Search Documents

By Mark E. Schlesinger

Engineering design follows a six–step sequence. Demonstration of this sequence in materials engineering is less common. A case study is presented, using the 1989 paper by Gafner on the development of 990 gold-titanium alloy. This paper identifies a need, develops the problem, identifies alternatives, demonstrates the use of metallurgical principles to identify alternative responses, and shows how more favorable options are selected. The paper can also be used to illustrate engineering design as an iterative process. The paper is also useful as a starting point for more in-depth examination of specific elements of the design process, and lends itself to the creation of student exercises.

Jan 1, 2014

By Dorothée Proffit

Characterization of solids containing cyanides is carried out according to recommendations and standard guidelines. Most of these procedures are based on the analysis of leachates collected either on site or after leaching in the laboratory of samples. Unfortunately, these sole results are often insufficient to identify the source of the pollution. To provide 'a more complete characterization of polluted solids, optical and electron microscopy, XRD, Mossbauer spectroscopy, and transmission infrared spectroscopy were combined to analyze leachates and raw or ground samples. This combination of techniques allows the determination of the kind of cyanoferrate complexes are present in the solid state, different from insoluble Prussian Blue, since they do not have the same extraction' behavior. The use of all these techniques to characterize solid samples combined ,to the usual analysis of solutions gives a better understanding of ' the cyanide behavior.

Jan 1, 1998

By Stein Tore Johansen

Some ferro-silicon fumaces have heat-recovery equipment. Here, the recovery of electric energy from the off-gases can be increased by increasing the off-gas temperature. This is easily done by reducing the amount of air which usually is mixed into the off-gas to cool the gas mixture. If the off-gas becomes too hot problems with severe fouling or clogging of the gas channels? close to the fumace is observed~ The result is irregular stops to clean the off-gas channels. The paper focuses on the nature? of the clogging phenomena and some of the ways to avoid clogging. A detailed experimental study was carried out at the Elkem Thamshavn Plant. Theoretical studies were performed to understand the particle deposition, turbulent multiphase fluid flow and off gas combustion in the off-gas channels. The study has resulted in reduced clogging.

Jan 1, 1992

By H. -Peter Sattler

The laser sorting technique for replacing the handpicking of the non-ferrous metal scrap from auto shredders was first introduced 1990, The process is based on the use of atomic emission spectroscopy induced by lasers to identify the scrap particles and sort them with adequate systems into main fractions of Al-, Zn-and Cu-alloys, stainless steel and lead, In the meantime the handling technique for the scrap, i.e. the singling and sorting technique as well as the analytical detector were further developed for more efficiency and higher reliability, i,e. less maintenance, minor sorting errors etc. These developments were mainly based, on and initiated by operational experiences from the startup phase of a first production plant. Part of the on going research work was the development of an ,aluminium detector which makes it the first time possible to sort mixed aluminium scrap automatically into specific alloy fractions.

Jan 1, 1995

By A. J. Paul, K. O. Yu

"Today, foundries are moving towards the use of models and design tools to gain a competitive advantage in producing castings of high desired quality. This leads to a growing alliance between foundries, software developers and researchers seeking to model, visualize and understand the phenomena taking place during the casting process. In addition, there is a need to develop affordable techniques to produce parts in small lot sizes. This leads to the development of a Flexible Manufacturing System consisting of: (1) up-front computer-aided engineering; (2) computer integrated proto typing with solid freeform fabrication; and (3) fabrication of the actual mold and related equipment to cast the part.This paper discusses some of the developments that are taking place today in the areas of modeling the physical phenomena during the casting process as well as towards developing a Flexible Manufacturing System for producing cast parts. Areas that require most work involve prediction of defects and mechanical properties using simplified analyses. In addition, electronic data sharing for collaborative engineering between geographically dispersed team members is also discussed. Case studies are presented showing successes as well as failures.IntroductionCasting, one of the oldest forms of metalworking, has recently seen a flurry of developments in the area of solidification modeling. These developments have come about after the realization that, in order to stay competitive, foundries need to reduce their scrap rate and production costs, and increase casting quality. Even though this is not new knowledge for foundry engineers, the tools to help them achieve this goal are just being developed and put in place for use by foundries. Several state-of-the-art software packages are currently available to analyze the solidification behavior in complex shaped castings. These packages make use of several different approaches for solving the various problems associated with casting processes. The overall architecture of a comprehensive solidification modeling system is shown in Figure 1."

Jan 1, 1994

By Moto Goto

Today, Pierce-Smith converters, coupled together with various types of smelting units, are used in most of the world's smelters. However, due to the "batch" processing nature, and problems associated with fugitive emissions during the transfer of melt and blowing stages, this arrangement will unlikely be adopted in future smelters. Modern day alternative processes include the Mitsubishi Process, Outokumpu Flash Smelting and Flash Converting Process, the Noranda Process, and the Ausmelt Process, but only the Mitsubishi Process is a "truly continuous" smelting and converting operation, producing a constant flow of blister without tapping, and is economically proven by long term commercial operations. This paper reviews recent advances in modern continuous converting technologies, with a special section devoted to operation of the "first standalone Mitsubishi C-furnace" coupled together with a Noranda Reactor, at Port Kembla Copper Pty. Ltd. in Australia.

Jan 1, 2003

By James O'Brien, Lyman Frost, S. Elangovan, J. Stephen Herring, Joseph Hartvigsen, Carl Stoots, Anthony Nickens

"Carbon dioxide recovered from concentrated sources, such as metallurgical reduction furnaces, cement kilns and fossil power plants can provide a valuable feedstock for a synthetic fuels industry based on energy from nuclear, solar, wind and hydropower sources. High temperature co-electrolysis of CO2 and steam to produce synthesis gas has been demonstrated using reversible solid oxide fuel cell technology. Where a source of high temperature process heat is available, such as from an advanced high temperature nuclear reactor or solar dish concentrator, the endothermic electrolysis reactions can utilize both thermal and electrical inputs in such a way that the conversion efficiency within the cell is 100%. Synthesis gas produced in a coelectrolysis cell has been further reacted over a catalyst to produce conventional hydrocarbon fuels. Widespread implementation of synfuel production from CO2 will enable a much larger reliance on intermittent renewable energy than can be accommodated by conventional electric demand profiles.IntroductionFor the past several years, Ceramatec, Inc and the Idaho National Laboratory (INL), have been studying the feasibility of high temperature solid oxide electrolysis for large-scale, nuclearpowered hydrogen production under the U.S. DOE’s nuclear hydrogen initiative (NHI) as an alternative to the thermochemical process. Parallel to this effort, the INL and Ceramatec have been researching high temperature co-electrolysis of mixtures of steam and CO2 to produce syngas:"

Jan 1, 2008

By Jian Li

Corrosion resistance of materials is highly dependent on the microstructure of the specific material. Apart from general corrosion rate measurement using techniques like linear polarization and A.C. impedance, microstructural investigations are frequently needed to identify the root cause of corrosion. Advanced techniques, including scanning electron microscopy (SEM) and transmission electron microscopy (TEM), have been well integrated into routine characterization studies. Other microscopy techniques, including electron probe micro-analyzer (EPMA), Auger, X-ray photon spectroscopy (XPS) and secondary ion mass spectroscopy (SIMS), can provide detailed chemistry information on corrosion products. In recent years, focused-ion beam (FIB) microscopes have evolved into an important microstructural characterization instrument. In this study, corrosion of rebar encased in concrete was studied in great detail using advanced microscopy techniques. Corrosion product on the rebar surface was identified as ferrous oxide with relatively large crystal size. The morphology of this passive layer was thoroughly analyzed, and its formation mechanism is proposed.

Jan 1, 2009

By François Larouche

Since their commercialization in the early 1990s, lithium-ion batteries (LIBs) have become ubiquitous for powering a myriad of portable electronics. Their usage now extends to the automotive industry and stationary energy storage market. With an average life of 6.2 years and the strong demand, the volume of spent LIBs has increased exponentially, making recycling mandatory. Currently, recycling/ recovery of spent LIBs is limited in comparison to all other types of batteries. The current processes focus mainly on the recovery of the most valuable metals such as cobalt and nickel, leaving lithium and phosphate in a low value end-product. It is necessary that new advanced recycling technologies are developed for the recovery of spent LIBs both from an economic and environmental perspective. In this paper, the current R&D status of LIBs recycling is reviewed with the emphasis placed on hydrometallurgical processing opportunities for Li-ion and Li-solid state batteries.

By C. J. Newman

The Kidd Creek Copper Smelter has been expanded from its original design of 59,000 tonnes of copper per year to over 120,000 tonnes per year. Modifications to the process gas handling system and acid plant have been made to accommodate this higher production rate and to generally optimize the operation. The gas handling system associated with the continuous smelting process is discussed in terms of boiler accretions and modifications to minimize their impact on operations; design changes to effect reductions in high pressure drop duct configurations; material changes to overcome corrosion and plant additions to improve gas cleaning capability. The acid plant is reviewed with references to changes? made to accommodate the increased SO2 gas strength resulting from the higher smelting rates.

Jan 1, 1992

By R. J. St. Eloi

The Kidd Creek Copper Smelter has been expanded from its original design of 59,000 tonnes of copper per year to over 120,000 tonnes per year .. Modifications to the process gas handling system and acid plant have been made to accommodate this higher production rate and to .generally optimize the operation. The gas handling system associated with the continuous smelting process is discussed in terms of boiler accretions and modifications to minimize their impact on operations; design changes to effect reductions in high pressure drop duct configurations; material changes to overcome corrosion and plant additions to 'improve gas cleaning capability. The acid plant is reviewed with references to changes made to accommodate the increased S02 gas strength resulting from the higher smelting rates;

Jan 1, 1992

By Frank L. Marley

Mexican silver mining operations have existed prior to the sixteenth century. Recovery processes throughout the centuries were developed at the many mining localities and have progressed through smelting, the patio amalgamation process to cyanidation and flotation. A study of the present silver mining zones is reported in which the ores are evaluated in terms of the mineralogical constituents, their state in the matrix and the effects these are noted to impose upon the efficiency of recovery. Silver mineral identifications were by quantitative ore microscopic and scanning electron microscopic energy dispersive X-ray analysis.

Jan 1, 1982

By P. J. Mackey

New and emerging, as well as proven technologies for the smelting of copper, nickel, lead and zinc are briefly reviewed. The number of new technologies available today is greater than at any time in the past, and interest and development activities remain high despite the economic dif-ficulties faced by the non-ferrous metallurgical industry. Part of the impetus is provided by the realization that only the most cost effective producers will remain competitive, and that new technology is one key to cost effectiveness. The commercially proven "new" copper smelting processes can now be considered to be conventional- technology, and are expected to dominate copper smelting for acme time. There is a growing. interest in continuous copper converting, although direct smelting and converting to copper in one vessel remains the- ideal. There is little activity in nickel smelting. After many years. of development, it appears that several new direct lead smelting processes will soon be a commercial reality. The electrolytic zinc process is expected to continue its dominance, although there is a renewed interest in pyrometallurgical approaches. One of the new zinc processes, and a molybdenum smelting process, illustrate the possibilities of using plasma technology in non-ferrous metallurgy. In the area of complex sulphides, there is perhaps less interest in the treatment of bulk con¬centrate, and more in the treatment of so-called dirty copper concentrates. Much of the technology ancillary to smelting has remained relatively unchanged, and more effort must be made to advance the technology in areas such as materials handling, gas cleaning and sulphur fixation, and energy recovery. More attention to engineering design is also needed. Escalating capital costs may make mini-smelters attractive, but imaginative technology and innovative engineering will be required to make them cost effective. Finally, a glimpse is offered of the smelter of the future.

Jan 1, 1983

By Roland Loewen

A review of the aqua regia method for the recovery of gold from jewelry shop wastes is given. Also outlined is a specialized procedure for the recovery of the silver that occurs in these wastes. A classic method for the recovery of platinum and palladium is, given. There is a brief review of other gold and silver refining methods. Environmental conditions are discussed and a few perhaps, new and useful processes ,are mentioned. References are by author or editor and are listed alphabetically. Suggestions for further information in the field of precious metals, are given in a final list.

Jan 1, 1989

By P. Heald-Wetlaufer

Doubly polished sections (i.e., sections polished on both sides) allow insights into complex paragenetic relationships, the interpretation of which is essential to understanding ore-forming processes. Alternate viewing of these optically superior sections in transmitted and. reflected light facilitates the recognition and definition of growth zones in ore and gangue minerals and the interpretation of postdepositional changes, such as hydrothermal leaching and replacement. Many such observations would escape detection by conventional petrographic methods. Our procedure for preparing doubly polished sections has evolved during the past 20 years and incorporates many standard procedures. Studies from such diverse districts as Creede, Colorado, Hokuroku, Japan, and the Upper Mississippi Valley zinc-lead district, southwestern Wisconsin, demonstrate the value of observations from doubly polished sections in constructing genetic models. The advent of doubly polished sections represents a major advance in the study of ore deposits and they should be a standard tool in every ore petrology laboratory.

Jan 1, 1982

By S. S. Chabot, S. E. James

A recent survey of CEOs from major steel companies worldwide revealed the importance of recycling zinc units from EAF dust, mill scale, blast furnace dust, and other zinc containing streams in their plants. Many processes were developed and installed in response to this challenge. The most successful approach involves the production of a crude zinc oxide and selling it to primary zinc producers to recover the metal value. The problem with this process is the high concentration of halides in the crude oxide. This type of material cannot be processed directly in an electrolytic zinc plant because of corrosion problems it will cause in electrolysis. In 1999, BRZ installed a zinc oxide receiving and washing plant to minimize the impact of halides to its circuit. A description of the washing plant and initial operating results are included.

Jan 1, 2000

By C. P. Manning

This paper reports recent progress in the development of a unique metal extraction technology utilizing zirconia-based inert anodes for the electrolytic reduction of metals from their oxides. In this process, the target metal oxide is dissolved in an ionically conducting liquid solvent phase. An extended anode consisting of an oxygen-ion-conducting stabilized zirconia membrane in intimate contact with a catalytically active electronic phase and an inert electronically conducting cathode are inserted into the molten flux containing the oxide. When the appropriate electric potential is applied between the electrodes the target metal is reduced at the cathode and oxygen ions are selectively transported across the stabilized zirconia membrane and oxidized at the anode. When the process is conducted at temperatures between 1200-1400°C, the ohmic resistance drop across the stabilized zirconia membrane is low, and high current densities on the order of I A/cm2 or greater can be obtained. In addition, the process efficiency can be increased further by directly reforming hydrocarbon fuel over the anode. Laboratory experiments at Boston University have demonstrated the technical viability of employing zirconia-based inert anodes for environmentally sound production of metals such as magnesium, tantalum, aluminum, etc., directly from their oxides. Significant progress has been made in the application of this concept to the electrolytic reduction of magnesium at 1300°C. The research topics covered include stability of the zirconia membrane in the selected molten solvent (flux), volatility of the flux, electrochemical characterization of the electrolytic cell, and analysis of the metals produced.

Jan 1, 2003

By Thomas P. Battle

Ilmenite (iron titanate) is the source of over 90% of all the titanium produced in the world today. At some point during production of titanium dioxide or titanium metal the iron impurity must be removed. Too often it becomes a waste instead of a product. DuPont and MINPRO have developed a solid-state process which separates the iron and titanium components of ilmenite into different high-purity powders, which can be separated using conventional mineral processing techniques. The main reactor in this process is a unique high-temperature ball mill, where the iron segregates from the ilmenite lattice with the assistance of catalytic quantities of He\. The results of lab, pilot plant, theoretical, and scale-up studies are presented and discussed.

Jan 1, 1996

By Robert C. Laudon

Spectral reflectance data for 335 minerals, including 228 minimum-maximum combinations for anisotropic minerals giving a total of 563 data sets, have been collected from the literature and combined into a single database. Quantitative color values for x, y, Y, Ad , and Pe referred to ICI standard i11uminant C have been calculated from the spectral reflectance data and are included in the database. The programs plot spectral reflectance curves together with all quantitative color data for each mineral in the database. The plots and data can be directed to a dot-matrix printer such that a databook of quantitative color and spectral reflectance having one mineral per page can be generated for the ore microscopy laboratory. In addition, by sorting the database and grouping the minerals, groups or individual minerals can be plotted on the chromaticity diagram, and this plot can also be sent to a dot-matrix printer. The programs are written in compiled BASICA for an IBM-PC with graphics capabilities and at least 128KB random access memory (RAM). The databases are accessible either through the BASIC programs or through any commercial database system capable of loading and writing to an ASCII format sequential file. The programs and database are available by sending a blank diskette and self addressed, stamped envelope to the authors.

Jan 1, 1987

By Guo Chen, Xuefeng Liao, Tu Hu, Shengzhou Zhang, Hongying Xia, Jinhui Peng, Libo Zhang

Pine nut shell is as raw material for preparation of high surface area activated carbon (HSAAC) by microwave induced KOH activation. The effects of microwave power, activation duration and KOH/C mass rate (R) on the iodine adsorption capability and activated carbon yield were investigated. Additionally the surface characteristics of HSAAC were characterized by nitrogen adsorption isotherms and SEM. The operating variables were optimized utilizing the response surface methodology and were identified microwave power 738W, activation duration 17 min, and R 4, corresponding to a yield of 46.28 % and an iodine number of 2154 mg/g. The key pore structure parameters of HSAAC such as the Brunauer–Emmett–Teller (BET) surface area and total pore volume were estimated to be 3819 m2/g and 2.09 mL/g, respectively. The findings strongly support the feasibility of microwave heating for preparation of HSAAC from spent pine nut shell by microwave induced KOH activation.

Jan 1, 2016