Search Documents

By Z. Sun

Magnetic fields have been used for inclusions removal from melt and preparation of materials with gradient compositions. Fundamental in these applications is that the induced magnetic forces on the particles/melt can enhance migration and change the interaction behavior. In the present paper, migration and interaction behavior of electrical-insulating particles in a conductive melt under strong magnetic field are theoretically analyzed. It is found that the migration can be considerably enhanced for micrometer sized particles by applying a strong magnetic field. In addition, two forces are involved in the interaction between two particles: the interparticle magnetic dipole-dipole attractive force due to magnetization and the repulsive force induced by flow of the melt. This theoretical analysis renders a better understanding of recent experimental results. Additionally, a new method by using strong magnetic field can be proposed to control the particle size distribution for the preparation of metal-matrix composites.

Jan 1, 2009

By James M. Fragomeni

"The mechanical behavior of an Al-Li alloy was studied and related to the extrusion processing parameters, the plastic metal flow during defonnation, the anisotropy, and the microstructure. The extrusion temperatures, strain rates, extrusion ratios, billet temperatures, and extrusion geometries were varied during processing and correlated with the microstructure and properties. The extrusion processing variables were related to the mechariicar behavior, anisotropy, and microstructure through the ZenerHollomon parameter i.e., the temperature compensated strain rate. Based on optical and electron microscopy studies it was found that regardless of the extrusion conditions, the various microstructures for the most part were unrecrystallized for both the as-extruded and the solution heat-treated conditions. Smaller grain sizes were correlated to larger Zener-Hollomon parameters. The extrusion temperature and ratio did not significantly affect the strength or ductility as did the section geometry, which had a large affect on these mechanical properties. The anisotropy of the properties varied substantially when comparing the extruded longitudinal versus transverse grain orientations.IntroductionThe extrusion process also has a substantial influence on: the microsfructure and mechanical properties of a material that is Athens, Ohio, 45701 fonned The plastic defonnation that occurs during the extrusion process alters the grain size, crystallographic texture, anisotropy, subgrain size, dislocation density and various other microstructural features. Often the material being extruded is not homogeneous, therefore variations in the microstructure and properties occur across the cross-section of the final extruded product. The mechanical properties and microstructure can also vary with length since it is hard to maintain a constant temperature throughout the extrusion process. The extrusion temperature often varies from the heat generated during the extrusion process. The demonstration material that was extruded for this .study was an aluminum alloy containing 2.6wt, % lithium and 0.09wt.% zirconium. This alloy was strengthened by heat treatment causing nucleation, growth, and coarsening of coherent metastable o' (Al3Li) precipitates in the microstructure. The ? precipitates which are a consequence 9f artificially aging the AlLi alloy, are spherical, ordered, and coherent with the aluminum matrix and impede the dislocation glide inotion during plastic defonnation. Theo particles grow homogeneously in the matrix, and have the Cu3Au (L 12)"" superlattice crystal structure. Aluminum-lithium alloys are used primarily for aerospace structural applications since they have attractive properties such as a lower density and higher elastic modulus than conventional 2XXX and 7XXX alloys."

Jan 1, 2000

By M. J. Collins

Direct pressure leaching of zinc sulphide concentrates was started? commercially in October 1980. Continuing research and development studies at Sherritt and feasibility studies for a number of clients have defined various pressure leach configurations for integrattons with existing roast- 1 each operations and for grass roots plants. Existing and potential applications of zinc pressure leaching are discussed.

Jan 1, 1990

By Sutham Niyomwas

The Fe-TiC composite powder was synthesized in situ by carbothermal reduction of ilmenite. The standard Gibbs energy minimization method was used to calculate the equilibrium composition of the reacting species. The effects of the reaction temperature (1300 °C - 1500°C) and milling time of precursors on the Fe-TiC conversion and powder morphologies were investigated using XRD and SEM method. The synthesized products showed that composite with iron matrix and titanium carbide as a reinforced phase was formed.

Jan 1, 2006

By Jiakai Zhang

Many postconsumer electrical and electronic equipment wastes contain a considerable amount of rare earth elements (REEs); however, the current level of REE recycling from them is limited (<1%). Neodymium–iron–boron (NdFeB) magnets, used at both small- and large-scale, from computer hard disk drives and small tools to wind turbines and cars, are a good example of such waste materials that contain high content of neodymium (Nd) and dysprosium (Dy). These elements are considered critical metals because they are the main building block of emerging green technologies that will allow for GHG emission reductions. Because demand for these green products is increasing around the world, the demand for REEs is increasing quickly, putting their supply at risk in the near future. Thus, it is critical to develop efficient, robust, and cost-effective processes to recycle these elements from this class of electronic waste materials. Here, we performed a thorough characterization of a N52–NdFeB magnet to identify its composition, crystal structure, and morphology. Furthermore, we developed an efficient hydrometallurgical process to extract Nd and Dy with high efficiency (more than 95%).

By W. K. Connor, O&apos

Thermal Treatment Technology Division Albany Research Center, U.S. Dept. of Energy Oregon. This evaluation included a characterization study and direct smelting tests conducted in a bench-scale electric arc furnace (EAF). In contrast to other thermal treatment technologies considered for these wastes (i.e., fluidized bed combustion), direct smelting in the EAF can process 100% of the wastes without prior beneficiation, and utilizes solid oxidant additions (in this case iron ore) rather than air to oxidize the carbon. This solid oxidant addition is advantageous because it results in the production of several value-added furnace products. These products include cast iron resulting from the reduction of the iron oxides, baghouse dust containing virtually all of the zinc from the residues, and a clean (nonhazardous) slag product suitable for recycle as concrete aggregate or construction fill. Offgas from the smelting furnace also holds potential as fuel gas for cogeneration. The direct smelting tests conducted thus far were successful at producing the desired furnace products, exhibiting the potential for complete recycle of the waste pile. A cast iron product of comparable quality to conventional cast irons was produced, at nearly 80% iron recovery to the metal. The slag product was determined to be nonhazardous, based on the EPA TCLP. Lead and zinc partitioning to the dust product was greater than 99%. The material balance over the furnace indicates that for every ton of feed processed, 540 lb. of cast iron, 600 lb. of slag, and 150 lb. of dust would be produced. Energy consumption was roughly 1.10 kWxh/lb of feed material. Prior experience suggests that these figures measured in the bench-scale furnace would translate to 0040 to 0.50 kWxh/lb at the industrial-scale.

Jan 1, 2000

By Liming Wang

One of the steps in the extractive metallurgy of lead is a refining process called drossing. Hot dross is mixture of impurity compounds that form on the surface during the cooling of lead blast furnace bullion, and in Missouri, the main impurities are copper and sulfur. The slow cooling of bullion throws out of solution all other minor impurity elements (or their compounds) which are much less soluble at lower temperatures (mainly nickel, arsenic, iron, and zinc). The transfer of bullion from the blast furnace to the refinery and the subsequent hot drossing step cause fugitive emission of lead-containing fume and dust, which creates a plant hygiene problem. One cause of the emissions is the high vapor pressure of lead and its compounds during transmission of = 1000 °C bullion to the drossing kettle. Another cause is the lifting of dross dust during manual skimming of dross. The environmental problems associated with the traditional hot drossing process provided an incentive to investigate a new drossing process that avoids contact between plant air and hot bullion or dross. A key aspect of the process development was a detailed mineralogical examination of dross from two different bullions. The bullion samples were cooled at different rates, and the dross filtered out and examined. The morphology, phase identification, and composition of the dross was examined by optical and SEM microscopy. The principal dross phases were copper and cuprous sulfide, galena, a complex sulfide containing copper, nickel and lead, and speiss (containing nickel, cobalt, iron, copper, lead, and arsenic compounds). The copper was acicular, with nickel and arsenic in solid solution. The cuprous sulfide was largely digenite in a granular or dendritic form. A substantial part of the dross was solidified matte with a eutectic microstructure, consisting mainly of CU2S and PbS. Small particles (some of which had a eutectic microstructure) never floated to the surface of the lead during the slowest cooling rate, thus indicating that flotation of tiny matte droplets and dross crystals is exceedingly slow. The success in separating dross and lead by centrifugal filtration suggests its application in industry as a replacement for traditional hot drossing.

Jan 1, 1995

By Tiebao Yang

In high pressure die casting processes, a die plays a critical role in removing heat from the molten metal during the cavity filling and solidification stages. Proper control of die temperature is essential for producing superior quality components and yielding high production rates. This paper proposes a local temperature control scheme for die thermal management based on a computerized intelligent real-time monitoring and control system (IRMCS). In this scheme, cooling water lines are controlled by a pump and solenoid valves. A controller is designed according to the law of die temperature fluctuations. The results obtained from the experiments carried out on a laboratory die casting process simulator indicate that the controller can limit the local die insert temperatures in a given band. Hence, the desired thermal pattern of the die insert becomes achievable.

Jan 1, 2006

By R. H. Eric, P. Taskinen, A. Bhalla, P. Halli

Sustainable development requires less energy consumption with lower carbon footprint. In this review the solid state reduction behaviour of three oxide ores using methane gas are briefly summarized based on experimental work conducted in our laboratories. The discussion concentrates mainly on mechanisms of the reduction studied through SEM-EDAX and X-ray diffraction techniques. Limited preliminary kinetic input is also mentioned. Iron ore containing titanium and vanadium could be reduced significantly in the solid state with methane-hydrogen mixture up to 400 °C lower than is needed in ordinary solid state carbothermic process. The reduction of chromite and manganese ores were possible similarly at lower temperatures with potential energy savings lower carbon footprint.

Mar 1, 2017

By Yunhua Gan, Xiaowen Chen, Yang Tong

Experimental studies of electro-spraying were carried out using ethanol as fuel in a microcombustor under combined electric field. And the effects of different electro-spraying modes on the combustion efficiency were analyzed. Results showed that when ring electrode potential was invariant, there were four different electro-spraying modes with the variations of nozzle potentials, which were varying with the flow of ethanol. The cone-jet mode was the stablest one during the whole experimental process. The atomized ethanol was ignited and combusted stably near the steel mesh, the combustion efficiency increased firstly and then decreased along with the increasing of the equivalent ratios, reached the maximum values when the equivalent ratio equal to 1.0. And the maximum values were the highest at the cone-jet mode, and the lowest at the pulsed-jet mode.

Jan 1, 2016

By Garry W. Warren

The brass foundry industry produces a significant amount of waste sand containing Cu, Zn and Pb which is often classified as a hazardous waste due to Pb content. The potential application of a hydrometallurgical process to treat the sand by extracting metal values and thus detoxifying the material has been investigated. The process involves leaching of metal values followed by cementation. The emphasis of this investigation was on the leaching step, although some preliminary cementation experiments have been performed. In order for any alternative treatment scheme to be successful, the smaller size fractions of the sand must be addressed. Experiments have been performed on five individual size fractions using various lixiviants HCI, acetic acid and HCI/NaCI. Cu extraction was found to be slower than either Zn or Pb. Results obtained in this investigation indicate that copper is present in two forms, an oxide form which dissolves rapidly and is insensitive to the level of oxygen, and a less soluble form, probably metallic which dissolves more slowly and requires an oxidizing agent. The presence or absence of oxygen had no influence on the rate of Zn dissolution indicating that zinc is present mostly in oxide form. Toxicity Characteristic Leaching Procedure (TCLP) tests showed that residues could be produced which meet the toxicity limit for lead. Preliminary cementation experiments have also demonstrated the feasibility of Cu and Pb recovery.

Jan 1, 1991

By R. Fragoudakis

AISI 4130 steel is a medium carbon Cr-Mo steel used in automotive, aeronautic and other general-purpose industries. In this study, 4130 steel fatigue specimens were carburized at 927oC to enhance the carbon content in the steel, raising it from approximately 0.30% (non-carburized) to 0.90% (carburized, oil quenched and tempered). Rotating bending fatigue tests were performed on the R. R. Moore Rotating Beam Fatigue Testing System, in order to determine the high cycle fatigue (HCF) life of 4130 steel and plot the corresponding S-N diagrams. A comparison of the results of carburized and non-carburized specimens shows that carburizing of steel: a) increases the surface hardness and b) improves the fatigue strength of the steel by at least two orders of magnitude.

Jan 1, 2010

By Isabella Lancellotti, Fabrizio Passarini, Luisa Barbieri, Fernanda Andreola, Ivano Vassura, Luciano Morselli

"The techniques able to incorporate wastes by means of a heat treatment present the advantage to fix the residue with chemical bonds. Among these techniques there are vitrification and sintering which are characterised by different operating temperatures in the range of 950-1500°C and the involved raw materials develop silicatic crystalline phases and glassy matrices capable to immobilize heavy metal contents in the waste matrix. In this work incinerator bottom ash, polishing and glazing ceramic sludges have undergone to thermal treatments in order to valorise the waste as secondary raw material for the obtainment of re-products. The chemical efficiency of the process adopted has been evaluated by comparing the results of release tests applied to the as-received wastes and to the thermally treated materials in order to verify the effectiveness of the different matrices to fix the waste components.IntroductionVitrification is one of the most promising technological options for the treatment of some kinds of waste. The high temperature involved in the process (1200-1500°C) leads to the complete destruction of organic pollutants, such as dioxins, and glassy network formed can incorporate heavy metals. Some vitrification processes naturally occur: glasses produced by volcanic eruptions, such as obsidians (Na2O-K2O-Al2O3-SiO2) and basaltic (CaO-MgO-Al2O3-SiO2) rocks, are basically inert materials even when they contain toxic elements, because these are embedded in an extremely stable glassy matrix. The disadvantage of vitrification is that it is an energy-intensive process involving relatively high costs, therefore its use is better justified if a high-quality product with optimised properties can be fabricated. The most effective way to improve the properties of the vitrified material is the transformation into glass ceramic. This is a fine-grained polycrystalline material (typically from 50% to 98% of the volume may be crystalline) formed when a glass of suitable composition is heat treated and hence undergone to controlled crystallisation (phenomenon named devitrification). The three key variables in the design of a glass-ceramic are: glass composition which controls glass viscosity related to the effectiveness of nucleation and rapidity of crystallisation; glass-ceramic phase assemblage (that is, the types of crystals and the proportion of crystals to glass) which is responsible for many of the physical and chemical properties; nature of the crystalline microstructure (crystal size and morphology and the textural relationship among the crystals and glass) which is the key to many mechanical and optical properties. In particular, a partly crystalline material can be obtained by powder sintering."

Jan 1, 2008

By Richard B. Stein

Bechtel&apos;s BEMSIM computer program is a useful tool for solvent extraction-electrowinning plant design optimization. Its power (up to 90 stream components, 240 process streams, 180 process steps) has been applied to investigate floweheet configurations in order to perform basic engineering, sizing of plant equipment and to optimize performance of commercial-size copper plants. Flowsheet variations presented include series, parallel and series-parallel extraction stages, while heat balances simulate operations in summer and extreme winter conditions. The BEMSIM program has also been applied to nickel-cobalt, gold and manganese extraction.

Jan 1, 1993

By Richard A. Leiby

The recycling of lead-acid batteries in the United States has become a challenge as to how to balance ever increasing environmental regulation and cost with efficient operations. East Penn&apos;s captive secondary lead smelter has developed into a recycling facility producing lead, polypropylene, sulfuric acid, ammonium bisulfite, and non-hazardous discard slag. The emphasis has been to design a facility to comply with environmental regulations, to eliminate wastes, and to produce products, while at the same time, continuing to supply the company&apos;s battery manufacturing raw material needs.

Jan 1, 1993

By Houyuan Liu

A new process was developed to recover nickel and cobalt by leaching laterite ore at atmospheric pressure and.95"-105" C. The nickel-containing goethite in limonite was first leached with sulphuric acid to liberate over 90% of nickel, cobalt and iron. The dissolved iron was then precipitated as Ni-free goethite by the additioil of saprolite. The acid released during iron precipitation as goethite was simultaneously used as lixiviant to leach saprolite to recover more nickel. With this process the limonite and saprolite were essentially converted into goethite-, gypsum- and silica- containing tailings. Twenty bench scale tests and two campaigns of pilot plant operation were carried out at BHP Billiton&apos;s Newcastle Technology Centre (NTC) from January to August 2002. The overall nickel and cobalt extractions were 81 to 90% and 91 to 100% respectively. The average plant availability was 99%. The advantages of this process over existing processes include high plant availability, high consistency, robustness and simplicity of the operation.

Jan 1, 2004

By Claudia Gasparrini

Uranium occurs in a variety of minerals, the more common primary ones of which are uraninite-pitchblende, coffinite and a group known as the complex multiple oxides. Identification and description of the uranium-bearing and associated minerals in ore samples may give a preliminary indication of the potential economic importance of the deposit and may also suggest initial approaches to metal extraction. The present paper reviews the common uranium minerals, describes their manner of occurrence and compares the types of deposits with which they are associated. Methods and techniques for their identification are described and their leaching characteristics discussed.

Jan 1, 1981

By Yuanbo Zhang, Zijian Su, Bingbing Liu, Guanghui Li, Jicheng Liu, Manman Lu, Tao Jiang

Blast furnace slag (BFS), one kind of typical solid waste in the steel industry, was used as structural materials to synthesize NaNO3/BFS composite phase change materials (C-PCMs) by mixing and sintering method. NaNO3 in the composites functioned as phase change materials (PCMs) and BFS as structural skeleton to maintain a stable external form. In this study, the prepared C-PCMs could remain in the solid state without salt leakage even if operating temperature exceeded the melting temperature of NaNO3. The composition and structure of BFS and the prepared composites were characterized by XRD, FTIR, SEM and TG-DSC analyses. The results showed that NaNO3 was well incorporated in the pores of BFS. The melting temperature and latent heat of the final composites were 300.5 °C and 65.53 J/g, respectively. The product also had good thermal storage performance and durability even after 100 thermal cycles. The energy density of the product was calculated as high as 468.03 J/g for an temperature range of 50–400 °C.

Mar 1, 2018

By Reinhard F. Dobner

After a short introduction about the HK&apos;s secondary smelter process and explanations concerning the anodes produced the regulation and buffering of bleed will be described and the principles of technology for processing of bleed will be presented. Modernization aspects, especially installation equipment, and the different types of evaporators used will be described in detail. Besides, experience made with acid-resistant materials - stainless steel, enamel, plastics - will be reported. Environmental aspects such as water and air pollution will be outlined briefly and in conclusion the quality of products obtained as well as quality control will be presented.

Jan 1, 1997

By Zhao-feng Xie

A new process of recycling valuable metals containing in the slag of jamesonite smelting in the blast furnace was studied. In this process, the valuable metals such as Pb, Sb, Zn and In etc. were fumed and volatilized and enriched in the dust firstly and then the dust was leached by sulfuric acid. In the leaching procedure, Zn and In in the dust entered into the leaching solution and were separated from Pb and Sb which remained in the residue.The optimal operation conditions of the fuming procedure are as follows: the mass ratio of the blast furnace slag, coal powder and lime are 100:22:10 respectively and the fuming time are 1.5~2.5 h, the fuming temperature is not below 1200C and the volatilization rates of Pb, Sb, Zn and In are 95%, 92%, 86% and 75% respectively. The optimal conditions for the leaching procedure are also presented: the consumption of sulfuric acid is 1.15 times of the theoretical consumption, the ratio of liquid to solid is 4:1 and the leaching temperature, leaching -1time and stirring speed are 90, 1.5h and 300 r?min separately. The leaching rates of Zn and In are 98.5% and 95.2% respectively. The experimental results shows that the valuable metals in the dust can be recovered and separated effectively by this process and the?ir recovery efficiencies are as follows: Pb94%,Sb91%, Zn84% and In69%.

Jan 1, 2009