Search Documents

By Fuqiang Guo

Scorodite (FeAsO4, 2H2O) is suitable mineral carrier for immobilization of arsenic-rich wastes. Its stability is, however, highly pH dependent (typically at 4 ≤ pH ≤ 7) and satisfactory only under oxic disposal conditions. In thiswork an encapsulation process using mineralized gels of aluminum hydroxy-oxides is developed to enhance the stability of scorodite under wider pH and redox potential range conditions. The encapsulation involves blending and ageing of synthetic scorodite produced by McGill’s atmospheric scorodite process with aluminum hydroxyl gels derived from controlled hydrolysis of aluminum salts. The amorphous hydrolyzed Al-gel encapsulates the scorodite particles,which upon short-term aging transforms into crystalline Al (OH)3/AlOOH mineral phases providing a robust protection microscopic barrier. Long-termstability testing demonstrates the encapsulation systemto be highly effective in suppressing arsenic release under either oxic or anoxic (100 mV < Eh < 600 mV) potential and neutral-alkaline pH (7 ≤ pH ≤ 9) ranges.

By Baozhong Ma, Qian Li, Yonggang Wei, Shiwei Zhou, Bo Li, Chengyan Wang, Hua Wang

The magnesium-rich nickel oxide ore (w (Ni) =1.09 %, w (MgO)=29.08 %) mixed with 6 % and 8 % anthracite were roasted at different temperatures. XRD and SEM/EDS techniques were utilized to characterize the phase and microstructure transformation of the ores. The results show that lizardite and chrysotile of raw ore were converted into forsterite and enstatite during reduction roasting process. Simultaneously, iron and nickel oxide were reduced and migrated from the initial magnesium silicate. Fe3Si were formed when the roasting temperature went up to 1300 ℃ and 1350 ℃, and a small amount of Ni was observed in it. Temperatures got too high were not benefit to the polymerization of ferronickel.

Jan 1, 2015

By A. K. Kyllo

A study has been carried out on the dusts from Hudson Bay Mining and Smelting&apos;s Flin Flon copper smelter. The aim of the work was to determine the mechanisms of dust formation and the deportment of the various constituents. The work concentrated on the copper converters, but the electrostatic precipitators and baghouse also clean the reverberatory furnace off gas, so some mixing will have occurred. The dust composition was found to vary with distance from the furnace, and to be made up of three major components: solidified droplets, unreacted flux, and condensed particles. The solidified droplets were formed from material ejected from the converter during blowing, while the flux was blown out of the converters immediately after charging. The condensed particles contained the majority of the lead and zinc, as well as the volatile impurities. There was also a significant soluble content of the dusts, increasing with distance from the furnace. The condensed material may be separated from the remainder by a simple washing and sizing technique.

Jan 1, 1996

By J. P. Downey, L. G. Twidwell

"The high density sludge process (HDS) is a commercially proven acid rock drainage wastewater treatment process that is based on acid neutralization and metal precipitation. Previous studies have established that metal removal efficiencies in precipitation-based wastewater treatment applications can be improved through metal ion adsorption on ferrihydrite and/or aluminummodified ferrihydrite. This study was conducted specifically to determine whether the metals removal efficiencies at an existing industrial facility could be improved by promoting ferrihydrite and/or aluminum-modified ferrihydrite precipitation during the pH adjustment stages of the HDS process. The metal tenors of the treated wastewater samples are compared with those obtained through baseline experiments, which were designed to simulate the conventional HDS operation. The subject metals were: aluminum, arsenic, cadmium, copper, iron, manganese, nickel, and zinc.IntroductionThe HDS process is commercially proven ARD wastewater treatment technology that involves raising the wastewater pH by adding hydrated lime, caustic soda, or another alkaline substance. In addition to neutralizing the acidity, many dissolved metals precipitate as pH is elevated. Waste volume is minimized by capturing and immobilizing the precipitated solids.However, ARD streams characteristically contain multiple dissolved metal species. The response of various metals to pH adjustment in the HDS process is neither uniform nor quantitative, so minor to trace concentrations typically remain in the treated wastewater following solid-liquid separation. The effectiveness and applicability of the process would be improved if a means were found to further reduce the metal concentrations.Previous research and industrial applications have proven that metal ion adsorption on ferrihydrite (FH) and/or aluminum-modified ferrihydrite (AMF) increase metal removal efficiencies. Ferrihydrite and AMF are considered ideal for cation and anion adsorption from an aqueous solution at the appropriate pH [1]. Ferrihydrate adsorption of dissolved heavy metals is widely practiced throughout the world [2, 3]. It is established that FH and AMF effectively adsorb As contained in aqueous solutions [4]. Arsenic removal by adsorption on FH is the U.S. Environmental Protection Agency’s (EPA) Best Demonstrated Available Technology [5]. Twidwell and Leonhard also demonstrated that heavy metals (Cd, Cu, Ni, and Zn) are effectively removed from solution by coprecipitation/adsorption using AMF and FH [6]."

Jan 1, 2008

By Pieter Steeneklm, Mazi’ Rejaee

"EXECUTIVE SUMMARYThe automotive industry's search for increased fuel efficiency through component weight reduction has driven the growth in consumption of magnesium metal in the form of die cast alloys. This trend, which began in North America and should soon accelerate in Europe, will require enhanced recycling services since each tonne of metal used for die cast parts production produces about 500 kg of scrap.Currently, the European die cast market is plagued by very high tolling prices for scrap recycling due to lack of competition and high transport costs due to the distances between the scrap generator and the recycling facility. This situation clearly increases the cost of magnesium die cast components and reduces magnesium's competitiveness with other materials. The challenge for the magnesium industry in the short term is to provide cost ·effective recycling solutions for the die cast industry. In addition effective recycling, in the medium to long term, is needed for the anticipated large volumes of secondary or used scrap that will become available as the die cast components reach the end of their life cycle. This paper will present The Antheus Integrated Magnesium Project as a Novel approach addressing some of the key recycling related issues facing the magnesium industry, in particular the die casters. The paper outlines the many advantages of an integrated magnesium metal park, in an overall goal of increasing magnesium metal's competitiveness."

Jan 1, 2000

By M. Hashimoto

The equilibrium distribution ratios of sulfur between molten copper and CaO-fluxes containing caF2 and caC12 were determined in the range of 1300° to 1400° C under carbon monoxide. The rate of approach to equilibrium is rapid and increases with increasing CaCll concentration. In CaO-CaFl-CaCl2 fluxes, the distribution ratio varies in a complex way with temperature and CaFl concentration. The results are compared with those obtained with the binary fluxes of CaO with BaFZ and MgFl ?

Jan 1, 1983

By P. A. Botha

Most sinter producers prefer to use a range of iron ores with the aim to optimize their sinter blends. ISCOR is however limited to the use of ore from two deposits, namely Sishen and Thabazimbi. Only sinter produced from Sishen ore is described in this report. The Sishen iron ore deposit provides high-grade hematite ore with a mean iron content of 65 per cent. Three major ore types are developed: massive, laminated and conglomeratic. The main ore mineral is hematite with minor to trace amounts of quartz, mica, phosphates and, in places, carbonates. A sinter product is characterized by its mineralogical composition and metallurgical properties. The production rate also plays an important role in the economic evaluation of sinter quality. Sinter-pot tests were conducted with varying basicities, given as the ratio of CaO to SiO:< and coke content. The results of these tests were characterized by mineralogical and metallurgical methods. Basicity of a sinter mix directly influences the mineralogical composition and metallurgical properties. The content of calcium ferrite and calcium silicate increases with increasing basicity, thereby increasing the reducibility and cold strength of the sinter product. Experiments performed during this study provided a model for the optimization of the sinter mix with respect to its mineralogical and metallurgical parameters.

Jan 1, 1991

By June-Yong Eom, Jong-Jin Pak, Jung-Mock Jang, Min-Kyu Paek

The nitrogen solubility in liquid Mn-Si, Mn-Si-Fe, Mn-Si-C and Mn-Si-Fe-C alloys has been measured by the gas-liquid metal equilibration technique in the temperature range of 1673-1773 K. The additions of silicon, iron and carbon significantly decreased the nitrogen solubility in liquid manganese alloys. The experimental results were thermodynamically analyzed by the Wagner’s formalism to determine the first- and second-order interaction parameters of silicon, iron and carbon on nitrogen in liquid manganese. The thermodynamic parameters can be used to predict the nitrogen solubility in ferromanganese and silicomanganese alloy melts as functions of the melt composition and temperature at given nitrogen partial pressures.

Jan 1, 2014

By Kezhuan Gu

Data on the kinetics and thermodynamics of dephosphorization are analyzed in terms of the dynamic partition ratio, determined by a combination of slag thermodynamic properties and the balance of oxygen supply and consumption. A recently developed phosphate capacity correlation is combined with data on kinetics to quantify the most significant parameters in controlling the interfacial oxygen potential. The role of slag composition, entrained gas fraction and temperature are discussed in addition to metal carbon and sulfur content. It is demonstrated that the mass transport of oxygen in the slag is enhanced by factors increasing conductivity and inhibited by entrained gas. The mass transfer of phosphorus in the metal is described considering surface renewal induced by CO bubbles.

By K. Tozwa

The electrical conductivity of electrolytes for copper electrorefining and electrowinning processes has been reported by many researchers since 1911. The experimental results show that the conductivity increases with an increase in sulfuric acid concentration and decreascs with an increase in copper concentration. In pure copper sulfate solution, however, the conductivity increases with an increase in the copper concentration. After confirming the conductivity of pure and acidified copper sulfate solutions experimentally, the concentrations of hydrogen ion and free (not hydrated) water in the electrolytes were estimated and it was found that the relation between the conductivity of acidified copper sulfate electrolytes and the products of concentration of hydrogen ion and free water is linear. Accordingly, the conductivity of acidified copper sulfate electrolytes increases with an increase in sulfuric acid concentration and decreases with an increase in copper concentration.

Jan 1, 2003

By R Bartlett

Process engineering-science originally developed for percolation leaching of ore in heaps is extended to the decontamination of unsaturated soil, either in situ or after excavation and emplacement as a soil heap on an impervious pad. Phenomena considered include: soil matrix porosity and permeability; percolating solution retention, capillarity and flow; washing sweep efficiency; optimum solution application rates during leaching; soil agglomeration to improve soil permeability and soluble contaminant transport by diffusion in soil agglomerates. Practical aspects briefly discussed include leach pad construction, solution distribution and recovery from the soil, and solution containment.

Jan 1, 1994

By L. J. Lutz

The U.S. Bureau of Mines has developed an electrorefining process to recover Ni, Co, Cr, and other metals from mixed and contaminated superalloy scrap. The superalloy scrap is cleaned then directly electrodeposited as a Ni -Co deposit. The process recovers approximately 90 pct of the Ni-Co available from the scrap as a 99t pct pure Ni-Co alloy. During electrorefining the electrolyte undergoes a purification process which results in Cr and other refractory metals reporting to the purification residue. Operating data is given for a 3-L compartmented electrolytic cell. Techniques for the removal of Fe, Cr, and trace impurities from the recycled electrolyte are outlined. The economics of a facility producing 15 mt/d of a Ni-Co alloy are also discussed.

Jan 1, 1993

By P. R. Taylor

Titanium carbide and titanium diboride powders have been successfully synthesized by direct treatment of ilmenite concentrates in a non-transferred arc thermal plasma reactor. Methane gas was used as the reducing agent and boron oxide was used as the boron source in these processes. Free energy minimization plots were used to predict the behavior of each system under different molar ratios and operating conditions. Products were characterized by XRD, SEM and chemical analytical techniques. The average size of the ceramic product is in the submicron range. Metallic iron apparently is finely deposited on the surface of the titanium carbide or titanium diboride particles. Minor impurities such as silica, manganese and zircon were converted to the carbide form.

Jan 1, 1995

By Flávia Paulucci Cianga Silvas, Otávio da Fonseca Martins Gomes, Viviane Tavares de Moraes, Denise Crocce Romano Espinosa, Jorge Alberto Soares Tenorio, Guilherme Apostólico Bortolini, Stoyan Gaydardzhiev

"Printed circuit boards (PCB) are particularly problematic to recycle because of the heterogeneous mix of organic materials, metals, and glass fiber. PCBs are found in almost every electroelectronic equipment and their recycling process involves a pre-treatment to separate the products which contain targeted metals. In this work, a physical processing involving sequential shredding and hanuner milling were used to obtain a comminuted sample from scrap printers PCBs. The thus prepared sample was analyzed for particle size distribution and by optical microscopy as well was subjected to pyrolysis, leachabilty and chemical composition determination by XRF. The metals concentration was determined by ICP and AAS. The PCBs have been also analyzed by SEM-EDS (micro-analysis and X-ray mapping). The results show that the studied PCBs are lead free, multilayer with 4 copper layers, have 45% of metals and the copper is present in significantly higher concentration than the rest of the metals.IntroductionThe global generation of e-waste (electrical and electronic equipment waste - WEEEs) grows at a rate of about 40 millions of tons per year [ l].Among this e-waste there are PCBs that are present in almost all electronic equipment. Their composition is heterogeneous and varies according to several factors, including: kind of EEE, when and where it was produced, fabrication technology [2], etc. In printers, the PCBs represent about 6.6- 8 wt.% [3].The PCBs treatment may include physical, pyrometallurgical, hydrometallurgical, ectrometallurgical and more recently bio-hydrometallurgical process. Normally there is a combination between these processes [2, 4, 5, 6, 7, 8, 9, 10].The diversity between the different PCBs composition complicates the recycling process since the composition of metal and others materials can vary according to the models. So characterization is an indispensable step before any processing of PCB to begin. Owing to the above said, the main goal of this work has been set to characterize representative samples of PCBs from printers through physical, chemical and microstructural analyses."

Jan 1, 2014

By Bingliang Gao, Junli Xu, Michal Korenko, Jinzhao Guan, Liangxing Li, Zhongning Shi, Zhaowen Wang, Aimin Liu

Al-Si alloy, a precursor of solar grade silicon, was prepared by direct electrolysis in cryolite molten salt at 950 oC using high purity silica as material, liquid aluminum as the cathode and high purity graphite as the anode. The electrochemical behavior of Si(IV) ion was investigated using cyclic voltammetry method. The electrolysis products were characterized by XRD, SEM/EDS and ICP. The results indicate that the reduction process of Si(IV) on tungsten electrode is a two-step process and there is about 0.6 V gap between the two steps. The contents of boron and phosphorus in the aluminum-silicon alloy are 3 ppmw and 8 ppmw, which will make the directional solidification purification effectively and reduce the cost of preparation solar grade silicon from metallurgical grade silicon.

Jan 1, 2015

By Fabiano A. C. M. Passos, Vanessa P. R. Silva, Lillian M. B. Domingos, Fernanda A. N. G. Silva, Zuleica C. Castilhos, Roberto B. Faria

Wastes from gold mining need to be monitored from the beginning of mining activities until to the mine closure. Wastes from tailings dam were characterized by XRD, XRF, elemental analysis of carbon and sulfur and ICP-OES. In flotation waste (FW) were observed quartz, dolomite, pyrite, muscovite and chamosite were observed. Meanwhile, in cyanidation waste (CW), besides those described in FW, minerals such as sphalerite, galena, pyrrhotite, microcline and albite were detected, indicating a higher concentration of sulfide minerals in the cyanidation waste. In relation to C and S content, to FW and CW, they were 2.5 and 0.0% and 0.64 and 15.4%, respectively, confirming the majority of sulfides at CW sample and indicating the absence of the flotation organic reagents at the cyanidation waste. The analysis by ICP-OES indicated As, Zn, Pb, Cr and Cd content for FW and CW: 13.30 and 343 mg/kg; 399 and 7,900 mg/kg; 136 and 13,000 mg/kg; 130 and 260 mg/kg; 3.60 and 84.60 mg/kg, respectively. It was also verified significant levels of heavy metals, which indicates the necessity of performing wastes toxicity tests.

Mar 1, 2017

By Yue Tian, Shengqian Wang, Lifeng Zhang

This paper is to discuss the removal of non-metallic inclusions from molten steel using a high frequency magnetic field. In experiments, a certain amount of aluminum was added to the molten steel in a crucible to generate aluminum inclusions. A layer of aluminum clusters were observed close to the wall of the crucible after the electromagnetic (EM) field was imposed. Three dimensional EM field and fluid flow simulation were performed and showed that over 91% inclusions transported to the skin depth (2.31 mm) of the molten steel. The calculation of inclusion removal agreed well with the experimental observation. The separation mechanisms of inclusions from the molten steel by the high frequency EM field were discussed.

Jan 1, 2014

By Motang Tang, Chaobo Tang, Shenghai Yang, Lulu Guo, Yun Li, Yongming Chen, Jing He

A new innovative process for one-step and cleaner extraction of lead from spent lead-acid battery by reductive sulfur-fixing smelting was presented. This paper summarized and discussed several potential sulfur-fixing agents and molten salts which can be used in this new technique. Thermodynamic analysis involving reaction mechanism, ΔGT and predominance-area diagrams of different smelting systems were performed, respectively. The results proved the technical feasibility and high-efficiency of this process. Copper oxide ash (CuO), zinc oxide ash (ZnO) and iron oxide bearing residues (FexOy) can be used as sulfur-fixing agent to extract lead through exchange reactions. Sulfur-fixed efficiency of CuO, ZnO and FeO decrease slightly in turn. Sulfur contained in PbSO4 is fixed in form of Cu2S, ZnS and FeS respectively which avoids SO2 emission. The addition of molten salt can significantly decrease temperature of reductive sulfur-fixing reactions. Molten salt can be regenerated and recycled in smelting system after filtering solid residues.

Mar 1, 2017

By Peter A. Spencer

The metallurgical parameters necessary for the design of a carmercial scale bio-oxidation plant have been determined for the treatment of a refractory arsenopyrite concentrate using a moderately thermophilic bacterial culture. The parameters considered were bio-oxidation rate, culture growth rate, nutrients, solids density, level of bio-oxidation, particle size distribution and oxygen uptake rate. The approach for obtaining the optimum values for these parameters is discussed and values based on results fran batch and continuous testing are given. Estimates of the capital and operating costs for a plant treating the carmercial arsenopyrite concentrate have been calculated fran the test data.

Jan 1, 1990

By Xiang-dong XING, Zhen-yang wang, Xing-le LIU, Jian-Liang Zhang

Experiments were carried out by adding CaF2 as catalyst in a Ar atmosphere to study the isothermal reduction kinetics of vanadium titano-magnetite carbon composite pellets under high temperature in the range from1473 to 1673K. By analyzing reduction mechanism, it was found that the rate controlling step was gas diffusion, and the activation energy was 178.39kJ•mol-1 without adding any catalysts. Adding CaF2 of 3% to vanadium titano-magnetite carbon composite pellets can decrease the apparent activation energy of reduction, and the decrease extent was 14.95kJ•mol-1. In addition, temperature is an important factor influencing on reaction rate.

Jan 1, 2015