Search Documents

By P. Chris Pistorius

Calcium treatment of alumina inclusions, to convert the alumina to molten or partially molten calcium aluminates, is a well-established treatment for steel, to improve the castability of aluminium-killed steel. However, the role of magnesium in calcium-treated steel is not fully clear, nor is the origin of the several percent of magnesium oxide that is often present in calcium-treated inclusions. To study this, steel was sampled after calcium treatment at an industrial steel plant, and the inclusions identified by energy-dispersive X-ray microanalysis (EDX) on polished sections of the samples (analysing the samples in a scanning electron microscope). The predicted fraction liquid in the inclusion was estimated from the ternary alumina-magnesia-lime phase diagram. Inclusions with higher CaO contents generally had lower MgO contents, indicating that the calcium wire is not the origin of the magnesium in the inclusions; this was also confirmed by wet chemical analysis of the calcium wire. Instead, it appears that magnesium-alumina spinel inclusions form during extended ladle contact after aluminium killing and before calcium treatment. While such spinels have been stated to cause poor castability (clogging the submerged-entry nozzle), it is clear that calcium treatment successfully modifies the spinel inclusions to mixed alumina-lime-magnesia inclusions, where the magnesia content contributes substantially to liquefaction of the inclusions: for typical MgO contents of around 10%, the range of Ca:O ratios which yield liquid (or partially liquid) inclusions is extended substantially to lower Ca:O ratios.

Jan 1, 2006

By David R. Sadedin

The highly negative Gibbs free energies of hydrogen atom reactions suggest that refractory oxides such as titanium dioxide should be easily reduced by hydrogen atoms. These reactions appear to be most favourable at low temperatures; oxides should be reducible even at room temperature. Since hydrogen atoms are produced in plasmas containing hydrogen a number of investigators have used hydrogen plasmas of various sorts to test these possibilities for reducing refractory oxides, in particular TiO2. None of these attempts has succeeded, a small degree of reduction being achieved in only a thin layer near the surface. A deeper consideration shows that several factors complicate the reactions expected on the basis of the negative Gibbs free energy. One factor is that the back reaction by water molecules produces molecular hydrogen, not hydrogen atoms, and the metal atoms that have been reduced may be immediately re-oxidised. In plasmas there are complications due to diffusion, thermal and charge boundary layers and charged particle reactions. Interpreting the results of hydrogen atom reactions is difficult. Hydrogen is not detectable by electron dispersive spectroscopy and amorphous products are not determinable by x-ray diffraction. Another consideration is economics. The cost of producing hydrogen atoms has a large bearing on the metals for which hydrogen atom reduction may be competitive. In this paper these factors are discussed, some necessary basic studies are highlighted and the general principles of a laboratory reactor are given, together with the results of tests using ZnFe2O4, ZnO and TiO2 as test oxides.

Jan 1, 2006

By Rivera Jose Antonio Ore

Top Submerged Lance (TSL) smelting technology is currently used in a wide range of applications in the non ferrous and waste product treatment industries. The use of TSL technology for tin concentrates smelting has been successfully applied at the Minsur Tin Smelter and Refinery at Pisco, Perú. The process is based on the air-cooled top entry submerged Sirosmelt lance, developed by Dr. John Floyd at the CSIRO division of Mineral and Process Engineering in the 1970?s. Advantages of the process include flexibility to operate the lance, main burner of the Sirosmelt furnace, with different levels of combustion stoichiometry which allows us to get from highly reducing to highly oxydising atmospheres in the smelting reactor according to the type of feed we are processing, ability to utilize cheap energy sources such as natural gas, low capital cost and an environmentally friendly operation. This presentation summarises the application of the Submerged Sirosmelt technology for smelting tin concentrates and a variety of tin containing materials like iron dross, copper dross, tin residues, low tin/antimony slags by applying recent metallurgical developments at the Minsur smelter. The impact of new feed conditions and level of impurities on reactor performance with features of process and operation control are described. As a result of these recent advances in tin smelting using TSL technology, the Minsur Tin Smelter and Refinery improved its overall tin recovery, substantially reduced tin inventories and became the second largest tin smelter in the world, currently producing more than 40,000 metric tones of refined tin per year.

Jan 1, 2006

By Daniel Kim, Justin McAllister, Shijie Wang

"At the Kennecott Utah Copper Refinery, impurities in the electrolyte are being precipitated in the circulation system and form a hard scale in the piping. This scale must be removed periodically for proper electrolyte flow. Distinct layers of differing composition form as the operating conditions of the tank house change. Scale samples from the inlet and outlet pipes were analyzed to discover the nature of the precipitates. Each sample was sectioned and examined under optical microscopy and SEM. The composition of the scale was analyzed using ICP, XRD, and SEM/EDX mapping. The rate of deposition was determined by measuring the amount deposited on new pipes after elapsed time intervals. In order to determine how to minimize the formation of the scale, the mechanism was studied and the results are presented in this paper.IntroductionIn copper electrorefining, impure copper anodes are refined into pure copper cathodes. The impurities from the anodes are either insoluble and report to the slimes or soluble and dissolve concentrating in the electrolyte. These impurities are controlled by bleeding electrolyte from the system. Over time, the impurities combine to precipitate a hard scale on the surfaces contacted by the electrolyte. The scale causes problems with tank house circulation systems. In order for the refinery to operate properly, the scale must be removed periodically from the walls of the pipes. The first step to control the buildup of scale on the pipes is to understand the composition and the phases that are present in the scale."

Jan 1, 2012

By Christine Wenzl, Andreas Filzwieser, Stefan Konetschnik

"The METTOP-BRX-Technology is a novel manifold electrolyte inlet, which allows improved productivity and production in new and existing tankhouses by achieving higher current efficiency and cathode quality, as well as using current densities higher than 400 A/m2. Two installation examples are shown: Montanwerke Brixlegg AG, Brixlegg, Austria (upgrade of existing tankhouse) and Xiangguang Copper, Yanggu, China (new tank house). Montanwerke Brixlegg AG has been using the METTOP-BRX-Technology since 2005, and converted half of the whole tankhouse to METTOP-BRX in 2011 in order to use a current density of more than 400 A/m2. Xiangguang Copper started up their second tankhouse in May 2011. This tankhouse was constructed in the same way as the existing tankhouse, but was designed for 292,000 t/a cathode copper (existing tankhouse: 200,000 t/a) by using the METTOP-BRX-Technology. This production increase is a consequence of a much higher current density, namely 410 A/m2, compared to 280 A/m2 in the old tankhouse.IntroductionCopper electrorefining has been practised for more than hundred years, the last big change being the implementation of stainless steel cathodes in the 1980s [1], In 2005, the METTOP-BRXTechnology was first introduced. This technology was developed jointly by METTOP and Montanwerke Brixlegg, Austria, and allows improvements in productivity and production in new and existing tankhouses in an economic way. The METTOP-BRX-Technology is a novel manifold inlet that allows improved tankhouse productivity by increasing current density and/or current efficiency while maintaining or improving cathode quality [2]."

Jan 1, 2012

By D. Valic

In 1997, 9.2 million tonnes of mined, recoverable copper was produced, of which, 1.8 million tonnes or 19.4% was produced by leaching, solvent extraction and electrowinning. The amount of copper produced by this method grew faster than those attained from concentrate smelting, signifying the growing importance of this low-cost production method. Statistical experimental design, unlike traditional approaches, allows for proper distribution of experiments within the boundaries of factors being studied such that the number of experiments required to develop a sound relationship between the factors and a response is minimized. In the past, very little use has been made of statistical experimental design in copper electrowinning studies. Traditional one- variable-at-a-time approaches are widely employed for this purpose. The present study employs a factorial experimental design to relate current efficiency with current density (180 and 300 A/m2), copper concentration (25 and 65 gL), and temperature (40 and 60 °C). Pure synthetic electrolyte with a constant acid concentration of 180 g/L was used throughout the study. The designed study produced a linear relationship where the independent variables of current density, copper concentration, and temperature, and their interactions, were found statistically significant. It was shown that current efficiency could not solely be used as a predictor of copper cathode quality. The quality of the deposit is difficult to be incorporated into a model or relation. It was determined that other measures, such as cathode morphology and crystal structure should be considered. This was done through XRD and SEM analysis.

Jan 1, 1999

By Dachun Liu, Yifu Li, Baoqiang Xu, Yongnian Dai, Bin Yang

"The removal of impurity arsenic from crude tin is one of the major problems in the process of tin refining. Through a thermodynamic analysis on vacuum refining process of crude tin, the vapor pressure of impurity arsenic under different temperatures can be obtained, which demonstrates that it is possible to separate tin and arsenic by the vacuum refining process. This paper attempts to verify the behaviors of impurity arsenic. The experiment result shows that through vacuum distillation, crude tin with 0.16% arsenic can be refined from crude tin with 0.96% arsenic, and about 50% impurity arsenic can be collected in the form of metallic arsenic.PrefaceThe crude tin obtained by the reduction process is insufficiently pure for most applications, even smelting from tin concentrate. Arsenic is a common impurity in crude tin and also one of the predominant elements to affect tin performance. Arsenic is a poisonous metal that has long been linked to an increased risk of cancers, diabetes, thickening of the skin, diseases of the liver and digestive complications, so there is a mandatory limit on the amount of arsenic (<0.015%) in tinfoil wrapper and tin layers for food packaging. Arsenic causes a poor appearance and plasticity, and increases viscosity. The impurities content of crude tin fluctuate over a wide range; a lot depends on composition of tin ore concentrate, treatment method and technological process before reduction smelting. And the content range of arsenic is usually 0.5~4%, but it is higher in some factories."

Jan 1, 2012

By Tao Li

The development of DP(Dual Phase) steels and TRIP(Transformation Induced Plasticity) steels has received much attention in recent years due to their high strength and simultaneous good ductility, which provides the potential for weight reduce and resource savings on certain components in automobile or other industries. So a controlled rolling process was simulated in the present study by thermomechanical simulator (Gleeble 1500) for producing DP steels on a kind of low carbon steel containing a small amount of Si and Cr. F+M dual phase microstructures have been obtained during continuous cooling processes of a wide cooling rate range from 10°C /s to 60°C /s. The grain size of the dual phase steel developed can be refined to less than 5 m through the mechanism of deformation induced ferrite (DIF) transformation. The ultrafine ferritic grains are equiaxed with high-angle boundary, and the martensite islands of an average size less than 5m disperse uniformly in the ferrite matrix. The ultrafine martensite islands not only inhibit the growth of ultrafine ferritic grains and improve the bonding of F/M interface, but also increase remarkably the strain hardening rate in the processing of the present Dual-Phase steel. As a result, the tensile strength of ultrafine grained Dual-Phase steel reaches higher than 1000 MPa. The result shows that an ultrafine grained Dual-Phase steel of low carbon and low alloy is promised to exhibit desired F+M microstructure by means of this new TMCP process.

Jan 1, 2006

By Zhihong Liu

In recent years, the removal of arsenic from different types of high arsenic containing materials produced in nonferrous metallurgical processes have been experimentally studied in the complex materials processing research group from Central South University. These materials include arsenic and antimony bearing flue dust, arsenic sulfide residue and arsenate bearing flue dust. The separation of arsenic from other valuable metals was carried out hydrometallurgically; for each type of arsenic bearing material, different processes have been employed individually to remove the arsenic effectively. In this paper, the flowsheets and typical experimental results have been summarized.

By A. F. Sidorov

A method of improving mineral recoveries from ores by modifying the physical and chemical properties of minerals using radioisotope radiation was tested. It was observed that irradiation modifies mineral cell sizes, changes the crystal structure of some minerals, reduces the sulfur content 1 to 1.5 % in sulfides, changes the zeta potential, alters the surface properties of mineral grains I and produces other changes. Preliminary tests indicate that accelerated electron treatment of ores in connection with mineral processing has a potential for improving mineral recoveries by flotation and by magnetic separations.

Jan 1, 1989

By Anders Salwén

In 1975 T. Nishizawa and A. Chiba reported on observed deviations from the ferrite-austenite local equilibrium in several diffusion couples based on the Fe-Cr system. In order to try to verify these results the austenite-to-ferrite transfonnation in a Fe-20 %Cr-Invalid Code [Fe-]-%Cr diffusion couple held at 1100 for 100 hours has been simulated. The simulation model is based on the postulated principle of maximum dissipation rate of Gibbs energy during transformation, which allows non-equilibrium interface conditions. Keynotes: Computer Simulation, Austenite-to-Ferrite Transfonnation, Diffusion Couple

Jan 1, 2003

By N. A. McKay, J. G. Davison

"Heap leachable ore deposits from many countries have been submitted for process mineralogical evaluation and laboratory testwork. Numerous factors must be addressed and integrated by the mineralogist, geologist, metallurgist and engineer. Projects encompass grass roots exploration, preliminary petrographic analysis, predictive and process mineralogy, dye penetration analysis of rocks and thin sections, metallurgical beneficiation testwork and plant optimization studies. The significance of mineralogical factors, such as geological controls, degree of oxidation, dye amenability, liberation, deleterious minerals, refractoriness, and the impact of mineralogy on gold recovery and process considerations, will be presented.ABSTRACT ONLY"

Jan 1, 1997

By M. Cloete, C. MacLagan, A. Newall

This paper initially gives a brief overview of Zinc Corporation of South Africa Limited (Zincor). The original design parameters of the Zincor roasters are compared to the current operation, and the requirements for efficient roasting are listed. Roaster operational problems experienced during the early to mid 1990's are outlined. A description of the investigation and the outcome to increase overall roaster availability are given. The history and the development of the use of oxygen at the Zincor roaster operation, with an account of the associated operational experiences, are explained.

Jan 1, 2000

By J. Peter, S. E. James, J. L. Watson

A survey of operating zinc smelters and refineries throughout the world has been done in conjunction with the Lead-Zinc 2000 Symposium. This survey follows the examples set by the Japanese Mining Industry Association in 1985 and 1995. Questionnaires were sent to operating zinc plants that covered feed materials, process details, energy consumption and labor requirements. The voluntary responses to the survey were tabulated. Key operating parameters including feed grade, production capacity, quality of the intermediate products and quality of the final products have been compared for both hydrometallurgical and pyrometallurgical processes.

Jan 1, 2000

By W. Marnette

Norddeutsche Affinerie is the largest West European copper producer with an annual output of more than 350,000 tonnes of refined copper, about half of which is produced from copper concentrates. However, in addition to concentrates, Norddeutsche Affinerie processes secondary raw materials and recycling materials which contain a combination of copper and lead. These materials were previously treated in blast furnaces, a technology which has meanwhile been superseded at NA by the electric furnace process, primarily owing to the necessity of complying with the increasingly stringent requirements for environmental protection.

Jan 1, 1994

By V. A. Bryukvin

A hydroelectrochemical technology has been proposed and experimentally proven for processing metallic gold- and silver-containing concentrates on the basis of copper and copper alloys obtained as a result of preliminary physico-mechanical upgrading of electronic scrap. The proposed technology is based on hydroelectrochemical leaching of scrap using reversible electric current and diluted nitric acid solutions, containing complexing agents, permitting complete separation of gold from the nonferrous matrix without involving gold in the process, and dissolving copper, zinc, lead and tin virtually without any emission of nitrose gases.

Jan 1, 2006

By Frank R. A. Jorgensen

Flash smelting is used to smelt a large proportion of the world&apos;s copper and nickel and some lead/zinc concentrates. Understanding the factors controlling the ignition of these concentrates is an important consideration in designing burners and maximising the throughput of the flash smelting process. The literature on the subject is briefly reviewed and techniques for the measurement of ignition temperature discussed. The mineralogy of the concentrates and the role of thermodynamics and phase diagrams in interpreting and predicting ignition behaviour are emphasised and applied to interpreting results obtained on a nickel concentrate.

Jan 1, 2002

By L. A. Barta

A new process for the leaching of chalcopyrite concentrates has been developed and tested in miniplant campaigns and locked cycle testwork carried out between 1996 and 1999. The process involves pressure leaching in a sulphuric acid solution, e.g. raffinate from copper solvent extraction. Iron in the feeds is precipitated predominantly as hematite in the autoclave, simultaneously with copper extraction. Gold and silver in the pressure leach residue are recoverable by conventional cyanidation, following flotation to remove elemental sulphur by-product. The results of recent miniplant tests and batch locked cycle tests are provided.

Jan 1, 1999

By David B. George

In spite of the many well-known problems inherent in Pierce-Smith converting, it remains the dominant copper converting process. Continuous copper converting and direct concentrate to blister smelting have been commercially available for over 25 years and now produce approximately 15% of copper smelter production. The two fully commercialized continuous converting processes, Mitsubishi MI Process and Kennecott-Outokumpu Flash Converting, and several emerging converting processes are reviewed with view of their potential, limitations, and environmental performance. Some myths regarding these technologies and Peirce-Smith converting are also challenged.

Jan 1, 2002

By Arthur G. Hunt

Smelting using the direct-to-blister process commenced at Olympic Dam on 31 July 1988. The unique nature of the Olympic Dam ore body led to the selection of the direct to blister smelting process. Significant improvement in the design of the furnace and the understanding of the fundamentals of the process and its operation has occurred in the 10 years of operation. The paper will discuss the operation of the #1 Smelter and the design, preparation for start up and early operating experience of the #2 Smelter.

Jan 1, 1999