Search Documents

By Tsisana Gagnidze

A processing of technogenous wastes, which involve a gold-containing sulphide minerals, is a potential source to supplement the gold reserves. Hence, searching of ecologically safe and economically reasonable methods for processing of gold-containing technogenous wastes is a topical problem. To increase a parameters of gold extraction and to simplify a technology of the processing of above-mentioned wastes of sulphide minerals, an investigations have been carried out in the direction of the use of the method of electrochemical leaching without any preliminary processing of the mineral. It was established experimentally that an introduction of nitrogen containing organic additive into chloride solution favours to reduce a Red/Ox potential of the solution from 0,8÷1,2 V to 0,35÷0,5V, which permits to conduct the process of direct electrochemical leaching at ?soft? oxidation regimes at temperatures 20-300C C without an environmental contamination by molecular chlorine and with a high degree of a gold extraction up to 80-90%.

Jan 1, 2008

By Masaki Imamura

A novel hydrometallurgical process for copper concentrate treatment has been developed by Niihama Research Laboratories of Sumitomo Metal Mining Co., Ltd. The process has numerous advantages with respect to the operational and environmental aspects. For example, copper is leached effectively from chalcopyrite concentrates by chlorine gas under atmospheric pressure. The copper in the leach solution is then separated from iron and silver by solvent extraction and undergoes electrowinning for its recovery as a highly pure copper metal; this does not require any further purification. Moreover, iron metal can be produced from the purified raffinate by electrowinning without generating a large volume of goethite or hematite, which are solid wastes generated due to iron rejection in common hydrometallurgical processes. This process can also realize the efficient recovery of precious metals. The results of batch testing and continuous-operation testing are presented in this paper.

Jan 1, 2006

By Chuan-fu Zhang

Li(Nil/3Col/3- xMnl/3)MxO2(M=Ti, Mg) cathode materials were prepared from LiOH?H2O and oxalate precursor. The physical and electrochemical properties were studied by XRD, SEM, cyclic volt-ampere (CV), AC impedance and constant current charge-discharge. The results show that crystal volume of Ti4+ or Mg2+ doped sample is increasing and the electrochemical reaction resistant Rct is decreased at high rate, improving the cyclic performance and rate capability. The effect of Ti4+ doped is better than Mg2+. The sample is well crystallized and simple pure phase with a-NaFeO2 layered structure when doping quantity x=0.025. The second specific discharge capacity of Li(Nil/3Col/3- 0.025Mnl/3)Ti0.025O2 is 143.2mAh/g at 1C,128.0mAh/g at 2C in the voltage of 2.75-4.3V,and still has 140.7mAh/g and 121.7mAh/g after 20 cycles, respectively, keeping 98.25%, 95.07% capacity.

Jan 1, 2009

By Bin Du

In recent years, concurrent product design and process is gaining popularity and will become a norm of the industry of the future. Forging has been a critical manufacturing process for production of components with superior tensile strength, toughness and grain flow. This paper describes an expen system which is being developed for forging die design and forging process analysis in concurrent engineering environment. Rules and guidelines pertaining to forgeability are formulated and incorporated into the knowledge-base in building the system. The system is built using an object-oriented paradigm. The object-oriented approach and hierarchical rule structure paradigm are briefly discussed. Finite element analysis packages (ALPID-2D) were incorporated into the program to give the simulation result of the forging process. The system can automatically produce a competent design and recommend a set of processing parameters for a given product. The designer can modify the design according to the result of the simulation.

Jan 1, 1992

By S. Street

The Environment process, invented by Prof. H.K.Womer and developed at the University of Wollongong, simultaneously treats ferruginous and organic wastes via bath smelting. Conceived in the late 1980's, the patented process was originally developed using steelworks dust to settle solids from sewage, producing a composite material suitable for smelt reduction. Work began on the process in 1990 with the Australian patent having a priority date of February 1990. Early research focussed on settling of solids from sewage, while pyrometallurgical investigations examined smelting in small induction furnaces. By 1992 smelting trials had been undertaken in pneumatic and electric arc furnaces, the process being successfully demonstrated up to on 8 tonne scale. The success of this particular trial, and other smaller trials, resulted in construction of a 100kg DC arc furnace which was commissioned in 1993. By 1994 the main project focus was on development of the smelting technology. Over 3 years of trials on the DC arc furnace have identified and clarified many of the pyrometallurgical reactions. optimum operating parameters, as well as demonstrating the versatility of the process for treating a wide range of wastes. Currently the Illawarra Technology Corporation (lTC), the commercial arm of the University of Wollongong, is pursuing commercialisation of the process.

Jan 1, 1996

By Zhang Jianliang, Zuo Haibin, Gao Bing, Wang Zhe

"As a result of the shortage of coking coal and the quality decrease of coke, it is important to know how to make better use of highly reactive cokes. The co-gasification behavior of highly and lowly reactive coke for blast furnace is investigated. The results show that: In the middle stage of reaction, the weight loss ratio of highly reactive coke reacted together with lowly reactive coke is higher than that of it reacted individually. However, the weight loss ratio of lowly reactive coke is lower. The weight loss ratio of highly and lowly reactive coke is almost the same as that of the weighted average. The scanning electron microscope analysis indicated that the reaction degree of surface and interior of lowly reactive coke is relatively uniform with the reaction time increased. And the reaction degree of surface of highly reactive coke is obviously higher than that of interior.IntroductionIn blast furnace iron making process, coke functions as heat supplier, reducing agent, carburizer and skeleton. With development of blast furnace iron making technology, the skeleton function of coke is becoming more and more important in requirements of large scale furnace and high pulverized coal injection. High reactivity coke is usually produced by cheap coal with bad quality, and is not good for blast furnace process. The reactivity of coke is mainly determined by the coals used, and the resource of good quality coking coal is limited and is non-renewable. In order to fulfill the need of blast furnace, a lot of research have been done to improve coal matching using new kinds of coal to enlarge resource, in which coking coal and fat coal are reduced, whereas low price coal with bad caking property are used to lower the cost, and this would inevitably increase the reactivity of coke [1-4] Blast furnace iron making would still be the main stream for a predicted future, and high reactivity coke would correspondingly be used more and more, so it has great importance to study how to use high reactivity coke in blast furnace."

Jan 1, 2013

By Beatryz C. Mendes, Henrique de Paula Santos, Kléos M. L. Cesar, Eduardo Antônio G. Marques, Maurício Paulo F. Fontes, Rita de Cássia S. S. Alvarenga

Inadequate discard of industrial solid waste is a risk to human health and to the environment. Aiming at softening environmental damage caused by deposition on soil of an ink residue, from washing of printers used in carton box packages, it is intended to incorporate this residue into soil-cement bricks. The residue has other use potentialities such as in screeds, pavement parts, fertilizer, paints, etc. However, to explore these potentialities it is fundamental to assess the risks that the several forms of use of this residue can cause. For such, in this work the chemical analysis of the residue was performed in order to know its main chemical compounds, in addition to its characteristics of leaching and solubilization. The chemical composition assay showed traces of some heavy metals such as Pb, Cd, Cr, Zn, Al and Cu, although the residue-generating company uses ink labeled as heavy metals free. Among the elements analyzed in leaching and solubilization, some had concentration above the limit allowed by The Brazilian Codes. This code is based on CFR—Title 40—Protection of Environment—Part 260–265—Harzardous waste management. Therefore, it is suggested that the residue has a limited use to avoid contamination of ground water.

Mar 1, 2017

By H. Y. Sohn, M. K. McCarter, Bradley C. Paul

"A computer model was constructed for bacterial leaching of the major sulfides found in porphyry deposits, including bornite, chalcocite, chalcopyrite, covellite, cubanite, enargite, native copper, pyrite, and pyrrhotite. The model incorporates equations for the sulfide minerals dispersed in the rock matrix. Leaching occurs by reactions with ferric ion diffusing into the rock fragment: Ferrous ion is resenerated to ferric with oxygen by bacteria at a temperature dependent rate. The model keeps track of the net acid generated, oxygen consumed by the bacterial oxidation of ferrous ion, heat generated, jarosite and hematite precipitated, and copper leached. The model was used to predict the rate of copper recovery, heat generation and oxygen demand for a variety of run-of-mine sized porphyry ores. These results were used in the design of a ventilation system and the economic analysis of a modified in situ extraction method that may be cost competitive with conventional copper production involving open pit mining.IntroductionA study was undertaken at the University of Utah to evaluate the technological and economic feasibility of mining copper by a method referred to as Flood Drain Leach Cell (FDLC) mining. Cells 60 by 75 meters in plan and 70 meters in height are created throughout the ore body by a modified Vertical Retreat Mining technique that includes the removal of 25% swell material. The swell material is leached in finger dumps on the surface while the cells underground are bulkheaded, flooded, drained, and artificially aerated to promote bacterial ferric sulfate leaching. Solutions are cycled through several cells to reach pregnant grade of 1 gram copper per liter of solution. These solutions are then fed to an underground solvent extraction plant and then a surface electrowinning tankhouse."

Jan 1, 1988

By W. F. Ranson, R. C. Progelhof

"I. THE PROBLEM: MANUFACTURING PRODUCTIVITYThe 1985 President's Commission [I] on Industrial Competitiveness found compelling evidence of the declining economic position of the United States in world markets. The annual rate of increase in the United States productivity is approximately one-seventh that of our major trading partners over the last decade: profit levels in manufacturing investments are below those of the mid-1960's; an increasingly negative trade balance since 1971; and a sharp decline in the United States share of world trade in manufactured goods for more than two decades. A particularly dramatic example of the shifting economic balance is the fact that Japanese productivity growth has been five times greater than that of this country since 1960. In face, Japan's productivity now exceeds that of the United States in such critical industries as steel, transportation equipment, electronics and electrical machinery.American employees have experienced the competitive consequences of this nation's lagging industrial performance. Between 1980 and 1984 alone, the population of non-farm employees engaged in manufacturing dropped from 22.4% to 20.6%. This reduction in manufacturing must be arrested.Commissions RecommendationsThe comprehensive set of recommendations offered by the President's Commission recognized the nation's ""key competitive advantages"", technology and human resources, and calls for their strengthening. Particular emphasis is placed on manufacturing technology and the fact that this country does not translate research into new technologies rapidly and fully.""Perhaps the most glaring deficiency in America's technological capabilities has been our failure to devote enough attention to manufacturing or 'process' technology. It does us little good to design state-of-the-art products if within a short time our foreign competitors can manufacture them more cheaply. The United States has failed to apply its own technologies to manufacturing. Robotics automation and statistical quality control were all first developed in the United States but in recent years they have been more effectively applied elsewhere""."

Jan 1, 1988

By Aiyuan Ma, Kun Yang, Weiheng Chen, Jinhui Peng, Shiwei Li, Feng Xie, Libo Zhang

In this thesis, a new process of recovering zinc sulfide ores was developed. The novel synthetic coordination leaching process mainly included two steps: microwave assisted phase reconstruction and compound coordination leaching. By applying various techniques, such as chemical composition analysis, X-ray diffractometry (XRD) and Raman spectroscopy, it could be concluded that sulfide phases would directly oxidized to zinc oxides under the 500 ºC microwave roasting and adding 30% Na2O2. What’s more, zinc leaching rate reached to 61.16% within 2 hours. Compared to the current technologies, this procedure had the advantage of avoiding SO2 emission, high leaching efficiency, simple process, manipulate easily, and low cost, which could be expected tremendous application potentials.

Jan 1, 2016

By Carl C. Nesbitt

A study was conducted to examine the treatment of metal-bearing effluents by precipitating the metals as sulfides and simultaneously collecting the particles by flotation. The precipitant was hydrogen sulfide gas which was introduced into a bench-scale column cell with air. The study included experiments of various flotation reagents and column configurations in treating solutions containing dissolved copper, lead, mercury, iron, zinc and cadmium. An acidic laboratory waste from a local copper operation was used to test the column with a solution containing several metals and arsenic. Precipitates were observed to form at the gas/liquid interface when the gas mixtures were rich in H2S. Copper, mercury, lead, and cadmium were precipitated from solution as sulfides to concentrations near detection limits. The flotation of these precipitates was enhanced with small amounts of S-7151 promoter from American Cyanamide Company and Dowfroth 1263 mixed with the feed. The recovery of the precipitates in this manner produced a smaller volume slurry which was easier to dewatering than a slurry produced by conventional precipitation techniques. The low pH and high oxidation-reduction potential in the cell from H2S addition was not conducive to form precipitates of iron, zinc or arsenic. However, these ions were precipitated as sulfides by raising the pH of the column discharge.

Jan 1, 1994

By Kikuo Okuyama, I. Wuled Lenggoro, Manabu Shimada

"Aerosol processing of materials such as (i) gas-to-particle conversion process (e.g., Chemical Vapor Deposition (CVD) method) and (ii) liquid (or droplet)-to-particle conversion process (e.g., spray pyrolysis) has become of major interest to produce novel submicron- or nanometer-sized particulate material used in electronic and chemical industries. After reviewing recent theoretical and experimental researches on the evaluation of properties and morphology of fine particles by the CVD and spray pyrolysis methods, the importance of the process engineering approach· for aerosol processing of materials and the use of advanced aerosol measurement technology have been pointed out.IntroductionMaterial synthesis via aerosol processing offers a route to producing nanometer-sized and submicrometer-sized particles of high purity with specifically tailored chemical and physical properties. Especially, single nanometer-sized particles (nanoparticle materials) are considered to play an important role in the synthesis of nanostructured materials as well as in nanotechnology in 21st century due to their quantum effect and so on.However, the transformation of gaseous or liquid precursors to the final functional particulate matters consists of various complex chemical and physical processes. In order to control the size distribution and morphology of produced particles, it is important to analyze and model various phenomena, such as gas-phase or liquid-phase chemical reaction, nucleation, condensation, agglomeration and sintering that occur simultaneously in aerosol material processing. By introducing the Aerosol Science and Materials Science, the authors have been trying to model the changes in particle properties and morphology by gas-to-particle conversion and droplet-to-particle conversion processes. The authors have also been trying to obtain the experimental data on the particles properties as accurate as possible."

Jan 1, 2000

By Ying Mao, Zhancheng Guo, Long Ma, Huiqing Tang

"A new 2D computational fluid dynamic (CFD) model was developed for the gaseous reduction of iron ore fines in an innovative reactor-multilayer moving-fluidized bed. The solution of the proposed model was performed by integration of FLUENT and PHOENICS. Numerical results of cold state were compared with the experimental data and the agreement between them was good. A hot case-gaseous reduction of iron ore fines using syngas with this reactor was simulated using the present CFD mode. Results indicate that under the given simulation conditions, total pressure drop is 90 Pa less than that under cold state though the gas supply rate is increased about 4m3 under hot state. Gas temperature decreases from 1073 K at the bottom to 500 K at the top, Utilization efficiency of the gas reduction potential is about 27 %. For ore fines reduction, the final reduction fraction could reach 0. 70 and solid temperature 900 K.IntroductionWith the development of coal gasification technology, various coals could be converted to Syngas with air or steam. Therefore gaseous reduction of iron ore fmes becomes an acceptable alternative process for iron making besides blast furnace route[!] and moreover it still has some advantages in processing low grade iron ore fines[2]. Gaseous reduction using fluidized bed technologies is the most competitive in all direct reduction iron-making processes up to now. It has the advantage that ore fines can be directly charged to the process without prior treatment while its disadvantages are particle agglomeration and high gas/solid ratio[3]. To avoid these advantages, a new reactor, multilayer moving-fluidized bed reactor has been developed for carrying out the gaseous reduction. Hydrodynamic behaviors of gas and fines in the reactor were studied and the results were satisfying[4]. However, due to its unique structure of the multilayer moving-fluidized bed and unique gas-solid flow pattern, models of multiphase flow as IPSA, DPM and Eulerian Model could not give a satisfying solution. The current paper is developed a new CFD model and a new solution approach for simulation of the reactive gas-solid flow in the multilayer moving-fluidized bed for its optimization, design improvement and future scale-up."

Jan 1, 2013

By J. C. Agarwal

Slags produced by modern smelting furnaces contain copper values which are unacceptably high for discard. The electric arc furnace is employed commercially to clean copper from flash furnace slags but the addition of highly oxidized converter slags to an electric furnace has created operational problems. Highly oxidized Noranda Reactor slags have not been processed successfully in a pyrometallurgical process. These slags, which contain large concentrations of copper (5 to 10 per cent), are treated in slag concentrators (controlled cooling, crushing and milling, and flotation) which produce a copper concentrate that must be resmelted. Though commercially operable, it will be shown that the slag concentrator has important process and cost disadvantages as compared to a pyrometallurgical process. In this paper an economic comparison is made between a pyrometallurgical process and the slag concentrator. For the analysis, five hypothetical smelting plants are considered. Each plant treats 1200 tons of copper concentrate per day and produces 109,000 tons of copper annually. The plant configurations used in this study are:

Jan 1, 1976

By Kristine Bruce Wanderley, Denise Crocce Romano Espinosa, Jorge A. Soares Tenório

Mining of nickel ores generates large volumes of waste that must be removed in order to eliminate water contamination and reduce environmental impacts created by waste barriers. In this context, the need for innovations concerning the recovery of magnesium present in the liquor produced by the leaching of nickel laterite with sulfuric acid arises. Therefore, this work aims to develop a study regarding the crystallization of magnesium from a synthetic liquor solution using a batch autoclave system at high temperature. Agitation speed was kept constant at 1000 rpm throughout the 3 h of batch reaction for temperatures of 230 and 200 °C. Aliquots taken at each hour were analyzed by ion chromatography to measure magnesium concentration. The highest magnesium removal was observed for temperature 230 °C. X-ray diffraction (XRD) and scanning electron microscopy (EDS-SEM) analysis proved that the product formed was magnesium sulphate monohydrate crystals. Thermogravimetric analysis coupled with a mass spectrometer was used for the evaluation of the thermal stability of magnesium sulphate monohydrate. It was found that MgO and SO2 were formed by the decomposition of the salt at 1100 °C.

Mar 1, 2017

By Tatsuro Ariyama, Michitaka Sato, Atsushi Sakai, Sumiyuki Kishimoto, Ryota Murai

"In order to achieve high pulverized coal injection operation in a blast furnace, optimization of the injection lance arrangement was carried out using an experimental furnace and mathematical models. To increase the injection rate of pulverized coal, it is required to raise the combustion efficiency of pulverized coal. It became clear that multi-point injection and the lance arrangement to avoid interference among the coal streams injected were so effective in increasing combustion efficiency. With these findings, the eccentric double lance arrangement has been newly developed.At NKK, Fukuyama No.4 Blast Furnace, after the improvement of the lance arrangement, the maximum injection rate reached up to 230 kg/thm and an average monthly record of 218 kg/thm was successfully achieved.IntroductionFrom the viewpoints of reducing the production cost of pig iron and prolonging coke oven life, high pulverized coal injection over 200 kglthm is actively pursued by ironmaking industries[1-2].Coal particles injected into the blast furnace are consumed by combustion in the raceway and also in-furnace reaction like solution-loss reaction (C + CO2 = 2CO). The amount of coal consumed by the latter process is determined by the carbon balance in the blast furnace and there is a limit. Therefore, to increase the injection rate, it is desirable to improve the combustion efficiency in the raceway. For these purposes, the optimization of the lance arrangement was examined by a hot model and mathematical models."

Jan 1, 1996

By G. G. Richards

The zinc slag fuming process is used to recover zinc from molten iron-calcium silicate slags by treatment with pulverized coal and air. The rate of zinc fuming is controlled by the complex interaction of several kinetic factors including the rate of entrainment of coal in the slag, the extent of the coal-slag reaction and the rate of ferrous oxide oxidation to ferric oxide. This paper briefly outlines the mechanism of fuming and, on this basis, optimization of process parameters is discussed. Modelling analysis and recent industrial trials at Cominco show that coal entrainment in the slag, bath temperature, and bath depth are critical variables affecting process rate and efficiency. The first step in process optimization is to assess coal bypass of the bath. In general, changes which promote operation at a higher temperature, greater coal entrainment in the slag and extended residence time of the coal in the bath increase fuming performance. Coal entrainment is controlled by injection conditions whereas bath temperature is a function of coal combustion and ferrous oxide oxidation. Residence time of the coal is largely a function of bath depth. The implication of model predictions for continuous fuming is shown.

Jan 1, 1994

By A. A. Hejja

"Liquidus temperature and electrical conductivity data measured on synthetic slags were modelled by the use of neural nets (NN). In this work the applied multilayer feedforward NNs were trained by a conjugate-gradient optimisation for which a three layer formulation was used. Very good fits were obtained for both the liquidus temperature and the conductivity data. The synthetic slags were prepared from pure oxides to represent a wide range of compositions likely to be encountered in ferromanganese and silicomanganese smelting. The slag constituents were in the following range: Mn0;5-30%, Ca0;20-35%, Mg0;5-15%, Si02;27-58%, Al20 3;5%. Liquidus temperatures varied from 1300° to 1380° and increased with increasing basicity ratio. The electrical resistivity of slags decreased with the increase of basicity ratio from 0.55 to 1.1 but above 1.1 basicity ratio the resistivity tended to increase depending upon the MnO content.Neural NetsVarious neural net (NN) topologies such as Hopfied nets, Hamming nets, Carpenter/Grossberg classifiers have been discussed in some detail by Lipmann (1). In this work, the applied multilayer feedforward NNs are not trained by backpropagation (BP) using the generalized delta rule (2) (GDR), but by a conjugate-gradient optimisation [3,4] - a procedure similar to that proposed by Barnard and Cole [5]. A neural net is capable ·of learning the non-linear functional relationship existing between a set of inputs and outputs [ 6]. In this capacity a neural net is used to determine the functional relationship that exists . between N dependent and independent variables, which characterize the system under consideration For a three layer neural net [1] the following function may be formulated, which relates X; inputs to the output Y 0 from node o:"

Jan 1, 1997

By Michael A. Eamon

Magma Copper Company has operated its San Manuel SX-EW Plant facilities since 1986. The original plant facilities have a design capacity of 25,000 tons per year of electrowon copper cathode produced by processing pregnant leach solutions from an open pit/heap leach operation. In 1988, the plant was expanded to 50,000 tons per year to incorporate processing leach solutions from an insitu leaching operation. This paper presents a general overview of plant practices with particular emphasis on process innovations developed and implemented by Magma during construction and operation.

Jan 1, 1991

By Pengfu Tan

In order to understand and control the formation of dioxins and furans in iron ore sinter plants and to possibly avoid expensive end-of-pipe removal stages, thermodynamic calculations on the stability of PCDD/Fs have been combined with sinter process modeling by means of kinetic simulations and computational fluid dynamics. Three thermodynamic databases of PCDD/Fs, derived using the Group Additivity approach and two computational molecular modeling methods, MNDO and PM3, respectively, combined with the SGTE database have been used to model the PCDDIF formation and the PCDD/F isomer distributions in iron ore sintering. The results show very similar conditions for the PCDD/F formation using the different databases. Concerning the isomer distributions of toxic PCDD/Fs, the calculated data derived from the MNDO method showed optimum agreement with measured values from industrial furnaces. The thermodynamic calculations also proved that the isomer distributions found in combustion processes are equilibrium values, while the concentration ratio of PCDDs and PCDFs in the wind boxes does not represent an equilibrium state. A CFD model of iron ore sintering was developed including the kinetics of 15 relevant chemical reactions with the aim of describing the temperature fields and the gas flow patterns in the sintering bed. On the basis of these information and experimental observations reported in the literature possible pathways for the PCDD/F formation in sinter plants have been identified: PCDD/Fs are formed in the critical temperature region of 250 to 450 °C below the combustion zone, are then carried downwards with the gas and condensed close to the bottom of the sinter bed. Transported to the discharge end with the solid mixture, they are again released into the gas phase when the flame front approaches the bottom. PCDD/Fs are also formed in the last wind boxes when the hot off-gases cool down and reach the critical temperature range. Consequently, methods to reduce the dioxin formation reactions are proposed including inhibitor addition to the sinter feed and off-gas quenching.

Jan 1, 2003