Search Documents

By Li. Jiarong, Zuojian Liang, Qingyan Xu, Baicheng Liu, Shizhong Liu, Hailong Yuan

Single crystal solidification of turbine blades is a key technology for the production of reliable and high efficiency gas turbines. The solidification process of single crystal investment castings causes a number of problems that have to be solved such as the increase of casting defects and complexity of production process. Computer modeling and simulation is helpful to predict the defects and improve the process design. In the paper, a mathematical model for three dimensional simulation of solidification and single crystal growth of investment castings was developed based on CA, mechanism of crystal growth and basic transfer equations such as heat, mass transfer equations. Many factors including constitutional undercooling, curvature undercooling and anisotropy, which had vital influences on microstructure evolution, were considered in the model. Temperature, crystal growth interface and structure defects of investment castings of single crystal superalloy were investigated at withdrawal rates of 4.5mm/min and 7mm/min. Simulated results showed that microstructure evolution and structure defects were predicted reasonably and calculated results were coincident with experimental ones. The study indicated that three dimensional solidification simulation technique is a powerful tool for understanding the fundamental of solidification and the formation of structure defects in single crystal investment castings and finally for optimizing process design.

Jan 1, 2004

By P. Hajiani

Rare earth elements (REEs) are critical materials in many leading-edge technology products. However, REE separation outside China has remained a challenge in addressing environmental concerns of current production. The author has worked on a technique employing the emphasised variability in the electrophoretic mobility (μi) of REE for the purpose of REE separation. In continuation of the results presented in IMPC 2016 [1], this contribution summarizes the progress achieved in 2016 and 2017. The major goal was to increase the REEs concentration by a factor of 1000 and to attenuate the consequent drawbacks, specifically joule heating effect. Amphiprotic hydroxylic solvent was selected to replace water, which has a major impact on the complexation mechanism and buffer requirement. Non-aqueous media result in a significant drop in the specific molar conductivity of the electrolyte, whilst μi reduces several times only. Moreover, a quasi-steady state electrophoretic separation in conjunction with temperature gradient focusing is adapted to improve scalability.

By B. R. Davis, Neale R. Neelameggham, R. E. Brown

The element Calcium element has a unique place in the production of etals, intermetallics and other compounds. The unusualness arises from the fact that we have several possible reductants – metallic calcium, calcium carbide, calcium cyanamide and calcium hydride. A review of how metallic calcium is manufactured and utilized is presented. The difficulties involved in producing the metal in large quantities and price implications are noted. . Fundamental thermodynamics of how these act as reductants are shown, along with the historic application of these in metal production during the past century and a half. Alternate applications as to how to control the cost of the reductant is indicated, such as the numerous attempts in making low cost titanium utilizing direct or indirect calcium reductant.

Jan 1, 2014

By W. K. Connor, O&apos

The U.S. Bureau of Mines, in cooperation with the Idaho National Engineering Laboratory (INEL), conducted over 30 hours of melting tests to vitrify simulated low-level radioactive wastes from the INEL Radioactive Waste Management Complex (RWMC). Five separate waste compositions were investigated, each consisting of noncontarninated soil from the RWMC and surrogate materials used to simulate the actual buried wastes. The RWMC soil and five waste compositions were melted in a 50-lb, single-phase electric arc furnace with a water-cooled shell. These tests were conducted to determine melting parameters in preparation for a large-scale melting campaign to be conducted in the Bureau's 1-metric ton (mt), water-cooled-wall, 3-phase electric arc fumace. Bulk chemical composition was determined for each of the feed materials and for the slag, metal, fume solids, and offgas furnace products, and distributions were calculated for the key elements. The material balance for the furnace operation indicates that from 63 to 84 pct of the feed reported to the slag. Cerium, used as the surrogate for the radionuclides in the wastes, demonstrated an extremely strong affinity for the slag product. Although slag temperatures as low as 1250° C were recorded when melting the RWMC soil, temperatures in excess of 1600° C were necessary to achieve the fluidity required for a successful slag tap.

Jan 1, 1994

By Junbiao Liu

Rutile is mostly produced from placer sands. Its beneficiation from primary deposits has rarely been investigated. However, there is interest in primary deposit because of the depletion of sand deposits. The Zaoyang deposit in China is the only rutile primary deposit currently mined. The plant employs a Tabling-Magnetic process which recovers only 20% Ti02 at a grade of 87%. This study shows that significant improvement on the recovery (52% at the same grade) can be achieved. This study includes a detailed mineralogical examination and the development of a processing flowsheet of the ore. The gangues are primarily amphiboles, garnets, zoisites, and chlorites. The liberation of rutile occurs at about 200 mesh. Gravitational, flotation, and magnetic separations are all employed in the process developed, depending on the mineral characteristics and experimental results. The flotations circuit utilizes benzyl arsonic acid to float rutile and sodium fluosilicate to depress the gangues. This is a new reagent scheme for rutile flotation.

Jan 1, 1989

By Richard L. Summers

The shaped charge has proven in various military and industrial applications to be an effective penetrator of materials. Upon initiation a detonation wave traverses the explosive billet, collapsing a metallic liner and creating a jetting process. From multiple non-simultaneous flash radiographs of the jet in free flight, the observer can study the collapse, formation, and growth of a shaped charge jet. Digitization of a particulated jet's position and shape from the radiograph into electronic storage files provides the experimentalist with an efficient basis for data reduction. With the aid of a simple personal computer, one can in a matter of minutes generate a wealth of information concerning jet formation after initiation and thus gain insight into the quality of its manufacture, design, and assembly. This paper will in detail explain the methods in place for fully automated data reduction of radiographic films. Methods of computer aided digitization of particulated jets and analysis of physical jet characteristics and performance will be discussed.

Jan 1, 1992

By Jagdish C. Agarwal

Although copper ranks very low in the order of abundance of elements in the crust of the earth, it has been one of the first metals utilized by mar, at his emergence from the Stone Age, about 10,000 years ago. Use of copper for weapons, tools, utensils and ornaments dates back to the twilight of history, 6,000-5,000 B.C. Native copper outcrops and the malleability of the metal explain its very early use by the cave-dwellers. The working, melting and extraction of copper from its minerals are among the oldest metallurgical achievements of the human race. The oldest complete smelting installations for the extraction of copper from its minerals, dated about the fourth millenium B.C., were recently discovered in the Timna Valley, Wadi Arabah, Israel. (1) The history of the developments of the extractive metallurgy of copper has been adequately reviewed recently. (2,3) The center of copper production migrated from the Eastern Mediterranean to Northern Europe (Mansfeld, Germany, Swansea, Wales) towards the end of the Middle Ages (1500 A.D.). The production of the metal was boosted tremendously in North America since the end of the nineteenth century (Fig. 1).

Jan 1, 1976

By W. C. Chang

Phases and magnetic evolutions of melt spun Nd9.5(Fe1-xCox)85.5B5 (x=0, 0.05, 0.1 and 0.15), (Nd1-yLay)9.5Fe85.5B5 (y=0, 0.0.5, 0.1; and 0.15) and (Nd0.95La0.05)9.5(Fe1-zCrz)81.5B9 (z=0, 0.033, 0.067 and 0.1) nanocomposites: have been investigated. It was found that a. dilute Co substitution for Fe, x=0:05-0:15, in Nd9.5(Fe1-xCox) 85.5B5 improved not only Curie temperature but also the remanence and maximum energy product. Partial substitution of La for Nd in(Nd1-yLay)9.5Fe85.5B5 may suppress the grain growth of the materials during thermal treatment. Exchange coupling between the Nd2Fe14B and a-Fe was found: to increase with increasing La content. A dilute La-substitution, y=O. 10, has proven to decrease the optimum wheel speed required for preparing melt spun ribbons with better magnetic properties; Furthermore; a slight substitution of La for Nd in (Nd0.95La0.05)9.5(Fe1-xCrx)81.5B9 nanocomposite reduced the crystallization temperature of the over-quenched ribbons and led to the formation of a multiple phases mixture. Nevertheless, a dilute Cr addition increases the Tg of (Nd0.95La0.05)9.5(Fe1zCrz)81.5B9 and also suppresses the formation of the undesired (Nd,La)2Fe23B3 and Fe3B phases: Cr was found to play an important role in grain smoothening or magnetic separation which consequently increased the Hc of Cr-containing materials.

Jan 1, 1997

By Juha Järvi

Outokumpu Zinc Oy has two separate roasting lines with fluidized bed furnaces and waste heat boilers for calcine collection and heat recovery. During the last 30 years, zinc production in Kokkola plant has increased continuously and at the same time the raw materials have changed. Therefore, the waste heat boiler has been under continuous research and development. The waste heat boiler plays a significant role in the process and consequently the reliability and efficiency of the device is important for the effectiveness of the entire process. Many changes have been made to the boiler in the last decades. New radiation tube screens, tube bundles, and baffle-plate constructions have been added to the boiler and also rapping systems for the dust have been developed. The latest improvement to the boilers was a baffle wall, located in the middle of the radiation section roof in the first boiler, and baffle plates in the lower part of the convection section in the second boiler. The new boiler design and optimization were carried out using physical water and air-dust modeling as well as computational fluid dynamics. The modeling work agrees well with experiences in practice. The latest developments have increased the operating hours per year and the effectiveness of the waste heat boiler.

Jan 1, 2002

By Yuanbo Zhang, Zhixiong You, FENG ZHOU, Guanghui Li, Zhengwei Yu, Zhiwei Peng

Reduction disintegration of sinter significantly affects the coke consumption and productivity of blast furnace smelting. As we know, the reduction disintegration index (RDI+3.15) of sinter obtained from titanomagnetite concentrate is relatively worse than those from ordinary iron ores. In this study, the effect of sintering parameters, mainly involving coke breeze dosage and basicity on sintering indexes was investigated using titanomagnetite concentrate as raw material in an experimental-scale pot. Subsequently, RDI+3.15 of the sinter was detected according to the Chinese standard of GB/T13242-91. The results show that RDI+3.15 rises with the increase of coke breeze dosage, while it decreases with increasing basicity from 0.5 to 2.0 and then increases in the basicity range of 2.0-3.0. Finally, the microstructure of sinter before and after reduction was studied. And the mechanism of reduction disintegration was preliminary revealed by analyzing the morphologies and distributions of minerals in the sinter.

Jan 1, 2015

By Esperidiana A. B. Moura, Célio H. Wataya, Roberta A. Lima, Rene R. Oliveira

Biodegradable starch/copolyesters/silica nanocomposite films were prepared by melt extrusion, using a twin screw extruder machine and blown extrusion process. The influence of the silica nanoparticle addition on mechanical and thermal properties of nanocomposite films was investigated by tensile tests; X-rays diffraction (XRD), differential scanning calorimetry (DSC) and Scanning electron microscopy (SEM) analysis and the correlation between properties was discussed. The results showed that incorporation of 2 % (wt %) of SiO2 nanoparticle in the blend matrix of PBAT/Starch, resulted in a gain of mechanical properties of blend.

Jan 1, 2015

By Takashi Miyamoto, Hideo Nakae, Hideki Yamaura, Takeshi Yanagihara

"For the production of partially composed metal matrix composites, namely discontinuous MMCs, using a casting· process, the interpenetrated phase composites with SiC particles were fabricated by pressureless iDfiltration using molten Al-Si alloys. This process is based on a wetting phenomenon, therefore, we discussed the technique based on the reactive wetting. The SiC particles coated by diluted water glass were sintered in a mullite Tammann tube and simultaneously infiltrated with molten Al-Si alloys in air at 1173~1573K. As for the improvement of the wettability between the SiC and the liquid aluminum alloy, Fe3O 4 powder was mixed with the water glass due to the thermit reaction between Fe3O4 and molten aluminum alloy. In some experiments, pure aluminum powder was placed on the sintered SiC to increase the interfacial area and the chemical reaction between the sintered Sic. and the melt. By combining these conditions, we succeeded in the complete infiltration without pressure at 1173K.IntroductionAs is well known, the mechanical properties of metal matrix composites (abbreviated MMCs) are superior than that of ordinary metals. However, their use has not been widely accepted because the production cost is very high due to their poor machinability. Therefore, the production of partially composed, namely discontinuous MMCs, by as the Lanxide process [l,2] has been investigated for many years. The Lanxide process, it takes a long time, sometimes up to 10h, in a nitrogen atmosphere for the infiltration. Therefore, the cost will be higher for common use. On the other hand, a high 'pressure process has been adopted for the production of discontinuous MMCs by the Toyota Motor Corp.[3]."

Jan 1, 2000

By Hao Deng, Hongmin Zhu, Jichao Li, Kai Huang

"Silicon and silicon carbide mixing micropowders obtained from the saw cutting industry of polycrystalline silicon ingot is separated by a simple sequential sedimentation. The Zeta potentials of the powders in the aqueous suspension are adjusted by varying the pHs with dilute acid or alkaline reagents. The dispersion and aggregation content of the microparticles is significantly influenced by pHs, and so their settlement velocity in the same hydraulic conditions are quite different, and silicon powders tend to suspend in the upper section of the suspension for its finer size and smaller density under the stronger Zeta potential repulsion force. The original content of the cutting powders with 30%wt silicon are separated into the Si-rich and SiC-rich powder respectively, and 62%wt Si-rich powder can be obtained after 4 times of sedimentation under pH = 8.0, showing the great potential for Si and SiC powder separation and recovery in a cost-effective way.IntroductionWith the fast development of photovoltaic (PV) technology these years, the market demand for the solar-grade high pure silicon material significantly increased, making the silicon recycling and recovery from the wire sawing slurry profitable and attractive[1]. Waste silicon slurry was produced in the multi-wire sawing process of a silicon ingot by using an ethylene glycol-based solution and silicon carbide abrasives as the slicing system. During this slicing process, about 30% of the silicon ingot will become the waste as the fine particles suspended in the slurry, which mainly consists of silicon kerf-loss particles, SiC fragmental particles, tiny iron fragments from the worn sawing wire and ethylene glycol-based solution [2]. The separation of above individual component is usually easy except for Si and SiC fine particles for their quite similar properties. So the biggest challenge for the effective recovery and recycling of silicon particles from the wire sawing slurry actually lies in the mutual separation of silicon and silicon carbide particles."

Jan 1, 2012

By Peter Willbrandt

The flash smelter at NA was commissioned in March 1972 with an initial throughput of 50 tons of dry copper concentrate per hour. As a result of various measures, for example, oxygen enriched process wind, extension of the radiation part of the waste heat boiler, etc., the throughput could be increased to the present 70 tons per hour of dry concentrate. NA's plant is located on the outskirts of the city of Hamburg. The flash smelter's location and the growing awareness of the German population as regards environmental issues necessitate again and again considerable capital expenditure being spent on environmental protection. Thanks to the numerous small and large measures taken to protect the environment the emissions of dust, heavy metals such as arsenic, copper, lead, etc., and as well SO, could be drastically reduced. This paper will be giving an overview on the present state of the flash smelting process and the impact of the increasing environmental awareness at NA.

Jan 1, 1993

By Edwin de Jesús Deveaux

After 32 years of operations beneficiating lateritic nickel ore in a fully integrated pyrometallurgical complex, Falconbridge Dominicana (FALCONDO), situated at Bonao and La Vega Provinces, Dominican Republic, has become profitable with one of the lowest nickel grade content processing plants in the world, and literally without any by-product (granulated slag, will be utilized in the future as a post-processing subproduct). To December 2002, mineral reserves were 64.1 million tonnes containing laterite grading as low as 1.15 % Ni when full dilution is applied. At a cut-off grade of 1.20% Ni, the reserves will provide 15-20 years of production. The mineralized thickness over the seven active deposits averages 6 m. Development of very selective and unique mining practices, together with improvements in the process plant, are key to achieving the production goal (30 kt Ni/yr) and to meet the quality standards for the ferronickel produced. Keywords: Laterites, grade control, mining methods, environment

Jan 1, 2004

By Robert A. Medower

This paper will review the operational benefits of applying contemporary control technology to balance the blast to a cupola. Reported benefits from existing installations include reduced channelling, higher pour temperature, reduced oxygen consumption, lower coke consumption & reduced emissions.

Jan 1, 2001

By Qionghua Zhou, Wei Liu

"Nanocrystalline silver bulk material with average grain size of 20.3 nm was prepared by warmvacuum- compaction method. The as-prepared nanocrystalline silver was characterized by X-ray diffraction (XRD), differential scanning calarmeutry analysis (DSC), thermogravimetric analysis (TG), and 6157 type Electrometer test, respectivily. The experimental results show that the average grain size and microstrain of the nanocrystalline silver are 20.3 nm and 0.088%. The melting point and melting enthalpy are 1228.7 Kand 82.34 Jig, which are lower than that of coarse-grained silver by 6 Kand 22.6 Jig, respectively. The electrical resistivity of nanocrystlline silver increases with higher temperature when the range of temperature is between 233K and 293K. The electrical resistivity at 293 K is 1.475xlO -7 Q·m, which is higher than that of coarsegrained silver by a factor of 9.IntroductionN anocrystaline ( nc) materials or nano structured ( ns) materials are three-dimensional (3 D) bulk materials with average grain size typically smaller than 100 nm. Ne materials have been of great interest for their unique properties, such as superior tensile strength [1-2], high microhardness [3- 4], superplasticity [5-6], magnetically quasi-isotropic [7-8] , and so on, making them one of the most promising nano-scale materials with wide applications. Ne materials with average grain size of 5-10 nm were firstly fabricated by Gleiter et al. [9] in 1980s, using inert gas condensation (IGC) method. Unfortunately, the large surface to volume ratio creates a high surface energy component in the total free energy of the system and results in a metastable state in the materials. Therefore, due to the signfica nt disordered grain boundary regions, nanomaterials are thermally unstable and are subjected to a strong driving force for grain growth. The grain growth even occurred at room temperature [10].The conflict or deviation of measured date, e.g. strength, microhardness, thermal stability, partly due to the grain boundary ratio or the distribution of grain size, and partly derived from imperfections such as voids and microcracks while earlier processing techniques are known to result in incomplete dens:fication [11-12]. Therefore, the higher quality samples produced in subsequently years still show such a general trend."

Jan 1, 2011

By Olli Hyvärinen

The capacity of Outokumpu Pori Copper Refinery has been increased by 50 % to 70 000 t/a in the last five years by adopting periodic current reversal, reducing spacing and installing some new cells in the old tank house building. Five years operation of PCR has proved that it is possible to achieve additional capacity with PCR and yet produce high quality cathodes. The impurity level in anodes has considerably increased, and recently, arsenic, antimony and sometimes bismuth have displaced nickel as the most critical impurity.

Jan 1, 1987

By G. M. Bond

Reduction of the emissions of greenhouse gases, such as CO,, is currently the subject of extensive research. A novel strategy is put forward here, based on a biomimetic approach providing accelerated deposition into carbonate form for long-term sequestration. It offers the advantages of a process that: does not require concentration of CO, from flue gases; could potentially be used in an on-site scrubber to provide a plant-by-plant solution to reducing CO, emissions; is an environmentally benign procss with an environmentally benign product; and is based on readily available, low-cost reagents (except perhaps the catalyst).

Jan 1, 1999

By D. H. H. Quon

Results of a study conducted to determine the properties of iron ore pellets made from Mount Wright and Carol Lake ore concentrate fines with partial and full substitution of bentonite by several organic binders are presented. Carboxy methyl celluloses 7H and 6TL, hydroxy ethyl cellulose (natrosol) and modified guar gum all produce pellets of acceptable wet, green and dry strength. However, when fully substituted, an inorganic binder such as calcium carbonate is required for satisfactory strength development after induration. Mixing the Carol Lake ore with Mount Wright ore in a 50-50 ratio also achieves the same result. The failure of the Carol Lake ore in the pelletization process is attributed to the low hematite content of the ore. The results are very similar to those from the extrusion studies reported earlier (8).

Jan 1, 1989