Search Documents

By He De-wen

The influence of coal desulphurization by fungus was experimentally studied. The present results suggest that fungus can effectively remove inorganic and organic sulfur in coal. The main factors that influence the desulphurization by fungus such as pH value, temperature, coal slurry concentration and coal granularity are studied by orthodox experiment and the optimal experimental conditions are as follows: pH value 6, temperature 45 C, coal slurry concentration 10% and coal granularity 100 m. Under the above conditions, fungus can remove up to 44.96 total sulfur and 54.87 inorganic sulfur within two days and their desulphurization rates will increase along with time. Compared to sulfolobas, desulphurization by fungus is steady and more effective and has the advantage of high speed.

Jan 1, 2006

By P. G. McCormick

The refining of rare earth metals by the direct solid state reduction of their respective chlorides during mechanical alloying has been studied. Erbium and gadolinium were synthesised by milling their respective chlorides with calcium. The mechanical alloying of SmC13 with calcium resulted in partial reduction of SmC12. Examination of the milled powders using X- ray diffraction and analytical electron microscopy has enabled characterisation of product structure and morphology. The synthesis of Fe17Nd2 by the mechanical alloying of NdC13 and Fe with calcium has also been studied. The Fe17Nd2 phase forms during heat treatment of the mechanically alloyed powder.

Jan 1, 1992

By K. P. Nishad

The origin of many casting defects can be traced at the mold filling stage. Entrapped air/gas pockets and oxide film formation are notable examples. In the present work, the mold-filling process is simulated using a mathematical model, built on a multi-physics based commercial package PHYSICA. The simulation code has the capability to solve multi-phase problems. The numerical model addresses a complicated dynamics of filling operation including free surface flow and subsequent flow behavior and is based on conservation of mass and momentum. The Free surface is modeled using the scalar equation method (SEM). The model is validated with benchmark experimental results from the literature. The role of turbulence and the pouring rate on variables affecting sites prone to oxide film formation are investigated using a simple but novel technique. Key findings of the work are presented.

Jan 1, 2006

By Peter Willbrandt

Norddeutsche Affinerie's routes date back to the 18th century. NA was established in 1866 as a joint stock corporation. NA's core business covers the production of copper cathodes from primary and secondary raw materials and the processing of them into wire rod and shapes. Part of the shapes are processed into pre-rolled strip and shaped wires within the Group. With some 3,200 well qualified and highly motivated employees, the NA Group produces some 560,000 tonnes of copper cathodes, 370,000 tonnes of wire rod, 230,000 tonnes of shapes, 130,000 tonnes of pre-rolled strip as well as 70,00 tonnes of strips and shaped wires annually. NA's product range is complemented primarily by precious metals, selenium, sulphuric acid, lead and nickel sulphate. The paper will give an insight into the performance of NA and its business units with regard to production, environmental and health protection and occupational safety.

Jan 1, 2006

By Cevat Serdar Kucukkaragoz

The kinetics of prereduction of Chromite by carbon was studied under argon atmosphere at temperatures between 1000°C and 1300°C . The compacted and agglomerated specimens were reacted by using a TGA system. The mixing characteristics and the degree of compaction of the chromite and coke particles were the main parameters influencing the reduction kinetics. The reduction rate increased with temperature reaching to 81% reduction at 1300°C. The metallization started as the metallic nucleation around the particles which was first observed at 1100°C. The particles were surrounded by the metallic phase at approximately 40 % reduction obtained at 1200°C. At 1300°C, the reduction proceeded with a high rate during initial stages and with a low rate at final stages. The reduction was found to proceed in the sequence of Fe3+to Fe2+, Fe2+ to Fe(metal) and Cr3+to Cr(metal) with the formation of carbides.

Jan 1, 2006

By Tateo Usui

In the course of carbonization of coal under a rising temperature condition, volatile matter (V.M.) is released. The kind and amount of V.M. released depend on the kind of coal. Components of V.M. are tar, hydrocarbons (CH4, C2H4, C2H6, C3H8), CO, CO2 and H2, which are released in this order as a function of carbonization temperature. When the carbonization of coal under a rising temperature condition is interrupted at a certain temperature, TC, max, semi-coal-char with residual V.M. is obtained. If some optimum interruption-temperature is chosen, small but most suitable amount of V.M., namely H2, is retained. When the semi-coal-char thus obtained is heated again under the same rising temperature conditions but up to more than TC, max (1), the residual V.M. is released from just around TC, max (1). We propose novel iron ore agglomerate bearing such semi-coal-char with some strength. While simple iron ore agglomerate bearing coal char will start the reduction reaction as solid-solid reaction at somewhat higher temperature, the proposed one will start the reduction reaction as gas-solid reaction at somewhat lower temperature but a little higher than TC, max. Samples of semi-coal-char and novel iron ore agglomerate bearing such semi-coal-char have been prepared and evaluated.

Jan 1, 2006

By Brian Lightfoot

Ausmelt Technology uses a furnace/slag/lance system in a way analogous to the way a chemical engineer would use a mixed reactor. The technology is sufficiently versatile to treat materials under a very wide range of temperature and chemical conditions. At one extreme the system has been operated at temperatures high enough and oxygen potentials low enough to make iron. At the other extreme it has been operated of temperatures as low as 800°C and oxygen potentials high enough to cupel lead from silver. This versatility permits the treatment of a great variety of wastes including asbestos, mixed organic\heavy metal wastes, incinerator ash smelter residues, waste water treatment sludges, organochlorine compounds and many others.

Jan 1, 1994

By M. L. Free

Electrowinning is directly impacted by many parameters that include electrolyte composition, voltage, current density, contact resistance, temperature, electrode spacing, and fluid flow as well as many other interrelated factors. The effects of these parameters are primarily related to thermodynamics, mass transport, and electrochemical kinetics. In this study thermodynamic, mass transport, and electrochemical kinetic equations are simultaneously solved to determine the effects of such parameters on electrowinning current efficiency, power consumption, electrodeposit morphology, and electrodeposit distribution. Modeling predictions will be compared with experimental results.

Jan 1, 2006

By Ioannis Paspaliaris, Dimitrios I. Gerogiorgis, Dimitrios Panias

"Red mud fiberization is a process with remarkable potential, alleviating environmental pressure by transforming an aluminum by-product into mineral wool, thus to various marketable products. A promising mineral wool process is molten slag fiberization via an impinging air jet, which avoids mechanical wear and rotating parts. The molten slag which remains after pig iron casting flows out of a heated ladle orifice at a high temperature (1600 °C) and adjustable flowrate, and forms a free-falling vertical jet which visibly radiates its excessive heat: at a given distance, a high-velocity impinging air jet meets the vertical melt jet perpendicularly (or at an angle), inducing intensive droplet generation, subsequent fiber elongation, collection and processing.This paper focuses on high-fidelity CFD modeling of the molten jet flow under external cooling: the model encompasses all physicochemical phenomena (melt laminar flow, radiative cooling) and considers several temperature-dependent slag transport properties in order to understand which operational degrees of freedom (manipulated variables) are useful to process optimization."

Jan 1, 2012

By John Sakala, Jeyapandian Sasikumar, Sydney Kwalela

The Isasmelt Furnace was commissioned in September 2006 with a concentrates treatment capacity of 850,000 tonnes per annum. However, the converter section became a bottleneck to the high throughput. Over 25% of the Isasmelt Furnace down time was attributed to lack of converter space. Factors that affected converter operations were low tuyere line campaign life (an average of 150 blows), high reverts generation, low conversion rates, and high converter cycle time. As a result of efforts carried out to improve converter operation, the average campaign life has increased to over 250 blows and reverts generation has been reduced from 22% of concentrate treated to 15%. Blister copper conversion rate has increased from 15 tonnes per hour to 19 tonnes per hour and blowing time per cycle has been reduced from 5.7 hours to 4.7 hours.

Jan 1, 2012

By J. E. Dutrizac

Mineralogical studies were carried out on nodulated copper cathodes from three primary refineries to characterize the nodular growths and to elucidate the causes of the nodulation. Nodulation is often initiated at the surface of the starter sheet or the stainless steel plating blank, although a layer of smooth copper sometimes is deposited before nodulation commences. In some instances, the "roots" of the nodules exhibit a pronounced dendritic texture that is associated with an abundance of cavities. Slimes particles are not usually associated with these growth features which lead to a globular surface deposit. The globules sometimes develop into larger nodules, and this type of nodulation is likely caused by improper addition agent concentrations. The nodules on most cathodes, however, exhibit "roots" at the contact with the substrate that are associated with microcavities and large clusters (>40 µm) of slimes particles. The slimes constituents are commonly Ag powder, PbSO4 and Cu2(Se,Te) but not AgCu(Se,Te) or Ag,(Se,Te). The size of the slimes clusters, rather than their composition, appears to be the important factor causing the copper to grow into nodules. Tiny individual slimes particles themselves do not appear to cause cathode nodulation.

Jan 1, 1999

By John L. Uhrie

Oxide stockpile leaching operations can realize increased copper recovery and decreased acid consumption from in-situ generated acid resulting from the oxidation of intentionally introduced pyrite recovered from mill tailings or other sources. While all oxide leach ores can benefit from pyrite addition, low acid consuming ores can show remarkably increased recovery and net acid generation; however, more highly acid consuming ores will show benefit more exclusively through increased copper recovery. Additional work shows that the value of highly acid consuming ores can be optimized by balancing copper recovery against acid consumption.

Jan 1, 1999

By Chuan-fu Zhang

In present work, the physical properties of molten FenO-MgO-CaO-SiO2 slags were measured .It is shown by the results that when the slag composition is as follow: MgO 8%~12%, CaO 2%~8%, Fe/SiO2 1.2~1.6, the viscosity of the slags decreases with the increase of temperature. When the Fe/SiO2ratio and the MgO content are fixed, the electrical conductivity increases and the viscosity decreases as CaO content increasing, while the content of CaO exceeds 6% its influence weakens. When the MgO content is 11% and the CaO is 6%, the viscosity of the slag decreases markedly as the increase of Fe/SiO2 ratio. Its influence to viscosity is inconspicuous when the Fe/SiO2 ratio exceeds 1.5. When the CaO content is 6% and Fe/SiO2 is 1.2, the electrical conductivity decreases with the increase of MgO content as temperature is below 1290, but increases when temperature is above 1290. When the MgO content is 11% and the Fe/SiO2 ratio is 1.2, the electrical conductivity increases with the increase of CaO content. When the CaO content is 6% and MgO content is 11%, the electrical conductivity increases as the increase of Fe/SiO2 ratio, while its influence weakens as the temperature increases continuously. The electrical conductivity rises when temperature increases at any slag content. The melting temperatures of FenO-MgO-CaO-SiO2 semi- synthesis slags from this work were below 1290.

Jan 1, 2006

By Jitka Jandová

A laboratory process based on simple and environmental friendly operation, aimed at recycling of spent Li/MnO2 batteries, is described in this study. This process involves roasting Li/MnO2 batteries in a vacuum furnace at 650°C, followed by selective leaching Li2CO3 from calcined electrode material in distilled water at ambient temperature and controlled crystallization of pure Li2CO3.

Jan 1, 2006

By Mark F. Vancas

Virtually every new process plant project goes through the ?Feasibility Study? phase before actually being built. The Feasibility Study is used by the owners and the bankers to evaluate the economics of the project and determine whether or not the proposed investment meets their respective investment guidelines. With a positive result, the project is approved and goes to construction and operation. Then, the actual costs are incurred and these actual costs may or may not agree with what the Feasibility Study predicted. Just how good have Feasibility Studies been? This paper looks at various projects and compares predicted to actual results and also gives information on how to spot a poor feasibility study.

Jan 1, 2003

By O. C. Rojas

Improvements and modifications on lay out and process, from 1997 till 1998, are presented. Based on a Teniente Converter, started up 1993, a Strategic Development Plan was structured to increase the production efficiency and comply with the enviromental regulations, too. It considered the oxygen supplies to the Teniente Converter and Peirce Smith converters; reverberatory furnace shut down as a smelting unit; and the Teniente converter slag treatment through a combined process between a Slag Settler furnace and flotation. Also it included the off-gas handling and treatment.

Jan 1, 1999

By W. F. Miao

Nanocrystalline mixtures of Nd2Fe14B and a-Fe have been synthesized by mechanical milling and heat treatment. The samples exhibit isotropic behavior, with significant remanence enhancement associated with exchange coupling across the interfaces of hard and soft magnetic phases. Measurements of the effect of heat treatment on structure and magnetic behavior demonstrate the important influence of grain size on magnetic properties. The effect of alloy additions to increase the saturation magnetization of the soft phase and the magnetocrystalline anisotropy of the hard phase has also been investigated.

Jan 1, 1997

By Patrick R. Taylor

A kinetic study of the fluosilicic acid leaching of galena was performed under the presence of different oxidants. Fluosilicic acid concentration, agitation speed, concentration of solids and particle size, type and concentration of oxidant, and temperature were the variables studied. Hydrogen peroxide was found to be the most effective oxidant, its effectiveness being proportional to its concentration. As expected, an increase of leaching temperature increased the overall extraction and extraction rate. The same was found by decreasing the galena particle size. It is thought that leaching using hydrogen peroxide is controlled by fluid film mass transfer due to the calculated apparent activation energy. Reaction by-products such as sulfur and sulfur compounds retard the leaching rate. A mathematical model is proposed and compared to experimental results.

Jan 1, 2003

By Basak Anameric

Pig iron nugget process was developed by Kobe Steel as an environmentally friendlier, economical alternative to traditional blast furnace process. The process aimed to produce highly metallized, slag free pig iron nuggets throughout a single stage heat treatment, utilizing coal as a reducing ? carburizing agent. The objective of this work was to determine whether the pig iron nuggets produced at the laboratory conditions had comparable physical and chemical properties with the blast furnace pig iron. The physical and chemical properties of the pig iron nuggets were determined utilizing x-ray fluorescence spectroscopy, x-ray diffraction, optical microscopy, scanning electron microscopy, energy dispersive spectroscopy and apparent density measurements. The pig iron nuggets had similar chemical composition and apparent density values (6.7 ? 7 g/cm3) with blast furnace pig iron and they had microstructures similar to low carbon white cast iron. These properties make them a competitive alternative to blast furnace pig iron.

Jan 1, 2006

By R. Peterson, D. C. Popko, J. Y. Hwang, R. McChesney, A. M. Hein, R. C. Greenlund, M. Jeong

MTU is conducting a study to recycle and reuse the aluminum waste generated from various segments of the aluminum smelting industry. This research is supported by the U.S. Department of Energy and industry. A portion of this effort is to determine the operating efficiencies of Eddy Current Separation, comparing separating characteristics of white and black dross. The results of this effort will be presented here.

Jan 1, 2000