Search Documents

By Grigore Matei

The thermodynamic properties of CuzS-FeS system are important not only in the ease of copper smelting but also in the case of general pyro-metallurgy. However there arc not many reported activity data In this study, activities of FeS and CU2S in the Cu2S-FeS system were calculated using the Darken's method from the activity data of the Cu2S-FeS-Sb2S3 systems measured by the transportation method at 1050°C. The activities of Cu2S and FeS in the Cu2S-FeS system showed negative deviation from the ideal behaviour and satisfied the relation of the Gibbs-Duhem equation.

Jan 1, 2003

By Yuanbo Zhang, Zhixiong You, Daoxian Duan, Guanghui Li, Tao Jiang, Xiaohui Fan

"Presently, high-grade manganese oxide ores are usually utilized by a coal-based reduction roasting process. However, there were some obvious drawbacks, including serious environmental pollution, high energy consumption, etc. The reduction temperature is relatively high (850-900 °C). In this study, a kind of biomass, pine black charcoal, was used as a reductant to reduce low-grade manganese oxide ores. Under the optimal conditions of reduction temperature of 600~650 °C, roasting time of 30~45 min and ratio of ore to reductant 5:1, the leaching efficiency of manganese reached more than 98%. Compared with the traditional coal-based reduction process, the reduction temperature is reduced by 250-300 °C.IntroductionManganese plays a very important strategic role in the national economy, and it is widely used not only in the metallurgical industry, but also in the light industry, chemical industry, medicine, agriculture, etc [1]. The average grade of manganese ores in China is evenly about 21%, which belongs to typical low-grade manganese ores [2]. Therefore, large quantity of high-grade manganese ores is required to import in order to meet the rapid development of Chinese manganese industry. As reported, the conventional treatment of reduction roasting has been widely applied for processing manganese oxide ores, in which coals or reducing gases (CO, H2 or CHi) were usually used as reducers [3]. However, there were some insuperable problems, such as high energy consumption, poor operating conditions, serious environmental pollution, etc [ 4-9]."

Jan 1, 2013

By Baohua Li, Yanhui Liu, Shengping Li, Xuewei Lv, Yun Chen

There are almost ten billion tons of vanadium-bearing titanomagnetite in Panzhihua-Xichang area. However, iron ores in Hongge, which has the most abundant reserves in the four mine areas in Panzhihua, have not been utilized sufficiently so far. The reason behind this is the relatively high Cr2O3 in the ores (0.49 %~0.82 %), that due to its high melting temperature will negatively influence the blast furnace reduction and slagging process. Therefore, in the blast furnace process, Cr is hope to be reduced into molten iron, which can reduce slag viscosity problems. Slag iron reduction experiments were conducted to quantify the Cr reduction. Experimental results shows that with the increase of TiO2, the content of Cr in the hot metal is decreased when balanced. And during the initial stage of the reduction reaction, the reaction kinetic model is a first-order reaction.

Jan 1, 2016

By Frank M. Kimmerle

Spent Potlining (SPL) contains recoverable chemical elements (C, F, Na and Al) which are lost in stabilization or immobilization processes primarily aimed at eliminating cyanides and reducing leach rates of soluble fluorides prior to landfiling. They can be recovered in a variety of mineral forms for recycling in the aluminum industry and elsewhere. Alcan has developed a cost-effective hydrometallurgical route, combining a number of proven unit processes to destroy cyanides, recycle the chemical values and provide a zero-discharge process. Pilot plant studies of this Low Caustic Leach and Liming (LCL&L) Process prove that the fluoride scan be converted to acid grade fluorspar, while the sodium and aluminum are recovered as a sodium aluminate and caustic feed to the Bayer Plant operations. The remaining brick and carbon fraction constitutes a high ash solid fuel which meets TCLP leach criteria and whose reduced sodium content enhances its value as a chemical reducing agent.

Jan 1, 1994

By W. S. Hui, M. G. Silva-Valenzuela, H. Wiebeck, F. R. Valenzuela-Diaz, B. B. Michel

Biodegradable polymer microcapsules have been used as a control sustained release system with many applications. Studies reveal that the incorporation of nanoparticles improves matrix properties, even more so if the clay is modified. The objective of this work was to compare microcapsules of poly (succinate-co-butylenelactate) (PBSL) reinforced with Brazilian clay, composed of smectites and kaolinite, in its natural (MMT/K) and modified (O-MMT/K) forms. Nanocomposites and microcapsules were synthesized by emulsification-diffusion of solvent and solvent diffusion methods. Its characterization was then performed by scanning electron microscopy (SEM), stereo microscopy and wide-angle X-ray diffraction (XRD). The results reported corroborate that PBSL/OMMT-K form an intercalated montmorillonite and kaolinite nanostructure, capable of generating uniform spherical microcapsules with diameter values smaller than that of PBSL/MMT-K, reaching 5–10 lm. DRX indicates that there was a real change in the clay structure. The incorporation of modified clay showed an improvement in surface quality and the strength of microcapsules, making it possible to produce smaller sizes.

Mar 1, 2018

By Marc Liebman

We present the results of a telephone survey of electric arc furnace (EAF) steel producers. This report characterizes the current status of EAF dust generation, treatment and disposal. It indicates the quantity generated, zinc content, other relevant constituents, and plans and trends that will impact on the quantity and characteristics of the dust generated. The survey covers EAF based steel producers in the United States and Canada. It identifies the processors currently employed, opinions about the use of these processors and services, as well as new technologies being considered.

Jan 1, 2000

By Wang Shuchan, Zhang Zimu, Zhang Dianhua, Liu Yan, Zhang Ting-an, Zhao Qiuyue, Lv Chao

Rare earth extraction tank has many adverse effects like big floor space and high production accumulation during industrial production. Current researches usually focus on changing the device structure without making a breakthrough towards gravity clarification. This paper attempts to achieve this goal by using both the action of clarification by gravity and clarification by stirring. Because many physical parameters affect the clarification and separation rates, the density, viscosity and surface tension of the two phases were determined at different temperatures and different concentration of aqueous solution. The innovation of this research involves adopting the Karl-Fischer method to investigate water content in oil phase during the stirred separation process. In this paper, the separation effect of different physical parameters was studied and the dimensional equation between water content and the physical parameters was established by combining with the experimental data.

Jan 1, 2014

By Wen-long Zhan, Zhe Ning, Jun-hong Zhang, Teng-fei SONG, Zhi-jun He, Qing-hai Pang

In order to investigate the influence of granularity on the gasification property of coke after microwave irradiation, comparison of ordering of carbon structure and internal microstructure of granular coke before and after microwave pretreatment was carried out. It is shown in X-ray diffraction results that the diffraction intensity of the coke sample significantly increased after 40 s irradiation under 264 W microwave power, which indicated the decrease in reactivity of coke.

Mar 1, 2017

By M. Zamalloa

Slag foaming is an important phenomenon in many metallurgical processes. It creates large surface areas for multi-phase reactions to take place. In other applications, it protects electrodes and improves the energy efficiency by reducing radiation from hot surfaces. However, it may also be a source of serious disturbances. To control and optimize the use of slag foams, an extensive knowledge of the factors controlling the foam formation and stability is required. Slag foaming experiments were carried out using synthetic FeO-CaO-Si02 slags at temperatures ranging from 1200 to 1350 "C. A data acquisition system was used to continuously measure the foam height, gas flow rate, bubble frequency and temperature. The experimental results show that the gas injection rate has a strong effect on the behaviour of slag foams. At high flow rates and rapid bubbling, unstable foams with short decay times were created. The addition of P20, favours the foam formation and stability by lowering the surface tension of the slag. The average foam life increases with decreasing basicity (CaO/Si02). It is proposed that this is attributed to the increase of the surface viscosity due to surface adsorption of a thin film of silica, retarding the drainage of the liquid films.

Jan 1, 1992

By Ji-He Wei

Keywords: stainless steel, AOD refining, side and top combined blowing, mixing characteristics, water modeling The fluid mixing characteristics in the bath during the side and top combined blowing AOD (argon-oxygen decarburization) refining process of stainless steel have preliminarily been studied on a water model unit of a 120 t AOD converter. The geometric similarity ratio between the model and its prototype (including the side tuyeres and the top lances) was 1:4. On the basis of the theoretical calculations for the parameters of the gas streams in the side tuyeres and the top lances, the gas blowing rates used for the model have more reasonably been determined. The influence of the tuyere number and position arrangement, and the gas flow rates for side and top blowing on the characteristics has been examined. The results demonstrated that the liquid in the bath underwent vigorous circulatory motion during gas blowing, without obvious dead zone in the bath, resulting in a well mixing effectiveness. The gas flow rate of the main tuyere had a governing role on the characteristics, a suitable increase in the gas flow rate of the subtuyere could improve mixing efficiency, and the gas jet from top lance could make the mixing time prolong. Corresponding to the oxygen top blowing rate specified by the technology, a roughly equivalent and good mixing effectiveness could be reached by using six side tuyeres with an angle of 27° between each tuyere, and five side tuyeres with an angular separation of 22.5° or 27° between each tuyere. The relationships of the mixing time with the gas blowing rates of main-tuyeres and sub-tuyeres and top lance, the angle between each tuyere, and the tuyere number have been obtained.

Jan 1, 2005

By Xiangru Chen, Honggang Zhong, Qijie Zhai, Qingqing Sun

"A horizontal directional solidification equipment, with an in-situ pouring system, was employed to physically simulate the solidification behavior of continuous casting. In this paper, the 2304 duplex stainless steel (DSS 2304) was investigated using this equipment due to its microstructure produced by continuous casting process was usually not satisfied. The grain size combined with the position of columnar to equiaxed transition (CET) of DSS 2304 were observed and the results showed these microstructure characteristics were very close to those of the continuous casting slabs. In addition, the influences of pouring temperatures and cooling conditions on the CET behavior were investigated. The results revealed that the length of the columnar grains decreased with decreasing the pouring temperatures and flow rates of the cooling water. Besides, the content of austenite decreases with increasing the distance from the chilled sidewall.IntroductionDuplex Stainless Steels (DSSs) have been widely used in industry for their excellent mechanical strength and superior corrosion resistance in Cl- environments when compared with other stainless steels [1,2]. Their good performances are mostly on account of the duplex phase structure-ferrite (d) and austenite (?) and the high proportion of alloying elements. Although, DSSs have good ductility, but worse formability compared to the austenitics, and this is the key to restrict DSSs application [3]. This is due to the differences properties between the two phases. The hot workability of ferrite (d) is better than austenite (?) and exhibits a lower flow stress during hot rolling processing [4]. The early workers had revealed that coalescent force of phase interface, microstructure, difference of mechanical property between two phases and the precipitations are the main factors affecting the formability of DSSs [5,6]. Another important reason that affects the alloy’s mechanical properties is columnar to equiaxed transition (CET) [7]. It often occurs during continuous casting solidification process and induces inhomogeneous mechanical properties and the microstructure varies with different processing parameters, such as pouring temperatures, cooling conditions (water flow rates in the cooling zones) and casting speed [8]."

Jan 1, 2012

By Taiping Lou

The coarsening process of precipitates in non-equilibrium systems was studied, and then a physical model of coarsening was proposed. The coarsening process of CaO'TiO2 in MgO-TiO2-Al2O3-SiO2-CaO-CaF system was investigated. It is shown that the coarsening process by the model predicting is agreed with the experimental results.

Jan 1, 2000

By Pinakin C. Chaubal

An industry ? university consortium was set up to develop advanced tools necessary to understanding of the various phenomena occurring in the hearth of the modern iron making blast furnace. The major driver for this work was to provide the technological support required to extend campaign life of blast furnaces, which, by current agreement is tied to the life of the furnace hearth. The hearth wear is significantly affected by the hot metal velocity, temperature distribution and refractory temperatures. Due to the difficulty in making measurements inside the hearth, novel approaches to gain a fundamental understanding of the detailed physical and chemical processes in the hearth must be developed. The approach used in this project was to develop a 3-D CFD (Computational Fluid Dynamics) model coupled with extensive validation efforts. The CFD model is being utilized (1) to understand the phenomena in the hearth, (2) to understand the impact of changes in the internal conditions of the hearth on wear patterns; and (3) to design a monitoring/controlling system for prolonging campaign. In this paper, the results will be reviewed.

Jan 1, 2006

By Young-Chul Kang

The Onsan Copper Smelter of LG-Nikko Copper Inc. is a unique plant, which has been operating two smelting processes since 1998. The operation of the first one was started in 1979 with a capacity of 80,000tpy of copper in concentrates utilizing Outokumpu flash-smelting technology. The other one was started in 1998 based on Mitsubishi continuous process with a capacity of 160,000 tpy of copper in concentrates. Through several expansion projects, the total smelting capacity of both processes is expected to reach 430,00Otpy of copper in concentrates towards the end of 2002. This article describes operation advantages of having two different processes at one plant and comparative operation results in terms of productivity, impurity distribution, energy consumption and environment issues and etc.

Jan 1, 2003

By M. Kawakami

In relation to the designing of a new-type blast furnace, the reaction of carbonaceous materials with C02 is expected to occur at as low temperature as possible. In order to get a highly reactive carbonaceous material at low temperature, the reaction kinetics was investigated by measuring such quantities as the reaction rate from weight loss, the amount of CO adsorption and specific surface area by BET method. The reaction rates were large in the order of the Bintyo char, metallurgical coke, graphite and glassy carbon. If the rate was converted to the rate per unit area, however, those of the Bintyo char was smaller than that of graphite. Thus, it is suggested that the rate of the Bintyo char is influenced by the pore diffusion of C02. The rate had a positive relation with the amount of CO adsorption, showing that the rate determining step would be the desorption of CO from the active side on the surface. The rate independent of surface area was derived, combining al\ the obtained data.

Jan 1, 2003

By M. Kawakami

In relation to the designing of a new-type blast furnace, the reaction of carbonaceous materials with CO2 is expected to occur at as low temperature as possible. In order to get a highly reaetive carbonaceous material at low temperature, the reaction kinetics was investigated by measuring such quantities as the reaction rate from weight loss, the amount of CO adsorption and specific surface area by BET method. The reaction rates were large in the order of the Bintyo char, metallurgical coke, graphite and glassy carbon. If the rate was converted to the rate per unit area, however, those of the Bintyo char was smaller than that of graphite. Thus, it is suggested that the rate of the Bintyo char is influenced by the pore diffusion of CO2. The rate had a positive relation with the amount of CO adsorption, showing that the rate determining step would be the desorption of CO from the active side on the surface. The rate independent of surface area was derived, combining all the obtained data.

Jan 1, 2003

By Huang Kai

By adding the solid oxalate acid powder into the solution of nickel chloride or its ammonia coordinated solution, the uniform compound particles were prepared and the precipitated particles were transferred to the mono-dispersed NiO particles by calcination. In this study, the various experimental conditions were investigated, the characteristics of the corresponding obtained particles were analyzed, and the formation mechanism of the particles was elucidated. It was found that the solid oxalate acid provided the solid-solution interface for the precipitation and induced the nucleation and growth of the product particles.

Jan 1, 2005

By Jae R. Lee

Keywords: Self-propagating high temperature synthesis, AlN, Powder synthesis The particle size and shape effects of starting raw powders on the synthesis of aluminum nitride by self-propagating high temperature technique under high nitrogen pressure were investigated with various AlN diluents and Al reactants. It was found that the structure of beds of the starting raw particles largely affected the pore channels for nitrogen gas infiltration as well as the passages for combustion propagation before and during the reaction, resulting in the morphology and purity changes of the synthesized products. The AlN product of purity over 98% with about 30 microns was obtained.

Jan 1, 2005

By Grigore Matei

The thermodynamic properties of CU2S-FeS system are important not only in the case of copper smelting but also in the case of general pyro-mctallurgy, However there are not many reported activity data In this study, activities of FeS and CU2S in the CU2S-FeS system were calculated using the Darken's method from the activity data of the CU2S-FeS-Sb2SJ systems measured by the transportation method at 10S0°C. The activities of CU2S and FeS in the CU2S-FeS system showed negative deviation from the ideal behaviour and satisfied the relation of the Gibbs-Duhem equation,

Jan 1, 2003

By Yoichi Takeda

Copper solubility in Si02-CaO-FeOx slag equilibrated with copper matte in 10% S02 atmosphere at 1573K was estimated. Essential parameters are activity coefficients of copper oxide and sulfide, oxygen and sulfur potentials and activity of copper in the slag-matte system. A large number of experiments provide proper parameters to calculate copper solubility in slag. A classical thermodynamic model postulating CUOO.5 and CuSo.; molecules assists in estimating copper solubility in slag. Additions of Si02 and CaO reduce copper solubility almost in any condition. Copper loss, that is function copper solubility and slag volume, in the silica saturated Si02-FeOx binary slag is minimally equilibrated with less than 66% copper matte while copper loss in the 50% FeOx-SiOrCaO ternary slag saturated with 2CaOSi02 is minimally equilibrated with over 66% copper matte. This slag composition has potential for continuous copper converting, direct copper production or high-grade matte production.

Jan 1, 2003