Search Documents

By B. Ozturk, K. Ito, R. J. Fruehan

"A simulation model for bath smelting processes for the production of iron was developed which predicts the coal, flux, ore, and oxygen consumptions and the off gas volume, temperature and composition. The model is comprehensive in that it takes into account all of the important variables including coal composition, metal composition, ore composition, slag basicity, post combustion ratio, (PCR), prereduction degree (PRO), heat transfer coefficient (HTC) , flux, scrap charge, and heat losses. Four basic cases were considered: I. 30% PRO-50% PCR; II. 90% PRO-O% PCR; III. 60% PRO-30% PCR; and IV. 0% PRO-50% PCR. Several different coals were considered and a sensitivity analysis of the critical variables was performed. The model also estimates the sulfur content of the metal. The major conclusions included:1. Post combustion significantly reduces coal consumption but above 20% PCR little reduction of FeO to Fe can be performed with the off gas.2. Prereducing to FeO (Case I) and having as much post combustion as consistent with good heat transfer is an attractive process. This process only requires a simple pre reducer, uses less coal, and is relatively insensitive to the type of coal used.3. High off gas temperatures may pose a potential problem. The off gas temperature can be reduced by using an 02-Air mixture for post combustion, limiting post combustion or adding water to the gas.4. The use of CaC03 in place of CaO or of supplemental electricity does not appear attractive.5. The melting unit is theoretically an energy efficient scrap melter. For Case I using 200 kg of scrap as part of the charge the coal consumption decreases by about 80 kg.6. With PCR > 30% the FeO content of the slag is expected to be 2-5%, and the metal will not be saturated with carbon. These factors and the increased sulfur load since coal is the fuel indicate the sulfur content of the metal may exceed 0.25%"

Jan 1, 1988

By Kimiaki Utsunomiya, Yasumasa Hattori, Yoshiaki Mori, Toyokazu Okubo

"The effect of various operating conditions on splashing behavior in a Peirce-Smith converter has been investigated with a 1/5.7 scale cold model. Dynamic similarity between the model and a commercial converter was attained by setting the modified Froude number in the model experiments in· the range for normal converter operation. It is known that for a given modified Froude number the dimensionless penetration length of gas into the liquid phase increases as the liquid density decreases. Moreover, penetration· length has a large effect on splashing behavior. Therefore, a heavy liquid, a mixture of water and lead concentrate was used as the liquid phase. It was concluded that the amount of splash dramatically decreases with a reduction in the buoyancy energy per, unit liquid mass and an increase in the horizontal distance between the tuyere tip and the edge of the mouth.IntroductionSubmerged gas injection is widely used in practice in ferrous and nonferrous pyrometallurgical operations to achieve large gas-liquid contact areas and good agitation of liquid for rapid chemical reaction. The common application in ·nonferrous industry is the Peirce-Smith converter with multi-tuyere for copper and nickel matte converting. This process has been used for over 100 years because of its effectiveness in mixing of the molten bath, as well as its merits of the engineering simplicity. However, the mechanisms which · determine the blowing performance is poorly understood, and the design and operating conditions of the Peirce-Smith converter varies widely from plant to plant, such as by diameter, length, mouth angle, tuyere position and level of molten matte. Smelters have continuously made an effort to increase converter productivity, implying maximum tuyere blowing rate. Above a certain critical blowing rate, splash of molten matte from the converter mouth becomes unacceptable because of dangerous ejection and accretion buildup around the converter mouth, which results in interference with effective hood sealing. In fact, a 1993 converter survey[!] reported that splash was a major limiting factor for blowing rate and 54% of responding plants from around the world regard it as a limiting condition[2]. In order to increase tuyere blowing rate a study of the effect of various operating conditions on splashing behavior is expected."

Jan 1, 2000

By Dong Liang, Qijie Zhai, Zhichen Zhang, Qixin Li, Zhishuai Xu

"The formation, distribution and survival of pure Al nuclei under surface pulsed magneto oscillation (SPMO) treatment were investigated with thecombination of experiments and numerical simulation. The results indicated that the nuclei originated from the whole top surface of melt owing to the oscillation of top surface induced by SPMO. The temperature field significantly affected the survival of the nuclei The electromagnetic force and flow field of the melt with SPMO treatment were simulated by finite element software ANSYS. The electromagnetic force mainly distributed below the top surface near the mould wall. The electromagnetic farce not only made the melt oscillate but also increased the convection of meh below the top surface vigorously. The oscillation near the top surface of the melt promoted the nucleation largely, and the convection increased the uniform of the temperature distribution in the whole meh which favored the survival of nucleiIntroductionAs we all know, fine equiaxed grains are beneficial fur the improvement of the mechanical property, process ability and the uniformity of metallic materials [1-2]. With the researches of recent decades, people discovered that the electromagnetic field is an efficient method to refine the solidified structure of metals [3-7]. Pulsed magnetic field technology obtains more and more attentions in recent years due to its smaller power consumption, bigger instantaneous magnetic field intensity, non-contacting with the meh and simple convenient equipment manufacturing [8-9]. However, the melts would splash fiercely when pulsed magnetic field is applied with a slightly higher power. Thus, based on the understanding of the solidification refinement mechanism of electric current pulse (ECP) [10], Gong et al [11] developed a novel technology called pulse magneto-oscillation (PMO) to refine the solidification structure. The technology can be easily applied in the solidification structure refinement of continuous casting slab. But fur aluminum continuous casting, the sump is very shallow, which greatly limits the application of pulse magneto-oscillation technology."

Jan 1, 2014

By F. E. Katrak

Rare earths markets by definition usually include not only the rare earth elements, but also yttrium. They can be subdivided into a very large light rare earth fraction (about 95 percent by weight of all rare earths consumed) consisting mainly of cerium and lanthanum and a smaller fraction (with much higher unit value) consisting of selected high-purity oxides or elements such as yttrium, europium, samarium, or neodymium. CRA estimates that the noncomnunist world market for all rare earths and yttrim was on the order of US$750 million in 1986. The main focus of this paper is on the principal uses for rare earths, some CRA-developed proprietary data on their consumption by region, and the selective nature of business opportunities in the rare earth markets. We also provide forecasts on the future trends in these markets.

Jan 1, 1989

By Ravinder N. Reddy

Electrochemical capacitors are charge storage devices. They bridge the gap between dielectric capacitors and batteries in terms of energy and power density. Electrochemical capacitors are classified into two types, electrochemical double layer capacitors (EDLCs) and capacitors based on pseudocapacitance. In EDLC, charge is stored at the interface between electrode and electrolyte. Carbon is considered to be prime electrode material for EDLCs due to its many favorable characteristics. In this study carbon materials are derived from thermal decomposition of catechol- formaldehyde polymers and are studied as electrode material for electrochemical double layer capacitors. Carbon electrode surface is characterized using NOVA 1200 gas sorption analyzer. It is also characterized using XRD and SEM. Carbon electrodewaselectrochemically characterized using cyclic voltammetry (CV). A highest capacitance of 110 F/g was observed in 30 wt% H2SO4.

Jan 1, 2006

By Alice Barreto Bevitori, Frederico Muylaert Margem, Renan Sopeletto Carreiro, Sergio Neves Monteiro, Isabela Leão Amaral da Silva

"The ramie fiber is one of the strongest lignocellulosic fibers with applications ranging from simple items such as fabrics and ropes to engineering composites for automobile parts and building panels. Characterization of the ramie fiber has recently been conducted for physical and mechanical properties. In principle, thinner ramie fiber could be comparatively stronger and consequently more effective as a composite reinforcement. In this work an attempt to correlate the ramie fiber elastic modulus obtained in tensile test with its corresponding diameter, precisely measured by means of a profile projector, was carried out. Tensile results analyzed by the Weibul1 statistic showed a significant increase in elastic modulus with decreasing the diameter of ramie fiber. Scanning electron microscopy observation of the fracture of selected ruptured fiber revealed possible mechanisms that could justify the elastic modulus/diameter inverse dependence.IntroductionEngineering applications of natural fibers obtained from cellulose-rich plants, also known as lignocellulosic fibers, are currently being the focus of attention. In fact, they are considered an enviromnental1y correct alternative to substitute synthetic fibers such as the glass fiber, associated with an intensive intake of energy during production, as reinforcement of polymer composites [1-4]. In recent years there has been a growing tendency towards the use of lignocellulosic fiber composites in several industrial sectors from civil constructions to car making. In particular, the automotive industry is expanding the number of both interior and exterior components made of natural fiber composites [5]."

Jan 1, 2012

By Freddy Syvertsen, Ali Riza Tarakcilar, Engin Tan, Derya Dispinar

"It has been shown that the disturbance of the advancing liquid front in the mould cavity may lead to surface entrained defects known as bifilms. These defects can deteriorate the mechanical properties significantly. The developments in the simulation of castings aid many casters. It is quick and economical. Therefore in this work, the aim was targeted to optimise the mould filling of a tensile test pattern design that is used for aluminium alloys. Several different designs, gatings and runner systems were investigated with Vulcan Casting Simulation Software. In addition to the achievement of non-turbulent and quiescent mould filling; other parameters such as temperature profile, porosity and feeding were investigated to optimise the process.IntroductionConsiderable effort has gone into understanding and controlling defects that are formed in aluminium and its alloys during casting. The conventional approach was the elimination of porosity by eliminating hydrogen in the melt simply due to the following reaction:"

Jan 1, 2012

By D. C. Azubike

Wolframite (FeWO4) usually having cassiterite (SnO2) as a major impurity is a primary source of tungsten. Its direct reduction/carburisation with carbon in the temperature range 1000-1400°C, and with hydrogen at 600-900°C followed by carburisation with CO at 900°C are described. Depending on the conditions and reactants employed, Fe, Fe2W, B-Sn,WC, W2C, Fe3W3C and Fe6W6C are the products. Tin was found to inhibit the overall reduction and carburisation reactions significantly. The potential for either efficient separation of iron and tungsten or a one-stage production of an iron-based metal carbide composite is discussed.

Jan 1, 1992

By B. Fresz

Before aluminum is utilized in automotive bodies, the longevity of the electrodes employed in the resistance spot welding of aluminum must increase. This paper explores the affects of electrode composition on electrode life. To compare these variables, electrode tests were completed on a Taylor Wield welding machine using, Cu-Cr, Cu- Zr, Cu-Cr-Zr, Cu-Be, and Glidcop electrodes tested to 12.5%, 25%, 50%, 100%, and 150% lifetimes. Electrode diameters were found via a magnification technique using a PULNIM video camera attached to a low magnification Wild Heerbrugg stereo-zoom microscope. From these measurements, graphs of electrode life verses face diameter and weld number verses face diameter were created. Analyses of these graphs suggest that a single failure mechanism is responsible for electrode failure, though the number of welds until failure (100% electrode life) varied with composition (700-2000 welds).

Jan 1, 1999

By Q. Chen

The magnetic properties and phase evolution of Nd-lean and/or boron-rich melt- extracted ribbons of Nd98Fe90.2xBx, where x = 6 through 11, have been studied using XRD, DTA, TMA, and VSM. The off-stoichiometric Nd2Fe14B compositions cause additional phases to be present after crystallization and affect the magnetic properties obtained. The crystallization temperature of this alloy series rises with the increasing) boron content. In addition to Nd2Fe14B and a-Fe, Fe3B is detected. It is found that increasing the boron content reduces B, within this composition range. The magnetic properties are directly associated with the relative magnetic phase content in the samples.

Jan 1, 1997

By Lee Fergusson

"The primary features of ViroMine™ Technology are introduced and applications of ViroMine™ Technology to mine site remediation and the treatment of a variety of intractable waste-streams, including a technical discussion of acid neutralizing capacity, metals binding capacity and longterm stability of results. Outcomes from four applications at high-profile international mine sites are presented: 1) the superfund site at the Gilt Edge Mine, South Dakota, USA (four years of data on the treatment of acidity, TDS and metals such as Al, Co, Fe, Mn and Zn); 2) one of Australia’s most polluted sites at King River Delta in Tasmania (treatment of TAA and TPA, and metal and metalloid contaminants such as As, Cr and Hg); 3) The Aljustrel “Aqua Forte” mine site in Portugal (high acidity, metal and metalloid contaminants such as Al, As, Cu and Zn) and 4) the Ulsan Iron Ore Mine at Ulsan, South Korea (treatment of metal and metalloid contaminants such as As, Cd and Ni).IntroductionThe commercialisation of ViroMine™ Technology has resolved some of the most intractable pollution issues associated with historic mining ventures on a global scale and has facilitated the neutralisation of Acid Rock Drainage (ARD), remediation of acidic and metal contaminated impoundments (including tailings dams) and promoted revegetation on tailings deposits and waste rock dumps. ViroMine™ Technology also enables current mining ventures to manage effluent simply and efficiently to meet increasingly stringent environmental standards and is enabling the mining sector to reconceptualise the management of mine spoil. The abilities of ViroMine™ reagents to neutralise the actual and potential acidity of sulphidic mine spoil coupled with the ability to bind metal and metalloid contaminants into non-bio-available forms are the key features delivering environmental and economic benefits to the mining sector and the broader community. Results from four projects utilising ViroMine™ Technology are presented to highlight the suitability of ViroMine™ Technology to treat all forms sulphidic mining wastes. 37"

Jan 1, 2008

By Thomas A. Post

The methodology of determining the optimum SX pumper-mixer system based on bench top, pilot, or small-scale solvent extraction systems, is demonstrated. The design of small-scale SX-plants is different than a full-scale plant. The difference is explained here. The use of dimensionless parameters Nh, Nq, and Np that describe the head, flow and power of the pumper is shown and how to use them for the scale-up. Additional data is required to determine the optimum operating range. Applications of this methodology were used to design well known currently operating SX plants. The emphasis on the optimization of hydraulic efficiency will be shown on examples, including how the hydraulic efficiency is affected when the throughput of the system goes beyond the design. Designs of all sizes of equipment will be shown which optimize the hydraulic efficiency.

Jan 1, 2003

By Shunli Zhang

Metals recovery from electronic scrap by physical separation may provide an alternative to the current recycling approach, through which halogenated flame retardants can result in hazardous dibenzo-p-dioxins and dibenzo-furans. On the basis of a complete sink-float analysis of personal computer and printed circuit board scrap, and in view of the advantages of dry processes for electronic scrap recycling by mechanical separation, air table separation is prioritized in an attempt to separate metals from plastics and glass involved. In the present paper, theoretical and practical considerations of air table separation have been detailed. It has been shown that air table separation is effective for recovering copper and precious metals from this specific waste stream. With the feed rate of 60 kg per hour, the combined grade and recovery of copper, gold, and silver attainable for the two heavy products produced by the air table used in the present study was shown in the following table:

Jan 1, 1998

By Giuseppe Granata

An innovative process using titanium tetrachloride (TiCl4) gas as reactant has shown successfully to obtain titanium through electro-winning of TiCl2 formed in-situ on titanium cathode. The process involves a continuous feed of TiCl4 gas reacting onto a titanium cathode immersed in a molten salt (NaCl-KCl), whereby in-situ formation of titanium dichloride (TiCl2) through a disproportion reaction. Simultaneously, the TiCl2, thus in-situ formed in the molten salt media, has been reacted into chlorine gas and titanium, the latest electrodeposited on the titanium cathode by electrowinning. The reaction kinetic of this innovative process was investigated in terms of TiCl2 in-situ formation rate and galvanostatic electrodeposition rate, where, in particular, the effect of operating variables such as TiCl4 partial pressure and flow rate, as well as temperature and galvanic potential applied was investigated.

Jan 1, 2014

By Mark Jolly, Nasim Soleimanian

"During the last 20 years CFD (Computational Fluid Dynamics) has been used as a tool to aid furnace designers and manufacturers to improve energy efficiency and effectiveness of glass furnaces. However as the models are maturing the effect of feeding equipment used to push the raw material into the furnace has not been included in the process models. This paper investigates the effects of batch pattern in the melt space caused by charging equipment on the energy efficiency of the furnace focusing on the melting zone. A simple batch patterns sensitivity study has been performed using purpose built software (Glass Furnace Model-GFM). It is concluded that in order to further reduce the energy consumption of the furnace it is necessary to model the batch charging process in more detail to find more opportunities for improvement.Introduction Glass manufacturing is a conservative industry which applies to all the four major segments (float glass, container glass, fiberglass, and specialty glasses). Risks due to the high capital investment, very long service life of the furnaces, and the demand for high performance and quality from the outset translates into evolutionary progress rather than revolutionary. The main problem facing glass manufacturers are the financial cost of manufacture, its impact on the environment, and mounting pressure imposed by the authorities for greener manufacturing and reduction in emissions.The main energy intensive activities involved in continuous glass manufacturing are: the need for high temperature to create and maintain the viscous flow, homogenisation of glass melt (melt residence time), and maintaining the two to achieve continuous output of glass at the right quality. The high temperature and long duration of homogenisation has resulted in the design oflarge furnaces, which have high energy consumption, low specific performance, and high C02 emissions. As an example in the container glass sector the most efficient furnace has a specific primary energy consumption of 3.8 GJ /tonne of glass at a level of 50% cullet in the batch. Even very small improvements in efficiency by optimising operation would have a high impact [1-14]. Given the conservative nature of the industry and the costs involved in experimental data gathering, CFD modeling of the process has been used extensively during last two decades to not only improve our understanding of the process but also as a tool in predicting possible optimisation windows, e.g. Glass Furnace Model ( GFM), a commercially available piece of software that has been developed to optimise furnace operation."

Jan 1, 2013

By Wang Chen

COREX process is briefly introduced. A static model combining a set of mass and heat balance equations has been developed. Taking the specified inputs from the graphical user interfaces, the model is capable of calculating the consumption of raw materials and fluxes, the volume and composition of the slag and the volume and composition of the generator gas. The model enables the examination of the changes of materials and energy flows induced by the variations of operational parameters and raw materials chemical analysis. The model allows a detailed process analysis and adjustment of the plant operation and can thus be used to improve plant operation.

Jan 1, 2008

By Tsunehisa Nishimura

Stable operation of the blast furnace needs adequate control of the lower part. To clarify the behavior of the lower part of the blast furnace with accurate consideration of the property of slag and its flow characteristic, a new mathematical model has been developed. Using this model, the effects of the change of operational conditions on the behavior of the lower part of the blast furnace were studied. Further, means to control of the lower part of the blast furnace, especially effective means to maintain adequate temperature, were discussed. And desirable slag property and composition, especially the method to control FeO concentration dripping from the bottom of the cohesive zone to avoid a decrease in temperature of the lower part of the blast furnace was estimated.

Jan 1, 2006

By Gordon A. Irons, Diancai Guo

"Uneven movement of scrap during melting in an Electric Arc Furnace causes operation problems: cave-ins interrupt electric power input. The movement also influences the radiation heat loss to water-cooled side panels and roof. An apparatus has been built to simulate the flow of scrap that may be interlocked. It has been observed that flow starts at the point where the suspended length of the pile bottom reaches the average scrap size, and proceeds in the form of cave-ins, but scrap pieces slide with each other as ordinary granules. After a cave-in, the pile angle usually remains much larger than the normally observed angle of repose. The force balance of a partially suspended scrap pile has been analyzed, and the equivalent cohesion due to interlocking estimated. A numerical model has been developed to simulate the scrap flow. Simulated results agree reasonably with observed phenomena.IntroductionWhen one considers the melting of steel scrap in an electric arc furnace (EAF), it is helpful to understand the movement of the material during meltdown. As industrial experience demonstrates, scrap movement greatly affects EAF operation. In a typical operation, scrap is dropped into the furnace from scrap buckets. The roof and electrodes are swung into position, and power is applied to the electrodes situated over the scrap. The electrodes ""bore"" into the scrap by melting into the steel in the immediate vicinity of the electrodes as they are lowered. If solid scrap pieces gradually slide towards the arc area, the electric power supply can be maintained at a high level, with few interruptions or drastic electrode adjustments. This results in a high production rate and low power consumption per tonne of steel produced. On the other hand, if the charge moves down unevenly, i.e. in large surges, usually called cave-ins, the electrodes must be drastically raised, and power supply frequently interrupted. This is also accompanied by a high level of harmonics induced in the power network, deteriorating the quality of electricity supplied to other users.In addition, the movement of scrap in an EAF also influences the furnace heat efficiency, as the scrap pile is much closer to the electric arcs compared to the furnace wall and roof, and absorbs more radiated heat. Early exposure of the wall and roof to the arcs will increase the heat loss due to radiation, and reduce the service life of the furnace."

Jan 1, 2004

By Susumu Okabe

Injection metallurgy is widely adopted in various fields of metallurgical operations to achieve high productivity. The Mitsubishi Continuous Copper Smelting and Converting Process employs the top blown lance technique for the continuous supply of solid charges and reaction gases into the molten bath, where the agitated bath contributes to enhance the heat and mass transfer and the increased gas/liquid interface area accelerates the reaction. However, excessive splashing of the molten materials accompanied by the injection may cause an unexpected wear of the furnace lining. In order to estimate the splashing rate quantitatively, and to optimize the furnace design and the blowing condition, a physical model study of the top blown gas injection onto the liquid bath was carried out. An equation of the splashing rate was obtained as the function of cavity size, gas velocity and bath properties.

Jan 1, 1995

By lchiro Aoi, Hideo Nakae, Makoto Yoshida, Makoto Ishino

"The influence 6f gravity on the microstructure of unidirectionally solidified Cu-Pb monotectic, Ag-Si and Fe-C eutectic alloys is studied. In order to examine the influence of gravity in a lg environment, both the upward (opposite to direction of gravity) and downward (direction of gravity) unidirectional solidifications are carried out. The results are as follows: (1) For the upward solidified Ag-Si eutectic alloy, the eutectic Si continuously grows. On the other hand, in the downward solidified Ag-Si alloy, the Si grows discontinuously and disperses into the ex-Ag matrix. (2) No morphological difference in the eutectic growth is observed between the upward and downward solidified Fe-C eutectic alloys. (3) In the case of the upward solidified Cu-Pb monotectic alloy, a banded structure, which consists of Pb-rich layers and Cu-rich layers, is observed. However, such a banded structure -is not observed in the downward specimen. (4) The banded structure is not found in the upward solidified Cu-Pb-0.05 mass % Al and Cu-Pb-0.1 mass % Al alloys. In the Cu-Pb-0.05 mass% Al alloy, a fibrous -L 2 phase grows continuously parallel to the growth direction at low growth rate. Only 500 mass ppm addition of aluminum induces the morphological change of the monotectic L2 phase.IntroductionThe influence of gravity on the solidification of eutectic and monotectic alloys has been investigated in microgravity environments [l-9]. The purpose of these studies was to obtain a homogeneous microstructure of eutectic or monotectic alloys, most of which alloys tend to solidify with macro-segregation under gravity. However, in most of the previous experiments, e.g., in free fall systems, in aircraft or in space laboratories, the growth rate was too high to realize a planar solid/liquid interface. This would be due to the limited time for solidification. Thus, it was difficult to examine the influence of gravity on the planar coupled growth of the eutectic or monotectic alloy. In this study, both the downward U.D.S. (unidirectional solidification by gravity) and upward U.D.S. (opposite direction to gravity) are carried out in order to examine the influence of gravity on the coupled growth in a lg environment [l0, 11]. In the case of the downward U.D.S. using the current Bridgman method, the molten alloy must be confined between the crucible and the solid."

Jan 1, 2000