Search Documents

By W. F. Ranson, R. C. Progelhof

"I. THE PROBLEM: MANUFACTURING PRODUCTIVITYThe 1985 President's Commission [I] on Industrial Competitiveness found compelling evidence of the declining economic position of the United States in world markets. The annual rate of increase in the United States productivity is approximately one-seventh that of our major trading partners over the last decade: profit levels in manufacturing investments are below those of the mid-1960's; an increasingly negative trade balance since 1971; and a sharp decline in the United States share of world trade in manufactured goods for more than two decades. A particularly dramatic example of the shifting economic balance is the fact that Japanese productivity growth has been five times greater than that of this country since 1960. In face, Japan's productivity now exceeds that of the United States in such critical industries as steel, transportation equipment, electronics and electrical machinery.American employees have experienced the competitive consequences of this nation's lagging industrial performance. Between 1980 and 1984 alone, the population of non-farm employees engaged in manufacturing dropped from 22.4% to 20.6%. This reduction in manufacturing must be arrested.Commissions RecommendationsThe comprehensive set of recommendations offered by the President's Commission recognized the nation's ""key competitive advantages"", technology and human resources, and calls for their strengthening. Particular emphasis is placed on manufacturing technology and the fact that this country does not translate research into new technologies rapidly and fully.""Perhaps the most glaring deficiency in America's technological capabilities has been our failure to devote enough attention to manufacturing or 'process' technology. It does us little good to design state-of-the-art products if within a short time our foreign competitors can manufacture them more cheaply. The United States has failed to apply its own technologies to manufacturing. Robotics automation and statistical quality control were all first developed in the United States but in recent years they have been more effectively applied elsewhere""."

Jan 1, 1988

By George Kachaniwsky

Until mid-1982 the Mines Gaspe copper smelter consisted of a fluid bed roaster, a reverberatory furnace, two Peirce-Smith converters of which only one was blowing at any one time, anode casting facilities, and a single contact sulphuric acid plant treating both roaster and converter gases. Reduced concentrate supplies have led to the shutdown of the roaster and, as a result, it was necessary to adapt the converter and acid plant operation to the new operating mode: green concentrate smelting with resulting lower matte grades and acid plant treatment of off-gases from only one blowing converter. Therefore, modifications were carried out to existing equipment and methods of operation and control. This paper describes the result of work done to obtain steady, maximum strength, converter off-gas flow and an efficient acid plant operation. Topics covered include: optimization of converter operation, tightness of hood and off-gas ducting, improvements in acid plant/converter communications and modifications of acid plant operation and control to cope with the fluctuations in converter gas flowrates and strengths.

Jan 1, 1983

By Takeshi Nagano

Copper pyrometallurgy in Japan has experienced quite fundamental changes in last fifteen years. The severe environmental restriction coupled with increase of energy costs accelerated the development work of the new continuous process in Mitsubishi Metal Corporation. After several years of pilot plant test work the commercial plant was put into operation at Naoshima Smelter in 1974, the design capacity of which was 4,000 tonnes of copper per month. Many modifications and improvements have been incorporated into the process and 7,200 tonnes per month of copper production was achieved in 1983, proving that continuous process was much more economical than conventional process. It is now possible to design and operate the continuous process in wide range of capacity. This paper will review the process and describe the progress of the process in these 10 years. 311

Jan 1, 1985

By Robert E. (Bob) Brown

Magnesium was discovered by Davy in 1808. The production processes as they exist are not economically competitive with aluminum The electrolytic magnesium process is divided into two steps; one to make the MgCh feed and the other to apply large amounts of electric current to dissociate the feed into magnesium (450 g) and chlorine (1200 g). The production of fuJIy anhydrous, pure cell feed is a major problem Recently, there has been a growth of thermal processes, mainly the Pidgeon silicothermic production process using FeSi to reduce dolomite in horizontal retorts. Pechiney has a large vertical electrical furnace process that also uses FeSi to reduce calcined dolomite in a molten bath containing alumina. Work is proceeding to develop new or modified processes that will greatly improve magnesium production. The present methods and the research and R&D will be reviewed in this paper.

Jan 1, 2001

By B. C. F1intoff, R. G. Bradburn, E. Groiss

"The concentrator at Brenda Mines Ltd. treats a copper - molybdenum porphyry ore with current head grades of 0.185% Cu and 0.036% Mo. The consistently low head grades provided the driving force to explore methods of improving plant productivity. Computer based process control was recognized as one means of addressing this objective. Over the period from 1974 to 1982 a control system evolved which now extends to every area of the mill. Control strategies are built on elements of classical, modern and rudimentary expert control. In addition, the control system has often served as a catalyst for other technological developments. The economic returns associated with the system are very significant and it has played an important role in the mine's survival in times of poor metal markets. This paper presents an overview of the computer control system at Brenda.PreambleOne can scarcely avoid picking up a trade magazine or newspaper today without seeing some reference to technology and its potential impact on North American business. _A recurring theme is the need to apply technology to raise our standard of plant automation in the manufacturing and process industries. The general thesis of these articles has been concisely captured in the mutually exclusive set:AUTOMATE or EMIGRATE or EVAPORATEProcess control is one form of automation that has been successfully exploited by various sectors of these industries. In minerals and metal processing the wide scale adoption of process control technology has, until recently, been largely limited to a few companies - most of whom have a history in the area dating back to the early 1970’s. However, there is definitely an increased and much broader interest in process control as a technology which can improve performance, productivity and profit.The economic hardships that were visited on the mining industry in the early 1980's are not easily forgotten. It is the authors' conviction that the mining industry must move to implement proven technology, in particular process control, in order to be well postured for the next (inevitable) down cycle.In pursuing the technical and trade literature, one can discover a number of example of the successful utilization of process control systems in mining and related applications. In the text which follows, the authors describe the process control efforts undertaken in the Brenda Mines Ltd. concentrator."

Jan 1, 1989

By Toshiro Kuji, Masakazu Fujita, Tetsuji Saito

"The magnetic properties of the magnetic materials were deeply dependent on the microstructures. In this study, the novel technique to produce the desired microstructures in a controlled manner was proposed. The technique consisted of the production of the amorphous alloys and the control of the crystallization process. The technique was applied to improve the magnetic properties of Nd-Fe-B permanent magnets. The microstructural control of the magnets exhibited the excellently high energy-products of higher than 430 kJm-1. The relationship between the magnetic properties and the microstructures of the Nd-Fe-B permanent magnets was discussed.IntroductionThe intrinsic properties of the materials are basically determined by the properties of the constituent elements or the compounds. However, it is often noticed the difference between the observed properties and the theoretical values expected from the intrinsic properties of the materials. This indicates that the observed properties of the materials are determined not only by the properties of the constituent elements. In other words, the observed properties of the materials are also strongly dependent on the morphology of materials. This means that the microstructural control may creates a great improvement of the properties of materials.In Nd-Fe-B permanent magnets, the superiority arises from the uniaxial intermetallic Nd2Fe14B compound which has a large saturation magnetization and a high anisotropy field [1,2]. The magnetic properties of the Nd-Fe-B permanent magnets are dependent on the microstructure, that is, the size, shape and degree of the crystallographic alignment of the Nd2Fe14B phase. Currently, the Nd-Fe-B permanent magnets have been produced by either sintering or melt-spinning [3,4]. In the sintered magnets, alignment of the Nd2Fe14B phase is achieved by the prior green compaction of the crushed ingot powders in an applied magnetic field [3]. In the melt-spinning approach, alignment of the Nd2Fe14B phase is achieved by hot deformation [5]. Amorphous melt-spun ribbons are comminuted and then are consolidated into bulk form by hot pressing before hot deformation. As-hot-pressed magnets have randomly oriented Nd2Fe1~ grains [6]. Subsequent die upsetting of as-hot-pressed magnets gives rise to the crystallographic alignment of the Nd2Fe14B phase."

Jan 1, 1998

Gas flow and heat transfer phenomena in two industrial-scale waste-heat boilers of the Outokumpu copper flash smelting process were analyzed with a commercial computational fluid-dynamics (CFD) package Phoenics. Various operating conditions were simulated for the first boiler and particularly for the second boiler. The gas flow pattern was compared qualitatively with the physical laboratory models, and the general flow pattern was consistent with the laboratory visualization. The heat transfer simulation was validated with, temperature measurements for both boilers, and good agreement was reached between the computed temperature profiles and the measured data. The computational results indicate that gas flow in both boilers is of three-dimensional and recirculating nature. The numerical tracer experiments indicate that some dead volume is present in both boilers, and the boiler modification reduced the dead volume from 38% to 15% under basic operating conditions. Radiative heat transfer accounts for 65-90% of the total 'heat transported in the radiation sections of both boilers under different operating conditions. The modified boiler is very efficient for cooling the off-gases at almost doubled volume flow rate. The CFD modeling proved to be a useful tool for numerical experiments and analysis of boiler performance for process: optimization.

Jan 1, 1998

By Behrouz Abedian, Livia M. Racz

"We address dynamic interactions between high-energy, reactive surfaces of polymer-matrix composites and solid surfaces. A common characteristic of these interfaces is that bonding occurs readily upon contact. In many industrial and biomedical applications, it is desirable to suppress this bonding phenomenon. This interfacial effect is discussed in light of the development of our new method of handling polymer-matrix composites in dental applications. This method involves vibration of the solid-polymer interface at different frequencies. For each material, there is a critical frequency at which the sum of the viscoelastic and inertial energies of the fluid at the surface exceeds the energy available for bonding. When the polymer is vibrated at or beyond this frequency, it does not adhere to solid surfaces. An important aspect of the developed process is that it can be used to characterize surface and interfacial properties of polymers under dynamic conditions, whereas existing techniques are restricted to the study of bulk dynamic properties.IntroductionThe purpose of this paper is to report on the development of a new method for manipulating polymer-matrix composite materials used in dental applications, and the potential of this process for use in materials characterization. The materials under discussion have polymer matrices of a combination of bisphenol A-glycidyl methacrylate (BIS-GMA) and triethylene glycol dimethacrylate (TEGDMA), and contain filler particles of silica and/or zirconia glasses. These materials are called direct aesthetic restorative materials, and are used for filling of cavities, repairing chipped teeth, and for other restorations in which appearance is of importance. They have the appearance of natural tooth material, and are therefore in great demand for use in the anterior portion of the mouth(l,2)."

Jan 1, 1998

Lead blast furnace water-jacket stability was investigated by examining samples from the Port Pirie Lead Smelter. The compositions of the phases formed in the samples were analysed using Scanning Electron Microscopy (SEM) and Electron Probe X-ray Microanalyser (EPMA). Phase equilibria analysis and thermodynamic modelling was undertaken using FactSage with latest thermodynamic database for the slag/matte/metal/speiss/solids multi-component Cu2O–PbO–ZnO– Al2O3–CaO–MgO–FeO–Fe2O3–SiO2–S major and As–Bi–Sb–Sn–Ag–Au minor elements system. Results indicated that the stability of the water-jacket steel wall without freeze-lining is influenced by formation of the complex Fe-rich speiss phase at critical As concentrations. The integrity of the furnace walls with freeze-lining is critically dependent of the stability of the oxide-based freeze-lining which is dependent on various factors including most critical one—the proportion of solids determined by the slag chemistry and fluxing. Thermodynamic modelling of the lead blast furnace operation indicated limiting thermochemical conditions for the water-jacket stability. Factors and controls critical to the water-jackets integrity are discussed.

By Akira Nishikawa

During the twentieth century, the copper smelting industry achieved dramatic expansion corresponding to the vast growth of global economy. This was largely due to innovations in pyro-metallurgical processes, such as autogenous smelting and continuous smelting and converting technologies. However, as copper production capacity increased, its impact on the environment also could not be ignored, and thus with increasing global environmental awareness, many smelting operations either had to renew or rebuild their facilities. In addition to these changes, in places like Japan and Europe, with scarce primary resources, the treatment and recovery of metals from a variety of items such as car shredder dust, used electrical appliances and electronic devices, on top of scraps traditionally treated, is having a profound effect on the reduction of waste and the preservation of primary resources. Thus compared to the days when copper smelting focused on the environmental control in order to break with "Smoke Stack Industry", copper smelting today is making an important contribution to the sustainable development of human society.

Jan 1, 2003

By Akira Nishikawa

During the twentieth century the copper smelting industry achieved dramatic expansion corresponding to the vast growth of global economy. This was largely due to innovations in pyro-metallurgical processes, such as autogenous smelting and continuous smelting and converting technologies. However, as copper production capacity increased, its impact on the environment also could not be ignored, and thus with increasing global environmental awareness, many smelting operations either had to renew or rebuild their facilities. In addition to these changes, in places like Japan and Europe, with scarce primary resources, the treatment and recovery of metals from a variety of items such as car shredder dust, used electrical appliances and electronic devices, on top of scraps traditionally treated, is having a profound effect on the reduction of waste and the preservation of primary resources. Thus compared to the days when copper smelting focused on the environmental control in order to break with "Smoke Stack Industry", copper smelting today is making an important contribution to the sustainable development of human society.

Jan 1, 2003

By Michael Sheedy

Recoflo® ion exchange technology utilizes fine mesh resin beads, a fully packed resin bed, and counter-current regeneration. These unique features help to improve exchange kinetics, reduce regenerant consumption, and increase the concentration of strip solutions. Commercially, Recoflo technology has been extensively used in the following areas: the separation of strong mineral acids from dissolved metal salts, the purification, removal and recycle of dissolved metals in the surface finishing industries, and the production of high purity water. In the mining and metallurgical industries Recoflo ion exchange systems have been installed to treat a copper refinery bleed stream at Falconbridge's Kidd Creek plant and to treat a nickel and cobalt bearing ammonium sulfate effluent stream at another primary metal producer's facility. In the first application an APU® Recoflo system is used to separate the sulfuric acid at 200g/L from the dissolved copper and nickel sulfate salts at 80 g/L. The absorbed sulfuric acid is recovered from the resin by elution with water and is then returned to the refinery electrolyte circuit. In the second application a chelating ion exchange resin is used to remove nickel and cobalt at 0.01 - 3.0 g/L from process streams containing 120 - 240 g/L ammonium sulfate. This Recoflo system has been designed to reduce the nickel and cobalt levels to 0.001 - 0.002 g/L while recovering cobalt and nickel at concentrations up to 30 g/L and 15 g/L respectively. Case studies for both these metallurgical applications and other Recoflo processes are presented in this paper.

Jan 1, 1998

By B. Abedian, L. M. Racz, S. R. Berry, R. W. Hyers

"The presented work represents an effort to improve understanding and prediction of turbulent flow inside electromagnetically-levitated droplets. We show that the flow field in a test case, a nickel droplet levitated under microgravity conditions, is a low Reynolds number turbulent flow, i.e. in the transitional regime between laminar and turbulent. Past research efforts have used laminar, enhanced viscosity, and k - E turbulence models to describe these flows. In our study, we compare the RNG algorithm to laminar and k - E turbulence model results. We show that accurate description of the turbulent eddy viscosity µr is critical in order to obtain realistic velocity fields, and that µr cannot be uniform in levitated droplets. In the RNG method there are no characteristic length or time scales associated with the flow, thus allowing such anisotropic features to be captured. We perform calculations and analyses for two cases (1) a small, non-deforming, spherical nickel droplet and (2) a deforming, oscillating droplet. In addition to flow field calculations, we compare numerically-obtained surface tension and viscosity values to those obtained experimentally by the oscillating drop technique.IntroductionElectromagnetic levitation (EML) is a containerless processing technique for conductive materials. Its advantages are the avoidance of contamination or chemical reaction at container walls and the ability to perform long-term experiments in a metastable state. Because of its current limitation to small sample sizes, its primary use is in the laboratory. One application of interest is the measurement of thermophysical properties of undercooled liquid metals [1, 2, 3, 4]. In EML, a sample weighing approximately 1 gram is positioned inside an electromagnetic field generated by alternating currents flowing through an axisymmetric water-cooled copper coil. The coil must be designed appropriately so that thesample levitates in a stable manner.Traditionally, mathematical modeling has been performed in tandem with both earth-and spacebound electromagnetic levitation experiments, in order to determine the effect of the magnetic field on material and flow characteristics [5, 6, 7, 8]. These calculations are important because they allow design, planning, and correct interpretation of experiments. In addition, the calculations are of fundamental scientific interest, as they can be applied to other electromagnetic materials processing applications [9]."

Jan 1, 1999

By K. A. Brunk

Newmont's research, operations, history and experience with pre-treatment of preg-robbing carbonaceous ores are described, with emphasis on the chemistry, physics and kinetics of chlorine treatment. Present operations, control strategy and projected changes are also described, including a summary of the adsorption of chlorine into pulps and off-gas scrubbing. Conditions of chlorination have been optimized by the use of Eh-pH diagrams of the gold-chlorine-water system, and have resulted in significant increases in gold recoveries and decreases in chlorine consumptions.

Jan 1, 1987

By J. Fraser Forbes

"The meaning of the term ""process control"" has evolved significantly since its widespread use began in the manufacturing industries in the 1940s. Further, the scope of process control applications has drastically increased both in terms of the breadth of industries using process automation technologies and the vertical integration of these technologies within a single industry. This evolution and integration of process control technologies within the manufacturing industries has proceeded to such an extent that process automation is an integral part of modern business practices.This paper will examine the current status of process control technology from simple process regulation through process performance optimization to business planning. Each layer of the operations automation hierarchy will be discussed both in. terms of the current state-of-the-art and the directions in which these technologies are evolving. The key tools and tasks necessary for success at every level of the automation hierarchy will be introduced. Finally, the critical challenges that must be faced in accomplishing the goal of complete Computer Integrated Manufacturing (CIM) will be described.Finally, although this paper addresses issues of practical importance to any manufacturing company, the discussions will be framed in terms of the particular challenges facing and the opportunities available within the materials manufacturing industries."

Jan 1, 2000

By A. Perillo

The process, realized in. the Kivcet furnace, can convert continuously lead concentrates, residues and secondary lead bearing materials into a lead bullion free of sulphur and a discardable slag. The lead recovery can be up to 99%. The long experience of about three years at Portovesme demonstrates the capability of the furnace to smelt a very. high range of lead raws without interruption of the operation. The operating costs are very competitive in comparison to the traditional technology. The work place and environment are clean and new tight regulations for the? hygiene control are met. The Kivcet furnace can be considered as consisting of three parts (reaction shaft, waste gas shaft and electro-furnace) connected with a common hearth. The technical basis of the furnace construction is the application of a number of design elements .which have mostly been used before in designs of industrial furnaces, such as open hearth furnace, refining furnace and other furnaces dealing with liquid meta1s. Refractory wear in the reaction shaft with typical pattern from watercooling soon has been stabilized and since maintained. No deformation of the furnace shell and no leakage of metal or s:l:ag through the bottom is? appeared after three years' operations.

Jan 1, 1990

By Xia Zhao, Yong Zhao, Wen Pan, Ze-jun Ma, Yan-juan Yang

Characteristics of the gas-solid reduction reaction between iron ore sinter and carbon monoxide (CO) gas at 1273 K were studied with thermogravimetric analyzer. The microstructure, mineral compositions and porosity of sample were investigated prior to reduction, in the 30% reduced sample, in the 70% reduced sample, and in the fully reduced sample. At the reduction degree of 30%, the hematite and calcium ferrite was reduced to 44.4 and 60.4% respectively. At the reduction degree of 70%, all the hematite, calcium ferrite and magnetite were reduced to metal iron, only 36% wustite was left in the core area. The reduction reaction began with the loose structures and spread to the nearby area. In the area of micropores, the reducing gas can easily diffuse to the reaction interface to proceed the reduction reaction effectively. So increasing the content of micro-pores is an effective way to improve the reducibility of the sinter.

Mar 1, 2018

By Fuming Wang, Xi Chen, Shuai Liu, Changrong Li, Dan Wu, Yaxu Zheng

The effects of B content and austenitizing temperature on hardenability and toughness of Cr–Mo alloy steel have been studied. The results show that the hardenability is deteriorated with increasing B content and austenitizing temperature. With increasing temperature, more and more B containing particles were dissolved in austenite and increase the amount of B atoms segregating at grain boundaries. Moreover, the coarsening grains reduce area of grain boundaries and also increase the amount of B atoms at unit grain boundary, excessive B atoms segregating at grain boundaries promotes precipitation of M2B, which accelerates ferrite nucleation and reduces hardenability. The main elements in M2B phase are Fe, Cr, Mo and B. The B atoms segregating at grain boundaries during austenitizing promote precipitation of M2B during tempering which deteriorate toughness significantly.

Mar 1, 2018

By Hani Henein, J. Barry Wiskel

"The easy accessibility and power of the PC, as well as the education of our engineering students in the use of these tools, are compelling reasons for developing computer aided instructional (CAI) tools. There are a wide range of areas in the engineering curriculum where students must learn the steps and the process of applying judgement in problem solving. In the typical course instruction, · an instructor introduces theory to students; the application of the theory to solving problems is often demonstrated in the abstract. Students therefore spend a significant amount of time learning how to apply the theory to problem solving. Additional time and effort must then be spent to get students to the point of learning concepts and integrating this knowledge. A number of computer aided packages have therefore been developed for use in several courses in the materials science and engineering curriculum that encompass both calculational and instructional capabilities. This paper presents an overview of some of these packages which include the solution of a non-linear equation, the instruction of binary diffusion couples, an introduction of crystallography, an introduction to heat transfer and the solution of thermodynamic stability diagrams. The context in which these CAI Tutorials were developed and are being used will be discussed. The pitfalls in the development of these packages will also be discussed. The use of the tutorials has important implications on the expectations from an engineering education of both instructor and student.IntroductionTraditionally, it is quite routine to teach engineering students how to use a computer (the PC today for undergraduates) as a tool in performing engineering calculations or in simulating a process or a unit operation. This often takes the form of one course in computer programming, whether it is Fortran, Visual basic or a spreadsheet, and another course in numerical computation. However, the materials and electronic revolution have brought about considerable advances in computer power and speed, and accessibility. Today, the manipulation of digital images, movies, and speech are commonplace on a desktop PC.' Many mathematical models that were executed only on workstations can now be readily handled on a PC. Concurrently, more of our students own a PC even if their curriculum does not require them to purchase one. Today, virtually every university student has been introduced to the PC in either their elementary or high school education. Hence, the increased capabilities and accessibility of the PC and the familiarity of students with this tool make it compelling to explore its use as an educational tool for our engineering students. This is not a traditional role of a computer in our engineering curriculum."

Jan 1, 2000

By U. M. Mutnti

In order to meet the stringent market requirements for high purity cobalt, ZCCM commissioned the VIR plant in December 1982. The plant comprises a 4.1 tonne/heat vacuum induction furnace with a rated annual capacity of 2,500 MT of barstock. In the VIR furnace, molten cobalt is held under vacuum at 1600°C resulting in the removal of more volatile impurity elements by distillation. Operations todate have demonstrated that Pb, Zn and Cd have good distillation rates in excess of 95%, leading to cobalt containing 1 ppm or less of the above elements. Removal of other impurities such as Se, Bi is about 65% with the finished product still assaying around 1 ppm of each of these elements. Vacuum refining of cobalt offers an economic route for producing higher grades of cobalt from the type of concentrates and treatment processes available within ZCCM. The consistency of VIR cobalt quality has been confirmed by ZCCM and some of its alloy customers.

Jan 1, 1988