Search Documents

By O. Tiitu

Drying is a unit process that has numerous applications in metallurgical process industry. Kumera Technology Center is a worldwide equipment and process supplier, who has expertise on both direct and indirect drying. In a conventional direct heated dryer, the required energy is obtained from combustion of fossil fuels emitting a considerable amount of off-gases. However, thermal energy can be already available in some metallurgical plants such as modem copper smelters where steam is produced by waste heat boilers of flash smelting furnaces. The total volume of off-gases, and especially the amount of harmful gases, released into atmosphere can be remarkably reduced when using steam as an indirect energy source for drying. Kumera Technology Center has developed a new type of steam dryer for drying of, for example, abrasive copper concentrate with silica sand. In the development of the new dryer, Kumera's approach has been to combine the best properties of both the existing steam dryers and the rotating drum dryers. In the design, special attention has been paid to overcoming the reported problems of excessive wear and clogging of steam tubes and to reducing the required maintenance operations. The Kumera Steam Dryer, having a patented flexible steam tube arrangement inside the rotating shell, has a high effective heating area - drum volume ratio without leading to problems with build-up and clogging. It can also be easily scaled up so that a single dryer can dry all of the feed for a large flash furnace. In this paper, we will present the operational and maintenance experiences from two years operation of the first full-scale Kumera Steam Dryer at Norddeutsche Affinerie Aktiengesellschaft in Hamburg, Germany. We will also provide an overview of the future developments with respect to construction and scale up as a response to market demands.

Jan 1, 2002

By H. D. Freeman

The occurrence of gold in refractory gold ores varies widely and affects the recovery process. The determination of gold and the composition of the associated minerals are important in selecting an appropriate processing scheme. However, locating the gold in an ore sample is a difficult task which requires perseverance, luck, and experience. Our experience has led to the development of a relatively fast and reliable means of deter-mining the mineralogy of ore samples through analysis combining an energy-dispersive x-ray analyser coupled to a scanning electron microscope (SEM). In some cases, a wave length dispersive spectrometer or microprobe is used to further quantify the various mineral compositions. The SEM/microprobe analysis identifies the source of problems that may arise during the recovery of gold from refractory gold ores.

Jan 1, 1981

By Boxun Lu, Juan Wei, Kun Chen, Wanlin Wang, Lejun Zhou

"Slag system is an indispensable part during the continuous casting process, and playing various important roles like absorbing inclusions, modifying heat transfer rate, preventing oxidation of molten steel, etc. to ensure the smooth process and excellent slab quality. However most slags contains more than 8% fluorides which tend to introduce a series of environmental and health problems. This study involves the research of the removal of fluorine through the chemical composition optimization. Through the studies of CCT, DHTT, XRD and SEM, it has been successfully founded that the crystalline phase of Ca11Si4B2O22 discovered in this study shows very similar crystallization property as Cuspidine (Ca4Si2O7F2), which is the most important crystalline phase in the current fluorine bearing slags. Moreover, the optimized free/low fluorine slag shows the opportunity to replace conventional high-fluorine mold slag for casting medium carbon steels that is regarded as the bottleneck of green slag development for continuous casting.IntroductionMold flux has been widely used in continuous casting to control heat transfer, lubricate the strand, absorb inclusions, provide insulation and prevent oxidation of the molten steel[1-3]. It usually contains fluorides, like CaF2, NaF etc., which are used to control the viscosity and solidification temperature of mold fluxes [4-5]. However, the presence of fluoride leads to corrosion of equipment, serious environmental pollution (toxic volatiles and water pollution), and high processing cost of cooling water[6-7]. Therefore, the study of low or free fluorine mold flux is of interest and attracts worldwide attention.S. Y. Choi et al. [4] used B2O3 as a substitute for cuspidine in steel B2PB2) however, B2O3 content was extremely high (up to 30 w%). Other studies have investigated F-free mold flux by adding or optimizing components as MgO, Li2O, B2O3 et al[8-11]. However, most of these focused on the melting and viscosity issues or for low or ultra-low carbon steels, where crystallization tendency is not significantly strong. Very few studies regarding to the development of low/free Fluorine mold flux for casting medium carbon (MC) steels have been conducted, due to the difficulty of the crystallization and heat transfer control without the formation of cuspidine."

Jan 1, 2014

By V. A. Luganav

The behavior of arsenopyrite under heating has been studied by many scientists. It has been already established that under heating at more than 650°c and without air access the arsenopyrite dissociates with the formation of one atom arsenic. Under vacuum the dissociation process begins at 5500C with the formation of elemental arsenic. The residue of dissociation process contains pyrrhotite and throilite. In the presence of pyrite, arsenopyrite dissociates under lower temperature and with a higher velocity than without it. The industrial realization of fool scale processing of arsenic bearing raw materials is possible only by the use of standard equipment and oxygen containing blast. In this view the paper presents the results of the study on the effect of oxygen in the gaseous phase and its addition into the charge of pyrite in the process of arsenopyrite decomposition. Thermodynamic analyses showed that under thermal processing of arsenopyrite in the presence of pyrite and limited quantities of oxygen in the gaseous phase the formation of arsenic sulfides is possible according to the following reactions:

Jan 1, 2003

By Ling-yun Yi, Yuan-bo Zhang, Bing Hu, Zhu-Cheng Huang, Zhen-yuan Liao

"Nucleation and growth mechanism of iron crystal grain in coal-based shaft furnace direct reduction process by microwave heating were investigated by optical microscope, scanning electron microscope and EDX. The results indicate that microwave has selectivity on various minerals which absorb microwaves. The high temperature in certain area of pellets and thermal stress on the interface of minerals are formed, results in the wustite grain smashed along the joints, and iron crystal grains turned out a spherical shape obviously. The iron crystal nucleus is formed firstly at the edge of wustite, on the interface between grains and in the holes in pellets, and grows gradually while reduction carries on from surface layer to inner core. Microwave heating promotes the rate of transportation and accumulation of the iron crystal grain, increases growth rate of iron crystal grain and contributes to formation of dense iron-jointed crystal texture eventually.IntroductionMicrowave energy as a new energy, which selectively heating materials through internal energy dissipation, has the advantages of heating uniformity, high thermal efficiency, fast heating, clean and pollution-free compared to conventional heating motheds. Microwave energy also has obvious superiority in increasing productivity. Thus, it has been widely used in many areas, including electronics, food processing, chemical, medicine, environmental protection, and family life etc [1]. As a rapidly developed green metallurgical method, microwave heating also has been widely recognized by areas of grinding, pretreatment, pre-reduction, drying, furnacing, metal extraction, and waste materials processing and utilization. Some research achievements are gradually putting into practice, showing great potential in chemical and metallurgical industry [2-3]."

Jan 1, 2011

By Osamu Takeda

A decomposition process for PCBs by using basic molten salts as a reaction field was investigated in order to establish a safe, simple and highly efficient decomposition process for polychlorobiphenyls (PCBs). PCB containing chlorine (e.g. 2, 2?, 4, 4?-tetrachlorobiphenyl) dissolved in n-nonane solution was supplied into basic molten salts (NaOH-Na2CO3 or KOH-K2CO3) maintained at 500-700 ?C together with the carrier gas (N2-21% O2) through an injection tube. The injected PCBs in a bubble are decomposed by the reaction with the molten salts and oxygen during rise in the molten salts. The decomposition efficiency of PCBs increased with increasing temperature and was achieved to be higher than 99.995% in a certain condition. From a series of systematic study, the effectiveness of the decomposition process for PCBs by using molten salts was demonstrated.

Jan 1, 2008

By Veena Sahajwalla

The cupola furnace is a coke-fueled shaft furnace used as a primary melting unit in iron foundries. Control of chemical composition of the iron tapped from the cupola is a key factor in productivity and quality control. In an effort to develop a control model for the cupola, a fundamental approach based on physical and chemical principles has been taken to describe the melting process. The behavior of oxidation of the solid charge in the stack of the cupola has been studied. Sulfidation of the charge materials by sulfur-bearing components released to the furnace gases from the coke has been described. Carburization of metal droplets of iron and of steel in separate molten streams has been characterized. Finally, reactions with alloying elements in the hearth (well) of the furnace have been defined. These reactions have been described in a computer-implemented model developed to predict the composition of the iron tapped from the cupola. The model has utilized the thermodynamics and kinetics of the oxidation, sulfidation, and carburization reactions, including temperature and physical aspects, in the various zones of the melting unit. The model predictions have been compared favorably with operating results.

Jan 1, 1992

By Taner Kavas

The refractory bricks of a rotary cement furnace containing of alumina and magnesium chromite were studied in order to determine whether they could be used in the concrete production as aggregates. Three mortars were prepared by mixing 1 part cement, 3 part aggregate materials, 0.5 part water by weight and mechanical, chemical, thermomechanical and microstructural characteristics were evaluated. The compressive and bending strength of samples were determined after 2 and 28 days curing. Resistance to chemicals were established by calculating the weight gain of mortars stored in 2 % HCl solution for 1 h and 24 h. Thermomechanical characteristics were determined by measuring the compressive strength of heat treated specimens at temperatures of 400 °C, 600 °C and 800 °C. Consequently, magnesium chromite containing waste brick aggregates have given the best results.

Jan 1, 2006

By K. V. Sreenivas Rao

Solidification experiments have been conducted to study the effect of interface heat flux and air gap formation on cooling rate of the casting during solidification of Al-4.5wt%Cu alloy. The thermal history of the casting and mold during solidification is recorded using thermocouples connected to computer interfaced data logger. The measured temperatures in the mold are used as input to the IHCP (inverse heat conduction problem) algorithm for simulating multiple heat flux components at the boundary. It is observed that the filling effects induce spatial variation in the thermal field in the mold and casting regions and greatly influence the cooling rate of the casting. The study demonstrates the use of IHCP and in-situ measured thermal profile in analyzing the cooling rate and microstructure.

Jan 1, 2008

By I. Gaballah

The chalcopyrite ore's anodic and cathodic electrodissolution are studied using a Porous Pulsed Percolated Electrode (3PE) reactor. Stationary solid electrode experiments are also performed to explore the mechanism of electrochemical dissolution of chalcopyrite. Experiments with a low - grade natural ore have been carried out at 25 "C in solutions containing 1 M NaCl and 1 M HCl. Galvanostatic and potentiostatic conditions are employed. The influences of current and potential on selectivity of the chalcopyrite ore dissolution are assessed. Anodic oxidation of this ore leads to a preferential dissolution of iron bearing minerals, whereas cathodic reduction is more selective with respect to chalcopyrite. However, in both cases the electrochemical dissolution is incomplete and the current efficiency is low. Design of the actual reactor has to be modified to increase the bed conductivity and to allow continuous experimentations.

Jan 1, 1994

By Joner O. Alves

The disposal of scrap tires has been a serious environmental problem. The treatment of this waste by pyrolysis and combustion has advantages since the landfill space is dwindling and the production of fuel becomes of technological interest. However, that processes needs a rigid control of emissions. This work presents a study of the light hydrocarbon gases (HC) generated during the burn of waste tire chips in a two-stage laminar-flow horizontal furnace. Different temperatures in the primary and secondary stage of the furnace were tested, and the oxygen/nitrogen percentage was also varied during the combustion process. A gas chromatograph was used to identify and quantify the components of the gaseous products of combustion and pyrolysis. The results showed the behavior of the gases during the burn of tires, providing valuable information to the control of hydrocarbon emissions.

Jan 1, 2010

By John W. Lund

The Geo-Heat Center has been investigating the utilization of waste silica from the Cerro Prieto geothermal field for several years. The main objectives of the research were to com-bine silica with various additives to (1) form bricks for low cost housing, and (2) to produce a suitable road surfacing material. The various additives that were tested included hydrated lime, portland cement, plastic fibers, asphalt cement and emulsified asphalt. The silica-cement combination produced the strongest bricks and had the best weather resistance, whereas, the silica-lime combination produced the bricks with the lowest thermal conductivity and specific gravity density. The addition of plastic fibers to the silica-lime mixture improved both strength and weather resistance. The combination of asphalt and silica is not suitable as a road surfacing material, however, silica-cement appears promising.

Jan 1, 2006

By Steve Johnston, Mowafak Al-Jassim, Fei Yan, Omar Sidelkheir, Alain Blosse, Katherine Zaunbrecher

"Imaging techniques are applied to multi-crystalline silicon wafers and solar cells throughout the production process. Photoluminescence imaging, both band-to-band and defect-band, is used to characterize defects and wafer quality at all process steps. These steps include bricks sawn from ingots, wafer sawing, cleaning and texturing, emitter diffusion, edge isolation and glass removal, anti-reflective coating/passivation, and metallization of finished cells. Bricks, wafers, and cells can be imaged at a rate commensurate with in-line measurement, giving spatial information to characterize quality and defect content. Photoluminescence images on silicon bricks can be correlated to lifetime measured by photoconductive decay and could be used for high-resolution characterization of material before wafers are cut. The defect areas in as-cut wafers are compared to imaging results from electroluminescence and lock-in thermography, and cell parameters of near-neighbor finished cells, showing correlations to efficiency, open-circuit voltage, and short-circuit current.IntroductionImaging techniques can rapidly characterize material quality and defect density. Photoluminescence (PL) imaging can be applied to silicon from the brick level to all wafer process steps [1-8]. At the brick level, material thickness allows for measurement and correlation to lifetime where surface recombination effects are minimized [6, 7]. At the as-cut wafer level where thin unpassivated wafers prevent accurate lifetime assessment due to surfaces, defects can still be categorized and quantified to predict finished cell performance [3-5]. Defect regions can be identified by recombination-limited band-to-band PL or by defect-band emission [9-12]."

Jan 1, 2012

By Alex Meystel, Diran Apelian

"In this paper, an outline is given for a theory of intelligent control (IC) of manufacturing processes (MP) based upon what all of them have in common: all MP's can be represented as distributed networks of sequential/parallel elementary ""lumped"" models; all elementary models are organized by definite input-output conditions, and by the set of constraints; all elementary models incorporate not only well defined physical knowledge, but also assumed physical knowledge, expert knowledge, expected knowledge to be obtained during the process from sensors, etc. This creates a hierarchy of elementary controllers coordinated by local coordinators of different levels up to a global coordinator. The latter verifies the adequacy of MP by using a holistic image of the process: depictogram. The structure of knowledge based controller is introduced, and the analytical/linguistic tools of control are presented. The concept entails a number of perspectives which are discussed in the conclusions.1. IntroductionIt is becoming increasingly clear to those of us in Engineering and Technology oriented fields that the so called ""service industries"" do not create wealth. Moreover, it is now accepted that manufacturing is the key to the creation of wealth from a socio-economic point of view. This appreciation of the importance of manufacturing is reflected by the transformations we are seeing in our factories, as well as the changes in both curricula and research activities of our universities. Though we find these changes to be in the right direction, there is yet much more to be done to advance the frontiers of manufacturing and materials processing as we approach the third rnillenium."

Jan 1, 1988

By B. Q. Li, S. P. Song

"This paper describes an on-going research on developing coupled boundary element and finite element algorithms for the solution of thermal and electrodynamic problems relating to materials processing. The coupled methods are uniquely suitable for field problems involving composite regions, in which detailed information on field distributions within one particular region is of more interest and yet the solution can be obtained only if the effects of other regions are all considered. Problems of this type include heat transfer in multiple regions and also magnetic induction involving an infinite boundary. The hybrid boundary and finite element formulation, algorithm development and the applications are discussed. Two examples are given to demonstrate the capability and accuracy of the coupled algorithm for heat transfer problems. Various treatments of corner discontinuity are discussed. It is found that the double flux treatment is an ideal choice amongst those tested as it is easy to implement and also gives the most accurate solution. 1. INTRODUCTIONElectrodynamic and transport problems occur frequently in materials processing systems. Accurate solution of these problems is of great importance not only for our fundamental understanding of physical principles governing these phenomena in the processing systems but also for optimization of the existing processes as well as development of new processes. For this purpose, many numerical algorithms have been developed. These computational schemes in general can be classified into three categories, that is, the finite element and finite difference schemes and the boundary element scheme. The former two are domain based numerical algorithms while the latter the boundary-based algorithm.The finite element method, which is based on the variational calculus, is a very useful and yet popular engineering numerical method for boundary value problems defined over irregular boundaries. The use of the method requires the discretization of the entire domain. It can be applied to solve both linear and nonlinear problems, but is particularly powerful for nonlinear problems that involve the field variables defined within the computational domain. On the other hand, the boundary element method, with its root in the Green's function method, is very efficient for linear boundary value problems or nonlinear problems that involve field variables only along the boundaries. The primary advantage of the boundary element method lies in the fact that only the boundaries of the computational domain need to be discretized, and hence the dimension of the problem is reduced by one, compared with the finite element method."

Jan 1, 1994

By Mark Jolly

"Instead of using the traditional batch casting process, the CRIMSON [1] (Constrained Rapid Induction Melting Single Shot Up-Casting) method employs a high-powered furnace to melt just enough metal to fill a single mould in a closed crucible. The crucible is transferred to a station for computer-controlled counter gravity filling of the mould for optimum filling and solidification. The CRIMSON method therefore holds the liquid aluminium for a minimum of time drastically reducing the energy losses attributed to holding the metal at temperature. With the rapid melting times achieved, of the order of minutes, there isn’t a long time at temperature for hydrogen to be absorbed or for thick layers of oxide to form. The metal is never allowed to fall under gravity and therefore any oxide formed is not entrained within the liquid. Thus higher quality castings are produced leading to a reduction in scrap rate and reduced overall energy losses.IntroductionEngineers at the University of Birmingham, England, with local company, NTec, have invented a new casting process that will reduce the energy costs of light-metal foundries. The technology, entitled CRIMSON, means that foundries need only heat the quantity of metal required to fill a single mould rather than large batches that use unnecessary energy and create waste. The complete concept of CRIMSON requires a change of philosophy in the approach to casting and requires the user to think holistically in order to reap the full benefits from the process. This paper will discuss the various aspects of energy wastage within the foundry sector and discusses the processes whereby the energy can be reduced. Primarily the author focuses on the aluminium sector but CRIMSON can be applied to many of the non-ferrous “light” alloys. Ferrous materials and non-ferrous “heavy” alloys can also benefit from some of the ideas but not necessarily directly from the application of CRIMSON."

Jan 1, 2010

By Stavros A. Argyropoulos, Henry H. Hu

"The assimilation of exothermic additions in liquid metals exhibit an array of unique coupled heat, mass and momentum transport phenomena. These phenomena are further complicated by the presence of a moving boundary.This paper describes a) A mathematical model which simulates the complex phenomena, and b) An extensive verification of the mathematical model. The SIMPLER algorithm was employed to solve numerically the pertinent partial differential equations. The computational results indicated that the exothermic heat of mixing led to a rapid increase in temperature around the moving boundary, which produced an enhanced convective flow in the liquid phase. The intensification of fluid flow around the moving boundary resulted in an acceleration of the melting process.Verification of the model was carried out in two contexts. The first was, in a low temperature physical model consisting of ice immersion in different sulfuric acid solutions. In this physical model, both temperature and velocity measurements were carried out. The model results were compared with experimental measurements and they were found to be in excellent agreement. The second context employed high temperatures, involving the assimilation of silicon in high carbon liquid iron. The model was also applied to predict fluid flow, heat and mass transfer for these high temperature experiments and a good agreement was obtained.In addition new dimensionless heat transfer correlations that quantify these complex phenomena will be presented."

Jan 1, 2001

By T. S. Piwonka

Modeling the solidification of shaped castings has progressed beyond the initial problem of determining the correct heat and fluid flow relationships which describe the solidifying castings. Today the challenge is to describe second order effects which determine the ultimate quality of the casting. The challenges to the modeling community posed by the needs of today's foundries for models that work are discussed, with some examples of current modeling problems.

Jan 1, 1992

By James C. Barker

Recent investigations of a 55-km long trend of intrusive complexes on southern Prince of Wales Island have identified significant resources of Nb, Y, REE. U, Zr, and a host of potential by-product metals. The northwesterly trend comprises multi-phased sodic alkaline and peralkaline diorite, monzonite, syenite, and riebeckite granite. There are at least three significant deposit types recognized, two of which, 1) pegmatite dikes/vein-dikes that zone laterally from the intrusions and 2) concentrically zoned pegmatites, contain most of the lithophile metals. A third, epigenetic replacement-type mineralization, contains much of the U resource. Other deposit types with minor or unknown resource potential include diatremes, carbonatite, and placers. This report summarizes the deposit evaluations, characterizes the mineralization, and estimates the resources. To date a total of 40.7 million tons of mineralized material is estimated as indicated or inferred. Most of the Y203 plus REO is at a grade exceeding 0.5% and half of the Nb20S exceeds 0.125%. Tonnage estimates would likely be substantially lncreased with additional exploration. Mineralogy is generally fine-grained and complex, and consists of more than a dozen principal REE-Y-Nb-U-Th-Zr phases, the sum of which may compose up to half of the rock. Approximately half of the REE-Y content comprises the heavy yttrium subgroup which is uncommon compared to deposits elsewhere. Although the Alaskan deposits are likely subeconomic at today's metal prices and consumption levels. recent technological advances suggest future demand may increase.

Jan 1, 1988

By Jacqueline JAlexander

Two of the most important phenomena which govern the continuous casting process and determine the quality of the product are the fluid flow and the heat transfer. Steel flows into the mold through the ports of a bifurcated submerged entry nozzle (SEN), which directs the jet to the mold narrow faces where the superheat contained is dissipated on the solidifying shell. Many important aspects of the fluid flow in the mold are transient and difficult to control. However, the time-averaged flow pattern in the mold is greatly influenced by the nozzle geometry, the submergence depth and the mold dimensions. The aim of this work is to analyze the relationship between the heat transfer and the fluid flow pattern inside the mold using the CFD technique at several operating conditions.

Jan 1, 2009