Search Documents

By Jeffrey W. Fergus, Shiqiang Hui

"Aluminum is an important alloying addition to the zinc used in the hot-dip galvanization of sheet steel to control the properties and appearance of the resulting coating. Optimization of the galvanization process requires control of the alloy concentration which can be improved through the use of chemical sensors. Aluminum sensors based on molten electrolytes are commercially available but are not widely used because of their high cost. One approach to reducing the cost is to use a solid electrolyte which can simplify the sensor design and thus reduce the cost of fabrication. In this paper, the development of an aluminum sensor based on a solid fluoride electrolyte, specifically magnesium fluoride, will be described.IntroductionThe concentration of the zinc bath used in hot-dip galvanization affects the galvanization process as well as the properties of the resulting coating. Thus, accurate in situ measurement of the alloy composition can be used to improve process control. This paper describes a solid-electrolyte-based aluminum sensor for monitoring the bath composition during hot-dip galvanization."

Jan 1, 1997

By Yuuki Yoshida

Electrolytic manganese dioxide, EMD, is the positive electrode material of primary batteries and the raw material of LMC used as the positive mass of lithium ion batteries and is currently produced by anodic deposition on and harvesting from a titanium anode in acidic manganese sulfate solutions prepared by dissolving high purity of manganese sulfate into sulfuric acid solutions. This paper presents an alternative method of EMD production using a novel anode, Mn2O3 coated titanium, at lower operating temperature than the current process to explore a possibility of manganese recovery from zinc electrowinning solutions. The Mn2O3/ Ti anode prepared by thermal decomposition of a precursor solution containing Mn (II) showed the anodic deposition of MnO2 by constant current electrolysis and the current efficiency was 95% in maximum, while the current efficiency and the crystallographic structure of deposited MnO2 depended on the current density, the electrolysis time, the bath temperature, and the concentration of Mn(II). The deposited MnO2 was successfully harvested from the anode and the recovery rate was 98%.

By Yoshihiko Maeda

It is said that the 21 st century will be an era of the remedy of the global environment. In order to reserve natural resources for the future and to avoid the dispersion of heavy metals after usage and to avoid pollution problems, it is extremely important to recycle heavy metals as much as possible by reasonable recovery procedures. The nonferrous metal industry is expected to play a important role in the recycling of heavy metals that are originally their products. From the depressed metal price experienced in Japan in 1980th due to the sudden change in current exchange rate between US dollar and Japanese yen, one of major nonferrous metal company, Dowa Mining, has diversified its business area not only to the so-called down stream, but also to the environmental business including metal recycling, industrial waste treatment and soil remediation by utilizing technologies and facilities once used or still used for mining and smelting of copper, zinc, lead and precious metals. In this paper some of these applications will be presented.

Jan 1, 2003

By Yoshihiko Maeda

It is said that the 21st century will be an era of the remedy of the global environment. In order to reserve natural resources for the future and to avoid the dispersion of heavy metals after usage and to avoid pollution problems, it is extremely important to recycle heavy metals as much as possible by reasonable recovery procedures. The nonferrous metal industry is expected to play a important role in the recycling of heavy metals that are originally their products. From the depressed metal price experienced in Japan in 1980'h due to the sudden change in current exchange rate between US dollar and Japanese yen, one of major nonferrous metal company, Dowa Mining, has diversified its business area not only to the so-called down stream, but also to the environmental business including metal recycling, industrial waste treatment and soil remediation by utilizing technologis and facilities once used or still used for mining and smelting of copper, zinc, lead and precious metals. In this paper some of these applications will be presented.

Jan 1, 2003

By Ramana. G. Reddy, Haoxing Yang

The electrodeposition of zinc from zinc oxide using urea and choline chloride mixture in a molar ratio 2:1 is investigated in different experimental variables, namely, the concentration of added [BMIM]HSO4, temperature, and applied cell voltage. The additive, [BMIM]HSO4, was determined to have beneficial effect on the current efficiency, energy consumed in the process and surface morphology of the deposits. The highest current efficiency (92.6%) and lowest energy consumption (2.92kWh/kg) was obtained for solution with 20mg/mL [BMIM]HSO4. The morphology showed the formation of absorbed additive layer on the cathode at higher concentration of additives. Experiments were conducted at different temperatures between 343K and 388K and at various applied cell voltages between 2.7V to 3.6V to determine the best experimental conditions. By varying temperature, highest current efficiency (91.3%) and lowest energy consumption (2.69 kWh/kg) was obtained at 373K. The electrodeposition process is enhanced between the applied voltage 3.0-3.3V by achieving lower energy consumption (2.75~3.06kWh/kg) and higher current efficiency (88.4~89.7%). SEM images showed grain size is significantly increased in higher applied voltages. While at higher temperatures, it seemed to generate particle growth as clusters at the outer deposit layer.

Jan 1, 2014

By Beatryz Mendes, Leonardo Pedroti, Afonso Azevedo, José Maria Carvalho

The dregs is a waste from the cellulose production, and its reuse is an effective way to reduce environmental impacts. Researches have already been done to incorporate it into building materials. The present work aimed at incorporating dregs in the production of mortar to replace hydrated lime. The methodology adopted was the Simplex network with ten sampling points, varying the amount of cement, sand, and dregs. Each mix was submitted to flexural strength, compressive strength, apparent mass density and water absorption by capillarity tests. The results were analyzed by the software Minitab, obtaining the influence of each component in the mixture. The best results were observed in mixes with a higher proportion of cement and less of residue when it was analyzed the flexural and compressive strengths. Larger rates of apparent mass density and water absorption were noticed with a greater amount of dregs. The experimental design also allowed the obtainment of mixture ratios from predetermined values of the tested properties and indicated that the addition of dregs in mortar could be an alternative to civil construction.

Mar 1, 2018

By Wenxian Zhu, Patrick R. Taylor

"The small dimensions of nano-sized materials leads to novel and enhanced mechanical and physical properties. A thermal plasma reactor has been developed to study the formation of nanometer sized metal powders. A supersonic nozzle and a powder filter were designed and built. By vaporizing coarse metal powders in the plasma flame, and quenching the metal vapors through the nozzle at the rate of 107 K/sec, nanometric sized powders have been produced. The powders were collected in an airtight secondary quench-filter system. The particle size of the product power is 5 -20 nanometers, obtained through TEM analysis. The XRD analysis showed that the powder did not oxidize after the filter was handled in an inert atmosphere glove box.IntroductionNanostructured materials have been shown to exhibit improved physical and mechanical properties compared to conventional materials with larger grain sizes (1,2). There have been several methods proposed for preparing nanometer size materials. Thermally induced vapor-phase reactions have been used to produce a variety of powders. A common feature of these processes is the rapid production and cooling of condensable reaction intermediates and products, by gas-phase reactions, leading to the formation of a large number of very small particles. Thermal plasma synthesis of ultra-fine size particles has been attracting increasing interest (3,4,9-11), because it offers many advantages, especially in refractory materials processing, compared to conventional processes: (a) thermal plasma temperatures are very high(> 5000 K); (b) the rates of chemical reaction are much faster than those encountered in conventional processes; (c) high-purity materials may be obtained using fewer processing steps by collecting the product at temperatures where the by-products are in the vapor phase; ( d) the mean particle diameter can be controlled; (e) unifom sized particles may be produced with clean surfaces (these particles are particularly suitable for pressureless sintering); and, (f) high throughput per reactor volume can be achieved. In addition, the process used for generating particles determines the degree of sintering ability of the powders, since the process dictates the morphologies, the purity and its size distribution. In the future, thermal plasma synthesis nanometer size particles may play an important role in vapor phase reaction techniques and might be expected to be one of the first full scale commercial installations in the future."

Jan 1, 1998

By M. Ashraf, P. J. Hazell, A. A. H. Ameri, J. P. Escobedo-Diaz, N. N. Elewa

A novel methodology to estimate the dislocation density in cubic metals by using microhardness measurements has been established. The proposed methodology is based on the Indention Size Effect (ISE) phenomena and strengthening mechanisms of materials at the micro-level. The methodology was validated by using experimental data of lean duplex stainless steel 2101 alloy. The results are confirmed via X-ray diffraction measurements and they substantiate that the proposed approach can be used as a general method to estimate dislocation density in metals.

Mar 1, 2017

By Won C. Park

Experiments showed changes in the mineral content of dolomitic oil shale at temperatures and exposure times which bracket conditions encountered during in situ retorting. Laboratory results correlate with cores from a spent in situ retort at Occidental's Logan Wash test site at Garfield County, Colorado. Dolomite, CaMg(CO3)2, decomposes rapidly to form periclase, MgO, calcite, CaCO3, and CO . Both calcite and periclase are intermediate products that can be stabilized by CO atmosphere at lower temperatures, while steam accelerates the formation 2 of silicates. The decarbonation of calcite appears to involve a direct reaction with both quartz and periclase in forming these silicates. Decarbonation preceeds the formation of akermanite, Ca2 MgSi 207, and diopside, CaMgSi 206, within several hours of heating and is followed by the nucleation of forsterite Mg2SiO4, and monticellite, CaMgSiO4. Under in situ retorting conditions, akermanite and diposide are the major minerals above 800°C. Equilibrium is not attained within 200-300 hours. In situ retorting temperatures above 800°C for extended periods of time should reduce potential ground water leaching by the formation of silicate minerals. These silicates are less soluble than free lime, magnesium or alkali oxides. There is a corresponding decrease in the natural pH of these silicates from approximately 12 down to 7.5 to 9:

Jan 1, 1981

By G. L. Fredrickson, T. A. Johnson, B. R. Westphal, J. C. Wass, S. X. Li, D. Vaden

"Recovery of uranium from the Mk-IV and Mk-V electrorefiner vessels containing a LiCl/KCl eutectic salt has been on-going during the pyrometallurgical processing of used nuclear fuel for 14 and 12 years, respectively. Although austenitic stainless steels are typically utilized for LiCl/KCl salt systems, the presence of cadmium in the Mk-IV electrorefiner dictates an alternate material. A 2.25Cr-1Mo alloy (ASME SA-387) was chosen due to the absence of nickel in the alloy which has a considerable solubility in cadmium. Using the transition metal impurities (iron, chromium, nickel, molybdenum, and manganese) in the electrorefined uranium products, an algorithm was developed to derive values for the contribution of the transition metals from the various input sources. Weight loss and corrosion rate data for the Mk-V electrorefiner vessel were then generated based on the transition metal impurities in the uranium products. To date, the corrosion rate of the 2.25Cr-1Mo alloy in LiCl/KCl eutectic is ""outstanding"" assuming uniform (i.e. non-localized) conditions.IntroductionLow-enriched uranium products are being recovered from the Experimental Breeder Reactor-II (EBR-II) and Fast Flux Test Facility (FFTF) used nuclear fuels by a pyrometallurgical treatment process at the Idaho National Laboratory (INL). The treatment process comprises a set of operations designed to neutralize bond sodium, recover uranium from radioactive fission products, and place the fission products into acceptable waste forms [1-2]. Reactive sodium metal, essential for heat transfer purposes during reactor operations, is readily converted to chloride during the process. Electrorefined uranium products are currently being stored pending a final disposition decision. Treatment of the EBR-II used driver fuel was initiated in June 1996 while blanket fuel processing started in September 1998. These treatment processes continue on the balance of the used fuels."

Jan 1, 2011

By S. Yuan

Oxygen ion conducting yttria-stabilized zirconia (YSZ) tube was used to remove oxygen from molten Cu at 1373K. Outer surface of the tube was in contact with the melt and the inner surface containing a thin layer of porous Ni-ZrO2 cermet electrode was in contact with a reducing gas. The migration of oxygen species (O2-) from the Cu melt through the YSZ tube is accompanied by an equal and opposite flux of electrons maintaining electroneutrality. Without applying an external EMF, the fluxes are maximized by short circuiting the melt with the cermet electrode. For efficient oxygen removal, the YSZ tube must be thin, contact resistances should be negligible, and the electrodes must be porous and cover the entire electrolyte surface for charge transfer. This refining process is environmentally sound, can use reducing gases such as H2, CH4 and CO without running the risk of increasing H or C content of the melt.

Jan 1, 1993

By Deming Wang, R. A. Overfelt

"This paper presents a computer-aided heat transfer simulation method to predict the thermal characteristics of an alloy sample in a special furnace for directional solidification. A two-dimensional transient heat transfer by conduction combined with radiation is developed to calculate the energy exchange between a directional solidification furnace and the sample. Finite difference equations with control volumes are used to calculate the transient heat transfer. A special boundary control volume is used to combine heat conduction and radiation in the transient heat transfer. Heat radiation effects on the surfaces of the special control volumes with a changeable view factor during directional solidification processing are also represented. The simulation results are verified by measurable experimental data. Using the computer simulation model, many thermal properties of the directional solidified castings can be obtained, such as temperature distribution, solidification velocity, the shapes and positions of the liquid/solid interface and thermal gradient at the interfaces. These are very important to analyze microstructure of casting alloys, avoid casting defects and control casting quality. 1 IntroductionIn directional solidification (DS) processing of castings, the temperature distribution, the interface between liquid and solid zone, thermal gradient in the mushy (pasty) zone and solidification rates are very important factors to analyze the microstructure and the casting quality. These variables affect the orientation and size of dendrites, shapes of grains, solute segregation and deleterious casting defects, such as microporosity, freckles and segregation channels. In order to avoid the casting defects, the temperature distribution and thermal gradients of castings during directional solidification must be strictly controlled. However, the structure of furnaces used for directional solidification is often complex. Heat transfer and temperature distribution within a casting not only depend on furnace temperature but also on the thermal properties of the casting alloy, crucibles, retorts etc. A more accurate heat transfer analysis."

Jan 1, 2001

By E. F. Vegman, Ndabezinhle Dube

"In the practice of conventional sintering, production is always afflicted with the problem of being unable to get a uniform quality of produced sinter in the bed. Invariably the top layer of the sinter cake is composed of weak but highly sinter, while the bottom layer is over-fused, forming a sinter that is very strong but less reducible. These symptoms point to a variable distribution of the heat balance in the process of sintering which results in a deficit of heat in the top layers of the sinter bed and an excess of heat in the bottom layers, due to an increasing input of regenerated heat in the heat balance down the bed. This causes losses in the productivities of the sinter machine and the blast furnace.The current work was designed to improve on the solution to the above problem through the establishment of a more accurate combustion zone heat balance of the sintering process. This development is mostly on the method of determining the regenerated heat input in the overall heat balance. Previous methods were based on the assumption that the width and the velocity of the combustion zone remain constant through out its whole life, which is not the case since tests have shown that both its width and velocity increase as the combustion zone moves down the bed. In this work, these factors have been taken into account. Tests and calculations using the model were carried out for haematite and limonitic ores. The high sensitivity of the model to changes in the sinter mix composition and sintering conditions was demonstrated.The results present the following prospects:• The minimum theoretically possible coke breeze consumption during the sintering of any type of iron ore fines, under any sintering conditions, can be established.• The model can be used to control the metallurgical quality of the sinter in any point in the sinter bed since calculation data includes desired basicity, combustion zone temperature and FeO content in the sinter produced."

Jan 1, 2001

By M. Tokumasu, T. Mutoh, Y. Sugawara

"In October 1986, a process computer was introduced in order to achieve an optimum combustion of pulverized coal at the reverberatory furnaces. The secondary combustion air volume is controlled based on the nitrogen oxide concentration of the off-gas from the reverberatory furnaces. The carbon monoxide concentration has strong relation with the concentration of nitrogen oxide under the situation of using alternative fuels, such as chipped tires and p,ulverized coal. Using this computer aided combustion control system, both nitrogen oxide and carbon monoxide concentrations were stabilized and conventional monitoring and controlling apparatuses were absorbed into this computer system. Due to this easily operated system, labor cost was reduced and the operation of the reverberatory furnaces and the off-gas treatment plant became stable.IntroductionOnahama Smelter and Refinery started its operation in April 1965 as a large scale copper smelter and refinery in Japan. The green charged reverberatory furnaces were introduced and bunker C oil was chosen as the fuel for the reverberatory furnaces. After the oil crises, Onahama was forced to use cheaper fuels such as coal and waste tires, i.e., alternative fuels instead of the expensive oil. As the amount of the alternative fuels fed to the reverberatory furnaces increased, the concentrations of nitrogen oxide and carbon monoxide in the off-gas became unstable. Consequently, the fluctuation of the combustion condition became not to be negligible in view point of a combustion efficiency and pollution regulations. A process computer has been introduced to overcome these off-gas troubles and to reduce the operating cost of the smelter.Outline of Operation HistoryInitially, the operation started by one reverberatory furnace and then the capacity was expanded almost twice by additional furnace in December 1972. As shown in Figure I, the smelting throughput was depressed after oil crises in 1973 and 1978. From 1983 to 1985, some copper mines stopped their operations because of low price of copper metal. During this period, Onahama suffered from the shortage of concentrate production levels were depressed."

Jan 1, 1989

By Cong Wang, Kexin Jiao, Yongan Zhao, Haibin Zuo, Jianliang Zhang

Traditional refractory materials for blast furnace hearth lining are mainly composed of carbon bricks and the ceramic cup. However, these materials can’t meet the demands for long service life design of blast furnaces. In this paper, a new refractory called carbon composite brick (CCB) was introduced, which combined the advantages of carbon bricks and the ceramic cup. In this case, the resistance of the CCB against corrosion was equal to the ceramic cup and the thermal conductivity of the CCB was equal to carbon bricks. From the results of more than 20 blast furnaces, the CCB could be well used in small blast furnaces and large blast furnaces. In the bad condition of low grade burden and high smelting intensity, the CCB gave full play to the role of cooling system, and effectively resisted the erosion of hot metal to improve the service life of blast furnaces.

Jan 1, 2015

By P. Meyers, F. DeSilva, L. Gottlieb

A number of tests looking at lead removal using ion exchange resins of various types from various aqueous streams have been undertaken. The tests focused on strong acid cation (SAC) and weak acid cation 0N AC) resins. It was found that the mechanism of lead removal is partly by lead filtration rather than solely by ion exchange in a large portion of the applications studied. This is not surprising since lead carbonate is essentially insoluble and almost all water supplies contain at least some carbonate alkalinity. Regeneration of lead from exhausted resins containing significant amounts of lead may not be practical in some cases because of the large chemical and waste volumes involved. Since lead, .·along with many other very insoluble metals, is often present as a suspended solid rather than in ionic form, ion exchange is probably not always the best technology for bulk lead removal.

Jan 1, 2000

By Heinz Giegerich

This paper deals with a new development in recycling second generation catalytic converters, namely metal substrate converters (MSC). It describes a patented dismantling process, whereby the MSC is segregated into it's three components outer steel shell, metal substrate carrier foil and ceramic W8shcoat with embedded precious metals.

Jan 1, 1995

By Wilson Pascheto

This paper presents results of investigations performed as part of a Root-Cause-Failure-Analysis (RCFA) of a DC smelting furnace that was brick lined with MgO-based refractories. An unusual continuous contraction of the furnace hearth was identified during operation. Cracks in the refractories were envisaged after a major shutdown of the furnace. To determine the mechanism and causes of the unusual contraction behaviour of the furnace hearth, refractory samples were taken from the furnace at different locations and subjected to different analysis including Scanning Electron Microscopy (SEM), Energy-dispersive X-ray spectroscopy (EDX), QEMSCAN and Electron Probe Micro Analysis (EPMA). Creep testing of refractories under different loads (ASTM C832) was also employed to evaluate the mechanical integrity of the used bricks in comparison with the new ones. Results of the various characterisation analyses revealed that there was an interaction between refractory bricks and molten material during furnace operation, which resulted in reduced creep resistance of the MgO-based refractories. This was verified by comparing creep performance of the used brick samples and new brick samples at different temperatures and applied stresses.

By John Anawati

Bauxite residue is an environmentally unfriendly byproduct of alumina manufacturing, produced worldwide in large quantities. This material contains 50– 100 ppm of scandium, a critical material for the production of stronger, weldable, corrosion resistant, and heat tolerant aluminum products. Aircraft manufacturers are particularly interested in Al–Sc alloys because of its ability to form weldable alloys that could potentially reduce aircraft weight by 15–20%. Because of its abundance and low cost, bauxite residue has the potential to be used as an efficient feedstock for valorization processes to recover its scandium content, while in turn degrading this problematic waste. In this project, we developed an efficient process to recover scandium and rare earth elements from a Canadian bauxite residue with high extraction yields, using industrially scalable and economical techniques. The process employs a modified version of sulfuric acid leaching and subsequent impurity removal by selective precipitation. This article outlines the current progress and design rationale in the development and optimization of this innovative and sustainable recovery process.

By Shengqin Zhang, Yousef Mohassab, Feng Chen, Hong Yong Sohn, Mohamed Elzohiery, Amr Abdelghany

A novel ironmaking process is under development at the University of Utah aimed at producing iron directly from iron oxide concentrate in a flash reactor. This process will reduce hazardous emissions and save energy. The kinetics of magnetite reduction with hydrogen was previously investigated in our laboratory in the temperature range 1150 to 1400 oC at large temperature increments (~100 oC increments). Due to the significant melting that occurs above 1350 oC, the reduction kinetics was measured and analyzed in two distinct temperature ranges of 1150 to 1350 oC and 1350 to 1600 oC (~50 oC increments). Experiments were performed using magnetite concentrate particles of different sizes under various hydrogen partial pressures and residence times. Reduction degrees of more than 90 % were achieved in a few seconds at temperatures as low as 1250 ºC. Different rate expressions were needed to obtain reliable agreement with experimental data.

Jan 1, 2016