Search Documents

By lndu S. Das

An analytical simulation of the material characteristics of Inconel 718 is developed and bounds for mechanical and microstructural stability are obtained for isothermal and temperature-dependent cases. Experimental flow stress data using hot compression tests are reported for a wide range of temperature and strain at various strain rates. A parametric study of strain rate sensitivity, dissipation and entropy are presented. A complete set of processing maps delineating the stable and unstable regions are developed to help define the most efficient means of manufacturing an Inconel product.

Jan 1, 1992

By Mikio Kobayashi

Extraction of valuable metals from sulfide ores continues to be a very important, process and so the strict control of discharge of harmful metals in effluents from refineries becomes more important in the future. The recovery methods for heavy metals have been developed. Some metals such as Se and As are still difficult to be removed to very low concentration, although the techniques for recovery and removal for many kinds of heavy metals have already been developed. Especially, in case of Se the recovery system from water with low concentration has not be developed yet, although the WHO decided Se to be harmful for human beings and then the discharge control is under obligation now. In general Se exists as selenite ion and/or selenate ion in aqueous phase and selenite ion is able to be recovered by coprecipitation with ferric hydroxide or by reduction to solid selenium by general reductants. Selenate ion, however, has a strong resistance to conventional treatments. Therefore the new technique for the recovery of Se from water including selenate ion has to be developed. In this presentation the new approach for removal of selenate ion using the reaction in which ferrous ion is oxidized to ferric ion is presented. Selenate ion is reduced to selenite ion during the reaction and then to solid selenium, while ferrous ion is oxidized to ferric ion. The coexistence of activated carbon is very useful to increase the reaction rate. The use of iron powder is also effective and very useful for reducing gel-like precipitates mainly consisted of ferric hydroxide. The concentration of the residual selenate ion is probably under 0.1 ppm after recovering Se by the mentioned-above approach. In addition to the mechanisms of these reactions, the effects of pH, coexistent positive and negative ions, and reaction temperature are also presented. Furthermore the investigation of the behavior of selenosulfate is presented.

Jan 1, 1998

By J. L. Delplancke

During copper electrowinning in sulphate electrolyte, intense oxygen evolution takes place at the anode. Lead alloy anodes are progressively replaced by dimensionally stable anodes in order to avoid the cathode contamination by dissolved lead. The electroactive coating of these anodes has to be as cheap as possible, adherent to the substrate, electrochemically stable and has to be efficient at high current density and high temperature. This requirement is even demanding in case of copper electrodeposition for the production of thin copper foils for the electronic industry. The production of thin (20 µm thick) copper foils for the printed circuit boards requires high purity copper electrodeposited at a current density as high as 7,000 A/m2. The choice of a long term coating composition is driven by economics. The purpose of this paper is mainly to review the anode compositions suitable for copper electrowinning and for copper electrodeposition at high current density. A short description of preliminary results obtained with a new anode coating on a titanium substrate is also presented.

Jan 1, 1999

By Mark Samonds

"Manufacturing processes which involve liquid to solid and solid state transformations in metals encompass a wide variety of physical phenomena. The past twenty years have seen a steady evolution in the complexity and scope of numerical models of these processes, beginning with thermal analyses without phase change. Recently, a few software packages have become available which have true multi-physics capabilities. This permits the treatment of thermal, fluids, stress, electromagnetic, chemical reaction and microstructure development aspects altogether in a fully coupled simulation. This paper will consider various aspects of these types of models.Coupled thermal and fluid flow analyses of continuous castings have been around for fifteen years. Coupled thermal and free surface fluid flow simulations of shape castings have been available for ten years, including view factor radiation models for investment castings. Only recently, however, have fully coupled thermal, fluid, and stress analyses become practical. This implies the reverse coupling of the mechanical deformations to the solution of the energy and momentum equations through modification to the interface heat transfer coefficients and the fluid domain geometry. This has been implemented with a combined eulerian-lagrangian finite element method. Appropriate mechanical constitutive models will also be discussed.Many types of defects need to be predicted in casting processes. Those related to stress include hot tearing, hot cracking, part distortion, and thermal fatigue in dies. Macroporosity, microporosity, and microsegregation are determined by the solidification behavior and microstructure development in a casting. In particular, microporosity is influenced by dissolved gases, the morphology of the mushy zone, the liquid to solid density change, and the local pressure conditions. Macrosegregation is caused by the partitioning of solutes during. solidification and subsequent thermo-solutal convection. An additional transport equation is required for each solute that is being tracked. Computational thermodynamics is being incorporated into these types of analyses to determine transformation temperatures, partition coefficients, densities, and enthalpies. In combination, the microstructure and microporosity models can frequently predict a variety of mechanical models, such as yield strength, tensile strength, and elongation."

Jan 1, 2001

By Elliot Schwartz, Julian Szekely

"In this paper we describe an experiment that was recently performed on the IML-2 Space Shuttle mission in which the thermophysical properties of molten metals were measured using electromagnetic levitation. In the planning of these experiments calculations had to be performed to predict the levitation and stirring forces, heating rates, sample deformation, and internal flows within the sample. These predictive calculations were essential for both the planning of the experiments and for the re-planning of experimental runs during the actual Space Shuttle mission.Introduction""Materials Processing in the Computer Age"" involves the use of mathematical modeling to obtain a quantitative understanding of the phenomena that govern materials processing operations. Microgravity, or space shuttle experimentation represents a specific case in point here; the very high cost of the space shuttle flights, the very limited flight opportunities that are available, and the tight resources aboard a shuttle clearly mandate that these experiments be very precisely planned and that all possible opportunities for mathematical modeling be fully exploited.The purpose of this paper is to present the results of calculations performed for the planning of a space shuttle experiment involving electromagnetic levitation and wherever possible present a comparison of the computational predictions with both experimental measurements and asymptotic analyses. Finally we shall seek to discuss the practical implications of both the computational methodologies and the potential experimental findings."

Jan 1, 1994

Lime-enhanced carbothermic reduction may provide an alternative process for treating low grade chalcopyrite concentrates. To date, most research on lime-enhanced reduction has been on pure, synthetic sulfides. In this study, preliminary experiments were carried out on natural chalcopyrite using a thermal analysis system to assess the rate and extent of reaction at several temperatures and identify the major solid and gaseous reaction products. Calculations were performed to establish the thermodynamic limits of the reactions in the temperature range of interest in order to identify the potential conditions for processing chalcopyrite concentrate. The study found that finely ground chalcopyrite can be reduced carbothermically in the presence of lime at moderate temperatures and in a reasonable time to form metallic copper, with the sulphur reporting virtually entirely to calcium sulfide. At temperatures below about 750?770ºC calcium ferrite is the stable form of iron whereas at higher temperatures metallic iron is stable. Further work is required to demonstrate the reaction on a scale to obtain sufficient sample for evaluation of subsequent processing steps to remove the gangue material and iron products from the copper.

Jan 1, 2009

By Ben Q. Li

An efficient numerical algorithm for solving steady state heat transfer and solidification problems is described. The algorithm is of boundary integral type and is based on the formulation of the field variables along the boundary of the domain of interest. Compared with the familiar domain-based methods, such as the finite element and finite difference (or finite volume) methods, this boundary-based method has an advantage of solving fewer unknowns and hence has a potential for reducing computational time significantly. Another and yet more important advantage of the present algorithm is that it is a stable scheme and is not prone to numerical oscillations resulting from convective effects, as often encountered in the domain-based methods. Therefore, no numerical or artificial diffusion (such as streamline upwinding) is necessary. Numerical examples are presented that are drawn from processing systems for producing aluminum-based materials.

Jan 1, 1994

By Anne C. Chinellato, Alejandra T. Soria, Nelida L. del Mastro, Amanda C. S. Pereiral, Esperidiana A. B. Moura, Anibal V. Abreu

"This work presents a comparative study of the thermo-mechanical and morphological properties of sugarcane bagasse fiber/HDPE composite treated with electron-beam and gamma radiation. The composite samples obtained by extrusion and injection molding processes were irradiated at 50 and 90 kGy using either a 1.5 MeV electron beam accelerator or gamma irradiator EMI-9, at room temperature in presence of air. The irradiated and non-irradiated samples were submitted to mechanical and MPI tests, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), sol-gel analysis and X-Rays Diffraction (XRD) and the correlation between their properties was discussed. Improvement of the bagasse fiber/HDPE composite properties, using electron-beam or gamma radiation, was found.IntroductionResidues of sugarcane bagasse fiber are widely produced in Latin America and other countries: in Southern Africa, Egypt, South-Eastern Asia, India, China, Australia, Cuba, among other producers, as by-products of the sugar and bioethanol industry. The sugarcane industry in Brazil and Uruguay is well established and expanding with large potential to increase the production of sugarcane bagasse in the next years [1-3]. Although the major portion of the bagasse is currently burnt for energy supply in the sugarcane industry, the disposal of this byproduct is still inefficient and, consequently, it is critical for agricu1ture profitability and environmental protection. Sugarcane bagasse is a lignocellu1ose fiber mainly constituted by around 46 % cellu1ose, containing hemicellu1ose, lignin, fat and waxes, silica and other elements [3, 4]. Studies have reported that sugarcane bagasse can be used to produce thermoplastic polymeric composites with excellent properties for many applications. [5-8]. Based on this survey, the transformation of bagasse into high quality industrial products, such as bagasse-polymer composites, can provide its more effective utilization."

Jan 1, 2012

By Marilda Macagnan, Rosana de Cassia de Souza Schneider, Valeriano Corbellini, Tiago Bjerk, Mariela de Souza Vieira

The great potential of Brazil for the agricultural production makes our country a generator of agro industrial residues. In this context, the solid-state fermentation appears as a technology that shows alternative ways for those residues, adding values to these raw materials, through the production of substances of industrial interest, besides reducing the possible environmental problems. The main objective of this study was to apply the bovine fat residue associated to the garden grass for the fungal lipase production. Initially, 75 microbial cultures were isolated from garden grass samples after incubation of the mixture with bovine fat. From these cultures were selected the filamentous fungi, whose lipase production abilities were evaluated. The isolation and the selection were accomplished by using a differential culture medium containing Tween 80 as inducer substrate of lipase production. The colonies with lipolytic potential were detected by the presence of white precipitation haloes on the agar. With agro industrial residues the best lipase producer fungus was identified as Penicillium sp in 6 days of solid state fermentation. The crude enzyme obtained was tested in transesterification process for the biodiesel production.

Jan 1, 2008

By Wellington Pereira Inácio, Fernando Wypych, Sergio Neves Monteiro, Artur Camposo Pereira, Rafael Marangoni

"The efficiency by which an applied load is transmitted from the matrix to reinforcing fibers in a composite depends on the fiber/matrix adhesion strength. This is determined as the interfacial shear strength, IFSS, which may be measured by means of pullout tests that measure the force needed to pull a single fiber out of a block of material simulating the composite matrix. Different techniques are used to perform pullout tests. The objective of this work was to characterize the IFSS of sisal fibers embedded in epoxy matrix through the determination of the critical length pullout curves. As the main results, a relatively small critical length was found for the sisal fiber/epoxy pullout specimens, corresponding to a weaker IFSS. This was compared to other results applying different pullout techniques. Scanning electron microscopy observation identified the mechanism responsible for the weak sisal fiber adhesion to the epoxy matrix.IntroductionSynthetic fiber reinforced composites is today one of the most successful class of materials with increasing industrial applications from house appliances to large airplanes like the modem Airbus 380. However, environmental issues are revealing serious drawbacks related to the fabrication, use and post-use discard of these composites. For instance, the thermoset polymer composite reinforced with E-glass fiber, known as ""fiberglass"" has an energy-intensive fabrication associated with a surplus emission of C02, which is responsible for global warming [1]. Moreover, the glass fiber is considered toxic and also causes long term pollution after being discarded."

Jan 1, 2011

By Walter E. McCulloch

Recent laboratory bench scale and pilot plant metallurgical tests at Mountain States R and D International have demonstrated that some copper ores because of relatively coarse copper sulfide mineralization can be preconcentrated by heavy media separation (HMS). In tests with a copper ore from the AMT Copper Creek project near San Manuel, Arizona, HMS preconcentration rejected about 75 to 80 percent of the feed as a minus 13 mm gravel. The HMS concentrates copper recoveries were about 93 to 95 percent. With the incorporation of HMS preconcentration, significant capital and operating costs savings have been projected for the proposed AMT Copper Creek concentrator. An overview of the HMS preconcentration step development for the AMT Copper Creek project is presented. Also presented are other potential applications of HMS preconcentration for copper ore processing.

Jan 1, 1999

By M. Misra

The prediction and assessment of the reactivity of acid mine tailings has been a subject of numerous studies. The conventional approaches such as sulfur content, pH, net acid generating capacity and conductivity are used for assessing reactivity of the tailings. In this paper a new non-invasive Impedance Spectroscopy (IS) technique is used for the determination of reactivity and acid mine potential of tailings. This technique is also used to establish the long term stability and leaching propensity of the tailings agglomerated with alkaline binders.

Jan 1, 1994

By Shenghui Guo, Jian Chen, Hongbo Zhu, Jinhui Peng, Linqing Dai, Qianxu Ye

"Response surface method (RSM) based on mono-factor experiment was applied for the process optimization of sintering of chromite fines by microwave. In RSM analysis, effects of binder addition amount, sintering temperature and holding time on the compression strength and shatter strength of the sinter were examined. Results showed that the optimal values of the above parameters were determined as follows: binder addition amount of 1.90% (in mass), sintering temperature of 1153? and holding time of 16 min. Under the optimized conditions, the compression strength was 11155.8? and shatter strength was 95.6849%. The results show that the process was optimized by response surface methodology is stable and feasible, and provide a new way for sintering of chromite fines.IntroductionChromite ore is the main feedstock for ferrochrome, and ferrochrome can be used as steelmaking additive to produce a variety of great strength, corrosion resistant and oxidation resistant special steel, which can be widely used in the aerospace, automotive, shipbuilding, military departments[1], and it has important strategic significance. At present, among the annual world's mined chromite the number of lump ore continues to diminish with its price rising sharply, while the proportion of ore fines been always increased, and the difference in prices between ore fines and lump ore is growing[2]. Despite the low price of chromite fines, and its rich in resources, it can be only used for ferrochrome smelting after agglomeration. Thus manufacturing blocks by using cheap chromite fines is an effective measure to reduce the cost of ferrochrome production and use the chromite resources[3]."

Jan 1, 2013

By Neil Smith

Mineral processing plants typically procure a range of industrial services from contractors. Their satisfaction and value received is directly affected by how the services are procured, rationalized and delivered. Conventional purchasing strategies often focus on price rather than on optimizing the service relationship between supplier and customer. The nature of this relationship may have the greatest potential to reduce costs and enhance production. It has been documented that a service involves simultaneous production and consumption. A high degree of customer involvement is often necessary for a successful outcome and the expectations and attitudes of the customer can positively or negatively affect delivery of the service. This indicates that the customer can enhance or diminish their own satisfaction and value received and the supplier cannot act alone for best results. The Optimax? Program for industrial services is a service delivery framework whereby a customer and supplier work together to raise the efficiency of the service exchange. The Optimax? Program is intended to help the customer optimize costs and maximize production by connecting the customer and supplier through shared information and objectives. This paper will review the basic nature of services, provide a couple of examples of conventional procurement strategies for services and outline the features of the Optimax? Program. A Case Study showing recent results from implementing the Optimax? Program will be included.

Jan 1, 2006

By Xiaohui Li, Lianyun Liu, Hongmin Zhu, Chunfang Zi, Kai Huang, Hongjie Li

"The dissolution kinetics of steelmaking slag in pure water was studied, and the relative influential factors were investigated. The dissolution behavior of slag particles in water was well described by Noyes–Whitney equation, and for this kind of sparingly soluble rigid mineral this simple model was extensively applicable to describe their dissolution process. Experimental data were also obtained to confirm the significant promotion effect on the growth of some algae.1 . IntroductionIt has been found that the population of phytoplankton distributed in the ocean was significantly related to the concentration of some elements [1]. For example, silicon and iron were very low in the high-nitrate low-chlorophyll (HNLC) areas, which was the main factor limiting phytoplankton and other biomass growth in these open ocean surface water [7]. The silicon and iron-rich test also confirmed that the supply of these elements had the direct effect on the growth of phytoplankton processes at HNLC areas [2-8]. So in order to promote the growth of phytoplankton in these ocean areas, providing some of these elements into these ocean areas is a natural idea for choice. Steelmaking slag is a good resource for consideration because it usually contains silicon, iron, phosphorus and other elements that are necessary for the growth of phytoplankton [8-10].Haraguchi has proposed the following idea that [5-6], if steelmaking slag can be spread to the open ocean, the trace components like silicate, iron and phosphate as the indispensable nutrients for the growth of phytoplankton, will be leached into the sea water, not only promoting the growth of phytoplankton, but also making good use of these huge amount of steelmaking slag produced every year. Based on this idea, they have carried out studies in recent years and they found that silicon and iron in the slag could be extracted into seawater effectively and play a positive role in the growth process of many algae. About the dissolution of the steelmaking slag, the Japanese scholars' research work mainly focused on the thermodynamic analysis of its dissolution possibility, and in the process of dissolution they tried to adjust the pH value of the seawater by continuously adding hydrochloric acid, which was deviated from the natural conditions of dissolution, and so the laws drawn under these special conditions can not give the identical guide to the practical application. Therefore, it is quite necessary to investigate the dissolution behavior of the steelmaking slag in the seawater at the normal pH range without adjustment to simulate the dissolution possibility under the natural conditions. In the present study, the silicon extraction behavior from the steelmaking slag was investigated and the dissolution kinetics in this process was also discussed in detail. Further studies were also performed here to evaluate the promotion of steelmaking slag on the growth of algae."

Jan 1, 2011

By J. van Driel

NOx is a growing concern for acid plant operators due to recent legislation reducing the allowable stack limits, as well as continually more stringent requirements for product acid quality. NOx also causes a major problem during maintenance as NOx rich acid residues fume following exposure to moisture in the air. Until recently, the solution for NOx related issues was to treat the symptom, rather than the cause. NOx in product acid was treated using chemicals and the NOx in the plant stack was generally left untreated. As part of an environmentally driven change in concentrates, Budel Zink installed the first gas phase NOx destruction process to be incorporated into a commercial scale acid plant. Nitrogen oxides contained in the process gas are reduced selectively with ammonia over a catalyst to form nitrogen and water. As a result, the NOx reduction is in agreement with the permit requirements.

Jan 1, 2002

By Norihiko Fukatsu, Takashi Iwamoto, Noriaki Kurita, Koji Katahira, Kunihiro Koide, Teruo Ohashi

"The galvanic cell-type hydrogen sensor employing CaZro.9Ino.t03-a. as the solid electrolyte was designed for the measurement of hydrogen activities in molten copper under industrial .conditions. The sensor probe consists of the cap-shaped solid electrolyte with porous platinum electrode on the inside and alumina refractory tube. The gas mixture of the composition 4%H2-0.5%02-Ar was made to flow on the inside electrode. The hydrogen sensor probe was inserted directly into molten copper and the melt was used as the outer electrode. The effect of oxygen activity gradient to EMF was eliminated theoretically by measuring the oxygen activity in the melt simultaneously with an oxygen sensor. The high stability of output and excellent response to the change of hydrogen activity were obtained over the wide range of industrial copper melting conditions.IntroductionIn the metal casting process, hydrogen easily dissolves in molten metals from water vapor in the surrounding atmosphere. Owing to the large difference in hydrogen solubility between liquid and solid metal, dissolved hydrogen becomes a cause of the defects of blowholes in castings or ingots. It is necessary to control the hydrogen content in the molten metals [l]. Using proton-conducting ceramics as a solid electrolyte, high temperature-type hydrogen sensor can be constructed [2]. SrCe03- and BaCe03-based perovskite-type oxides exhibit appreciable proton conduction under hydrogen containing atmosphere at high temperature [3-5]. A hydrogen sensor for molten aluminum using CaZro.91no.103-a. has been developed and widely used in the ·process control in the aluminum melting industry [6,7]. The same type of hydrogen sensor has also been expected in the copper melting industry. .. However, CaZro.91no.103-a shows ·not only proton but also oxide ion conduction in the high temperature and at low oxygen activies like the copper melting· conditions. Then we studied the oxide ion conduction in CaZro.91no.103-a. iit · detail [8]. From the consideration on the EMF of the galvanic cell employing this material as electrolyte, it was shown that the unknown hydrogen activity may be precisely determined from cell potential which is corrected for the effect of oxygen potential gradient And the hydrogen sensor based in this principle was constructed and tested in laboratory-scale [9,10]. We repeated the similar tests in factory-scale and developed the sensor system for practical uses [11, 12]. In this report, the structure and system of the hydrogen sensor for molten copper will be introduced first. The reliability of the sensor will then be demonstrated from the results of experiments for sensor probes carried out in TYK's laboratory."

Jan 1, 2000

By H. Y. Sohn

A novel solvent extraction process in which the emulsion is generated by bottom gas injection rather than mechanical stirring has been developed. This process has a number of advantages over the mixer-settler unit or the spray column in terms of simple equipment configuration and the ease of cleaning and process control while providing a large interfacial area for mass transfer. The equipment consists of a horizontal cylindrical vessel in which the two immiscible liquids flow countercurrently. High-strength gas jets are injected from the bottom at certain intervals along the length of the vessel. The gas jet creates a plume zone consisting of an emulsion of the two liquids which contains a large interfacial area for rapid mass transfer. The two liquids then disengage and flow in the opposite directions before entering another plume zone. Thus, the process combines the simplicity of a cylindrical vessel, having no moving parts, with the contacting efficiency of a mixer-settler. The gas can be recycled in a closed loop, thus eliminating mist and other emission problems. These advantages would be especially significant for treating large-volume/low-value liquid streams which contain hazardous substances and/or suspended solid particulates.

Jan 1, 1996

By Renato G. Bautista

"The development of processing methods for the preparation .of three electronic materials with rare-earth components is discussed. The resulting processing innovations are the results of a search for an economically competitive pilot scale or industrial production flowsheet without compromising the required properties of the final products. The three cases highlighted in this presentation are: 1) The preparation of high energy (Pr-Nd-Ce)FeB magnets for MRI application from a mixed-rare-earth oxide with a narrow range of composition directly prepared from the solvent extraction circuit of bastnaesite ore. 2) The kg production of the giant magnetocaloric effect Gds(SixGe1-x)4 magnetic refrigerant materials from commercial grade gadolinium metal (95 to 98 at. % pure) instead of high purity gadolinium metal (99.8 at. %); and 3). An industrial chemical synthesis flowsheet for the production of the superconductor precursor of YBa2Cu3O7.INTRODUCTIONIn the laboratory discovery stage, the synthesis of a new material is carried out using very high purity components, usually the highest purity available. As the new material is studied and characterized, the effectiveness of its desirable properties becomes better defined and understood. The evaluation of the effectiveness of the .property over the range of a given parameter and other interactions are further studied. Once it's potential application becomes clear, a practical and economical processing method need to be developed. The successful material processing flow sheet does not necessarily have to be a scale up of the laboratory procedure. At this stage, substitution of starting components and with lower purity materials is considered as the economics of the processing becomes a major issue. In addition, other approach to it's synthesis"

Jan 1, 2000

By T. Wang, R. G. Reddy

"The corrosion of stainless steel SS316L in a low melting point novel LiNO3-NaNO3-KNO3- NaNO2 eutectic molten salt mixture was investigated at 695K. After long-term isothermal dipping corrosion experiments, the SS316L samples were analyzed using scanning electron microscopy (SEM) equipped with energy dispersive spectrometer (EDS) to determine the topography and corrosion products. Dense and protective lithium iron oxide scale formed on the surface and prevented the SS316L sample from further severe corrosion. Therefore, SS316L is considered to be suitable construction material for solar thermal energy storage materials containers.IntroductionMolten salt mixtures have been considered as potential candidates for thermal energy storage and heat transfer media in solar energy applications. To apply the molten salt in the energy transfer process, the standard pipes made of stainless steel must be utilized to carry the molten salt mixtures in parabolic trough system of solar power production. The pipes encounter continuous flow of hot and cold molten salt every day. Thus corrosion of stainless steel in molten salt mixtures becomes extremely essential for the long-term utilization of the thermal energy storage media. The corrosion of passivity materials inside high temperature molten salt systems have been studied which gives fundamental understanding of basic mechanism about the corrosion process [1-8].The corrosion behavior of Fe-Ni-Cr alloys in an equi-molar LiNO3–NaNO3–KNO3 mixture was studied [9]. According to the XRD analyses, the major phases in the oxide scales were identified as LiFeO2, Fe3O4 and Cr2O3. A HITEC® salt mixture (NaNO3–NaNO2–KNO3) was also tested as a corrosion medium for stainless steel [10] and the corrosion rate was found to be affected by the protective oxide layer. In most cases, the alloys having more than 10wt% chromium show high resistance to corrosion in molten salts."

Jan 1, 2014