Search Documents

By Christopher B. Vierrether

Reflected light microscopy, scanning electron microscopy, and electron microprobe analysis have been used to determine the mineralogy, phase percentages, grain sizes, textures, and partitioning of cobalt and nickel in two cobalt-nickel rich mattes. These mattes were prepared by submerged bath smelting from a flotation cobalt-nickel concentrate containing 4.8% cobalt and 5.1% nickel. The concentrate was derived from lead-zinc-copper ores of the Viburnum Trend, southeast Missouri. Eleven discrete phases have been distinguished in the matte samples, three of which contain significant cobalt and nickel. The phases are cobaltpentlandite ((Co,Ni,Fe)9S8), cobalt-bearing marmatite ((Co,Fe,Zn)S), shandite (Ni3Pb2S2), bornite (Cu5FeS4), galena (PbS), magnetite (Fe3O4), pyrrhotite ((Co,Ni,Cu,Fe)1_xS), chalcocite (Cu2S), CuPbS phase, metallic copper, and metallic silver. Cobaltpentlandite and cobalt-bearing marmatite- occur in coarse grains (50 µm) that would separate readily during grinding, but shandite contains small (5 - 10um), abundant inclusions of pyrrhotite and bornite.. Some mineralogical variations between the two matte samples were due to differing degrees of oxidation during smelting,

Jan 1, 1988

By Vijaya Thangavelu

Biological leaching of low-grade nickel laterite is based on a non-traditional leaching of oxide minerals using heterotrophic micro-organisms. The organisms solubilise metals by excreting organic acids; these acids then form complexes with heavy metals. High salinity of water supplies and soils in the vicinity of nickel laterite ore bodies is a major abiotic stress to fungi and represents a major challenge in the application of bioleaching process in-situ. Salinity exposes fungi cells to Na+ toxicity and osmotic stress. This study examined the salt tolerance development of Aspergillus foetidus based on gradual acclimatization of organism, its salt threshold and the salinity effect on its metabolism. The biological leaching of weathered saprolite ore with the resulting halotolerant organism under saline conditions was assessed. It was observed that salinity stress affected the organism?s growth and energy utilization

Jan 1, 2006

By R. Angulo

Carbon nanotubes (CNTs) have recently emerged as materials with outstanding properties. This has promoted their consideration as reinforcements for other material systems, such as ceramics. However, one of the fundamental problems with producing CNT-reinforced ceramics is the effective dispersion of CNTs during processing. This has been successfully carried out recently using organic solvents. This paper is a preliminery investigation into the rheological behavior of aqueous CNT-alumina slips, with the objective of moving towards a more environmentally friendly aqueous tape casting process for the production of CNT-ceramic composites.

Jan 1, 2008

By Xuefeng She, Qingguo Xue, Jingsong Wang, Guang Wang

Iron nugget could be got at high temperature using carbon composite pellet, which were made by the mixture of ludwigite and reducing agent. In order to reduce sulfur content in the nugget, effects of additives on the desulfurization was investigated. The sulfur content could be dramatically reduced if the CaO was introduced into the pellet and the sulfur content was as low as 0.046wt.% when the addition amount of CaO was 5wt.%. However, the melting separation of pellet became increasingly difficult and the yield of iron decreased when CaO content in the pellet gradually increased. Na2CO3 could also reduce the sulfur content in the iron nugget and made the iron and slag separate difficultly as well. When 6wt.% Na2CO3 was added into the pellet, the pellet was too difficult to melt separation and the sulfur content in the nugget was 0.084wt.%, which didn’t meet the need of steel making.

Jan 1, 2015

A three?stages countercurrent fluidized bed prototipe reactor to neutralize the SO2from smelter gases has been developed. For gases with 8 vol-%SO2, at 800°C and for 4 h mean reaction time of the limestone, the capture of SO2 is 99%, with off gases with 0.07 vol-%. For 2 vol-%SO2, the total capture of SO2 can be obtained at 750°C and 4 h reaction time. The calcine obtained contain a blend of unreacted limestone and calcium sulphatewith minor amounts of residual lime.

Jan 1, 2006

By Luben Savov

This paper presents recent research works on the removal of the tramp elements Cu, Sn, Zn and Pb from steel. The evaporation of Cu and Sn in iron-based melts treated at reduced pressure of the gas phase was studied in a vacuum induction melting furnace. The effect of chamber pressure, temperature and melt composition was investigated. Since the main source of contamination of steel with Sn and Zn is the recycling of tinplate and zinc coated steel, respectively, possibilities for the removal of meta1ic coatings in a scrap pre-treatment stage were studied, too. Tin was removed in the temperature range 400-5S0°C by treatment with reactive gases featuring high sulphur potential. Zinc can be removed by evaporation or by a combination of thermal and mechanical treatment. The paper discusses the thermodynamics of Pb in carbon-saturated iron melts, too.

Jan 1, 2001

By J. S. Pitsillos

A new furnace tapping technique involving the simulation of a control valve at the exit to a furnace is being investigated. The purpose of this new tapping technique is to regulate the flowrate of liquid furnace products( slags, metals and mattes). Numerical modelling and experimental work has been carried out on tapping of slags leaving a SIROSMELT reactor and the results found to be in good agreement. Numerical modelling has also enabled prediction of the important industrial conditions for the onset of blockage from the shape of the pressure versus flowrate curves. Slag launder experiments have been carried out and a one-dimensional heat transfer model was used to evaluate the effectiveness of launder covers and different coolants. From the experimental results and mathematical model some launder design guidelines such as inclination angle, covers and coolants have been developed.

Jan 1, 1991

By R. M. Cunningham

Asarco operates one of the largest individual copper electrolytic refineries in the world at Amarillo, Texas. The feed for this refinery is a mixture of anodes produced at Asarco smelters and copper purchased t?om a number of primary and secondary sources. The variation in feed makes it imperative that the refinery practices state-of-the-art quality control to minimize the effects'of unwanted impurities in the electrolytic refining process. In late 1993, a plant designed to sigru6cantly reduce the antimony and bismuth levels in the electrolyte was commissioned. The purification plant uses ion exchange technology in conjunction with a novel strippiing system developed by Zeneca Specialties (U.K.). The strippiing system permits the recycling of the eluant and thus avoids the extremely high costs of stripping with conventional reagents. In addition, the environmental impact of treating the eluant for recovery of antimony and bismuth is minimized. This paper outlines the development of the technology and, in particular, describes the operational practices and improvements at Amarillo since the commissioning of the plant.

Jan 1, 1997

By Bowen Li

Andalusite is an excellent raw material for refractory applications due to its high aluminum oxide content and phase transformation to mullite at high temperature. Granular andalusite in particle sizes of about 1 to 2 mm was traditionally utilized for the manufacturing of refractory brick. However, if powder andalusite in micron particle size is utilized in high-alumina refractory products, reinforcement on the refractory brick can be obtained and the sintering temperature can be decreased. The phase transformation of powder andalusite plays a key role for the difference.

Jan 1, 2006

By Yan Fu, Chuanlin Fan, Xiujing Zhai, Yongfeng Chang, Binchuan Li

"The mechanism of the selective chlorination of nickel and cobalt in reduced limonitic laterite was investigated. Reduced ores were obtained from the reduction roasting of a limonitic nickel laterite. The thermal decomposition of related chlorides and the selective chlorination of the reduced ore were carefully studied using Differential Thermal analysis - Thermogravimetry (DTA-TG), X-Ray Diffraction and chemical leaching methods. In the temperature range of 300 - 500 °C, aluminum chloride hexahydrate was chosen as chloride agent. During the selective chlorination, reduced ore was partly chlorinated by hydrogen chloride generated from the thermal decomposition of chloride agent. Then the oxydrolysis of ferrous chloride re-generated hydrogen chloride was used to further the chlorination. Finally, iron was mostly rejected as hematite, while nickel and cobalt were selectively chlorinated. More than 91 %Ni , 90%Co and about 4%Fe in the chlorinated ore was extracted using a water leaching method.IntroductionLimonitic nickel laterite is an important nickel reserve, which is rich in iron in the form of goethite and has low contents of magnesium, aluminum, silicon, and other elements. Goethite is the main nickel-bearing mineral in the laterite [1]. Nickel is generally present in goethite in three modes: (a) associated with amorphous or poorly crystalline goethite, (b) weakly adsorbed to the crystalline goethite surface, and ( c) as lattice substituents [2]. In addition, cobalt in limonite was found to be associated with a manganese phase rich also in nickel [3]. These results indicate that the extractions of nickel and cobalt are highly dependent upon the degree of the decomposition of the nickel, cobalt-bearing minerals.For the selective extraction of nickel and cobalt from limonitic laterite, the ore is usually processed by hydrometallurgical methods, including high pressure acid leaching (HPAL) [4] or reductive roasting - ammonia leaching (Caron process). However, there are still some disadvantages in these processes, such as the expense of autoclaves and scaling problems in HP AL [ 4, 5], and relatively low overall metal recovery, large energy and reagent requirements for the Caron process."

Jan 1, 2011

By Pengfu Tan

Lead blast-furnace bullion cools to near its freezing point in an operation known as copper drossing or hot drossing usually contains 0.02-0.06% copper. The removal of this copper is usually carried out in a batch operation known as sulfur drossing. Sulfur is stirred into the bullion at temperatures near its freezing point, and the dross of copper and lead sulfides that floats to the surface is skimmed off manually. A thermodynamic model has been developed to simulate the copper drossing. The phase diagram of Pb-Cu-S system has been calculated, and the effects of the process parameters, such as temperature, copper content, and sulfur content, on the drossing process have been simulated and discussed.

Jan 1, 2006

By M. Rubinstein, N. C. Koon, B. N. Das, V. G. Harris

"Copper and gold - based alloys having giant magnetoresistance properties were produced by melt spinning from arc melted and cast rods. The ribbon width varied between 1 and 2 mm and the ribbon thicknesses were in the range of 30 to 50 11m. The uniform microstructure of the cast rods indicated the composition homogeneity in the starting material. The ribbons showed composition uniformity across the cross section from EDX analysis. However, the spun ribbon microstructure changed from a 'frozen in' region near the wheel side to a nanosize spherically precipitated phase towards the freely frozen surface. The evolution of the microstructure from the spun ribbon state to the annealed ones was studied by optical microscopy, SEM and TEM. The structural information of the spun and annealed specimens was obtained from X - ray, electron diffraction, electron microscopy and ferromagnetic resonance. Magnetoresistance was measured by the four point probe method.IntroductionRecently. Giant Magnetoresistance. GMR. has been observed in sputtered thin films alloys of Ag. Au and Cu with Co and Fe [1. 2. 3]. The sputtered films are produced by condensation of the alloys from the vapor phase. These Ag. Au and Cu alloys are miscible and homogeneous in the vapor and liquid phase (except Ag alloys which exhibit phase separation even in the liquid phase) but immiscible and heterogeneous in the solid phase. In our work we have produced thin ribbons of the Cu and Au alloys about 30 µm thick from the miscible state in liquid phase by rapid solidification melt spinning. The microstructural development of the ribbons was investigated in the as - spun condition and on annealing. The other properties such as magnetization. GMR and Mossbauer Spectroscopy were also investigated in the various microstructural conditions of the ribbons."

Jan 1, 1994

By James C. Barker

Near Rainbow Mountain in the east-central Alaska Range an ultramafic complex forms a sill-like intrusion composed of dismembered bodies exposed along the south side of the Denali Fault and Broxson Gulch Thrust. The complex comprises dunite and peridotite with lesser gabbro, which together exhibit poorly defined, steeply-dipping compositional layering. The complex hosts four types of copper-nickel occurrences which have characteristic platinum-group elements (PGE), gold, and cobalt distributions. Three of the occurrence-types are considered to have formed as a result of primary mineral segregations which developed during intrusion of the complex. The fourth type of copper-nickel occurrence formed as a result of post-magmatic hydrothermal fluids at intrusive contacts. Scanning electron microscope examination indicates that PGE occur as micron-size telluride and arsenide minerals.

Jan 1, 1987

By Ajit Kumar Jaiswal

"Electric Arc Furnace (EAF) being a power-intensive equipment, EAF based industries are highly dependent on scarce electric energy. This is the reason Government of India is highly concerned about this and laid emphasis on the conservation of electric energy.This paper highlights factors contributing to reduction in specific electric energy consumption in EAF and suggests measures not only for power saving, but also for productivity improvement. To name a few, these are proper sealing of furnace, introduction of oxy-fuel burners, foamy slag practice, increased usage of hot metal/DRI, post-combustion of CO gas for preheating of scrap, improved selection & design criteria of electrics, power demand management, and process automation. Few cases also have been cited, where the above measures have helped in reaping significant benefits.IntroductionFor a long time, Government of India had focused on increase in energy supply, in particular, through electricity generation. Now the emphasis of Government of India has shifted from electricity generation to its conservation for following two reasons:??Power plants have become very cost-intensive??By saving energy, more of it can be delivered at lower cost to the consumersPower generating units, transmission & distribution agencies as well as consumers all have roles to play in the area of energy conservation. By energy conservation, we mean curtailing energy requirement by reducing energy wastages and taking up measures to improve energy efficiency of electric equipment/appliances. In almost all cases, this would be economically beneficial.India’s cost-effective energy conservation potential has been estimated by the Planning Commission at 23 per cent of total commercial energy generated ?1?. A national movement for energy conservation can significantly reduce the need for fresh investment in energy supply systems in coming years. It is imperative that we make all-out effort to realize this potential. Whether a household or a factory, a small shop or a large commercial building, a farmer or an office worker, every user can and must make this effort for his own benefit and for the nation’s benefit as well."

Jan 1, 2009

By Duclerc Fernandes Parra, Vijaya Kumar Rangari, Washington Luiz Oliani, Ademar Benevolo Lugao, Nilton Lincopan

Due to its versatility and low cost, polypropylene (PP) is one of the most widely used polymers in the world, consequently in research and development of new products. The polypropylene modified was prepared by gamma irradiation in acetylene at 12.5 kGy dose, technical polymer also known as high-melt-strength-polypropylene (HMSPP). It was mixed with montmorillonite (MMT) clay and silver nanoparticles (AgNPs) for bactericide activity. HMS-Polypropylene-clay-silver nanocomposites were manufactured using twin-screw extruders. Those materials were prepared by a melt mixing process via twin screw extrusion with a wide range of processing conditions. The polypropylene nanocomposites (PPNC) surfaces were exposed to gamma-radiation (60Co) source in presence of nitrogen as inert atmosphere at 1; 3; 5; 10; 20 and 50 kGy doses for modified the surfaces in order to enhance biocide activity. The samples surfaces were characterized by Differential Scanning Calorimetry (DSC), X-ray Diffraction (XRD), Thermogravimetric Analysis (TGA), Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDX) and evaluated by determination of bactericide effects. The results indicate the formation of structures predominantly intercalated of HMSPP nanocomposite. Contact tests for antibacterial activity of the hybrid polymer were applied against Escherichia coli (Gram-negative) and Staphylococcus aureus (Gram-positive) bacteria. The irradiations on the samples surfaces were insufficient to promote activity on contact biocide tests.

Mar 1, 2018

By Stephanie Trant

Montana Tech has been engaged in fundamental research on the processing of critical materials for more than a decade. Efforts include examining novel reagents for the flotation of Rare Earth Minerals (REMs). For this paper, research results on a collector, salicyl hydroxamic acid (SHA), are presented. Various REMs were examined and include the rare earth oxides (REOs), carbonates (RECs), and phosphates (REPs) of a suite of Rare Earth Elements (REEs). Differences are attributed to solution and surface chemistry, coordination number, and ionic diameter. SHA adsorption follows an ion-exchange process that leads to chemisorbed and surface-precipitated states, depending mostly on pH. Many effects are directly attributed to lanthanide contraction. Results should also be applicable to other REM/collector systems and further suggest that REM flotation should consider dual collectors.

By Katsutoshi Komeya

Aluminum nitride(A1N) is a theoretically high thermal conductive ceramic, but is a poor sinterable one because of its covalent bond structure. The densification of A1N had to be done first. It was found in 1968 that rare earth compounds as yttria were an excellent sintering aids. Recently more improvement of conductivity was attained by following effects of yttria: (1) trapping of oxygen in A1N sources to form yttrium aluminates, (2)elimination of the aluminates by heating in carbo-reductive atmosphere. Consequently very high thermal conductivity of up to 270W/mK has been developed. Thus A1N applications for substrates and packages have been opened.

Jan 1, 1992

By Hyun Soo Kim, Joon Soo Kim, Myong Jun Kim, Jyothi Rajesh Kumar, Jin-Young Lee

Rare earth materials have an ever growing variety of applications in the modern and hitech technology. They apply to many an industry with crucial materials and they provide numerous a customers with benefits. Rare earth materials utilization increasing day-by-day in the worldwide, at the same time the resources is very limited in many countries like Korea. The present general article divided four sorts such as 1) mineral processing of Korean ore deals the gravity, magnetic separation and froth flotation, 2) decomposition and leaching of concentrates included sodium hydroxide fritting, sodium hydroxide hot digestion, hydrochloric acid leaching, 3) separation and purification of rare earth elements in mixed rare earth chloride solution consists reduction and oxidation method, solvent extraction, 4) preparation of rare earth oxide compound from purified elemental rare earth chloride solution having oxalate salt precipitation by reaction crystallization. The last part consists of a summary of the present study.

Jan 1, 2015

By Mark Cross, Andrew P. Campbell, Koulis A. Pericleous

"Computational Fluid Dynamics (CFD) modelling is being used to simulate the freeze layers formed within direct smelting processes. There has been some concern whether water-cooled elements can withstand the p~ocess conditions and in particular abnormal cases where they may be splashed in molten metal.To validate the models being developed, two cases from literature have been modelled for solidification and stress analysis. The solidification case is presented in detail and is for hot molten metal flowing through a cylindrical pipe. The walls are at a temperature below the melting point for the metal. The resulting solid (or freeze) layer is within 3% of the value calculated by Sampson & Gibson9 •Preliminary modelling of the refractory-slag interactions is presented. Although three basic mechanisms: Penetration; Corrosion; and Erosion will eventually be modelled, only the penetration is considered here. The corrosion mechanism is to be modelled by tracking the time that the penetrated refractory is at the required temperature.Future work, after adding all the required physics, will focus on the modelling of a water-cooled element placed lower in the smelter. Process perturbations will be simulated to examine what these elements will withstand."

Jan 1, 2001

By Jian Yang

The mechanism of resulfurization in the desulfurization process with magnesium vapor produced in situ by aluminothermic reduction of magnesium oxide was clarified in the present work. The influences of various operating parameters on the resulfurization were studied and the methods that could prevent resulfurization were proposed. There are two kinds of mechanisms of resulfurization in the desulfurization process with magnesium. One is decomposition of the desulfurization product of MgS under the inert atmosphere. The other is oxidation of MgS under the oxidative atmosphere. Under the present experimental conditions, lowering operating temperature and oxygen partial pressure in the atmosphere could effectively prevent the resulfurization. Adding CaO onto the melt surface was an effective method for preventing the resulfurization due to transformation of the desulfurization product of MgS into the more stable compound of CaS. Since addition of the activated charcoal powders greatly decreased the transfer rate of oxygen in the atmosphere to the melt surface, it also reduced the resulfurization remarkably.

Jan 1, 2006