Search Documents

By Jin-yan TIE, Ke-xin JIAO, Qian Li, Hai-bin ZUO, Jian-Liang Zhang, Meng SHEN

This paper designs three factors such as temperature, pH, conductivity and three levels of orthogonal test. Temperature is a significant factor. However PH and conductivity are not significant through poor analysis. Further research is conducted on the temperature. Temperature stability is 50 . Suitable water velocity is 2.3m/s, which is calculated based on the largest part of the heat flux intensity and the corresponding water temperature should be controlled with 1.5. Meanwhile, water velocity increased has little effect on the heat transfer capabilities.

Jan 1, 2015

By Dale W. Collins

The disposal of arsenic from copper operations possess various health, environmental and processing problems. There are basically two areas of concern. The first being the disposal or treatment of smelter flue dusts and the second the removal of arsenic from refinery electrolytes. A number of treatment options have been proposed including the addition of soluble arsenic wastes to copper heap and dump leaching solutions. This approach will allow arsenic to be reintroduced to the ore via Solvent Extraction (SX) raffinate associated with hydrometallurgical operations. Knowledge of the attenuation behavior and mechanism during leaching is important in determining the long term stability of arsenic and the success of this approach. Parameters, such as uptake capacity, pH, particle size and solution chemistry have been investigated. Arsenic attenuation has been examined using column leaching with experiments employing both continuous flow and pulsed additions of As(V). In the initial stages of leaching, the attenuation of arsenic appears to depend on the pH and iron concentration in the effluent. Arsenic stability in the copper oxide ore has been examined with rinses of progressively lower pH.

Jan 1, 1994

By David J. Howard, Christine Broadbridge, David C. Paine

"High pressure vapor/solid reactions offer an opportunity for novel synthesis and processing of thin film materials and structures for electronic, optical, and magnetic applications. In this paper we review the use of two high pressure techniques that operate from 25 to 1000 atm (2.5 to 100 MPa) to fabricate thin film oxide structures from Si1-xGex deposited on Si wafers. High pressure synthesis enables temperature-independent control of reaction rates in the oxidation of this multicomponent semiconductor system and hence offers the opportunity to form thennodynamically metastable Si1-xGex<h from the alloy. The thermodynamics of the Si-Ge-0 system are reviewed and a method is described that utilizes selective chemical reduction (via H2 gas) of Si1-xGcx<h to form Ge precipitates in an SiO2 matrix. IntroductionAlloys of Si1-xGex grown epitaxially on Si substrates by chemical vapor deposition (CYD) and molecular beam epitaxy (MBE) have been used to create high performance microelectronic devices1. These devices show improved performance over conventional Si technology because they exploit the Si/Si 1-xGex band-gap discontinuity and take advantage of higher hole mobilities in the Ge containing alloys. While a range of devices based on heteroepitaxial systems have been demonstrated, the Si1_xGex alloys are of particular interest because they are most closely compatable with standard Si device processing. One disadvantage of Si-based materials systems is that they are not typically useful emitters of light. This is important since the use of light (rather than electrons) for transmitting and processing signals into, out of, and within Si-based microelectronics would represent a major technological advance in microelectronics-based communication and computer technologies. Nevertheless, through the use of innovative processing techniques it may be possible to use the Si1_xGex/Si heteroepitaxial system in integrated microelectronic/light-wave technologies."

Jan 1, 1994

By Ari I. Kogut

Impurity minerals in fluorspar ores and concentrates from a deposit in Southern Africa have been studied by reflected light, transmitted light, and cathodoluminescence microscopy. The principal impurities are quartz, calcite, aegirine, apatite, ankerite, magnetite, goethite, and synchysite [Ca(La,Ce,Nd)(C03l2Fj. Cathodoluminescence microscopy was found to be very useful in studying the character of the fluorite and especially for recognizing the presence of apatite and calcite impurities. Fluorite exhibits blue, calcite shows yellow, and apatite has white, light purple, and pink cathodoluminescence. The cathodoluminescent character of apatite varies with its geological environment and position in the orebody. The results of this microscopic study show that phosphorus present in flUorite concentrates occurs principally in binary locked apatite-fluorite particles. Successive fluorite cleaner concentrates contain progressively smaller amounts of locked apatite-fluorite particles. Free apatite has been effectively partitioned to the final tailings.

Jan 1, 1995

By Denise Crocce Romano Espinosa

The recycling of waste of electric and electronic equipment (WEEE) is one of the main modern challenges. Among the variety of WEEE, batteries can be set apart due to their composition and their growing demand along with portable devices. The objective of this work is to characterize the thermal behavior of a sample of mixed types of batteries using a thermobalance (TGA). The results of tests showed that Cd evaporated up to 800ºC, Zn evaporation occurred mainly above 900ºC and manganese oxides were pre-reduced to MnO at temperatures above 900ºC.

Jan 1, 2009

By V. Blet

Rare earth elements (REE) are regarded today as highly critical raw materials but currently lack suitable recycling processes. A combined hydro- and pyrometallurgical process aimed at REE recovery from used NdFeB permanent magnets was recently developed by the CEA. The process integrates the physico-chemical treatment of magnets, followed by a solvent extraction step for the recovery and intra-REE separation using a selective extractant. A subsequent pyrometallurgical treatment via molten chloride salt electrolysis allowed the isolation of pure Dy metal. Technical-economic assessment and life-cycle analysis were also conducted. Following this first successful demonstration, a new project aimed at the recovery of REE from end-of-life nickel-metal-hydride batteries is currently being developed in association with industrial and academic partners. The project aims at evaluating from an experimental and economic perspective different processes converging at the production of value-added products such as cermet materials for catalytic applications, purified REO concentrates, or metallic alloys.

By Wei Yu, Tiejun Chun, Jian Pan, Deqing Zhu

In this paper, the technology of producing fluxed pellets by using hydrated lime as binder instead of bentonite was carried out. Green balls with 0.8% bentonite and others with 2% hydrated lime were obtained under the same conditions of 1.5% coke, 1.45 basicity and balling at 8.5% moisture for 13 min in disc pelletizer. The properties of two types green balls were as follows: drop numbers of 4.8 to 5.0 times/0.5m, compressive strength of 19.7 to 24.2 N/pellet and thermal shock temperature of 280 to 385?, respectively. Comparing with bentonite as binder, the compressive strength of fired pellets with hydrated lime is elevated by 13.8% and climbs up to 3113 N/pellet under the following conditions: preheating at 1050? for 10 min and firing at 1300? for 15 min. The hydrated lime also improves the metallurgical performance of fired pellets. The reduction index was enhanced from 68.6% to 70.6%, RDI+3.15 increased from 90.1% to 98.8% and reduction swelling index dropped from 22.4% to 7.4%, respectively. Therefore, hydrated lime can not only replace bentonite as binder to enhance the firing behaviors of green balls, but also effectively improve the metallurgical performance of fluxed pellets which can be used as high quality feed for blast furnace.

Jan 1, 2011

By Donna Guillen, Matthew Lehar, Sebastian Freund, Jennifer Jackson, Helge Klockow

"Research and development is currently underway to design an Organic Rankine Cycle (ORC) system with the evaporator placed directly in the hot exhaust stream produced by a gas turbine (GT). ORCs can be used to generate electricity from heat that would otherwise be wasted, thus producing carbon-free energy. In conventional ORC configurations, an intermediate oil loop is used to separate the hot gas from the flammable working fluid. The goal of this research effort is to improve cycle efficiency and cost by eliminating the pumps, heat exchangers and all other added cost and complexity of the additional heat transfer loop by developing an evaporator that resides in the waste heat stream. Direct evaporation – although simpler and less expensive to implement than indirect evaporation of the working fluid – has historically been avoided due to a number of technical challenges imposed by the limitations of the working fluid. The high temperature of the hot exhaust gas may cause decomposition of the organic working fluid and safety is a major concern due to the high flammability of some of these working fluids. The research team has addressed these challenges and developed a new direct evaporator design that can reduce the ORC system cost by up to 15%, enabling the rapid adoption of ORCs for waste heat recovery. The ORC system is intended to integrate with the GT either as a retrofit or to be marketed as a single package, thus maintaining the manufacturer’s warranty.IntroductionWaste heat from turbines and engines used in industrial applications along with waste heat from industrial processes are exceptionally abundant sources of energy. If even a fraction of this waste heat could be economically converted to useful electricity, it would have a tangible and very positive impact on the economic health, energy consumption, and carbon emissions in the U.S. manufacturing sector. Land-based gas turbines are used in a broad range of applications to produce both shaft and electrical power. Most commonly known for generating electricity either as peaking units or as base load units, they are also used to directly drive pumps, compressors or other machinery requiring shaft power. Simple cycle gas turbines have the advantage of a short startup time relative to coal-fired and nuclear units, however, they incur a significant penalty on their efficiency. Large frame gas turbines usually are combined with bottoming steam-based Rankine cycles to increase the overall efficiency of the system and thereby improve their cost performance. Small-frame gas turbines with exhaust temperatures around 500°C could in principle benefit from steam bottoming cycles, but rarely use them in practice because of the high capital cost of the steam system. Particularly for base load small frame gas turbines, akin to those used in pipeline applications, an increase in efficiency is highly desirable."

Jan 1, 2011

By Mary Cunningham

The EPA and DOE have collaborated on a series of studies to evaluate the effectiveness of treatment technologies at stabilizing bulk elemental mercury and wastes containing high concentrations (i.e., with greater than 260 mglkg total mercury) and multiple forms of mercury. The data from these treatment demonstrations are intended to help EPA to determine if regulatory revisions to allow a stabilization alternative for high-mercury subcategory wastes are warranted. In addition to mercury-contaminated wastes, the disposal of bulk elemental mercury is of concern because of the excess quantity of mercury in the Defense Logistics Agency (DLA) stockpile, as well as other potential sources of excess elemental mercury. The studies evaluated the effectiveness of several technologies at: I) stabilization of mercury in a "hard-to-treat" matrix; and 2) conversion of elemental mercury into a stable waste form for disposal. A surrogate waste was designed for the study on high-mercury wastes, which included an organic form of mercury, elemental mercury, and several mercury salts in an inorganic matrix. The surrogate waste and the bulk elemental mercury were treated by the vendors, and the treated waste forms evaluated for mercury Icachability, using both the TCLP and an automated, constant-pH leaching protocol. Constant pH leaching was conducted at pH 2,4,6,8 10 and 12 for 14 days at each pH. The leaching data demonstrate that the stability of the mercury in three treated waste forms varies widely across the pH range tested. Clearly, the stability of mercury in these treated waste forms will be highly dependant on the disposal conditions. The combination of site-specific disposal conditions and appropriate treatment technology must be considered as decisions are made about disposal of high-mercury wastes.

Jan 1, 2003

By D. E. Roberts

Over 425 million used automotive oil filters are discarded in the United States each year. Estimates prior to this research claim that 10% are recycled with the remainder typically being landfillcd. Surveys conducted with ferrous scrap users and oil filter processors as part of this research reveal that at least 15% are currently being recycled as ferrous scrap. Oil filter scrap is not being used by many operations because of concerns with scrap consistency and quality. These concerns stem from trials conducted in the infancy of the oil filter recycling movement. Consistent scrap quality depends both on the content of the used oil filters and the processing technique used to produce the scrap. Technology has advanced since the first recycling trials were conducted by steelmakers. Several different types of scrap are available, including pucks, bricks, cubes, and shred. This research conducted at the University of Missouri-Rolla investigated the content of used oil filters and compares the recyclability of different oil filter sizes and designs. Filters vary by application and vary between manufacturers for a particular application. An understanding of the scrap itself as well as the concerns and problems of both oil filter recyclers and oil filter processors is necessary to increase the number of used oil filters being recycled.

Jan 1, 1996

By I. A. H. Schneiderl

Eichhornia crassipes approaches being a scourge in many parts of the world, .choking waterways and hindering transport upon them. At the same time it is known to readily abstract heavy metal ions from water and, thus, aids in the removal of heavy metals found in such waters. This paper considers the possibility of using specific parts of the plant as an inexpensive adsorbent for the removal of heavy metals from contaminated chemical and mining industry waste waters. In particular the root of the plant was found to be an excellent accumulator of &apos;heavy metal ions including uranium from solution. It is. also suggested that dried roots of the plant ?might be placed in simple bags and used in a very low cost metal ion removal system.

Jan 1, 1995

By Filippos Patsiogiannis

Laboratory size (5 kg) aluminum killed low carbon steel melts were desulfurized with synthetic fluxes in zirconia crucibles. The sulfur, oxygen, aluminum, silicon, and manganese contents in the melt were determined as a function of refining time and temperature. With a good argon shield and synthetic flux cover, melt reoxidation was not observed. Sulfur removal followed first order reaction kinetics. The effectiveness of calcia saturated calcium-aluminate (12CaO.7Al2O3) based fluxes in desulfurizing the steel melts was evaluated. The effects of initial sulfur level of the melt, weight of the flux (slag), and additions of tellurium, fluorspar, and barium oxide to the melt on the kinetics of desulfurization were also studied.

Jan 1, 1993

By Hebi Yin

A two-dimensional multi-scale solidification model was developed to study the heat transfer, fluid flow, and grain growth occurring in the molten pool during the laser engineered net shaping (LENS) process. This model coupled the finite element method to calculate mass, energy and momentum transport in the macroscale with the cellular automaton technique to calculate liquid/solid phase change at the microscale. The validation of the model was performed by comparing the simulation results with experimental data from previously published works, showing good agreement in temperature distribution and the dendrite morphology (size and shape). The simulation results showed that Marangoni convection, caused by the temperature gradient along the pool surface, played a critical role in determining the flow pattern in the molten pool and exerted influence on the pool size and shape. It was also found that columnar dendrites can be formed, with dendrite arm spacings as fine as a few microns due to the high cooling rate during the LENS process. In addition, the influence of fluid flow on the dendrite growth in the pool was discussed.

Jan 1, 2010

By Robert A. Medower

This paper will review the operational benefits of applying contemporary control technology to balance the blast to a cupola. Reported benefits from existing installations include reduced channelling, higher pour temperature, reduced oxygen consumption, lower coke consumption & reduced emissions.

Jan 1, 2001

By E. S. Geskin

"This paper is concerned with the construction of a formal technique for the selection of a metallurgical technology. Exergy consumption is used as the criterion of process efficiency. Different items of the exergy balance are considered and techniques for the reduction of exergy consumption are determined. The selected techniques of exergy saving enable us to identify processes which should be used at different stages of steelmaking. The combination of the selected processes enables us to suggest a technology for conversion of iron ore into steel products. The selection of this technology narrows the range of further search of metallurgical processes. The paper shows that qualitative thermodynamic analysis can be used as the first step in the design of metallurgical processes. IntroductionThe existing processes for making, shaping and treating of steel enable us to convert the available iron bearing ores into marketable steel products. However, the energy cost of metal production is much higher than thermodynamically required, while the metal properties are much lower than thermodynamically available. Increasing cost and declining availability of energy and raw meterials make the creation of new steelmaking technologies imperative. In recent years, the number of novel processes for the making, refining, and shaping of steel have been suggested and tested. Some found a practical application. However, the tested technologies make up a small portion of the physically available routes for the conversion of iron ore into a marketable product. It is also not evident that the optimal routes have been tested and that the selected technologies are the best among those tested.Although the development of new metallurgical technologies must be based on the experimental and practical information, the number of the alternative routes for the making, shaping and treating of steel, as well as the cost of examining each single route, make necessary the use of analytical techniques for the evaluation of the possible ways of process development."

Jan 1, 1988

The direct removal of lead ions from D2EHPA-kerosene using metallic zinc as the reducing agent was evaluated. The electrochemical process, called galvanic stripping, is a potential alternative stripping technique when standard chemical methods are not adequate. Four parameters found to be important in the rate of lead removal were studied in a factorially designed experiment. The variable evaluated included D2EHPA concentration, temperature, zinc surface area and solution agitation. Temperature and surface area were found to be the most significant, while agitation and D2EHPA concentration had less influence on the reaction. An activation energy of 22.5 Kcal/mole was calculated indicating a chemically-controlled process. The reaction was also sensitive to the concentration of oxygen in the system. The zinc required was considerably in excess of stoichiometry, possibly due to the dissolution and redeposition of lead: In general, the results were encouraging and demonstrated that lead impurities could be removed from D2EHPA using cementation type reactions.

Jan 1, 1995

By Huimin Lu, Lian Zhou, Qiang Li

"A three-dimensional mathematical model is developed for the regenerative rotary hearth furnace with 40 meters medium diameter. The influence of combustion switchover and outlet pressure on the fluctuation and distribution of temperature and pressure is studied with numerical simulation method. The results showed that the temperature field and flow field is suitable for requirement of industrial production; the fluctuation of the temperature field and pressure is acceptable; the influence of outlet pressure on the furnace pressure is great.IntroduceRotary hearth furnace which is originally utilized as heat treating and reheating industrial furnace, now is also used for carbon based DRl production. With the need of market and the concern of resource recycling and environmental issues, the DRl production from ore or from waste material by rotary hearth furnace attracts more and more attentions from steel industry [1,2].When rotary hearth furnace works, the feed pellets are charged on the hearth and rotate within an annular furnace chamber with the process of reduction. For the sake of rapid reduction, usually the depth of the pellet is one or two layers, accounting for less than 90% of the volume of furnace. As result, the exhaust gases carry away a lot of heat, so that energy utilization efficient is low [3]. Currently, in order to reduce the consumption of energy and improve the production efficiency, many methods have been adopted. The regenerative combustion technology is one of the most promising."

Jan 1, 2013

By Richard W. Lawrence

Leaching of copper from sulfide minerals using biooxidation offers a potential route for copper recovery. Oxidation of . sulfide sulfur can proceed either; to sulfate or to elemental sulfur depending on mineralogy and process conditions. The advances in commercial application of biooxidation for sulfidic gold ores has made available operating and cost data which allow the derivation of conceptual costs for copper ore processing for comparison with conventional processing routes. Although costs for copper biooxidation generally remain high relative to conventional smelting, application might be competitive in specific cases. Biooxidation becomes more competitive in the general case if the cost ofS02 emissions in pyrometallurgical processing were to be internalized to a greater degree than currently required. This paper describes the technical aspects of biological processing of copper sulfide ores and concentrates, specifically with respect to the fate of sulfur. The environmental and economic implications of the biooxidation route are discussed in relation to conventional processing.

Jan 1, 1996

By H. Shang

The materials science and metallurgical engineering communities have expended enonnous resources in developing high fidelity process models. Exploiting these Models for Predictive Optimization (MPO) and Control (MPC) is a new frontier in Materials Process Engineering that will lead to exceptional process perfonnance. This paper will begin with a short survey of the development of high quality process models available in the literature and a discussion of how these could be used to improve process operation. A summary of the current "state-of-the-art" in process automation technologies and the traditional framework in which these technologies are deployed will be presented. An illustration of the use of MPO in process design and operations will be presented for the continuous casting of steel. In addition, a simple run-out table simulation will be used to demonstrate the power of the MPC technique.

Jan 1, 2003

By J. S. Becker

Technology developed and first implemented in the United Kingdom enables very low grade aluminum scraps containing oils, organics, plastics and ferrous metals to be directly charged, without pretreatment, into a unique melting furnace. The system has been in full scale production for over three years. The oxy-fuel-based furnace design incorporates internal afterburning in the furnace&apos;s hot zone, producing excellent thermal efficiency and very low emissions. The furnace is inherently low in NOx. This paper will provide both theoretical background and extensive operating results for this new melting concept. Applications describing both purpose built new furnaces and retrofits of existing reverberatory furnaces will be presented. Extensive operating emissions data will be presented.

Jan 1, 1996