; the HcI of nitrided Sm2Fe1C1Si1 MS powder with V5 of 10 m/s was 898 kA/m, and 708 kA/m for the nitrided Sm2Fe15C1Si1 RDA powder. The compression-molded bonded magnet made from Sm2Fe18Si0.1Nx MS powder showed a high (BH)max of 82.7 kJ/m3.

Jan 1, 2000

By T. Kimura, H. Ohba

"Much effort has been made to reduce the energy requirement in zinc electrowinning. In order to keep energy consumption low, either to make cell voltage low or current .efficiency high is necessary. Decrease of cell voltage practically depends on how to reduce ohmic resistance in the electrolyte and the anode crust. To realize these, new concept was proposed and the pilot plant has been operated. The space between a cathode and an anode is halved by utilizing the frame insulator. With these frames the anodes and cathodes compose of a unit of electrodes, and this unit is handled by newly designed electrode handling machine (E.H.M.). The process includes lifting up electrodes, expanding the space between a cathode and an anode, cleaning them, stripping the deposited zinc and returning the unit to the cell. As a result, cell voltage is kept as low as calculated and predictable energy reduction has been achieved. IntroductionIn the recent trend of a rapid appreciation of the Japanese yen, Akita Zinc Refinery of Mitsubishi Metal Corporation has been confronted by problems of relatively high operating costs. In order to compete with other overseas zinc refineries, it is necessary to reduce the cost of zinc production, especially the cost of electric power which now accounts for .up to 35 % of the entire cost of production. Three fourth of the electric power used at Akita Zinc Refinery is for the electrolysis. Therefore it is extremely important to reduce the cost of electrolysis.There are two possible measures for solving the problem; one is to use more nighttime electricity taking the advantage of its inexpensive power price, and the other is to reduce electric power consumption.As a part of a rationalization plan carried out in 1986, Akita Zinc Refinery increased the number of operating cells. As a result, when nighttime electricity is used, the silicone rectifier has been able to operate at full capacity. Moreover, by new schemes of ""increase of area for electrodeposition by ralslng the liquid level of electrolyte"" and ""increase of the number of electrodes in each cell"", current density could be lowered and as a result, the electric power consumption has been improved. In order to raise nighttime ratio even higher, installation of an additional rectifier and cells would be required."

Jan 1, 1988

By Boxun Lu, Juan Wei, Kun Chen, Wanlin Wang, Lejun Zhou

"Slag system is an indispensable part during the continuous casting process, and playing various important roles like absorbing inclusions, modifying heat transfer rate, preventing oxidation of molten steel, etc. to ensure the smooth process and excellent slab quality. However most slags contains more than 8% fluorides which tend to introduce a series of environmental and health problems. This study involves the research of the removal of fluorine through the chemical composition optimization. Through the studies of CCT, DHTT, XRD and SEM, it has been successfully founded that the crystalline phase of Ca11Si4B2O22 discovered in this study shows very similar crystallization property as Cuspidine (Ca4Si2O7F2), which is the most important crystalline phase in the current fluorine bearing slags. Moreover, the optimized free/low fluorine slag shows the opportunity to replace conventional high-fluorine mold slag for casting medium carbon steels that is regarded as the bottleneck of green slag development for continuous casting.IntroductionMold flux has been widely used in continuous casting to control heat transfer, lubricate the strand, absorb inclusions, provide insulation and prevent oxidation of the molten steel[1-3]. It usually contains fluorides, like CaF2, NaF etc., which are used to control the viscosity and solidification temperature of mold fluxes [4-5]. However, the presence of fluoride leads to corrosion of equipment, serious environmental pollution (toxic volatiles and water pollution), and high processing cost of cooling water[6-7]. Therefore, the study of low or free fluorine mold flux is of interest and attracts worldwide attention.S. Y. Choi et al. [4] used B2O3 as a substitute for cuspidine in steel B2PB2) however, B2O3 content was extremely high (up to 30 w%). Other studies have investigated F-free mold flux by adding or optimizing components as MgO, Li2O, B2O3 et al[8-11]. However, most of these focused on the melting and viscosity issues or for low or ultra-low carbon steels, where crystallization tendency is not significantly strong. Very few studies regarding to the development of low/free Fluorine mold flux for casting medium carbon (MC) steels have been conducted, due to the difficulty of the crystallization and heat transfer control without the formation of cuspidine."

Jan 1, 2014

By L. E. Murr

Preliminary studies of bacterial attachment to MoSp (molybdenite) have indicated a low correlation between dislocation density in the (0001) basal plane and the density of attached microbes. In the present investigation, poly- crystalline thin sections of CuFeSp (chalcopyrite) have been ion-etched or carefully comminuted to electron transparency and observed in the transmission electron microscope. The thinned test sections were then immersed in a culture solution in which bacterial attachment occurred. The attached bacteria were biologically stained in a uranyl acetate solution and the entire thin CuFeSp sections or tiny particles containing thin, electron transparent edges with bacteria attached were observed in the transmission electron microscope, allowing the coincidence of bacteria and their density to be directly observed in relation to lattice dislocations and crystallographic orientations of the exposed surfaces. This technique has the advantage of exposing crystallographic orientations where dislocation lines intersect the free mineral surface, and the emergence sites of dislocations could in principle be directly investigated as a possible preferential attachment site for bacteria. Bacteria morphologies were also extensively observed in the scanning electron microscope. The implications of the results are that although a strong correlation between dislocation density and distribution and bacterial attachment, density, and distribution has not been established, systematic multiplication of dislocation densities in crystalline mineral particles to be leached could enhance leaching rates by increasing the reaction rates as well as the density of attached bacteria at crystalline, metal-rich phases. Techniques for dislocation production in mineral and ore bodies and the particular implications in chalcopyrite leaching are discussed in relation to in-situ leaching where comminution is attained by explosives and the generation of strong shock waves in an ore body. The present study demonstrates the use of microanalytical and microscopic techniques in the investigation of fundamental microstructural phenomena in hydrometallurgical processes.

Jan 1, 1976