Search Documents

By D. Nozadze

A new method of isothermal electro-contact diffusion welding of layered composites under pressure is offered. The scheme is developed and laboratory installation is created on which preproduction models of the layered composite of steel and aluminum is produced. A new method of electro-contact hot deformation is proposed for realization of diffusion welding by pressure of stratified blanks providing high-temperature isothermal process. In this case a rolling process or composite pressing is meshed with simultaneous electric current transmission in deformation center. Considering that a resistance of transient layer far exceeds the resistances of composite components, the heat release takes place intensively just in this layer. As the surfaces are approached over a distance of inter-atomic forces, the energy of boundary atoms easily reaches the energy threshold of capture with a formation of qualitatively new metallic bond. Proposed method, providing isothermal process in deformation center, excludes a necessity of previous preparation and prevention of surfaces. In this case strength of layer connection may approximate or exceed strength limit of cladding layer.

Jan 1, 2006

By Tsembel Darjaa, Toru H. Okabe, Yoshiaki Umetsu

"With the purpose of extracting molybdenum and rhenium from molybdenum sulfide concentrate; .electrolysis of slurry, solvent extraction and ·precipitation operations were carried out. The slurry of the concentrate in 10 mass% NaCl aqueous solution was continuously circulated into a vertical type 10 stack bipolar electrolytic cell consisted of carbon electrode disks, and, the concentrate was dissolved by electrochemically generated oxidizers at 313 K. The current efficiency for molybdenum dissolution was 73 % after 10 hours electrolysis, and the leach solution was found to contain 0.2 mol/l of molybdenum and 4x10-5 mol/l rhenium. This result shows the dissolution is more than 8 times faster than that obtained using a single cell. The leach solution from electro-oxidation was then subjected to a solvent extraction for rhenium which is then recovered as sulfides. After rhenium separation, molybdenum was precipitated by pH adjustment, and solid MoO3 (H2O)x crystals, free of sulfate, were obtained from the leach solution containing large amount of so42-.IntroductionIn the past, electro-oxidation using a bipolar cell was applied for leaching molybdenite concentrate and ores at U. S. Bureau of Mines [1-3] and also at Bhabha Atomic Research Center [4]. In· these previous studies, Moebious type bipolar cells, in which electrode plates were vertically inserted into the free surface of the electrolyte, were employed and its effectiveness was demonstrated.Recently, the present authors studied on leaching of Mongolian molybdenite concentrate, and the effectiveness of leaching of the concentrate by electro-oxidation in alkaline and acidic NaCl solutions was demonstrated [5]. The leaching reaction during the process can be explained by the 18 electron transfer reaction of molybdenite (MoS2) with the oxidizers produced in-situ by electrolysis of NaCl aqueous solution. Further investigation was made with respect to various process parameters for electrooxidation such as pH, pulp density and temperature of the slurry, and the dissolution behavior of minor elements such as iron, copper, and rhenium [6]. Solubilities of molybdenum in the leach solution at, various temperatures and pH .was · studied, and feasibility of molybdenum recovery by hydrolysis of molybdenum species was demonstrated. By adjusting the pH of the leach solution, molybdenum oxides or hydroxides free from sulfate were successfully obtained from the solution containing large amount of sulfate ion. Rhenium present in the concentrate at a level of several tens of mass ppm was found to dissolve into the leach solution, and co-precipitate with the molybdenum compounds. Rhenium in the leach solutions, therefore, has to be recovered before precipitation of molybdenum, otherwise it is lost in the precipitate."

Jan 1, 2000

By A. V. Reddy, C. Beckermann

"The DC continuous casting of a grain refined AI-4.5%Cu round ingot with realistic boundary conditions is numerically simulated. Of particular interest are the effects of the transport of free solid in the form of equiaxed grains on the macro segregation patterns and the final grain size distribution. The study uses a previously developed two-phase model that incorporates descriptions of heat transfer, solute redistribution, melt convection, and solid transport on the system scale with microscopic models of solutal undercooling, microsegregation and grain impingement. The numerical results indicate that grain transport inhibits the formation of inverse segregation in the ingot shell and promotes negative centerline segregation. This is explained by the reduction in the solid coherency next to the mold and the advection of solute-lean grains towards the centerline. Comparisons with the experiments of Finn et al. [5] illustrate the need for considerable improvements in the model. IntroductionMacrosegregation continues to be one of the concerns in DC continuous casting of aluminum ingots. The variation in composition over the ingot cross section results in the need to adjust alloy composition in order to meet mechanical property specifications in finished products. The extent of macrosegregation is greatly affected by the casting conditions, such as casting speed, superheat, cooling rate, mold size, alloy composition, and grain refining practices. Thus, it is of great interest to develop a comprehensive mathematical model to simulate the casting process, enabling the selection of conditions that minimize macrosegregation while maintaining a high productivity."

Jan 1, 1994

By F. Robert Hubbard

IMCO Recycling Inc. has developed a new, patented technology for the production of fertilizer, K-SOIL?, as a by-product of its aluminum recycling operations. This new technology can substitute for conventional technology which now results in a saltcake residue that is placed in 'landfills. Four years of research and development work by IMCO culminated in a U. S. patent issued April 5, 1994. As part of the technology development effort, IMCO engaged the services of a nationally renowned research organization and a prominent university. These two organizations have conducted in-depth agronomy studies In the laboratory, greenhouse, and the field. Results have shown K-SOIL? to be performance equivalent, on a nutrient content basis, to conventional potash fertilizer. The first field applications on commercial farms were made in the spring of 1994. K-SOIL? is a potassium-bearIng, granular solid which may find use in fertilizer blends, direct application, and other forms of fertilizer products. The overall benefit of this new technology is to create a useful by-product rather than generate a useless residue and, thereby, reduce or eliminate the amount of salt cake now placed in landfills. As such, It is a significant, step toward IMCO's ultimate goal of complete recycle.

Jan 1, 1995

By Shenghui Guo, Dongbo Li, Lijun Liu, Chengdong He, Jinhui Peng, Libo Zhang

In present study, partially stabilized zirconia (PSZ) was prepared by CaO doped fused zirconia heated by microwave furnace at the temperature of 1450 oC and holding time of 120 min. The XRD results showed that untreated fused zirconia mainly consists of crystalline compounds of cubic ZrO2 phase; while the roasted one mainly is composed of crystalline compounds of cubic ZrO2 phase and monoclinic ZrO2 phase. It is shown through the optimization of structures of two phases that structure of cubic ZrO2 and monoclinic ZrO2 reject each other, revealing its difficulty in forming coinciding interface and linkage of two phases being of Ca atom. Introduction Due to advantages of zirconia, such as high melting point, chemistry inertia, low heat transmission and so on. Zirconia is always taken as megathermal refractory material[1]. However, in the heating and cooling processes of pure zirconium oxide, martensitic transformation will take place associated with greater shear force and volume change, which severely limits the industrial application of pure zirconia in some areas. Such as: Refractory materials, grinding materials and high temperature insulation materials[2]. Through adding a certain amount of MgO, CaO, or Y2O3 stabilizer, etc.[3,4], the zirconia can change into fully stabilized zirconia, which exists in cubic phase. But this high purity fully stabilized zirconia cracks easily because of thermal stress. Therefore, the thermal shock resistance variation is one of the most important quality indicators of zirconia-based materials. According to the heat treatment, the fully stabilized zirconia can be changed into the partially stabilized zirconia (PSZ)[5], which exists in cubic phase and monoclinic phase and has superior mechanical properties, such as anti-heat, low thermal conductivity, large coefficient of thermal expansion and stability, as well as good wear resistance[6].

Jan 1, 2011

By D. M. Hausen

Applications of process mineralogy to the exploitation of molybdenum ores begins with early exploration and continues through the evaluation of mineralized prospects, to amenability testwork and pilot plant studies, to the development of a mineable orebody and to the development of a viable process for recovery. After plant construction, a broad range of products from a wide selection of sampling locations, i.e. grinding circuit, flotation cells, smelters and roasting kilns. etc., are evaluated analytically and microscopically, followed by periodic troubleshooting of problem points. The various crystalline phases of molybdenum that occur naturally and throughout various hydrometallurgical and pyrometal1urgica1 processes are identified and characterized by a variety of instrumental methods, including XRD-XRF, optical and electron microscopy, infrared spectrographic and differential thermal analysis.

Jan 1, 1989

By A. E. Wraith

The tuyère flow rates of Peirce-Smith converters and bath smelting reactors are rendered particularly sensitive to accretion formation, bath depth variations and the general aerodynamic design of the blast delivery system by the limited pressure-flow properties of the conventional single stage centrifugal blower. This sensitivity is examined in terms of tuyère practice, vessel management and fixed engineering parameters for Peirce-Smith converters and the Noranda Reactor by use of the flow resistance factor, R*. New understanding of the effect of accretion growth on the flow behaviour of individual tuyères shows that blowing rates and hence throughputs could be optimised by careful attention to operating detail even within present plant constraints. The concept of the resistance vector is introduced to elucidate comparisons between different practices and to provide reference standards for optimisation. On this basis, the benefits of introducing quite moderate changes in the pressure-flow properties of the blast delivery system are considered. In view of recent developments in the flexible use of converters as hybrid bath smelting vessels for matte production, the foundation is now laid for a searching consideration of relationships between vessel volume and shape, blowing requirements, tuyère performance and production rates, the detail of which will be examined more appropriately in a forthcoming paper.

Jan 1, 1999

By Roberto Parra

The classic criteria of the preparation of the charge for the smelting of copper concentrates in at flash furnace considers the mass and energy balance from the chemical and mineralogy composition of the concentrates. The operation parameters fixed with this method don't assure the stability of the operation and the critical problems of the slag quality and dust formation occurs very often. This paper presents the results of a laboratory test that allows the prediction of the behavior of concentrates blends in the view of the minimization of the dust formation and the magnetite control in the slag. The combustion of different copper concentrates and blends were done in a drop tube furnace The results show that the magnetite and dust formation don't have a linear behavior with the weight proportion of the blend and some optimal blends of 2 or 3 types of concentrates can be identified. From the reasonable hypothesis that the qualitative behavior of blends in the drop tube represents the real behavior in the burner, the preparation of the charge with this approach could help to solve those operational problems.

Jan 1, 2003

By C. Burton Clark

The important role of the petrographic microscope in the petrology of refractories is discussed, based on 45 years of industrial experience by the author. Highlights of his career are used to illustrate improvements in equipment and techniques during the period. Two specific investigations are described which emphasize the interrelated use of the petrographic microscope with other instruments such as the x-ray diffractometer and scanning electron microscope. Emphasis is placed on the use of phase equilibrium diagrams for guidance in predicting and interpreting reactions that occur under non-equilibrium conditions in the manufacture and use of refractories.

Jan 1, 1982

By G. G. Krishna Murthy

Several experiments were conducted to determine the rates of heat transfer coefficients of CaO-SiO2-A1203-FeO slags at temperatures in the range 1623-1823 K The experimental technique involved measuring heating rates of a solid specimen, sub¬merged in slag phase, using a temperature probe made of Pt\ 10%Rh-Pt. Effect of %FeO (3-10%), %FeS (0.1-0.68%), %P205 (0.2-3.0%), %MgO(5-6%), and %MnO (0.96-3.84%) present in the slag on overall heat transfer coefficient, U, of slags was investigated. Simple first order heat balance equation in combination with experimental plots rising temperature of solid specimen versus time were employed to determine the values of U. The values of U determined in the present investigation were present in the range of 70-260 cal/Ks.m2. The value of U increased with increasing the slag temperature. The values of U were not effected by increased amounts of sulfur in the slag phase. The increased concentrations of MgO, FeO, MnO, and P205 in the slag phase decreased the values of U. On the other hand, the increased amounts of Fe2O3 in the slag phase increased the value of U. Comparison of the results, obtained using the slag bath stirred by argon injection, with those determined without any stirring indicated that both radiative and conductive heat transfer mechanisms are important even at high temperatures.

Jan 1, 1993

By Yiling Zhang, Paul A. Salvador, Gregory S. Rohrer

"Photocatalysis utilizes solar energy to produce hydrogen by splitting H2O. When a thin film of photocatalyst TiO2 is supported on a ferroelectric BiFeO3 substrate (band gap ~2.5 eV), the TiO2/BiFeO3 heterostructure is capable of photochemically reducing Ag+ to Ag0 in aqueous solutions under blue light with enhanced efficiency. The observation of spatially selective silver patterns on surface of the heterostructure after reaction suggests that photogenerated electrons and holes in ferroelectric BiFeO3 are driven in opposite directions to reduce their chance of recombination. Comparisons of the amounts of reduced silver on TiO2 film grains with distinct phases/orientations show that the reactivity is mildly preferential on anatase TiO2 phase and does not strongly depend on crystallographic orientation of BiFeO3.IntroductionTitania (TiO2) is capable of photocatalytically converting H2O to hydrogen and oxygen under the irradiation of ultraviolet light. [1, 2] One of the limiting factors for titania to be used as an effective photocatalyst is its band gap. Because the absorption edges of rutile and anatase titania are at 3.0 eV and 3.2 eV, respectively, they can only absorb light in the UV portion of the spectrum, which is about 3% of the available solar energy. [3-5] This limitation has motivated attempts to modify the absorption edge of titania so that it can absorb visible light.One strategy is to substitute a portion of the titanium and/or the oxygen with other atoms. There are numerous reports on visible light absorption of titania by doping and co-doping of Cr, V, Mo, Sb, Fe, N, S, C, and F. [6-34] Another strategy is to add an adsorbed molecular species that absorb visible light and donate an electron or hole to the titania, such as organic dyes [33, 35, 36] and Ce3+/Ce4+. [37, 38]The strategy in the present work takes the approach of depositing a pure titania thin film on a visible light absorbing substrate BiFeO3 to induce visible light activity of the heterostructure. BiFeO3 is a semiconductor with a band gap of about 2.5 eV [39-41] and is photocatalytically active in visible light. [42, 43] It is also ferroelectric with spontaneous polarization along pseudo-cubic <111> directions of 6.1 µC cm-2. [44] The spontaneous polarization gives rise to internal electric fields that drive photogenerated charge carriers, namely electrons and holes, in opposite directions to reduce their chance of recombination. [45-47] Additionally, the separation of electrons and holes leads to the spatial separation of reduction and oxidation half reactions so that the back reaction of intermediates is also suppressed. Such charge carrier separation has been reported in TiO2/BaTiO3 heterostructures with UV light illumination. [48-51] The TiO2/BiFeO3 heterostructures in this work combine both advantages of the relatively narrow band gap and the internal fields in BiFeO3 to enhance the overall photocatalytic activity."

Jan 1, 2014

By Kelly J. Driscoll

Impure zinc (98.5%) was electrorefined to high purity zinc (99.995%) using a fused salt electrolyte of molar composition 1: 1 : 1 :2 ZnCI2:KCl:NaCl:LiCl with a current efficiency of about 90% at 723 K. A recessed channel electrorefining cell was developed which achieved excellent mixing of both the metal and the electrolyte and by ensuring a very small anode to cathode spacing the voltage drop across the cell was 0.16 V and at a current density of 7kA m-2. The physical characteristics of the cell were observed using a low temperature model which showed the formation of droplets and rivulets which provided mixing. The application of this approach to the refining of other non-ferrous metals is discussed.

Jan 1, 1992

By David J. Roha

"The harsh environment of the Carbothermic Aluminum process makes necessary numerical modeling as a means of process visualization and understanding. A brief survey of the various numerical models, with emphasis on CFD, applied in the development of the process is presented.IntroductionThe environment of the Alcoa Carbothermic reactor is necessarily a harsh one, with temperatures approaching 2100 °C and plenty of reactive dust and vapors. As such, it is difficult to directly observe what is actually taking place. Thermocouples can last for a few minutes but are eventually destroyed. The openings to optical pyrometers become occluded with dust and condensation. Graphite sheathing embrittles, reacts away or becomes clogged with condensate. Dip-samples on steel rods are routinely taken, but their interpretation is often unclear.Those measurements that can be reliably taken are invaluable, but often do not provide a complete picture. Therefore from the very inception of the project both physical and computer based models have played an important role. Modeling provides an intuitive understanding of the processes that might be taking place and in very many cases approach quantitative prediction. I will briefly touch upon computer-based modeling performed at Alcoa over 12 years of the Carbothermic project, with special emphasis on CFD. The explanation of physical models is perhaps best left for those with the greatest familiarity with them"

Jan 1, 2012

By Nicole de Jager, Michael J. Nicol

"In order to liberate gold from refractory gold ores and concentrates it is generally necessary to oxidise the surrounding sulphide minerals, typically pyrite and arsenopyrite. Traditional methods of oxidation include pressure leaching, roasting and bacterial oxidation. In recent years, bacterial and pressure oxidation have found increasing favour, although these methods are by no means completely satisfactory and each is subject to particular disadvantages.A novel process has been developed as an alternative to the traditional methods whereby electro-generated ferrate(VI) ions in alkaline solution are used to oxidise a pyrite concentrate. This process has been observed to proceed fairly rapidly and could prove to be a more economically viable process, as well as being more environmentally acceptable. As an added benefit, operating in an alkaline environment is advantageous for downstream cyanidation processes.Ferrate(VI) is a relatively unknown species, due mainly to its instability in acidic solutions. However, in alkaline solution it has been observed to be sufficiently stable for use as an oxidant when used under favourable conditions. Ferrate(VI) is most conveniently manufactured electrolytically via the dissolution of high-carbon anodes in strongly alkaline solutions. Some literature has been published on the electrolytic generation of ferrate(VI) and relatively high efficiencies have been observed by both the authors and other researchers.This study utilises both electrochemical techniques and leaching experiments to examine the kinetics of the oxidation of pyrite by ferrate(VI), which is produced electrolytically. Cyclic voltammetry, rotating disk voltammetry and potential step experiments have been used to investigate the kinetics and mechanism of the oxidation process."

Jan 1, 1997

By Zhihe Dou, Zimu Zhang, Guozhi Lv, Yan Liu, Xiaoli Jiang

"Cyclic heat stewed slag washing water carries high content of alkali and calcium and may cause serious tube scaling and impose an adverse impact on normal production. This study proposes a solution to utilize washing water by absorbing and mineralizing CO2, potentially restraining scaling and being able to create calcium carbonate powders. Effects of water flux on water quality, utilization ratio of CO2 and yield of calcium carbonate powder have been investigated; meanwhile, features of calcium carbonate powder are also represented. On the other hand, effects of factors such as as injection flux, pressure of CO2 on utilization ratio of CO2, morphology and purity of calcium carbonate are also investigated. The results show unambiguously that after soften injection of CO2, calcium ions were removed effectively via precipitation, alleviating the scaling problem. High purity yet fine carbonate powder could be achieved.IntroductionNowadays, 0.34 tons of blast furnace slags will be produced when producing 1 ton of pig iron; ensuing that, 0.12 tons of steel slag will be generated with 1 ton steel production while 1.57 billion tons of steel output all over the world in the year of 2012. It is therefore a critical issue to realize zero discharge of steel slags to achieve sustainable development and cyclic economy of iron and steel industry. In recent years, research institute of MCC and China JINGYE engineering company developed a heat stewed steel slag self-decomposition technology GENERATION III to solve the problem of instability of steel slags and realize the zero discharge. However, the problem of circulation line scaling which may cause the clogging, even exploding, need to be solved. The principles of the technology are: directly spraying water to the high temperature steel slag when it is poured into the hot closed pot, realizing the selfdecomposition via utilizing the waste heat of steel slag. The washing water is recycled to achieve a cyclic utilization. The process is shown in Figure 1."

Jan 1, 2014

By John Demol

Monazite, a rare earth and thorium phosphate mineral, is one of the major minerals processed for extraction of rare earths. Industry practice for treating monazite concentrates is to use either a sulfuric acid bake or caustic conversion route. In the sulfuric acid bake, monazite concentrate is mixed with concentrated sulfuric acid and roasted. The rare earth phosphate mineral is converted to rare earth sulfate which dissolves in a subsequent water leach. As the bake temperature increases above 300 °C, thorium becomes less soluble. Although acid baking is practised in industry, the bake reactions are not well understood. A combination of chemical analysis, XRD and SEM-EDS was used to identify reaction processes occurring during sulfuric acid baking of a 93 wt% monazite concentrate between 200 °C and 800 °C. The effects of these reactions on the leachability of the rare earths, thorium and phosphate were also examined.

By S. Y. Tan

The thermal stability of fully silicided NiSi with arsenic doping on silicon was investigated. The aims of the work were to investigate the Ni silicide phase-related issues associated with arsenic dopant and thermal annealing on Ni-FUSI/HfO2/Si and Ni-FUSI/HfSiO/Si gate stacks. It was found that arsenic-incorporation demonstrated some improvement in both morphology and phase stability of nickel silicided films at high processing temperatures regardless underlying gate dielectrics. The correlations of Ni-Si phase transformation and arsenic doapnt with their electrical and physical changes were established by sheet resistance measurements, X-ray diffraction (XRD), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS) analysis. Furthermore, the modulation of the work function (WF) of Ni fully silicided gates by arsenic impurity is presented, comparing the effects of dopant (As) on the WF and silicide phases (NiSi and NiSi2). It confirmed that the work function of NiSi can be tuned by implanting arsenic dopant, but it ineffective for NiSi2 phase.

Jan 1, 2010

By Pekka Taskinen

The converter-less nickel matte smelting technology (DON) adopted more than 20 years ago in Boliden Harjavalta smelter has been since that applied successfully to the processing of large number of nickel sulphide concentrates of various Ni-to-Cu ratios and MgO contents. The operational point of the technology is far from the conventional primary nickel smelting in the smelting-converting route. Therefore, a careful scouting of distribution equilibria of the base and trace elements in the smelting conditions of DON process has been conducted, in order to obtain quantitative information about the equilibria and thermodynamic properties of the nickel mattes at low iron concentrations, less than 10 wt% [Fe] in matte. The series of investigations has included novel experimental and analytical techniques for increasing the reliability and sensitivity of the phase equilibria as well as the element distribution observations carried out in typical high-grade nickel matte smelting conditions.

By Herbert H. Kellogg

A model of the ISF is described. which reproduces with accuracy the "normal" operation of three industrial furnaces. The model, written in Fortran, is based on detailed heat and material balances, and the concept that the ascending gases reach equilibrium with zinc oxide and with the water-gas shift reaction. "Solution loss" of carbon in the lower shaft, and partial reoxidation of zinc vapor in the upper shaft are also essential features. For prediction of furnace behavior under altered operating conditions (blast rate, temperature, moisture content, oxygen enrichment, or injection of oil or coal through the tuyeres) the model modifies the heat loss, temperature of slag and bullion, amount of reoxidation in the upper shaft and the condenser efficiency to reflect the altered operating parameters. Model predictions for such operating conditions are in reasonable agreement with plant experience.

Jan 1, 1990

By Gerald K. Vellente

Producers of strip coated products are being approached by users to supply higher quality products and adhere to tighter specifications. Suppliers, in an attempt to assist the producers, must consider new technologies for equipment. In the past several years, the induction melting and heating industry has made great strides in developing new and innovative equipment, while improving existing technology. In the past several years, the induction melting and heating industry has made great strides in developing new and innovative equipment, while improving existing technology. In the past several years, the induction melting and heating industry has made great strides in developing new and innovative equipment, while improving existing technology. This paper will review recent developments to include improved refractory systems for ceramic pots, new channel-type inductors which are more efficient, new power control systems for existing channel-type pots, and innovative use of multi-purpose lines. Additionally, new heating applications such as galvannealing, edge heating, and post heating will be reviewed. Advanced math models for controlling heat will be discussed. Producers can easily meet the demands of their customers because of the flexibility provided by the equipment reviewed.

Jan 1, 1992