Search Documents

By Mitsutaka Hino

The contents of gangue minerals, such as Al2O3. P2O5, crystalline water and so forth in the iron ore imported to Japan tend to increase year by year. Though the increments of such gangue contents arc approximately 0.1-0.2 mass%, some problems for the blast furnace operation in ironmaking process have already been reported, In order to clarify the mechanism of harmful effect caused by the small increment of gangue minerals, mainly Al2O3. on the blast furnace operation, the dripping behavior of Fe,O-CaO-SiO2-Al2O3-MgO slag from the iron funnel, which simulated the micro-porosity in sinter ore, has been observed with the wide range of basicity, Al2O3, Fe2O and MgO contents. The effect of MgO on the dripping behavior of slag has been summarized in this paper. It was found that the addition of 2mass% MgO resulted in large increase of hold-up on the most of the conditions. When Fe2O content was less than 20mass% and the basicity was lower than 0.8, MgO lowered the hold-up even if the slag contained 10mass% Ah03. Every slag hold-up showed the minimum at the basicity of less than unity on the conditions of constant Fe2O and Al2O3 contents, This trend became remarkable when the slag contained 2 mass% MgO.

Jan 1, 2003

By Vinay Kumar, Manis Kumar Jha, J. Rajesh Kumar, Archana Kumari, Rekha Panda, Jin Young Lee

Rare earth metals (REMs) play a significant role in the manufacture of permanent magnets, fluorescent lamps, catalysts, medicines, super alloys etc. Recently, China, which controls 97% of world trade in REMs, imposed restriction on its export. Consequently, the global demand of REMs is escalating and is expected to exceed the supply by 40,000 tonnes annually. Present review paper reports the flow-sheets of commercial processes based on pyro-hydro and hybrid techniques as well as systematic research for process development to recover REMs from primary and secondary resources. This review paper also reports the recommendation and future prospective to fulfill its demand and supply gap keeping in view environmental prospective.

Jan 1, 2014

By Fuqiang Zheng, Yufeng Guo, Guanzhou Qiu, Tao Jiang, Xiaoming Qu

MxTi3-xO5 is the main titanium-bearing mineral in the titanium-bearing electric furnace slag (TEFS), which is produced by direct reduction-electric furnace smelting process with vanadium titanomagnetite concentrate in Panzhihua-Xichang region of China. In order to effectively utilize the titanium resource in TEFS, the thermomechanical analysis and conditions for the growing up of MxTi3-xO5 grain were investigated, which emphasized on the effects of CaF2 and cooling rate on the crystallization of MxTi3-xO5 in the melting process. The mineral phase and morphology of titanium-bearing slag were determined by XRD and electron microscope technique, respectively. The results indicated that the average grain size of MxTi3-xO5 grown up from 30 to 92 lm and the area fraction of MxTi3-xO5 reached about 66% from 61% under the conditions of 5 wt% CaF2 and cooling rate at 1 °C/min.

Mar 1, 2017

By D. Pradhan, R. G. Reddy

"Electrorefining of aluminum scrap was investigated from AlCl3 –1-Ethyl-3-methyl-imidazolium chloride (EMIC) (Molar ratio 1.65) chloroaluminate electrolyte using copper cathodes at temperature of 90±3°C and cell voltage of 1.5 V. The deposits were characterized using scanning electron microscope (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD). The study was focused to determine the effect of electrode surface modification as well as deposition time on dendritic depositions of aluminum. Their effect on current density was investigated also. It was shown that the surface modification of electrodes reduced the dendritic depositions of aluminum. Pure aluminum (>99%) was deposited for all experiments with the current efficiency of 94-97%. The use of ionic liquids not only reduced the energy consumption but also minimized pollutant emissions (CO, CO2 etc.) compared to the commercial high temperature aluminum production.1. IntroductionAluminum electrorefining/recycling from aluminum scrap using ionic liquid electrolyte is an attractive process today because of the unique chemical and physical properties such as wide temperature range for the liquid phase, high thermal stability, negligible vapor pressure, low melting point and wide electrochemical window. But in conventional practice, melting of aluminum scrap and high temperature molten salt electrolysis makes this process more expensive and less energy intensive (average 13 kWh/ kilogram of aluminum) [1] . Although recycling scrap aluminum requires only 5% of the energy used to make new aluminum [1-2], but the green house emissions like CO2, CO and HF have to be counted for environmental reason. Approximately, 5.31 kilogram of CO2 emitted per kilogram of aluminum production in most of the US industries."

Jan 1, 2009

By J. M. D. Wilson

An analytical program using a combination of SEM-based image analysis techniques is developed for automated modal analysis of ores containing silicate and other gangue minerals. Previous knowledge, gathered by means of either optical microscopy, X-ray diffraction, SEM, or electron microprobe analysis is used to establish discrimination criteria in the image analysis program. The program initially discriminates minerals on the basis of their relative grey values in a backscattered electron image. For those minerals which have overlapping grey levels the minerals are identified by the program using energy dispersive X-ray spectrometry with X-ray counting for twelve or more elements. This technique is useful to quantify ores in which the gangue minerals are numerous. Two cases of application are presented.

Jan 1, 1999

By Toshihide Takenaka

The management of radioactivated stainless steel from a terminated nuclear reactor will become an important subject in the near future. The separation of the elements in stainless steel should be effective to reduce the management labor. In this study, the separation of the elements in stainless steel by an electrorefining tcchnique was investigated in an aqueous solution. The electrochemical reactions of the elements in stainless steel werc studied by voltammetry and potentio-static electrolysis was carried out. A stainless steel anode was dissolved electro-chcmically with good anodic current etliciency in a chloride solution. The residue, where Ni was concentrated, was found on the anode after electrolysis. The electrodeposit in a stainless steel cathode consisted mainly of Fe and Cr and the Ni content in it was less than 0.5wt% under suitable condition. It is concluded that an electrorefining technique is effective for the separation of the elements in stainless steel.

Jan 1, 2003

By S. Pirzada, P. R. Taylor

A reactor was designed and constructed to perform experiments on the generation of value added products using a plasma heat source. The engineering drawings were developed to include multiple sample ports for temperature and velocity measurements and view ports were designed to allow the Physics group to make optical measurements. Two methods for feeding solids into the system were developed and installed. Preliminary experiments were performed to characterize the system at various flow rates and power settings. Experiments were performed using zinc metal and oxygen to form zinc oxide. The particles that were generated were characterized chemically using atomic absorption and x-ray diffraction; and physically using scanning electron microscopy. The particles appear to be of value added size; but there is a tendency for the fine particles to adhere to one another forming agglomerates. Additional experimental work will continue the evaluation of the major parameters.

Jan 1, 1988

By K. Morsi, P. Mehra

"Spark plasma sintering has gained a considerable amount of attention over the past decade, due to its rapid sintering rates, and low temperature requirements, but has so far been usually limited to the production of simple geometries. The present paper examines the current-activated production of extended geometries through the process of spark plasma ""extrusion"". Of interest in the present study is exploratory research into the effect of electrical current activation on the reactive consolidation of powder systems to form intermetallic materials.IntroductionSpark Plasma Sintering (SPS) has been the subject of intense research over the past decade [ 1,2, 3,4,5,6]. The process boasts unique advantages which include ultra fast heating rates, shorter sintering times and lower sintering temperatures than needed in conventional sintering. The process is however limited to the generation of predominantly simple geometries. Recently one of the authors investigated the spark plasma extrusion of aluminum, where an aluminum powder compact is directly (Joule) heated through an applied DC electric current. Here extended geometries can be generated under the influence of electric current. A number of heating sources were identified including the heat source from current, i.e. Joule heating, frictional heating and heat from the deformation energy. However in the case of reactive powder systems, an extra ""one-time"" transient heating source can be supplied. By considering combustion synthesis of powders, this heating source is derived from the reaction between elemental powders to exothermically form a product at some ignition temperature [7]. This exothermic energy heats the compact to the maximum ""combustion temperature'', which could be hundreds of degrees higher than the ignition temperature. Hence a high temperature processing window (of short duration due to heat losses to the surroundings) becomes available in which the material is most suitable for stress-induced deformation and consolidation. For reactive spark plasma extrusion, two scenarios can be envisioned. The first is where the reactive powder compact is ignited through the application of current, and extruded within the high temperature processing window (also under the influence of current). The second scenario is to allow the heat of deformation/friction to heat the material during extrusion, to simultaneously force a reaction and consolidation. Here it is expected that the processing window will be very small if feasible."

Jan 1, 2011

By Lingzhi Yang, Feng Chen, Yufeng Guo, Tao Jiang, Zeqiang Xie

Zinc ferrite (ZnFe2O4), one of the major forms of zinc in Electric Arc Furnace (EAF) dust and zinc leaching residue, is very difficult to chemically dissolve in either acidic or alkaline solutions. In spite of the zinc resources in the Electric Arc Furnace (EAF) dust and zinc leaching residue are abundant, there is no mature utilization technology. This situation not only causes the waste of resources, but also produces the harm to the environment. In the paper, the basic principle of this process has been established by revealing the phase equilibria in the CaO–Fe2O3–ZnO system, where Ca2Fe2O5 can be in equilibrium with ZnO rather than ZnFe2O4 at higher CaO region. It has also been demonstrated that the formed ZnO can be solved by ammonia-leaching and Ca2Fe2O5 keep in solid residue, which can be used as a flux for steel refining.

Mar 1, 2017

By Raj P. Singh Gaur

Due to high concentration of NaOH in the digested slurry after scheelite digestion, it is diluted to about 4N before filtration to separate sodium tungstate solution from the sludge (residue). However, in practice there may be deviations in the normality of NaOH present in the slurry. There may also be variations in the temperature of the slurry and filtration time. Slight variations in these parameters could cause tungsten losses in the sludge via the back reaction: Ca(OH)2 + Na2WO4? CaWO4 + 2NaOH This paper pertains to the effect of normality, temperature and time on the tungsten losses in the sludge that is separated from ?diluted-scheelite-slurry-in-NaOH? via filtration. Results indicated that tungsten losses in the filtered residue (sludge) were quite significant when the slurry temperature was kept at 70°C or higher. The effect of high temperature was less significant at the slurry normality of 3.6 or higher. Combination of low slurry normality (<3.6) and high temperature (>60°C) resulted into large W-losses in the sludge.

Jan 1, 2006

By Ting Liu, Qian Li, Peng Deng

The wastewater containing Hg2+ and Pb2+ does great harm to the environment and human bodies. Traditional wastewater treatment cannot fundamentally put a stop to heavy metals pollution for producing secondary pollution. In this paper, Hg2+ and Pb2+ in wastewater were removed and recovered by sulfide precipitation- flotation. Sodium sulfide was used as precipitant and butyl ammonium aerofloat was used as collector. Results indicated that Hg2+ and Pb2+ could be reduce to less than 0.03mg/L and 0.16mg/L respectively by both coprecipitation- floatation and fractional precipitation- floatation. In these two methods, fractional precipitation flotation could not only remove Hg2+ and Pb2+ from wastewater, but also could recover mercury and lead effectively. The infrared spectrograms showed that the adsorption between butyl ammonium aerofloat and mercury precipitate or lead precipitate is chemisorption.

Jan 1, 2015

By Claudio Toro, Alex Moyano, Jonkion Font, Carlos Caballero, Pedro Morales

"Codelco-Chile in the last decade has carried out industrially-oriented research as an alternative to the traditional batch-type converting process. In a first stage carried out preliminary evaluations in a rearranged Peirce Smith (PS) converter, and then an exploratory test in a “Convertidor Teniente” (Teniente converter, TC) for the Codelco-Chile Continuous Converting Process. However, the validation test for this process in the TC was delayed up to the second quarter of 2007 where the validation studies were done satisfactorily.Thus, the objective of this paper is to present the results of the campaign tests validating the Codelco-Chile Continuous Converting Process in the TC1 of the Codelco Norte smelter.The results of charging the solid or liquid matte or high grade matte (“white metal”) by Garrgun, or by mouth of the 22 m x 5 m TC1 are presented. Some features of the industrially validated process are discussed, and the pilot test results of the matte injection are also presented."

Jan 1, 2009

By Marcos V. F. Fonseca, Gilson V. Fernandes, Caroline G. de Oliveira, Sergio N. Monteiro, Frederico M. Margem, Anna C. C. Neves

Natural fibers represent an economic and environmental motivation for replacing the synthetic fibers, mainly as composite reinforcement material, which is one of their major applications. Some advantages of the natural fibers are the biodegradability, low cost and renewability. Among the natural fibers, the lignocellulosic ones are highlighted for their high resistance. One of the most cultivated lignocellulosic fibers in Brazil is the Eucalyptus fiber, extracted from the bark of Eucalyptus citriodora plant. In this work, it was investigated the tensile behavior of the epoxy matrix composites reinforced with different volume fractions of Eucalyptus fibers. The specimens were made by pouring the still liquid resin into the mold and laying the fibers onto the resin. The results show a decrease in the tensile resistance with the increase of volume fraction. It is due to the low adhesion between the fibers and the matrix.

Mar 1, 2017

By F. Tailoka

Microporous membranes have been used to create a very fine dispersion of bubbles which greatly enhances the mass transfer of electroactive species to the electrode. Using this system, it has been shown that it is possible to electrowin copper as a coherent planar deposit, at high current densities, from copper chloride solutions.

Jan 1, 1990

By Srinath Viswanathan, Zhijing Zhang, Ramana G. Reddy

"The viscosity measurements were carried out on melts of 380 aluminum alloy containing 20 volume % SiC particulates under various shear rates at different temperatures using a Brookfield viscometer. Results showed that viscosities of the melts increased with decreasing temperature and decreased with increasing shear rate. These results were compared with those of 356 alloy and it was found that the temperature had a more significant effect on viscosity of 356 alloy than that of 380 alloy containing SiC particulates. Based on the present experimental data an empirical viscosity model, which considers the effects of both solid fractions in the melt and shear rate, is proposed.IntroductionDiscontinuously reinforced metal matrix composites materials (MMCs) such as aluminum alloy containing SiC particulates have considerable potential for applications in the automotive industry because of their superior stiffness, higher specific mechanical properties, better dimensional stability and strength retention at elevated temperatures when compared to their monolithic counterparts. They have a great advantage in the specificity of their properties, meaning that specific materials can be engineered for specific applications. With such freedom of design, materials engineers have to accumulate a very large database of mechanical properties. Among these properties, the viscosity of alloy slurries is very important for producing, casting and forming process of metal matrix composites materials because viscosity has a decisive influence on fluid flow. The understanding of the rheological behavior of alloy slurries is necessary for these materials to become economic reality. Therefore, a study was carried out to measure the viscosities of 380 aluminum alloy containing 20 volume % SiC particulates under various shear rates and temperatures. In addition, a viscosity model representing the primary features of the alloy slurries was developed."

Jan 1, 1999

By George R. St. Pierre

A method for the quantitative description of activity interactions between solutes in a metallic solvent which is consistent with stalistical thermodynamic principles is presented. The chemical potential of a solute in an alloy is derived from the weighted mean of its values in the individual solvent components, µi = S?jµi(i). The weighting factors, ?j, are obtained from the distribution functions. The resulting equation contains far fewer adjustable parameters than the Epsilon Formalism and because of its correct functional form it provides an improved fit to the available data on a variety of alloy systems containing oxygen, carbon, sulfur, nitrogen, and hydrogen. For a binary metallic solvent ( A, B ) containing a solute (i), it is shown that

Jan 1, 1995

By Kazuaki Mita

There are various intermetallic compounds in the Zn-Fe system. We synthesized them at about 673K. A specimen was examined chemically and X-ray diffraction was applied to ensure the formation of intermetallic compounds. Material containing two phases was placed in a Knudsen type effusion cell and the mass spectrum studied to evaluate the vapor pressure of zinc. The thermodynamic properties of intermetallics was then evaluated through measured intensity.

Jan 1, 1999

By Hideki Yamamoto, Shigeno Matsumoto, Junji Shibata

"Some fundamental studies were carried out in order to produce composite powders comprising of two or three metal oxides ~y using liquid-liquid extraction and to develop the control technology of the particle size. The combination of samarium and cobalt was selected as the two component composite powders. Both stripping and crystallization occurred at the same time by emulsifying the organic phase loading the two metals extracted with Versatic Acid 10 and the aqueous solution containing oxalic acid. The effect of aqueous pH, oxalic acid concentration and agitation speed was examined on some properties such as crystallization percent, particle size and shape of each metal oxide powders obtained in this process. The analysis by using EDX showed that the two metal oxides were distributed uniformly.IntroductionComposite metal and metal oxide powders with high purity are indispensable as industrial materials in the fields of electrical engineering, electronics and metallurgy. It is difficult to mix metal powders or metal oxide powders uniformly for the production of alloy powders. If insoluble metal salts are allowed to collect as crystallization products in the crystallization-stripping process, the conventional melting and crushing process can be avoided. After mixing of the organic phase containing metals in fixed composition, fine metal and metal oxide powders of alloy composition are produced by using a crystallization-stripping method. Versatic Acid 10 and D2EHPA, both acidic extractants, were chosen in this experiment, and the metal oxide powders were produced by using oxalic acid as a crystallization reagent. Mixed metal oxalates containing samarium and cobalt were precipitated from the mixed organic phase containing these metals. Furthermore, the physical properties of the powders, such as particle size, shape and thermal decomposition, were measured in order to evaluate them for industrial purposes."

Jan 1, 2000

By Bora Derin

The synthesis of titanium diboride (TiB2) by carbothermal reductions of TiO2 and B2O3 was investigated. For this aim, TiO2, B2O3 and carbon black powders were dried, weighed out and mixed in stoichiometric molar proportions (TiO2:B2O3:C = 1:1:5). The experiments were carried out in a graphite resistance furnace in argon media using different range of temperature (1400- 1700 °C) and time (0 and 15 min). The phase analyses observation of the products were examined by using XRD.

Jan 1, 2008

By Grant Wallace, Rod James, Larry Twidwell, Ed Rosenberg, Courtney Young, Sean Dudley, Hsing-Hsin Huang, William Gleason, Jerome Downey

The use of applied chemistry in the production and optimization of leach solutions from Rare Earth Element (REE) ores and concentrates is being investigated. Ore and concentrate samples were characterized using scanning electron microscopy/mineral liberation analysis (SEM/MLA), X-ray diffraction (XRD), and Atomic emission inductively-coupled plasma spectroscopy (ICPAES). Multiple leach tests were performed to analyze the effects of temperature, residence time, and reagent concentration on the leaching of REEs. Analysis of leach solutions was carried out using ICP-AES. Modeling and statistical analysis of extraction behavior was carried out using DesignExpert 9. Modeling data for cerium extraction indicates that extraction is greatly influenced by temperature and reagent concentration, while leaching time plays a much less important role. Experimental design techniques are being utilized to optimize REE recovery. Results, conclusions, and directions for future studies will also be discussed.

Jan 1, 2015