Search Documents

By Wei Lv, Yang Zhou, Qiang Li, Xuling Chen, Zhiyun Ji, Min Gan, Guojing Wang, Xiaohui Fan

Mineralization during sintering is a process to make part of the raw material melt after serial complex chemical reactions at high temperature. However, high temperature mineralization behavior of the adhesion layer and nucleus particles in the granules during the sintering process has been studied. Research findings reveal that solid-phase reactions between iron ores and fluxes in adhesion layer occurred first, of which the product would induct the generation of the initial liquid phase. By the assimilation of the initial liquid phase, fluxes which served as nucleus particles in granules, such as limestone and dolomite, could dissolve in the liquid phase and extend its amount as increasing temperature, whereas iron ore nuclear particles remained as unfused ores for their insufficient mineralization. Therefore, the mineralization proceeding for sintering was achieved: the iron ores in fine fraction (−0.5 mm) reacted with all fractions of fluxes to form the melt zone, while the coarse iron ores (+0.5 mm) acted as unfused ores, which formed the final sinters together with the melt zone.

Mar 1, 2017

By Gábor Csicsovszki

We have developed a novel method - at the laboratory scale - comprising an ion-exchange separation and a membrane-electrolysis step for the purpose of zero-waste regeneration of spent HCl pickling liquors originating from hot-dip galvanizing of common steels. It is aimed at the parallel regeneration of HCl and iron. Experiments revealed that iron can be electrodeposited at high current efficiencies by maintaining the following conditions: 0.04-0.08 M HCl, 500-1000 A/m2, 20°C and stationary electrolyte in a conventional cell. Zinc in the solution did not disturb the deposition of iron, however it contaminated the product and it poisons the anion-exchange membrane required to tackle acidity during electrolysis. For a preliminary separation, anion-exchange tests were carried out to produce pure iron solutions. Beyond the equilibrium studies, column experiments were carried out showing that low flow rates of the loading solution and the ~1.5 M HCl eluent are essential for separation.

Jan 1, 2006

By Richard D. Hagni

Microscopic examination of selected, representative, unweathered samples of Birmingham, Alabama, Silurian, sedimentary iron ores has fully revealed the nature of the phosphorous-bearing mineral grains. The grains are composed of carbonate-fluorapatite (collophane), range in size from 1 um to 2.25 mm, and exhibit varied types of intergrowth with hematite. Modal analyses conducted under cathodolumi-nescence have provided quantitative data on the a3undance of each of 15 types of phosphorous-bearing mineral grains and made it possible to assess the potential phosphorous liberation from four types of iron ore. The results indicate that 27% of the total phosphorous contained in the iron ores in the western part of the Birmingham district can be expected to be liberated by fine grinding; 60% for ores in the eastern part of the district.

Jan 1, 1982

By Chikabumi Yamauchi, Mitsuru Tanahashi, Toshiharu Fujisawa

"Thermodynamic properties of impurities in molten silicon are of prime importance in developing economical production methods of solar grade silicon. In the present research work, thermodynamic properties of boron, the most difficult element to remove from molten silicon, were measured by chemical equilibration techniques at 1723 and 1773 K. Activity coefficients and self-interaction parameters of boron in molten silicon were determined by equilibrating the melt with solid BN under controlled nitrogen partial pressures. Interaction parameters between boron and nitrogen in molten silicon were also determined by equilibrating the molten Si-B alloys with solid Si3N4• Based on the data obtained, the stability diagram of the Si-B-N system was established.IntroductionPhotovoltaic power generation using a silicon solar cell is expected to be the most promising energy source, because it is inexhaustible, cleaner and more safety than conventional energy sources, such as thermal or atomic power generation. At present, expensive off-grade silicon for semiconductor (SEG-Si) is used for a solar cell production. However, if a large-scale photovoltaic energy conversion using silicon solar cell comes into wide use in the near future, silicon will be sure to be in short supply for the cell. Therefore, a development of a new large scale process for solar grade silicon (SOG-Si) production is definitely necessary, which can remove contained impurities from silicon.Among the impurities contained in silicon, boron is one of the most difficult ones to remove by a zone melting or an unidirectional solidification, because its segregation coefficient in silicon is close to unity (0.8). In addition, boron behaves as a p-type silicon semiconductor dopant and, therefore, its content in SOG-Si must be severely controlled. Although some attempts to remove boron by various metallurgical methods have been carried out [I -4], quantitative analysis has not been made due to lack in the information on the thermodynamic properties of boron in molten silicon. From this view point, the activity of boron in molten silicon was determined in the present study by chemical equilibration techniques at 1723 and 1773 K."

Jan 1, 1998

By Tailoka F.

Various metallurgical residues from iron and steel making processes have been treated by chlorination in excess air with hydrogen chloride gas generated from the combustion of scrap polyvinyl chloride (PVC). The residues include dust from both the electric arc and blast &maces, hydrocyclone overflow, zinc - lead blast furnace slags and dust rich in zinc and copper from copper refining. Chlorination is achieved either directly by mixing the residues with scrap PVC or indirectly in a two furnace system. In the latter, scrap PVC is combusted between 523 and 573 K in a horizontal furnace and the resulting gases are then reacted with metallurgical residues in a vertical furnace at 1166 to 1329 K. Gas chromatography, thermogravimetric measurements, XRD and AAS have been utilised to study the reactions. The recovery of non ferrous metals is as high as 80 to 90 % and only a negligible amount of iron is carried over. The optimum temperature for combustion is between 518 and 573 K. Above 600 K, the evolution of HCI is so fast that sufficient chlorination is not achieved. Analysis showed that no dioxins were present in the gases, the residues or the chlorides.

Jan 1, 1997

By Gabriel Plascencia

Copper was oxidized in the temperature range from 300 to 1000 °C under different pressures of oxygen, In the range from 300 to 500 °C, copper oxidizes following the logarithmic rate law; while in the range from 600 to 1000°C oxidation follows the parabolic rate law. Transition from logarithmic to parabolic growth occurs at about 525°C. X-ray diffraction was performed on oxide scales to account for the CuO/Cu2O ratio at different temperatures. Activation energies found in this work are in good agreement with reported values.

Jan 1, 2003

By Gabriel Plascencia

Copper was oxidized in the temperature range from 300 to 1000 GC under different pressures of oxygen. In the range from 300 to 500°C, copper oxidizes following the logarithmic rate law; while in the range from 600 to 1000°C oxidation follows the parabolic rate law. Transition from logarithmic to parabolic growth occurs at about 525°C. X-ray diffraction was performed on oxide scales to account for the CuO/Cu2O ratio at different temperatures. Activation energies found in this work are in good agreement with reported values.

Jan 1, 2003

By Sacha Neven

Submerged lance technologies combine high intensity processing characterized by rapid mixing and reaction rates using a simple reactor design. The Isasmelt technology uses a central submerged lance to inject oxygen-enriched air and fuel into a bath thus creating large gas bubbles and intensive turbulence and splash. The lance is equipped with swirlers to increase gas velocity and heat transfer. This enables the formation of a frozen slag layer on the lance which protects it from the aggressive environment. Water models as well as high temperature reactors were used to validate the Davidson-Schiiler model on bubbling. Frequencies and pressure amplitudes were measured in a wide range of gas flow rates: from m3/sec using a water model to more than 30 m3/sec in an industrial process. Agreement with the model was satisfactory. The experiments however also clearly showed that cross-flow and bubble wake induce slightly higher frequencies. No influence of the use of swirlers on the bubbling frequency was observed in the water models.

Jan 1, 2002

By Pengfu Tan

One copper Isasmelt furnace has been operated in Xstrata Copper at Mount Isa in Australia since 1992. A thermodynamic model and computer program, CuModel, has been developed to model the distribution behaviors of Cu, Fe, S, O, Ni, Co, Sn, Pb, Zn, As, Sb, Bi, Au and Ag, copper loss in the slag, and heat balance in copper smelting process, matte converting process and copper continuous smelting process. The thermodynamic model has been used to model the key parameters in the control of the copper Isasmelt furnace. The effects of the process parameters on the control of the copper Isasmelt furnace have been predicted and discussed. These process parameters include SiO2/Fe, matte grade, coal, temperature, spec air of feed, oxygen enrichment, and MgO contents in slag.

Jan 1, 2006

By R. M. Westcott

A two-electrode, direct current, slag resistance furnace (SRF) has been constructed and operated to selectively reduce the zinc and lead contents of non-ferrous slags. The experimental SRF is equipped with multiple methods of gas/solids injection for both mixing and reaction. A computer is used to position the electrodes and for data acquisition. A geometric factor correlation was previously developed at Columbia University for calculating the electrical resistance on the basis of furnace geometry and slag conductivity. The experimental SRF was used to test this correlation.

Jan 1, 1994

By Keri Ledford, Stephanie Lin, Jason Nadler

Novel processes are being developed to fabricate thin copper thermal wick samples of a targeted porous microstructure. Structures of desired porosity, thisckness and pore size and distribution are achieved by tayloring the incorporation of sacrificial polymer beads in to slurry precursors. The thickness of the final structure is dictated by precisely controllable slurry application methods, such as spin coating. Ina subsequent heat treatment, th epolymer components thermally decompose and the remaining copper particles sinter to form a reticulated foam. The resulting microstructures are characterized in terms of porosity, permeability and specific surface area.

Jan 1, 2012

By J. J. Moore

The application of plasma technology to process metallurgy is briefly discussed. Experiments involving in-flight reduction of minerals (taconite, chromite, in particular) with a solid-based carbon reductant are described. The resultant metallic and slag product analysis is discussed with respect to thermodynamic and kinetic considerations.

Jan 1, 1985

By Ken-ichiro Uemura

"The DIOS process has been developed for eight years since 1988. The research project was started with the element studies carried out by each of the five integrated steel making companies in Japan, the final two and half years were spent for the pilot plant studies. Operation were conducted in the entirely closed and pressurized system successfully as planned. From the result, the DIOS process was proved to be viable as a future iron-making process substitutable for the conventional blast furnace. In addition, a lot of findings were obtained. Hot metal productivity was primarily determined by a oxygen flow rate, and a coal consumption varied depending on the productivity. The post combustion ratio was a little lower than expected from the result of the element study. It was supposed to relate the gas-reforming with coal or volatile matter in the free space of the furnace. Hot metal carbon content seemed to depend on the char content in slag.INTRODUCTIONThe JISF's DIOS pilot plant (DIOS=Direct Iron Ore Smelting Reduction Process) has finished its last campaign of the operations in January 1996. The project was started in 1988 as a joint research of the Center for Coal Utilization, Japan and the Japan Iron and Steel Federation (JISF) with a subsidy for promoting coal productions and utilization technologies from the Agency of National Resources and Energy, the Ministry of International Trade and Industry(MITI). Throughout the pilot plant test, a total of over 20,000 tons of hot metal was produced for more than 2,000 hours of the operation. Recorded production rate was 538 ton/day for 3 days at a specific coal consumption of approx. 1,000kg/hmt. Long-term operation was carried out in the fifth campaign for 18 days, which has proved that the entirely closed and pressurized DIOS process works well as planned. In Figure 1 is shown the representative operational performance obtained in the first five campaigns. The project is going to be finished by the end of March this year after investigating the technical viability and economic potential of the process, and completing the conceptual design of the DIOS commercial plant. In this paper, the system and facilities of the DIOS process are first introduced and some of the results of the pilot plant test are detailed later."

Jan 1, 1996

By Ruiling DU, Xiao YUAN, Keng Wu, Daan XU, Changyao CHAO

To utilize low grade coals to produce high quality semi-coke which can be used in blast furnaces, the pyrolysis of low grade coals was studied in this paper. According to the characteristics of coal pyrolysis process, the temperature range was divided into three parts. The interfacial chemical reaction model, random pore model and the internal diffusion model with the shrinking volume of resultant were established to describe the different ranges of pyrolysis process respectively. The results showed that the experimental data was fitted well, and all the correlation coefficients (r2) exceeded 0.97. Finally, the kinetic parameters for each temperature range have been calculated, which laid a necessary foundation for the simulation and expanded production.

Jan 1, 2016

By R. G. Reddy

Reduction of different chromite ores with carbon was studied as a function of C/FeO ratio and temperature in the range 700 °C to 1100 °C by thermogravimetry (TGA) analysis. Powders of chromite ore(-150 mesh) and carbon(-150 mesh) were thoroughly mixed in a desired proportions and were placed in the reaction crucible. The reduction rates of reactions were determined by continuously monitoring the weight loss as a function of time at constant temperature using TGA set up. The analysis of results suggest that FeO present in the chromite ores is reduced to Fe involving gaseous intermediates CO and CO2. The overall rate of FeO reduction is controlled by the oxidation of carbon. A kinetic equation, that of random nucleation, was proposed. The activation energies for the reduction of FeO, present in Roast Movat and Transvaal ores, with carbon were determined to be 55800 and 23000 J/mole, respectively. The results of the present study are compared with the data available in literature. The low activation energy values as determined in this study suggest that the carbon oxidation reaction is catalyzed. It is concluded from the present investigation that the low grade chromite ores can be significantly upgraded to higher value added chromite that can be used as a feed source for economical smelting.

Jan 1, 1998

By S. K. Shaha, A. Gryguc, S. B. Behravesh, B. Williams, M. Wells, H. Jahed

Warm forging to near final product geometry shows promising benefits in terms of microstructure refinement and texture modification. In the present study, Semi-closed die forging was performed on extruded AZ80 magnesium alloy at a forging temperature of 400 °C and various forging ram speeds. Compression tests were performed to investigate the influence of forging at various deformation rates on the performance of extruded AZ80 magnesium alloy. The microstructural analysis showed that the extruded AZ80 possesses a grain structure typical in wrought magnesium alloys, with sharp basal texture. In contrast, the forged samples had a recrystallized microstructures and a spatially varying textures and crystal orientations resulting from the complex flow behaviour within the closed die forging. Furthermore, once forged, a significant increase in the material isotropy, homogeneity as well as failure elongation were observed. An increase in UCS of 9% was observed in the forging direction, while the UCS in the extrusion direction was similar to that before forging. The changes in UCS can be attributed to both the refined grain microstructure and crystal reorientation. Successful microstructure recrystallization occurs for strain rates which traverse several orders of magnitude, and in general, UCS isotropy increases with increasing strain rate. It is believed that forging cause’s grain refinement and texture modification which act to enhance the mechanical performance (UCS, fracture strain and superficial hardness) for the forging conditions investigated in this study.

Mar 1, 2017

By Zdzislaw Miczkowski

At KGHM Polska Miedz S.A, a direct flash smelting process is used for smelting of chalcocite concentrate for the production of blister copper. The paper presents a model of complex oxidation process of single concentrate grains smelted at KGHM. The description covers main chemical reactions, phenomena of heat and mass exchange inside the grains and between a grain and the surrounding space. In the model, two zones describing the course of process inside the grain were distinguished: ? The first one, which moves faster towards the centre of a grain, both organic and carbonate carbon are freed, The process takes place without the presence of oxygen and results in an increase of the temperature in the core of the particle. ?The second zone moves slower into the grain and the rate of the movement is determined by the presence of oxygen, In that zone the sulphur is eliminated and the oxidation of the organic compounds vapours moving from deeper layers of a grain takes place. Based on the results of laboratory tests, the coefficients that describe the oxygen transportation into the grain and decide the progress in the chemical reaction were determined, The paper contains the results of model calculations for single grains reacting in environment of various content of oxygen as well as the results of model calculations for the laboratory reactor system.

Jan 1, 2003

By Zdzistaw MiGzkowski

At KGHM Polska Miedi S.A. a direct flash smelting process is used for smelting of chalcocite concentrate for the production of blister copper. The paper presents a model of complex oxidation process of single concentrate grains smelted at KGHM. The description covers main chemical reactions, phenomena of heat and mass ex-change inside the grains and between a grain and the surrounding space. In the model, two zones describing the course of process inside the grain were distinguished: ? The first one, which moves faster towards the centre of a grain, both organic and carbonate carbon are freed. The process takes place without the presence of oxygen and results in an increase of the temperature in the core of the particle. ? The second zone moves slower into the grain and the rate of the movement is deter-mined by the presence of oxygen. In that zone the sulphur is eliminated and the oxidation of the organic compounds vapours moving from deeper layers of a grain takes place. Based on the results of laboratory tests, the coefficients that describe the oxygen transportation into the grain and decide the progress in the chemical reaction were determined. The paper contains the results of model calculations for single grains reacting in environment of various content of oxygen as well as the results of model calculations for the laboratory reactor system.

Jan 1, 2003

By Ademar B. Lugão, Sandra R. Scagliusi, Elizabeth C. L. Cardoso

When butyl rubbers are subjected to high energy radiation, they form easy free radicals that initiate various chemical reactions. These reactions alter the molecular distribution of irradiated rubbers by crosslinking or scission affect their physical and mechanical properties. This work aims to the analysis of effect induced by γ-exposure on the crosslinking density in butyl rubbers by swelling measurements accomplished before and after irradiation at 25, 50, 100 and 200 kGy, with further evaluation of crosslinking density accomplished by Flory-Rehner equation; this is a proper procedure for the qualification of radiation resistance. It can be noticed that changes in material structure was due to build-up of new three-dimensional network in studied rubbers. Changes in crosslinking density of butyl rubber compounds emphasize that degradation mechanism is strongly influenced by gamma-radiation doses higher than 50 kGy, since chain scission process predominates over crosslinking reaction.

Mar 1, 2017

By Henrik Gudbrandsen, Geir Martin Haarberg, Ana Maria Martinez, Karen S. Osen, Sverre Rolseth

"The Several approaches were tried for developing an electrochemical route for producing high purity silicon from molten salts. K2SiF6 and metallurgical grade silicon were used as the source of silicon. Molten LiF-KF and pure KF with additions of K2SiF6 were used as electrolytes at temperatures from 550 - 900 oC. Silicon was cathodically deposited and anodically dissolved in the fluoride electrolytes. High electrorefining efficiency was obtained for many elements after electrolysis experiments at constant potential or constant current. The main challenge was to reduce the contents of boron and phosphorus. Another difficulty was to remove inclusions of solidified electrolyte. The lowest energy consumption was estimated to be ~ 3 kWh/kg Si, while the best current efficiency for Si deposition was found to be ~ 95 %.IntroductionSilicon is the most important material for photovoltaic power generation devices because of high feasible efficiency, low ecological impact and slow degradation. Development of a new and less expensive route for producing silicon of the desired quality is necessary in order to make solar cells competitive. Electrochemical routes may be an alternative possibility, and many laboratory studies have been reported over the past few decades. Most of the studies have been performed in molten salts, chloride or fluoride, at moderate temperatures so that solid silicon was deposited at the cathode. The production of high purity silicon has shown an annual increase of about 25 %, due to the increasing demand of solar grade silicon (SoG-Si). For future increased use of solar energy it is important to develop alternative, more energy efficient and cheaper processes for SoG-Si production compared to the Siemens process.Common silicon sources have been SiO2 and K2SiF6 for electrowinning and MG-Si in the case of electrorefining. A serious challenge is to find an oxygen evolving anode for electrolytes containing dissolved oxides. Especially at moderate to high temperatures and in molten fluoride electrolytes this is a difficult task.Many experimental results have been reported in molten chloride electrolytes. Nohira et al. [1-3] and Chen et al. [4] cathodically deposited silicon by electrodeoxidation of solid SiO2 in molten CaCl2 by potentiostatic electrolysis. An alternatice approach is to use electrorefining of low-cost metallurgical grade silicon (MGSi) to produce SOG-Si. In previous studies [5], an MG-Si anode was used, and silicon was successfully electrodeposited on a molybdenum wire in a CaCl2 based melt. It was found that the anode was strongly passivated due to the precipitation of silicon. Also, some deposits detached from the molybdenum wire because of the poor adherence to the cathode.Considering the Cu-Si alloy which has a good segregation effect for some impurities, and should not passivate, could be a good candidate anode for electrorefining. [6]."

Jan 1, 2014